WR3MOD16370915Sub-1G Module

MOD-16370-915 Sub-1G Module User Guide OMEGA Engineering, Inc. V1.0 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 23cm between the radiator & your body. This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module: KDB 996369 D03 OEM Manual v01 rule sections: 2.2 List of applicable FCC rules This module has been tested for compliance to FCC Part 15 2.3 Summarize the specific operational use conditions The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as co-location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification. 2.4 Limited module procedures Not applicable. 2.5 Trace antenna designs Not applicable. 2.6 RF exposure considerations This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 23cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules. 2.7 Antennas The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 23 cm can be maintained between the antenna and users. 2.8 Label and compliance information The final end product must be labeled in a visible area with the following: “Contains FCC ID: WR3MOD16370915”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. 2.9 Information on test modes and additional testing requirements This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification. 2.10 Additional testing, Part 15 Subpart B disclaimer This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end- product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. OEM/Host manufacturer responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into any other device or system without retesting for compliance as multi-radio and combined equipment. Industry Canada statement This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditi…

Text truncated - open the document above for the full version.

UNRESTRICTED Professional Installation Attestation Date: 2020-09-01 FCC ID: WR3MOD16370915 We, OMEGA Engineering, Inc. hereby declare that requirements of KDB 353028 D01 Antennas Part 15 Transmitters v01 have been met and shown on the following questions. Further we declare that the info listed below are correct and represent the product in consideration under this filing. 1. Professional installation must be justified. Description: Device is Sub-1G module and needs special trained professional in configuring and installing the product. 2. Professional installation does not permit use of any antenna with the transmitter; the permitted types of antenna specified as below. Description: Below listed of Antennas has been compliance FCC Rule Part 15 requirement, more details please refer to test reports. 3. The applicant should address the following items when justifying professional installation. (1) To qualify for professional installation, please explain why the hardware is not readily available to average consumer. Description: This product is for use solely in other products manufactured by Omega Engineering Inc. or its designated suppliers only and will not be sold directly to the general public; therefore, the hardware is not readily available to average consumer. (2) Marketing — Applicant must ensure device cannot be sold via retail to the general public or by mail order. Description: This product will not be sold directly to the general public through retail store. It will be sold to authorized dealers or installers only. UNRESTRICTED (3) Applicant must show that device intended use is not for consumers and general public. Description: The Device is a module that has no standalone functionality. It must be programmed and integrated into a final product. (4) Explain what is unique, sophisticated, complex, or specialized about the equipment that REQUIRES it to be installed by a professional installer? Description: The Device needs a complex selection of proper sensor(s), Tx type, power level and software to meet each individual product requirement. 4. Other professional installation requirements (1) Installation must be controlled. Description: The device is for use solely in products manufactured by Omega Engineering Inc. or its designated suppliers and will be distributed through a controlled distribution channel which has specially trained professionals to install this product (2) Installed by licensed professionals. Description: The device will be installed by Omega Engineering Inc. or its designated suppliers only. (3) Installation requires special training. Description: The device needs a complex selection of proper sensor, Tx type, power level and software to meet each individual product requirement. If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ------------------------------------------ Suzanne Babic Compliance Specialist Omega Engineering, Inc. Tel: 203-359-7741 Fax: 203-968-7185 E-mail: [email protected]

FCC ID: WR3MOD16370915 Report No.: RF191014C04 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch March 20, 2020 Dear Application Examiner, Omega Engineering, Inc., Sub-1G Module, FCC ID: WR3MOD16370915 would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of KDB996369 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip CC1312R. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is CC1190. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a USB extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: WR3MOD16370915 Report No.: RF191014C04 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Andrea Hsia / Supervisor Electrical & Electronic Automotive Wireless - Bureau Veritas Consumer Products Services No. 19, Huaya 2nd Rd., Guishan Dist., Taoyuan City 33383, Taiwan (R.O.C.), 33383 T: +886-3-318-3232 | M: +886-963-588-283

CONFIDENTIAL Date: 2020-09-01 Federal Communications Commission Laboratory Division 7435 Oakland Mills Road Columbia, MD 21046 Attention: Office of Engineering and Technology Re: Supersede request for FCC ID: WR3MOD16370915 As notified by the TCB, we are aware that the grant condition for our previous certified product (FCC ID: WR3MOD16370915) needs to be updated to professional installation only due to the use of standard antenna connector. This product is intended for integration by OEM’s only and will need a trained professional to configure the proper sensor, antenna, transmitter and control software to meet the product application need and indeed requires a professional installation. We hereby declare that the product associated with FCC ID: WR3MOD16370915 has not been marketed or sold as a standalone product in the United States as well as anywhere in the world with this FCC identifier on it and the update of grant condition will not cause any incompliance. Thank you and we appreciate your help! Sincerely, ------------------------------------------ Suzanne Babic Compliance Specialist Omega Engineering, Inc. Tel: 203-359-7741 Fax: 203-968-7185 E-mail: [email protected]

Reference No.: 191014C04-1 Page No. 1 / 9 CONSTRUCTION PHOTOS OF EUT Reference No.: 191014C04-1 Page No. 2 / 9 Reference No.: 191014C04-1 Page No. 3 / 9 Model: HG905RD-RSP Reference No.: 191014C04-1 Page No. 4 / 9 Model: HG8909P Reference No.: 191014C04-1 Page No. 5 / 9 Model: HG912YE Reference No.: 191014C04-1 Page No. 6 / 9 Reference No.: 191014C04-1 Page No. 7 / 9 Model: HG908U-PRO Reference No.: 191014C04-1 Page No. 8 / 9 Model: RFDPA171300SBRB804 Reference No.: 191014C04-1 Page No. 9 / 9

