XEQJSR-4300RF Remote Controller

0 N O 1 2 3 Model . JSR - 4300 RF REMOTE CONTROLLER 1 3V Operationg Voltage SPECIFICATION Curtain Motor RF Receiver HOW TO ERASE SET-UP CHANNEL HOW TO SET-UP Operationg Distance Within 1km Operationg Frequency 447.775 MHz or 433.92 MHz Radio Wave type Wireless Standard F10 Communication System Wireless device for wireless minimal output 1 Way RF 1 2 3 0 N O Curtain motor : Put 1st terminal of DIP switch to "ON". The LED of the curtain motor blinks when you do this. Receiver : If you release PROG button after pressing it for 2 seconds, the Red LED blinks. 1. Set installed curtain motor or receiver to Set-Up mode 2. Select desired any channel by button. The number of the desired channel is indicated by LED Light comes ‘ON’ 3. Press PROG Button on the back of Controller for 2 seconds. 1. Turn NO.1 dip S/W to ‘on’, right side, LED in motor blinks. 4. If Remote Controller complete Set-Up correctly, the buzzer sound once. Curtain Motor : Buzzer sounds once RF Receiver : Red LED Light comes ‘ON’ 5. Turn the 1st terminal of the DIP switch to "OFF". Then, if the LED of the curtain motor lights ‘ON’. The Remote controller Set-Up is finished. 6. Set the rest of the channels in the same way. RF Remote Controller retains the last selected channel. Each Set-Up channel is memorized for collective control without additional Set-Up Procedure. 2. After selecting the applied channel, press PROG button for 2 seconds. If erasing completes correctly, the buzzer sounds two times from motor and controller. 1. Red LED Light comes off when you press PROG button for 2 seconds and take off. 2. Press PROG button for 2 seconds after selecting the applied channel. If erasing completes correctly, the buzzer sounds two times from Romote controller & Red LED L ight comes off. ( Caution : If there are remained Set-Up channel in Remote Controller, Red LED Light keeps ‘ON’)

FCC Confidential Authorization December 14, 2009 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: XEQJSR-4300 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Junshade Co., Ltd. hereby requests long-term confidential treatment of information accompanying this application as outlined below: • Block Diagram • Schematics • Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Jun Ik Park/ President 82-2-323-8181 Seowoo Bd., 395-7, Seogyo-Dong, Mapo-Gu, Seoul, Korea

BACL-NF0028-A DECLARATION OF SIMILARITY December 16, 2009 To: Bay Area Compliance Laboratories Corp. 1274 Anvilwood Ave. Sunnyvale, CA 94089 Phone: 408-732-9162, Fax: 408-732-9164 http://www.baclcorp.com Dear Sir or Madam: We, Junshade Co., Ltd. hereby declare that product: RF Remote Controller: JSR-4300(1 ch) and JSR-4300(4 ch) are electrically identical with the same electromagnetic emissions and electromagnetic compatibility characteristics as model: JSR-4300(4ch) tested by BACL, the results of which are featured in BACL project: BACL Project Number. R0904154. A description of the differences between the tested model and those that are declared similar are as follows: Only the outlook of the two devices are the difference with same model number: JSR-4300 Please contact me should there be need for any additional clarification or information. Best Regards, Jun Ik Park/ President 82-2-323-8181 Seowoo Bd., 395-7, Seogyo-Dong, Mapo-Gu, Seoul, Korea

Junshade Co., Ltd. FCC ID: XEQJSR-4300 Report R0904154-231 Page 21 of 25 FCC Part 15.231 Test Report 10 EXHIBIT C - EUT PHOTOGRAPHS 10.1 EUT - Front View (1 CH) 10.2 EUT - Rear View (1 CH) Junshade Co., Ltd. FCC ID: XEQJSR-4300 Report R0904154-231 Page 22 of 25 FCC Part 15.231 Test Report 10.3 EUT - Front View (4 CH) 10.4 EUT - Rear View (4 CH)

Junshade Co., Ltd. FCC ID: XEQJSR-4300 Report R0904154-231 Page 18 of 25 FCC Part 15.231 Test Report 8 EXHIBIT A – FCC PRODUCT LABELING REQUIREMENTS 8.1 FCC ID Label Requirements As per FCC §2.925, (a) Each equipment covered in an application for equipment authorization shall bear a nameplate or label listing the following: (1) FCC Identifier consisting of the two elements in the exact order specified in §2.926. The FCC Identifier shall be preceded by the term FCC ID in capital letters on a single line, and shall be of a type size large enough to be legible without the aid of magnification. Example: FCC ID: XXX123. Where: XXX—Grantee Code 123—Equipment Product Code As per FCC §15.19, (a) In addition to the requirements in part 2 of this chapter, a device subject to certification, or verification shall be labeled as follows: (3) All other devices shall bear the following statement in a conspicuous location on the device: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (4) Where a device is constructed in two or more sections connected by wires and marketed together, the statement specified above is required to be affixed only to the main control unit. If the EUT is integrated within another device then a label affixed to the host shall also state, “Contains FCC ID: XXXXXX” (5) When the device is so small or for such use that it is not practicable to place the statement specified under paragraph (a) of this section on it, the information required by this paragraph shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. However, the FCC identifier or the unique identifier, as appropriate, must be displayed on the device. 8.2 FCC ID Label Content Suggested additional label content As per FCC §15.19 (b) (4), the label shall not be a stick-on, paper label. The label on these products shall be permanently affixed to the product and shall be readily visible to the purchaser at the time of purchase, as described in Section 2.925(d) of this chapter. "Permanently affixed" means that the label is etched, engraved, stamped, silk-screened, indelibly printed, or otherwise permanently marked on a permanently attached part of the equipment or on a nameplate of metal, plastic, or other material fastened to the equipment by welding, riveting, or a permanent adhesive. The label must be designed to last the expected lifetime of the equipment in the environment in which the equipment may be operated and must not be readily detachable. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Manufacturer: Junshade Co., Ltd. FCC ID: XEQJSR-4300 Junshade Co., Ltd. FCC ID: XEQJSR-4300 Report R0904154-231 Page 19 of 25 FCC Part 15.231 Test Report 8.3 FCC ID Label Location Label here

