WQ8IA800-CAMMaxisys Intelligent ADAS IA800 Camera & AdaptorKit

i Trademarks Autel ® , MaxiSys ® , MaxiDAS ® , MaxiScan ® , MaxiTPMS ® , MaxiRecorder ® , and MaxiCheck ® are trademarks of Autel Intelligent Technology Corp., Ltd., registered in China, the United States and other countries. All other marks are trademarks or registered trademarks of their respective holders. Copyright Information No part of this manual may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise without the prior written permission of Autel. Disclaimer of Warranties and Limitation of Liabilities All information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Autel reserves the right to make changes at any time without notice. While information of this manual has been carefully checked for accuracy, no guarantee is given for the completeness and correctness of the contents, including but not limited to the product specifications, functions, and illustrations. Autel will not be liable for any direct, special, incidental, indirect damages or any economic consequential damages (including the loss of profits). IMPORTANT Before operating or maintaining this unit, please read this manual carefully, paying extra attention to the safety warnings and precautions. For Services and Support http://pro.autel.com www.autel.com 1-855-288-3587/1-855-AUTELUS (North America) 0086-755-22672493/86532091 (China) [email protected] For details, please refer to the Technical Support section in this manual. Model： AUTEL-CSC0500/06 ii Safety Information For your own safety and the safety of others, and to prevent damage to the device and vehicles upon which it is used, it is important that the safety instructions presented throughout this manual be read and understood by all persons operating or coming into contact with the device. There are various procedures, techniques, tools, and parts for servicing vehicles, as well as in the skill of the person doing the work. Because of the vast number of test applications and variations in the products that can be tested with this equipment, we cannot possibly anticipate or provide advice or safety messages to cover every circumstance. It is the automotive technician’s responsibility to be knowledgeable of the system being tested. It is crucial to use proper service methods and test procedures. It is essential to perform tests in an appropriate and acceptable manner that does not endanger your safety, the safety of others in the work area, the device being used, or the vehicle being tested. Before using the device, always refer to and follow the safety messages and applicable test procedures provided by the manufacturer of the vehicle or equipment being tested. Use the device only as described in this manual. Read, understand, and follow all safety messages and instructions in this manual. Safety Messages Safety messages are provided to help prevent personal injury and equipment damage. All safety messages are introduced by a signal word indicating the hazard level. DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury to the operator or to bystanders. WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury to the operator or to bystanders. Safety Instructions The safety messages herein cover situations Autel is aware of. Autel cannot know, evaluate or advise you as to all of the possible hazards. You must be certain that any condition or service procedure encountered does not jeopardize your personal safety. iii DANGER When an engine is operating, keep the service area WELL VENTILATED or attach a building exhaust removal system to the engine exhaust system. Engines produce carbon monoxide, an odorless, poisonous gas that causes slower reaction time and can lead to serious personal injury or loss of life. SAFETY WARNINGS  Always perform automotive testing in a safe environment.  Wear safety eye protection that meets ANSI standards.  Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.  Operate the vehicle in a well ventilated work area, for exhaust gases are poisonous.  Put the transmission in PARK (for automatic transmission) or NEUTRAL (for manual transmission) and make sure the parking brake is engaged.  Put blocks in front of the drive wheels and never leave the vehicle unattended while testing.  Be extra cautious when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running.  Keep a fire extinguisher suitable for gasoline, chemical, and electrical fires nearby.  Do not connect or disconnect any test equipment while the ignition is on or the engine is running.  Keep the test equipment dry, clean, free from oil, water or grease. Use a mild detergent on a clean cloth to clean the outside of the equipment as necessary.  Do not drive the vehicle and operate the test equipment at the same time. Any distraction may cause an accident.  Refer to the service manual for the vehicle being serviced and adhere to all diagnostic procedures and precautions. Failure to do so may result in personal injury or damage to the test equipment.  To avoid damaging the test equipment or generating false data, make sure the vehicle battery is fully charged and the connection to the vehicle DLC is clean and secure.  Do not place the test equipment on the distributor of the vehicle. Strong electro- magnetic interference can damage the equipment. iv Laser Radiation Never point the laser beam at people, particularly at their face or eyes. The term laser equipment refers to devices, systems or test set-ups generating, transmitting or employing laser radiation. The class of the laser device indicates the level of potential danger associated with its acc…

Text truncated - open the document above for the full version.

AutelIntelligentTech.Corp.,Ltd. OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USA Date:2020/11/13 Subject;RequestforConfidentiality FCCID:WQ8IA800-CAM ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,we arerequestingtheCommissiontowithholdthefollowingattachment(s)asconfidential documentsfrompublicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredas proprietaryinformationinoperationoftheequipment.Thepublicdisclosureofthesedocuments mightbeharmfultoourcompanyandwouldgivecompetitorsanunfairadvantageinthemarket. SchematicDiagram BlockDiagram OperationalDescription FCCSWSECURITYDESCRIPTION Inadditionaltoabovementioneddocuments,inordertocomplywiththemarketingregulations inTitle47CFR§2.803andtheimportationrulesinTitle47CFR§2.1204,whileensuringthat businesssensitiveinformationremainsconfidentialuntiltheactualmarketingofnewly authorizeddevices,werequestShortTermConfidentialityofthefollowingattachment(s); ExternalPhotos TestSetupPhotos InternalPhotos UserManual For45days,pursuanttoPublicNoticeDA04-1705. OR For180dayspursuanttoKDB726920D01. Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondenceduringthecertificationreviewprocesscannotbegrantedasconfidential documentsandthisinformationwillbeavailableforpublicreviewoncethegrantofequipment authorizationisissued. Sincerely, Signature: Name:FrankLi Title:President

AutelIntelligentTech.Corp.,Ltd. LetterofAuthorization Company:AutelIntelligentTech.Corp.,Ltd. Address:7th-8th,10thFloor,Bldg.B1,Zhiyuan,XueyuanRd.Xili,Nanshan, Shenzhen,China ProductName:MaxisysIntelligentADASIA800Camera&AdaptorKit ModelNumber(s):AUTEL-CSC0500/06 ProductDescription:MaxisysIntelligentADASIA800Camera&AdaptorKit WeauthorizeMiCOMLabsInc.,575BoulderCourt,Pleasanton,California94566,USA, toactonourbehalfonallmattersconcerningthecertificationofabovenamed equipment. WedeclarethatMiCOMLabsInc.isallowedtoforwardallinformationrelatedtothe approvalandcertificationofequipmenttotheregulatoryagenciesasrequiredandto discussanyissuesconcerningtheapprovalapplication.Anyandallactscarriedoutby MiCOMLabsonourbehalfshallhavethesameeffectasactsofourown. Signature:Date:13/11/2020 Name:FrankLi Title:President Company:AutelIntelligentTech.Corp.,Ltd.

FCCID:WQ8IA800-CAM

LabelLocation:

ProductName:MaxisysIntelligentADASIA800 Camera&AdaptorKit ModelNo.:AUTEL-CSC0500/06 FCCID:WQ8IA800-CAM ThisdevicecomplieswithPart15oftheFCCRules.Operation issubjecttothefollowingtwoconditions: (1)Thisdevicemaynotcauseharmfulinterference,and (2)Thisdevicemustacceptanyinterferencereceived,including interferencethatmaycauseundesiredoperation.

