WVBAC622XCDMA mobile phone

FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.  RF Exposure Information (SAR) This phone is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States. During SAR testing, this device was set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage against the head with no separation, and near the body with the separation of 15 mm. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The exposure standard for wireless devices employing a unit of measurement is known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. This device is complied with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-1992 and had been tested in accordance with the measurement methods and procedures specified in IEEE1528. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: WVBAC622X. For this device, the highest reported SAR value for usage against the head is 1.13 W/kg, for usage near the body is 1.00 W/kg. While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirements. SAR compliance for body-worn operation is based on a separation distance of 15 mm between the unit and the human body. Carry this device at least 15 mm away from your body to ensure RF exposure level compliant or lower to the reported level. To support body-worn operation, choose the belt clips or holsters, which do not contain metallic components, to maintain a separation of 15 mm between this device and your body. RF exposure compliance with any body-worn accessory, which contains metal, was not tested and certified, and use such body-worn accessory should be avoided. Safety Precautions Please read these simple guidelines. Not following them may be dangerous or illegal. For further information, see the section of “Warnings and Precautions”. Do not switch the phone on when Mobile Phone use is prohibited or when it may cause interference or danger. Do not place your phone and its accessories in containers with strong electromagnetic field. Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety. Hospitals or health care facilities may be using equipment that could be sensitive to external radio frequency energy. Follow any regulations or rules in force. Do not use the phone at a refueling point. Do not use near fuel or chemicals. Follow any restrictions. Wireless devices can cause interference in aircraft. Keep the phone and all its parts, including accessories, out of the reach of small children. Use only approved batteries and chargers. Disconnect the charger from the power source when it is not in use. Do not leave the battery connected to a charger for more than a week, since overcharging may shorten its lift. Only qualified personnel should service the phone or install the phone in a vehicle. Faulty installation or service may be dangerous and may invalidate any warranty applicable to the device. i Content .1 Getting to Know Your Phone ....................................................................................... 1 Basic specification ........................................................................................................... 1 Phone Overview .............................................................................................................. 2 .2 Getting Started ............................................................................................................ 9 Installing the battery ......................................................................................................... 9 Charging the battery ....................................................…

Text truncated - open the document above for the full version.

Brightstar Corporation 9725 NW 117th Ave.,Miami,Florida,United States,33178 Tel: 1 305.921-1470; Fax: 1 305.863-3367 Date: December 7, 2015 Statement We, Brightstar Corporation, states that our device, FCC ID: WVBAC622X. The label will put under the battery inside the battery compartment and it is visible to the users as they purchase the products and install the battery. Sincerely yours, _______________ Welton Giolo

Rev. 1/1/03 Brightstar Corporation 9725 NW 117th Ave.,Miami,Florida,United States,33178 Tel: 1 305.921-1470 ; Fax: 1 305.863-3367 Date: December 7, 2015 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: WVBAC622X Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Schematics Block Diagram Parts List Operation Description Tune up Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ________________________ Welton Giolo

Brightstar Corporation 9725 NW 117th Ave.,Miami,Florida,United States,33178 Tel: 1 305.921-1470 ; Fax: 1 305.863-3367 Date: December 7, 2015 Power of Attorney To whom it may concern, Please be notified that I, Welton Giolo, have designated Michael Lin in Sporton International Inc. as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Michael Lin in Sporton International Inc. on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 835(a). This authorization is limited to the product of as following: FCC ID: WVBAC622X If you have any acknowledgement and response, please send it to Sporton International Inc. directly. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely yours, Contact Person: Welton Giolo Company: Brightstar Corporation TEL: 1 305.921-1470 FAX: 1 305.863-3367 E-mail: [email protected]

1/1 Brightstar Corporation Date: December 7, 2015 Federal Communications Commission Authorization and Evaluation Division RE : Certification Application FCC ID : WVBAC622X To Whom It May Concern, Pursuant to sections 0.457 and 0.459 of CFR 47, Public Notice DA 04-1705 of the Commission’s policy and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 180 days:  External Photos  Internal Photos  Test set-up photos  Users Manual The application contains technical information, which Brightstar Corporation deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application Sincerely, Contact Person: Welton Giolo Company: Brightstar Corporation TEL: 1 305.921-1470 FAX: 1 305.863-3367 E-mail: [email protected]

Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 1 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X 1. External Photograph of EUT Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 2 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 3 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 4 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 5 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 6 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 7 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X Specification of Accessory AC Adapter Brand Name Avvio Model Name S050-050-US Battery Brand Name Avvio Model Name BL-5C Earphone Signal Line Type 1.0m, non-shielded cable, without ferrite core USB Cable Signal Line Type 0.9m, shielded cable, without ferrite core Remark: For accessories equipped with this EUT, please refer to the following photos. 2. Photograph of Accessory Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 8 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 9 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X AC Adapter Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 10 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X Battery Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 11 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X

Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 12 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X 3. Internal Photograph of EUT WWAN Antenna <Tx/Rx> Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 13 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 14 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 15 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 16 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 17 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 18 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 19 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 20 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X Photographs of EUT Report No.: EP5D0405 Brand Name: Avvio / Model Name: Avvio C622 SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 21 of 21 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X WWAN Antenna <Tx/Rx>

SPORTON INTERNATIONAL (SHENZHEN) INC. TEL : 86-755-8637-9589/ FAX : 86-755-8637-9595 Issued Date : Dec. 29, 2015 FCC ID : WVBAC622X Page 1 of 30 Form version. : 151208 FCC SAR Test Report Report No. : FA5D0405 FCC SAR Test Report APPLICANT : Brightstar Corporation EQUIPMENT : CDMA mobile phone BRAND NAME : Avvio MODEL NAME : Avvio C622 FCC ID : WVBAC622X STANDARD : FCC 47 CFR Part 2 (2.1093) ANSI/IEEE C95.1-1992 IEEE 1528-2013 We, SPORTON INTERNATIONAL (SHENZHEN) INC., would like to declare that the tested sample has been evaluated in accordance with the procedures and had been in compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL (SHENZHEN) INC., the test report shall not be reproduced except in full. SPORTON INTERNATIONAL (SHENZHEN) INC. 1F & 2F, Building A, Morning Business Center, No. 4003 ShiGu Rd., Xili Town, Nanshan District, Shenzhen, Guangdong, P. R. China Approved by: Jones Tsai / Manager Prepared by: Mark Qu / Manager SPORTON INTERNATIONAL (SHENZHEN) INC. TEL : 86-755-8637-9589/ FAX : 86-755-8637-9595 Issued Date : Dec. 29, 2015 FCC ID : WVBAC622X Page 2 of 30 Form version. : 151208 FCC SAR Test Report Report No. : FA5D0405 Table of Contents 1. Statement of Compliance ............................................................................................................................................. 4 2. Administration Data ...................................................................................................................................................... 5 3. Guidance Standard ....................................................................................................................................................... 5 4. Equipment Under Test (EUT) Information ................................................................................................................... 6 4.1 General Information ............................................................................................................................................... 6 5. RF Exposure Limits....................................................................................................................................................... 7 5.1 Uncontrolled Environment ...................................................................................................................................... 7 5.2 Controlled Environment .......................................................................................................................................... 7 6. Specific Absorption Rate (SAR) ................................................................................................................................... 8 6.1 Introduction ............................................................................................................................................................ 8 6.2 SAR Definition ........................................................................................................................................................ 8 7. System Description and Setup .................................................................................................................................... 9 7.1 E-Field Probe ........................................................................................................................................................10 7.2 Data Acquisition Electronics (DAE) .......................................................................................................................10 7.3 Phantom ................................................................................................................................................................ 11 7.4 Device Holder........................................................................................................................................................12 8. Measurement Procedures ...........................................................................................................................................13 8.1 Spatial Peak SAR Evaluation ................................................................................................................................13 8.2 Power Reference Measurement............................................................................................................................14 8.3 Area Scan .............................................................................................................................................................14 8.4 Zoom Scan ............................................................................................................................................................15 8.5 Volume Scan Procedures ......................................................................................................................................15 8.6 Power Drift Monitoring ...........................................................................................................................................15 9. Test Equipment List .....................................................................................................................................................16 10. System Verification ....................................................................................................................................................17 10.1 Tissue Verification ...............................................................................................................................................17 10.2 System Performance Check Results ...................................................................................................................18 11. RF Exposure Positions ..................................................................................................…

Text truncated - open the document above for the full version.

SPORTON INTERNATIONAL (SHENZHEN) INC. TEL : 86-755-8637-9589/ FAX : 86-755-8637-9595 Issued Date : Dec. 29, 2015 FCC ID : WVBAC622X Page C1 of C1 Form version. : 151208 FCC SAR Test Report Report No. : FA5D0405 Appendix C. DASY Calibration Certificate The DASY calibration certificates are shown as follows.

SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 1 of 23 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X FCC RF Test Report Report No. : FG5D0405 FCC RF Test Report APPLICANT : Brightstar Corporation EQUIPMENT : CDMA mobile phone BRAND NAME : Avvio MODEL NAME : Avvio C622 FCC ID : WVBAC622X STANDARD : FCC 47 CFR Part 2, 22(H), 24(E) CLASSIFICATION : PCS Licensed Transmitter Held to Ear (PCE) The product was received on Dec. 04, 2015 and testing was completed on Dec. 15, 2015. We, SPORTON INTERNATIONAL (SHENZHEN) INC., would like to declare that the tested sample has been evaluated in accordance with the test procedures given in ANSI / TIA / EIA-603-D-2010 and has been in compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL (SHENZHEN) INC., the test report shall not be reproduced except in full. Prepared by: Andy Yeh / Manager Approved by: Jones Tsai / Manager SPORTON INTERNATIONAL (SHENZHEN) INC. 1F & 2F, Building A, Morning Business Center, No. 4003 ShiGu Rd., Xili Town, Nanshan District, Shenzhen, Guangdong, P. R. China SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : 2 of 23 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X FCC RF Test Report Report No. : FG5D0405 TABLE OF CONTENTS 1 GENERAL DESCRIPTION .......................................................................................................................... 5 1.1 Applicant ............................................................................................................................................ 5 1.2 Manufacturer ..................................................................................................................................... 5 1.3 Product Feature of Equipment Under Test ....................................................................................... 5 1.4 Product Specification subjective to this standard .............................................................................. 6 1.5 Modification of EUT ........................................................................................................................... 6 1.6 Maximum ERP/EIRP Power, Frequency Tolerance, and Emission Designator ............................... 7 1.7 Testing Location ................................................................................................................................ 7 1.8 Applicable Standards ........................................................................................................................ 8 2 TEST CONFIGURATION OF EQUIPMENT UNDER TEST ........................................................................ 9 2.1 Test Mode.......................................................................................................................................... 9 2.2 Connection Diagram of Test System .............................................................................................. 10 2.3 Support Unit used in test configuration ........................................................................................... 11 2.4 Measurement Results Explanation Example .................................................................................. 11 3 CONDUCTED TEST RESULT ................................................................................................................... 12 3.1 Measuring Instruments .................................................................................................................... 12 3.2 Test Setup ....................................................................................................................................... 12 3.3 Test Result of Conducted Test ........................................................................................................ 12 3.4 Conducted Output Power ................................................................................................................ 13 3.5 Peak-to-Average Ratio .................................................................................................................... 14 3.6 99% Occupied Bandwidth and 26dB Bandwidth Measurement...................................................... 15 3.7 Conducted Band Edge .................................................................................................................... 16 3.8 Conducted Spurious Emission ........................................................................................................ 17 3.9 Frequency Stability .......................................................................................................................... 18 4 RADIATED TEST ITEMS .......................................................................................................................... 19 4.1 Measuring Instruments .................................................................................................................... 19 4.2 Test Setup ....................................................................................................................................... 19 4.3 Test Result of Radiated Test ........................................................................................................... 19 4.4 Effective Radiated Power and Effective Isotropic Radiated Power Measurement ......................... 20 4.5 Field Strength of Spurious Radiation Measurement ....................................................................... 21 5 LIST OF MEASURING EQUIPMENT ........................................................................................................ 22 6 UNCERTAINTY OF EVALUATION ........................................................................................................... 23 APPENDIX A. TEST R…

Text truncated - open the document above for the full version.

SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : C1 of C2 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X FCC RF Test Report Report No. : FG5D0405 Appendix C. Setup Photographs <Radiated Emission> Y Plane for 22H LF HF SPORTON INTERNATIONAL (SHENZHEN) INC. Page Number : C2 of C2 TEL : 86-755-8637-9589 Report Issued Date : Dec. 29, 2015 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID : WVBAC622X FCC RF Test Report Report No. : FG5D0405 X Plane for 24E LF HF

SPORTON INTERNATIONAL (SHENZHEN) INC. TEL : 86-755-8637-9589 / FAX : 86-755-8637-9595 Issued Date : Dec. 29, 2015 FCC ID : WVBAC622X Page D1 of D1 Form version. : 151208 FCC SAR Test Report Report No. :FA5D0405 Appendix D. SAR Test Setup Photos Right Cheek Right Tilted Left Cheek Left Tilted Front, Test Separation 15 mm Back, Test Separation 15 mm