Junshade Co., Ltd. FCC ID: XEQJSR-4300 Report R0904154-231 Page 23 of 25 FCC Part 15.231 Test Report 10.5 EUT – Cover off View (1 CH) 10.6 EUT – Cover off View (4 CH) Junshade Co., Ltd. FCC ID: XEQJSR-4300 Report R0904154-231 Page 24 of 25 FCC Part 15.231 Test Report 10.7 EUT – Main Board Front View 10.8 EUT – Main Board Rear View

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, NIST, or any agency of the Federal Government. * This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “*” FCC PART 15.231 TEST AND MEASUREMENT REPORT For JUNSHADE CO., LTD. 3F, Seowoo Bldg., 395-7, Seogyo-Dong,Seoul, Korea FCC ID: XEQJSR-4300 Report Type: Original Report Product Type: Remote Controller Test Engineer: Jack Liu Jerry Wang Report Number: R0904154-231 Report Date: 2009-12-21 Reviewed By: Boni Baniqued EMC/RF Supervisor Prepared By: (84) Bay Area Compliance Laboratories Corp. 1274 Anvilwood Ave. Sunnyvale, CA 94089, USA Tel: (408) 732-9162 Fax: (408) 732-9164 Junshade Co., Ltd. FCC ID: XEQJSR-4300 Report R0904154-231 Page 2 of 25 FCC Part 15.231 Test Report TABLE OF CONTENTS 1 GENERAL INFORMATION.............................................................................................................................. 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................................... 4 1.2 MECHANICAL DESCRIPTION........................................................................................................................... 4 1.3 EUT PHOTO.................................................................................................................................................... 4 1.4 OBJECTIVE...................................................................................................................................................... 4 1.5 RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................... 5 1.6 TEST METHODOLOGY..................................................................................................................................... 5 1.7 TEST FACILITY............................................................................................................................................... 5 2 SYSTEM TEST CONFIGURATION ................................................................................................................. 6 2.1 JUSTIFICATION................................................................................................................................................ 6 2.2 EUT EXERCISE SOFTWARE............................................................................................................................. 6 2.3 SPECIAL ACCESSORIES................................................................................................................................... 6 2.4 EQUIPMENT MODIFICATIONS.......................................................................................................................... 6 2.5 SPECIAL EQUIPMENT...................................................................................................................................... 6 2.6 LOCAL SUPPORT EQUIPMENT......................................................................................................................... 6 2.7 EUT INTERNAL CONFIGURATION DETAILS..................................................................................................... 6 2.8 EXTERNAL I/O CABLING LIST AND DETAILS.................................................................................................. 6 3 SUMMARY OF TEST RESULTS ...................................................................................................................... 7 4 FCC §15.205, §15.209 & §15.231(B) - RADIATED EMISSIONS .................................................................... 8 4.1 MEASUREMENT UNCERTAINTY...................................................................................................................... 8 4.2 RADIATED EMISSIONS EUT SETUP................................................................................................................. 8 4.3 SPECTRUM ANALYZER SETUP......................................................................................................................... 8 4.4 TEST EQUIPMENT LIST AND DETAIL............................................................................................................... 8 4.5 TEST PROCEDURE........................................................................................................................................... 9 4.6 CORRECTED AMPLITUDE & MARGIN CALCULATION...................................................................................... 9 4.7 APPLICABLE STANDARD REQUIREMENT......................................................................................................... 9 4.8 TEST SETUP BLOCK DIAGRAM...................................................................................................................... 10 4.9 TEST ENVIRONMENTAL CONDITIONS............................................................................................................ 10 4.10 SUMMARY OF TEST RESULTS........................................................................................................................ 10 4.11 RADIATED EMISSIONS TEST DATA............................................................................................................... 11 5 FCC §15.231(C) – 20 DB BANDWIDTH TESTING .......................................................................................12 5.1 REQUIREMENT.............................................................................................................................................. 12 5.2 TEST EQUIPMENT LIST AND DETAILS..................................................................................................…

Text truncated - open the document above for the full version.

Junshade Co., Ltd. FCC ID: XEQJSR-4300 Report R0904154-231 Page 20 of 25 FCC Part 15.231 Test Report 9 EXHIBIT B - TEST SETUP PHOTOGRAPHS 9.1 Radiated Emissions - Front View 9.2 Radiated Emissions - Rear View