XJ4KB6138BLUETOOTH KEYBOARD

Welcome to use the Bluetooth wireless keyboard Product structure diagram 12 12 34 5 1-----Charge 2-----Power switch 3-----Charging light 4-----Lamp of code 5-----Link button illustrate: KB-6138 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. Replaceable batteries If an equipment is provided with a replaceable battery, and if replacement by an incorrect type could result an explosion(for example, with some lithium batteries), the following applies: -if the battery is placed in an OPERATOR ACCESS AREA, there shall be a marking close to the battery or a statement in both the operating and the servicing instructions; -if the battery is placed elsewhere in the equipment, there shall be a marking close to the battery or a statement in the servicing instructions. This marking or statement shall include the following or similar text: CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

CHINFAI (HK) TECHNOLOGY CO. , LIMITED Resuest, for Confidentialitv Date: ?01L11.28 Subject: Confi dentiality Request for:XJ4KB6138 Pursuant to FCC 47 CRF 0,457(d) and 0.459 and IC RSP-I00, Section 10, the applicant requests that a part of the subject FCC application be held confidential. NOTE for lndustry Canada Applications: The applicant understands that until such time Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & PlacemeffirBOM Tune-Up Procedure Schematics Test Setup Photos User's Manual between Short Term and Permanent Type of Connouiii"tity Requested f] ShortTerm ffi Permanent X Short t"r* flstrortTerm flsho*,Term I Strort term f] sho* Term flShortterm flsho*Term flshortTerm f] Permanent*z ffi Permanent f] Permanent I Permanent filPermanent f] Permanent* *Note: ' (Insert Explanation as Necessary) :'',. .: :.:.'CFIIN.F .(F{.K}ILEdFiNOIOGY€O',;IIM ED.-':: has spent substanrial effort in developing this producl and it is one of the first of its kind in industry. Having the subject information easily available to "competitien" would negate the advantage they have achieved by developing this product. Nct protecting the details of the design will result in financial hardship. Permanent Confi dentiality: The applicant requests the ;xhibits listed above as permanently confidential be permanentty withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confi dentia lity : The applicant requests the exhibits selected above as short term confidential be withheld frorn public view for a period of (specify nurnber of days n - days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public, Applicant is also aware that they are responsible to notiq ACB in the event information rega:ding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Confrdentiality, either type of marked exhibitConfidential wheir dubrnitted to IC. Sincerely By: 2 - The asterisked items (*) require further.justi confidentiality will be allowed. These also currently require review by the FCC under their Petmit-But-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted devipe would be: "The' EUT is FULLY potted using a non-removable epoxy based material. Removal of potting malerial causes irreparable damage to intemal circuitry. See photographs exhibits that outline the device before and after potting." - Please refer to http:i/acbceg,com/documentslpisc-docs/Memo-Sho*-Term-Vs-Standard-Confidentialitv.pdf for complete details- - l,tilsl be signe<l by applicarrt contact given fol applica*t cn the FCC situ rx by the a*thorizeri ager:t if :rn applopriate authorized ageni letter h*s beert prcvicle.d. Letter-c should be placed on appropdate letterhead. 022311 -6 re