FCCID:WQ8IA800-CAM ANTA ANTB

RFEXPOSUREEVALUATION AccordingtoFCC1.1310:Thecriterialistedinthefollowingtableshallbeusedto evaluatetheenvironmentimpactofhumanexposuretoradiofrequency(RF)Radiation asspecifiedin§1.1307(b) FCCID:WQ8IA800-CAM EUTSpecification EUTMaxisysIntelligentADASIA800Camera&AdaptorKit Frequencyband(Operating)WLAN:2.412GHz~2.462GHz WLAN:5.18GHz~5.24GHz WLAN:5.745GHz~5.825GHz Others:2.402GHz~2.480GHz DevicecategoryPortable(<20cmseparation) Mobile(>20cmseparation) Others___ ExposureclassificationOccupational/Controlledexposure(S=5mW/cm2) GeneralPopulation/Uncontrolledexposure(S=1mW/cm2) AntennadiversitySingleantenna Multipleantennas Txdiversity Rxdiversity Tx/Rxdiversity Max.outputpower2.4GWiFi:18.18dBm(0.0657W) 5.1GWiFi:18.99dBm(0.0793W) 5.8GWiFi:17.32dBm(0.0540W) Antennagain(Max)WiFi2.4G:ANTA&ANTB3.9dBi WiFi5.1G&WiFi5.8G:ANTA&ANTB3.9dBi EvaluationappliedMPEEvaluation SAREvaluation LimitsforMaximumPermissibleExposure(MPE) Frequency Range(MHz) ElectricField Strength(V/m) MagneticField Strength(A/m) Power Density(mW/cm 2 ) Average Time (A)LimitsforOccupational/ControlExposures 300-1500----F/3006 1500-100000----56 (B)LimitsforGeneralPopulation/UncontrolExposures 300-1500----F/15006 1500-100000----130 Friistransmissionformula:Pd=(Pout*G)\(4*pi*R2) Where Pd=PowerdensityinmW/cm 2 Pout=outputpowertoantennainMw G=gainofantennainlinearscale Pi=3.1416 R=distancebetweenobservationpointandcenteroftheradiatorincm PdthelimitofMPE,1mW/cm2.Ifweknowthemaximumgainoftheantennaand totalpowerinputtotheantenna,throughthecalculation,wewillknowthedistance wheretheMPElimitisreached. MeasurementResult 2.4GWiFiANTA: Operating Mode Channel Frequency (MHz) Measured Power (dBm) Tuneup tolerance (dBm) Max.Tune upPower (dBm) Antenna Gain (dBi) Powerdensity at20cm (mW/cm 2 ) Powerdensity Limits (mW/cm 2 ) 802.11g 241214.87 14.87±1 15.873.90.01891 243714.3414.34±115.343.90.01671 246213.81 13.81±1 14.813.90.01481 802.11n (HT20) 241215.10 15.10±1 16.13.90.01991 243714.5214.52±115.523.90.01741 246215.10 15.10±1 16.13.90.01991 2.4GWiFiANTB: Operating Mode Channel Frequency (MHz) Measured Power (dBm) Tuneup tolerance (dBm) Max.Tune upPower (dBm) Antenna Gain (dBi) Powerdensity at20cm (mW/cm 2 ) Powerdensity Limits (mW/cm 2 ) 802.11g 241215.31 15.31±1 16.313.90.02091 243714.61 14.61±1 15.613.90.01781 246214.2814.28±115.283.90.01651 802.11n (HT20) 241215.2415.24±116.243.90.02051 243714.9014.90±115.93.90.01901 246214.4814.48±115.483.90.01721 ANTA+ANTB Operating Mode Channel Frequency (MHz) ANTA Powerdensityat20cm (mW/cm 2 ) ANTB Powerdensityat20cm (mW/cm 2 ) ANTA+ANTB Powerdensityat 20cm (mW/cm 2 ) Powerdensity Limits (mW/cm 2 ) 802.11n (HT20) 24120.01990.02050.04041 24370.01740.01900.03641 24620.01990.01720.03711 5.1GWiFiANTA: Operating Mode Channel Frequency Measured Power Tuneup tolerance Max.Tuneup Power AntennaGain Powerdensityat 20cm Powerdensity Limits (mW/cm2) (MHz)(dBm)(dBm)(dBm)(dBi)(mW/cm2) 802.11a 5180 15.13 15.13±1 16.133.90.0200 1 5200 15.81 15.81±1 16.813.90.0234 1 