FCC ID: WR3MOD16370915 The label will be permanently affixed and readily visible. Label

Reference No.: 191014C04-2 Page No. 1 / 1 CONSTRUCTION PHOTOS OF EUT

Report No.: SA191014C04 Page No. 1 / 5 Report Format Version: 6.1.1 RF Exposure Report Report No.: SA191014C04 FCC ID: WR3MOD16370915 Test Model: MOD-16370-915 Received Date: Oct. 14, 2019 Test Date: Oct. 22 ~ Nov. 06, 2019 Issued Date: Nov. 08, 2019 Applicant: OMEGA Engineering, Inc. Address: 800 Connecticut Ave., Suite 5N01,Norwalk, CT 06854, USA. Manufacturer: Fitivision Technology Inc. Address: 11494 No. 13-22,2F,Section 6,Minquan East Rd., Neihu District, Taipei City,Taiwan (R.O.C) Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: SA191014C04 Page No. 2 / 5 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 3 Calculation Result Of Maximum Conducted Power .......................................................................... 5 Report No.: SA191014C04 Page No. 3 / 5 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued SA191014C04 Original release. Nov. 08, 2019 Report No.: SA191014C04 Page No. 4 / 5 Report Format Version: 6.1.1 1 Certificate of Conformity Product: Sub-1G Module Brand: OMEGA Test Model: MOD-16370-915 Sample Status: Engineering sample Applicant: OMEGA Engineering, Inc. Test Date: Oct. 22 ~ Nov. 06, 2019 Standards: FCC Part 2 (Section 2.1091) References Test Guidance: KDB 447498 D01 General RF Exposure Guidance v06 IEEE C95.3 -2002 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date:Nov. 08, 2019 Polly Chien / Specialist Approved by : , Date:Nov. 08, 2019 Bruce Chen / Senior Project Engineer Report No.: SA191014C04 Page No. 5 / 5 Report Format Version: 6.1.1 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 23cm away from the body of the user. So, this device is classified as Mobile Device. 3 Calculation Result Of Maximum Conducted Power Frequency Band (MHz) Max Power (dBm) Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) Test Mode A 902.4 ~ 927.6 23.85 5 23 0.115 0.602 Test Mode B 902.4 ~ 927.6 23.85 8 23 0.230 0.602 Test Mode C 902.4 ~ 927.6 23.85 9 23 0.290 0.602 Test Mode D 902.4 ~ 927.6 23.85 12 23 0.579 0.602 Note: Determining compliance based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. ---END---

Report No.: RF191014C04 Page No. 1 / 86 Report Format Version: 6.1.1 FCC Test Report Report No.: RF191014C04 FCC ID: WR3MOD16370915 Test Model: MOD-16370-915 Received Date: Oct. 14, 2019 Test Date: Oct. 22 ~ Nov. 06, 2019 Issued Date: Nov. 08, 2019 Applicant: OMEGA Engineering, Inc. Address: 800 Connecticut Ave., Suite 5N01,Norwalk, CT 06854, USA. Manufacturer: Fitivision Technology Inc. Address: 11494 No. 13-22,2F,Section 6,Minquan East Rd., Neihu District, Taipei City,Taiwan (R.O.C) Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RF191014C04 Page No. 2 / 86 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT ................................................................................................................ 7 3.2 Description of Test Modes ................................................................................................................... 8 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 9 3.3 Description of Support Units ............................................................................................................. 10 3.3.1 Configuration of System under Test .................................................................................................. 10 3.4 General Description of Applied Standards and References ............................................................. 10 4 Test Types and Results ....................................................................................................................... 11 4.1 Radiated Emission and Bandedge Measurement .............................................................................. 11 4.1.1 Limits of Radiated Emission and Bandedge Measurement ............................................................... 11 4.1.2 Test Instruments ................................................................................................................................ 12 4.1.3 Test Procedures ................................................................................................................................. 13 4.1.4 Deviation from Test Standard ............................................................................................................ 13 4.1.5 Test Setup .......................................................................................................................................... 14 4.1.6 EUT Operating Conditions ................................................................................................................. 15 4.1.7 Test Results ....................................................................................................................................... 16 4.2 Conducted Emission Measurement .................................................................................................. 64 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 64 4.2.2 Test Instruments ................................................................................................................................ 64 4.2.3 Test Procedures ................................................................................................................................. 65 4.2.4 Deviation from Test Standard ............................................................................................................ 65 4.2.5 Test Setup .......…

Text truncated - open the document above for the full version.

Reference No.: 191014C04 Page No. 1 / 12 PHOTOGRAPHS OF THE TEST CONFIGURATION Conducted Emission Test Mode A Reference No.: 191014C04 Page No. 2 / 12 Conducted Emission Test Mode B Reference No.: 191014C04 Page No. 3 / 12 Conducted Emission Test Mode C Reference No.: 191014C04 Page No. 4 / 12 Conducted Emission Test Mode D Reference No.: 191014C04 Page No. 5 / 12 Radiated Emission Test (Above 1GHz) Mode A Reference No.: 191014C04 Page No. 6 / 12 Radiated Emission Test (Above 1GHz) Mode B Reference No.: 191014C04 Page No. 7 / 12 Radiated Emission Test (Above 1GHz) Mode C Reference No.: 191014C04 Page No. 8 / 12 Radiated Emission Test (Above 1GHz) Mode D Reference No.: 191014C04 Page No. 9 / 12 Radiated Emission Test (Below 1GHz) Mode A Reference No.: 191014C04 Page No. 10 / 12 Radiated Emission Test (Below 1GHz) Mode B Reference No.: 191014C04 Page No. 11 / 12 Radiated Emission Test (Below 1GHz) Mode C Reference No.: 191014C04 Page No. 12 / 12 Radiated Emission Test (Below 1GHz) Mode D