XO8-FSBLE-ABLE Fall Sensor

Fall Sensor – FSBLE-A This Fall Sensor is device designed with a push button that allows the user to call for help at any time. It can also automatically 1 activate an emergency alarm if it detects a fall in the event that the user is unable to trigger an alarm by pressing the button. A. Usage Recommendation 1. For best results, the Fall Sensor should rest at the center of the user’s breastbone 2. Wear the Fall Sensor on the outside of all articles of clothing. 3. Carefully place the Fall Sensor on a table or nightstand when you are not using it in order to avoid activating an alarm. 4. The Fall Sensor may be worn in the shower (IP45). B. Identifying the Parts 1. Emergency Button Pressing the Emergency Button for 0.5 sec will activate the Control Panel, causing it to dial an emergency call or alarm (CID event code: 101). 2. LED 3. Lanyard The lanyard length is adjustable. 4. Battery Compartment Cover 1. When replacing the battery, ensure that the positive side (+) of the battery is facing outward. 2. After replacing the battery, press and hold the Emergency Button until you see the LED flash RED then GREEN. 3. When replacing the battery, it is recommended to press the Fall Sensor button and run a test of your equipment. NOTE: Contact your authorized dealer for additional assistance. 1 Note: Fall Sensors do not detect 100% of falls. If you are able to do so, you should always press the button if you need help. LED Off Standby Mode 1 Red Flash Replacement Battery Inserted 1 Red, then 1 Green Flash First button press after replacing battery 1 Green Flash Transmitting with Good Battery 1 Red Flash Transmitting with Low Battery FCC ID: XO8-FSBLE-A rev. A01 C. Low Battery Detection and Supervision Fall Sensor features Auto Low Battery detection and Supervision. When a battery is below the low battery threshold, the Fall Sensor will automatically send a low battery supervisory message every two hours. D. Testing When testing, do not activate the Fall Sensor twice within a 10-second interval. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance may void the user's authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.

Instant Care, Inc.. 2080 Wineridge Pl.Suite A, Escondido, California, United States, 92029 Date: November 13, 2020 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: XO8-FSBLE-A To whom it may concern: We, the undersigned, hereby authorize Ms. Daphne Liang / Section Manager of SGS Compliance Certification Services Inc. to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with << Instant Care, Inc. >>. This authorization is valid until further written notice from the applicant. Name (Printed): Richard Darling Title: CEO Signature: On behalf of Company: Instant Care, Inc.. Telephone: (877)424-4050

Instant Care, Inc.. 2080 Wineridge Pl.Suite A, Escondido, California, United States, 92029 To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Instant Care, Inc. 9750 Birch Canyon Place San Diego, CA 92126 United States Regarding: Confidentiality Request regarding application for FCC ID: XO8-FSBLE-A LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Richard Darling CEO Instant Care, Inc.

Page 1 / 5 Report No.: T201028N02 Ref. No.: Rev. 00 External Photo (Model: FSBLE-A )

FSBLE-A Diagram Label location Label location Model: FSBLE-A FCC ID：XO8-FSBLE-A

Page 2 / 5 Report No.: T201028N02 Ref. No.: Rev. 00 Internal Photo (Model: FSBLE-A ) Page 3 / 5 Report No.: T201028N02 Ref. No.: Rev. 00 Page 4 / 5 Report No.: T201028N02 Ref. No.: Rev. 00 Page 5 / 5 Report No.: T201028N02 Ref. No.: Rev. 00

FCC ID: XO8-FSBLE-A Page: 1 / 59 Report No.: T201028N02-RP1 Rev.: 04 No.8, Jiucengling, Xinhua Dist., Tainan City, Taiwan /台南市新化區礁坑里九層嶺8號 t:(886-6) 5802-201 f:(886-6) 5802-202 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group FCC 47 CFR PART 15 SUBPART C AND ANSI C63.10: 2013 TEST REPORT For BLE Fall Sensor Model: FSBLE-A Brand: Issued for Instant Care, Inc. 2080 Wineridge Pl.Suite A,Escondido,California,United States, Issued by Compliance Certification Services Inc. Tainan Lab. No.8, Jiucengling, Xinhua Dist., Tainan City, Taiwan Issued Date: November 24, 2020 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. Ltd. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document Page: 2 / 59 Report No.: T201028N02-RP1 Ref. No.: Rev.: 04 REVISION HISTORY Rev. Issue Date Revisions Effect Page Revised By 00 November 16, 2020 Initial Issue ALL Polly Wang 01 November 18, 2020 See the following note rev.01 P.43.46-48 Polly Wang 02 November 19, 2020 See the following note rev.02 P.43.46-48 Polly Wang 03 November 20, 2020 See the following note rev.03 P.43.46-48 Polly Wang 04 November 24, 2020 See the following note rev.04 P.26.43.46-48 Polly Wang Note: ※ Rev.00 Issue Date: November 16, 2020 Original Report. ※ Rev.01 Issue Date: November 18, 2020 Update the note on page 43. Update the remark on page 46-48. ※ Rev.02 Issue Date: November 19, 2020 Update the note on page 43. Update the remark on page 46-48. ※ Rev.03 Issue Date: November 20, 2020 Update the note on page 43. Update the remark on pa ge 46-48. ※ Rev.04 Issue Date: November 24, 2020 Update duty cycle data and the note on page 43, the remark on page 46-48. Page: 3 / 59 Report No.: T201028N02-RP1 Ref. No.: Rev.: 04 TABLE OF CONTENTS 1. TEST REPORT CERTIFICATION ............................................................................... 4 2. TEST RESULT SUMMARY ......................................................................................... 5 3. EUT DESCRIPTION ..................................................................................................... 6 3.1 DESCRIPTION OF EUT & POWER ...................................................................................... 6 4. DESCRIPTION OF TEST MODES ............................................................................... 7 5. TEST METHODOLOGY ............................................................................................... 8 6. FACILITIES AND ACCREDITATIONS ........................................................................ 8 6.1 FACILITIES ............................................................................................................................ 8 6.2 EQUIPMENT .......................................................................................................................... 8 6.3 LABORATORY ACCREDITATIONS LISTINGS .................................................................... 8 6.4 TABLE OF ACCREDITATIONS AND LISTINGS ................................................................... 9 7. CALIBRATION AND UNCERTAINTY ....................................................................... 10 7.1 MEASURING INSTRUMENT CALIBRATION ...................................................................... 11 7.2 MEASUREMENT UNCERTAINTY ....................................................................................... 11 8. SETUP OF EQUIPMENT UNDER TEST ................................................................... 12 8.1 SETUP CONFIGURATION OF EUT .................................................................................... 12 8.2 SUPPORT EQUIPMENT ..................................................................................................... 13 8.3 EUT OPERATING CONDITION ........................................................................................... 14 9. APPLICABLE LIMITS AND TEST RESULTS ........................................................... 15 9.1 6dB BANDWIDTH ................................................................................................................ 15 9.2 MAXIMUM PEAK OUTPUT POWER ................................................................................... 19 9.3 DUTY CYCLE ...................................................................................................................... 25 9.4 POWER SPECTRAL DENSITY ........................................................................................... 29 9.5 CONDUCTED SPURIOUS EMISSION .…

Text truncated - open the document above for the full version.

Page: 1 / 1 Report No.: T201028N02-MF Rev.: 00 No.8, Jiucengling, Xinhua Dist., Tainan City, Taiwan /8 t:(886-6) 5802-201 f:(886-6) 5802-202 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. