XCT-FM5202FM5202 Z-Wave Module

FM5202_US Z-Wave Wireless Product Instruction Manual / Label Information The device under test is manufactured by the grantee, FortrezZ, LLC, and will be sold in an array of products in the US and Canada that they will manufacture. Per 47 CFR 2.909, 2.927, 2.931, 2.1033, 15.15(b) etc..., the grantee must ensure the end-user has all applicable / appropriate operating instructions. When end-user instructions are required (as in the case of this product) the grantee must include the proper information when supplying the end product to the end-user. The following information will be included in the end product user’s manual to ensure continued FCC and Industry Canada regulatory compliance. MODULE INSTALLER ANTENNA SELECTION: Note that the FM5202-US module may only be used with (1)the Johansen712-1535-2-ND chip antenna provided, or (2)the 2.14 dBi gain monopole antenna provided, or (3)and 50 Ohm antenna of the same type, with equal or lesser gain. MODULE INSTALLER LABELING INSTRUCTIONS: The following information must be placed on your product when using the FM5202-US modular transceiver: “Contains FCC ID: XCT-FM5202, IC: 8156A-FM5202, Model: FM5202-US” THE FOLLOWING INFORMATION MUST BE PROVIDED TO THE END USER: This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Note: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment ************************************************************************************************ 1080 Centre Rd. Suite C Auburn Hills, MI 48326

Willow Run Test Labs, LLC 8501 Beck Road, Building 2227 Belleville, Michigan 48111 USA Tel: (734) 252-9785 Fax: (734) 926-9785 e-mail: [email protected] Re: Certification for FortrezZ, LLC FCC ID: XCT-FM5202 IC: 8156A-FM5202 REQUEST FOR CONFIDENTIALITY Pursuant to USA FCC 47 CRF 0.457(d) and 0.459 and Canada IC RSP-100, Section 10, FortrezZ, LLCrequests that a part of the subject application be held confidential. FortrezZ, LLC has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to ”competition” would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Exhibit Conf. TypeRational Exh 04 - Block DiagramPermanentIncludes proprietary internal oscillator frequency information. Exh 05 - SchematicsPermanentIncludes proprietary design information Exh 10 - BOM + PlacementPermanentIncludes proprietary design information Permanent Confidentiality:FortrezZ, LLC requests that any exhibits listed above as permanently confidential be permanently withheld from public review. Short-Term Confidentiality (FCC Only):FortrezZ, LLC requests that any exhibits selected above as short term confidential be withheld from public view for a period of 45 days from the date of the Grant of Equipment Authorization and prior to marketing. If there are any questions regarding the application or testing performed, please contact us at the above address or call (734) 252-9785, or e-mail [email protected]. Sincerely, Joseph D. Brunett Willow Run Test Labs, LLC 10

Page: 1 of 1 Phone: (248) 481-7092 E-Mail: [email protected] 1180 Centre Rd. Suite C Auburn Hills, MI 48326 FM5202 Wireless Module Label Location FCC and IC ID’s Silkscreened on bottom of PCB in this location. FM5202 Module Bottom View FCC ID: XCT-FM5202 IC: 8156A-FM5202 www.FortrezZ.com 10 11 8 9 7 PN: FM5202-US

Phone: (248) 481-7092 E-Mail: [email protected] 1080 Centre Rd. Suite C Auburn Hills, MI 48326 FM5202 Z-WAVE MODULE CIRCUIT DESCRIPTION The FM5202 Z-Wave module is built around the Sigma Designs ZM5202 RF transceiver module. This Sigma Designs ZM5202 contains a standard SPI serial data interface to an external data source. The data source will typically be a microcontroller which may also support the application for the product that uses the FM5202 Z-Wave module. The FM5202 Z-Wave module includes a voltage regulator which provides regulated power for the Sigma Designs ZM5202 RF transceiver module. This also extends the usable voltage range for the FM5202 Z-Wave module. The Sigma Designs ZM5202 RF transceiver module also includes a voltage regulator which provides regulated power to all of the internal circuits on the Sigma Designs ZM5202 RF transceiver module. Bypass capacitors are provided around the Sigma Designs ZM5202 RF transceiver module as needed. An external crystal at 32.000 MHz generates the clock for all of the digital circuitry on the Sigma Designs ZM5202 RF transceiver module. It also serves as a reference for the frequency synthesizer used to generate the RF carrier. This is the only clock source for the Sigma Design ZM5202. The transmitter function of the Sigma Designs ZM5202 takes the data from the external data source over the SPI interface, and creates packets per the Z-Wave protocol standard in the baseband processor. It has an RF signal source and modulator to create the 908.4MHz RF output signal. The receiver function of the Sigma Designs ZM5202 takes a signal into the Sigma Designs ZM5202 and performs a down conversion to base band where the data is taken out of the incoming packets and passed to the external data unit over the SPI interface. At the RF interface to the Sigma Designs ZM5202 an external ceramic filter is provided to reduce harmonics and to match the impedance to the antenna. The antenna is a combination of ceramic filter and printed pattern on the module printed circuit board. An integrated shield is built into the four-layer PCB. The second layer is a contiguous ground plane to ensure that it does not have to rely upon the shielding provided by the device into which it is installed in order for all modular transmitter emissions to comply with Part 15 limits. It is also intended to prevent coupling between the RF circuitry of the module and any wires or circuits in the device into which the module is installed.

Date of Issue: May 4, 2014Prepared For: FortrezZ, LLCTest Report No.: 20140504-01 Willow Run Test Labs, LLC 8501 Beck Road, Building 2227 Belleville, Michigan 48111 USA Tel: (734) 252-9785 Fax: (734) 926-9785 e-mail: [email protected] Testing of Electromagnetic Emissions per USA: CFR Title 47, Part 15.249 Canada: IC RSS-210/GENe are herein reported for FortrezZ, LLC FM5202-US Test Report No.: 20140504-01 Copyright c ©2014 Applicant/Provider: FortrezZ, LLC 520 Aarons Way, Ortonville Michigan 48462 USA Phone: +1 (248) 481-7092, Fax: +1 (248) 481-7092 Contact Person: Stella; [email protected] Measured by: Report Approved by: Dr. Joseph Brunett, EMC-002790-NEDr. Joseph Brunett, EMC-002790-NE Report by:Report Date of Issue:May 4, 2014 Dr. Joseph Brunett, EMC-002790-NE Results of testing completed on (or before) May 4, 2014 are as follows. Emissions:The transmitter intentional emissionsCOMPLYwith the regulatory limit(s) by no less than 2.8 dB. Transmit chain spurious harmonic emissionsCOMPLYby no less than 4.7 dB. Radiated spurious emissions asso- ciated with the receive chain of this deviceCOMPLYthe regulatory limit(s) by no less than 20 dB. Unintentional spurious emissions from digital circuitryCOMPLYwith radiated emission limit(s) by more than 14.5 dB. AC Power Line conducted emissionsCOMPLYby more than 14.6 dB. Willow Run Test Labs, LLC, 8501 Beck Road, Building 2227, Belleville, Michigan 48111 USAPage 1 of 19 Date of Issue: May 4, 2014Prepared For: FortrezZ, LLCTest Report No.: 20140504-01 Contents 1 Test Specifications, General Procedures, and Location4 1.1 Test Specification and General Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.2 Test Location and Equipment Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 2 Configuration and Identification of the Equipment Under Test6 2.1 Description and Declarations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 2.1.1EUT Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 2.1.2Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 2.1.3Variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2.1.4Test Samples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2.1.5Functional Exerciser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2.1.6Modifications Made . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2.1.7Production Intent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2.1.8Declared Exemptions and Additional Product Notes . . . . . . . . . . . . . . . . . . . . . . . .7 3 Emissions8 3.1 General Test Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 3.1.1Radiated Test Setup and Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 3.1.2Conducted Emissions Test Setup and Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.1.3Power Supply Variation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.1.4Thermal Variation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.2 Intentional Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.2.1Fundamental Emission Pulsed Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.2.2Fundamental Emission Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.2.3Fundamental Emission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 3.3 Unintentional Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3.3.1Transmit Chain Spurious Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3.3.2Radiated Receiver Spurious . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3.3.3Radiated Digital Spurious . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3.3.4Conducted Emissions Test Results - AC Power Port(s) . . . . . . . . . . . . . . . . . . . . . . . 19 List of Tables 1Willow Run Test Labs, LLC Equipment List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 2EUT Declarations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 3Pulsed Emission Characteristics (Duty Cycle). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4Intentional Emission Bandwidth.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5Fundamental Radiated Emissions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6Transmit Chain Spurious Emissions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 7Receiver Chain Spurious Emissions≥30 MHz.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 8Radiated Digital Spurious Emissions.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 9AC Mains Power Conducted Emissions Results.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 List of Figures 1Photos of EUT.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 2EUT Test Configuration Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 3Radiated Emissions Diagram of the EUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 4Radiated Emissions Test Setup Photograph(s). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 5Conducted Emissions Setup Diagram of the EUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . …

Text truncated - open the document above for the full version.