524015.6715.67±116.673.90.02271 802.11n20 5180 14.60 14.60±1 15.63.90.0177 1 5200 14.73 14.73±1 15.733.90.0183 1 524014.8614.86±115.863.90.01881 802.11ac20 5180 14.92 14.92±1 15.923.90.0191 1 5200 15.08 15.08±1 16.083.90.0198 1 524014.8414.84±115.843.90.01871 802.11n40 5190 15.84 15.84±1 16.843.90.0236 1 5230 15.69 15.69±1 16.693.90.0228 1 802.11ac40 519015.5515.55±116.553.90.02211 5230 15.28 15.28±1 16.283.90.0207 1 802.11ac805210 15.41 15.41±1 16.413.90.0214 1 5.1GWiFiANTB: ANTA+ANTB: Operating Mode Channel Frequency Measured Power Tuneup tolerance Max.Tuneup Power AntennaGain Powerdensityat 20cm Powerdensity Limits (mW/cm2) (MHz)(dBm)(dBm)(dBm)(dBi)(mW/cm2) 802.11a 5180 15.86 15.86±1 16.863.90.0237 1 520015.2715.27±116.273.90.02071 524015.7715.77±116.773.90.02321 802.11n20 5180 15.21 15.21±1 16.213.90.0204 1 520015.5415.54±116.543.90.02201 524015.8215.82±116.823.90.02351 802.11ac20 5180 14.85 14.85±1 15.853.90.0188 1 520015.0515.05±116.053.90.01971 524014.8714.87±115.873.90.01891 802.11n40 5190 16.12 16.12±1 17.123.90.0252 1 523015.9015.90±116.93.90.02391 802.11ac40 519015.9515.95±116.953.90.02421 5230 15.45 15.45±1 16.453.90.0216 1 802.11ac80521015.2615.26±116.263.90.02061 Operating Mode Channel Frequency ANTA Powerdensityat20cm ANTB Powerdensityat20cm ANTA+ANTB Powerdensityat20cm PowerdensityLimits (MHz)(mW/cm2)(mW/cm2)(mW/cm2)(mW/cm2) 802.11a 51800.02000.02370.03821 52000.02340.02070.04021 52400.02270.02320.04231 802.11n20 51800.01770.02040.03791 52000.01830.02200.03951 52400.01880.02350.03761 802.11ac20 51800.01910.01880.04871 52000.01980.01970.04671 52400.01870.01890.04621 802.11n40 51900.02360.02520.04231 52300.02280.02390.04201 802.11ac40 51900.02210.02420.03821 52300.02070.02160.04021 802.11ac8052100.02140.02060.04231 5.8GWiFiANTA: 5.8GWiFiANTB: Operating Mode Channel Frequency Measured Power Tuneup tolerance Max.Tuneup Power AntennaGain Powerdensityat 20cm Powerdensity Limits (mW/cm2) (MHz)(dBm)(dBm)(dBm)(dBi)(mW/cm2) 802.11a 5745 14.73 14.73±1 15.733.90.0183 1 578514.9214.92±115.923.90.01911 582514.6014.60±115.63.90.01771 802.11n20 5745 13.31 13.31±1 14.313.90.0132 1 13.3113.3113.31±114.363.90.01331 582514.5614.56±115.563.90.01761 802.11ac20 5745 14.04 14.04±1 15.043.90.0156 1 578514.5414.54±115.543.90.01751 582513.7913.79±114.793.90.01471 802.11n40 5755 14.80 14.80±1 15.83.90.0186 1 579514.5914.59±115.593.90.01771 802.11ac40 575514.6714.67±115.673.90.01801 5795 14.84 14.84±1 15.843.90.0187 1 802.11ac80577515.0215.02±116.023.90.01951 Operating Mode Channel Frequency Measured Power Tuneup tolerance Max.Tuneup Power AntennaGain Powerdensityat 20cm Powerdensity Limits (mW/cm2) (MHz)(dBm)(dBm)(dBm)(dBi)(mW/cm2) 802.11a 5745 12.62 12.62±1 13.623.90.0112 1 578512.5812.58±113.583.90.01111 582512.0012.00±1133.90.00971 802.11n20 5745 11.92 11.92±1 12.923.90.0096 1 578512.3012.30±113.33.90.01041 582511.9711.97±112.973.90.00971 802.11ac20 5745 11.85 11.85±1 12.853.90.0094 1 578512.0612.06±113.063.90.00991 582511.5811.58±112.583.90.00881 802.11n40 5755 13.75 13.75±1 …

Text truncated - open the document above for the full version.

ReportNo.:18220WC00140801FCCID:WQ8IA800-CAMPage1of71 Code:AB-RF-05-a FCCTESTREPORT ClientName:AutelIntelligentTech.Corp.,Ltd. Address: 7th-8th,10thFloor,Bldg.B1,Zhiyuan,XueyuanRd.Xili, Nanshan,Shenzhen,China ProductName:MaxisysIntelligentADASIA800Camera&AdaptorKit Date:Nov.13,2020 ShenzhenAnbotekComplianceLaboratoryLimited ReportNo.:18220WC00140801FCCID:WQ8IA800-CAMPage2of71 Code:AB-RF-05-a Contents 1.GeneralInformation ............................................................................................................................................... 5 1.1.ClientInformation ....................................................................................................................................... 5 1.2.DescriptionofDevice(EUT) ..................................................................................................................... 5 1.3.AuxiliaryEquipmentUsedDuringTest ................................................................................................... 6 1.4.DescriptionofTestModes ........................................................................................................................ 6 1.5.Listofchannels ........................................................................................................................................... 8 1.6.DescriptionOfTestSetup ......................................................................................................................... 9 1.7.TestEquipmentList .................................................................................................................................. 10 1.8.MeasurementUncertainty ....................................................................................................................... 11 1.9.DescriptionofTestFacility ...................................................................................................................... 11 2.SummaryofTestResults ................................................................................................................................... 12 3.ConductedEmissionTest ................................................................................................................................... 13 3.1.TestStandardandLimit .......................................................................................................................... 13 3.2.TestSetup .................................................................................................................................................. 13 3.3.TestProcedure .......................................................................................................................................... 13 3.4.TestData .................................................................................................................................................... 13 4.RadiationSpuriousEmissionandBandEdge ................................................................................................ 18 4.1.TestStandardandLimit .......................................................................................................................... 18 4.2.TestSetup .................................................................................................................................................. 18 4.3.TestProcedure .......................................................................................................................................... 19 4.4.TestData .................................................................................................................................................... 20 5.MaximumPeakOutputPowerTest .................................................................................................................. 37 5.1.TestStandardandLimit .......................................................................................................................... 37 5.2.TestSetup .................................................................................................................................................. 37 5.3.TestProcedure .......................................................................................................................................... 37 5.4.TestData .................................................................................................................................................... 37 6.6DBOccupyBandwidthTest ............................................................................................................................. 42 6.1.TestStandardandLimit .......................................................................................................................... 42 6.2.TestSetup .................................................................................................................................................. 42 6.3.TestProcedure .......................................................................................................................................... 42 6.4.TestData .................................................................................................................................................... 42 7.PowerSpectralDensityTest .............................................................................................................................. 51 7.1.TestStandardandLimit .......................................................................................................................... 51 7.2.TestSetup .................................................................................................................................................. 51 7.3.TestProcedure .......................................................................................................................................... 51 7.4.TestData ....................................................................................................…

Text truncated - open the document above for the full version.

FCCID:WQ8IA800-CAM PhotoofPowerLineConductedEmissionTest PhotoofRadiationEmissionTest