1 Photographs (Test mode No.KB-6138) 1.1 EUT Constructional Details

35mm 30mm 16mm 13mm

1 Photographs (Test mode No.KB-6138) 1.1 EUT Constructional Details

SGS-CSTC Standards Technical Services Ltd. No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM111100469701 Page: 1 of 52 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No: SZEM1111004697RF Applicant: CHINFAI (HK) TECHNOLOGY CO., LIMITED Manufacturer: CHINFAI (HK) TECHNOLOGY CO., LIMITED Factory: CHINFAI (HK) TECHNOLOGY CO., LIMITED Product Name: BLUETOOTH KEYBOARD Model No.(EUT): KB-6138 FCC ID: XJ4KB6138 Standards: FCC CFR Title 47 Part 15 (2010) Date of Receipt: 2011-11-30 Date of Test: 2011-12-01 to 2011-12-05 Date of Issue: 2012-05-07 Test Result: PASS * . * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM111100469701 Page: 2 of 52 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Test Summary Test Item Test Requirement Test method Result Antenna Requirement FCC CFR Title 47 Part 15C Section 15.203/15.247 (c) ANSI C63.10 (2009) PASS AC Power Line Conducted Emission FCC CFR Title 47 Part 15C Section 15.207 ANSI C63.10 (2009) PASS Conducted Peak Output Power FCC CFR Title 47 Part 15C Section 15.247 (b)(1) ANSI C63.10 (2009) PASS 20dB Occupied Bandwidth FCC CFR Title 47 Part 15C Section 15.247 (a)(1) ANSI C63.10 (2009) PASS Carrier Frequencies Separation FCC CFR Title 47 Part 15C Section 15.247 (a)(1) ANSI C63.10 (2009) PASS Hopping Channel Number FCC CFR Title 47 Part 15C Section 15.247 (b) ANSI C63.10 (2009) PASS Dwell Time FCC CFR Title 47 Part 15C Section 15.247 (a)(1) ANSI C63.10 (2009) PASS Pseudorandom Frequency Hopping Sequence FCC CFR Title 47 Part 15C Section 15.247(b)(4)&TCB Exclusion List (7 July 2002) ANSI C63.10 (2009) PASS Band-edge for RF Conducted Emissions FCC CFR Title 47 Part 15C Section 15.247(d) ANSI C63.10 (2009) PASS RF Conducted Spurious Emissions FCC CFR Title 47 Part 15C Section 15.247(d) ANSI C63.10 (2009) PASS Radiated Spurious emissions FCC CFR Title 47 Part 15C Section 15.205/15.209 ANSI C63.10 (2009) PASS Band Edge (Radiated Emission) FCC CFR Title 47 Part 15C Section 15.205/15.209 ANSI C63.10 (2009) PASS SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM111100469701 Page: 3 of 52 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnificati…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Nanshan District, Shenzhen, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM111100469703 Page: 1 of 5 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover Page Cover PageCover Page Cover Page SAR Evaluation Report Application No.: SZEM1111004697RF Applicant: CHINFAI (HK) TECHNOLOGY CO., LIMITED Manufacturer: CHINFAI (HK) TECHNOLOGY CO., LIMITED Factory CHINFAI (HK) TECHNOLOGY CO., LIMITED Product Name: BLUETOOTH KEYBOARD Model No.(EUT): KB-6138 Standard: FCC CFR Title 47 Part 1.1307 FCC CFR Title 47 Part 2.1093 KDB447498D01 FCC ID: XJ4KB6138 Date of Receipt: 2011-11-30 Date of Test: 2011-12-01 to 2011-12-05 Date of Issue: 2012-05-07 Test Result: PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM111100469703 Page: 2 of 5 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Contents 1 COVER PAGE ...............................................................................................................................................1 2 CONTENTS ................................................................................................................................................... 2 3 GENERAL INFORMATION ........................................................................................................................... 3 3.1 CLIENT INFORMATION.............................................................................................................................. 3 3.2 GENERAL DESCRIPTION OF EUT.............................................................................................................. 3 3.3 TEST LOCATION...................................................................................................................................... 3 3.4 TEST FACILITY........................................................................................................................................ 4 3.5 DEVIATION FROM STANDARDS.................................................................................................................. 4 3.6 ABNORMALITIES FROM STANDARD CONDITIONS........................................................................................ 4 3.7 OTHER INFORMATION REQUESTED BY THE CUSTOMER.............................................................................. 4 4 SAR EVALUATION ....................................................................................................................................... 5 4.1 RF EXPOSURE COMPLIA…

Text truncated - open the document above for the full version.

1 Photographs (Test mode No.KB-6138) 1.1 Conducted Emission Test Setup 1.2 Radiated Emission Test Setup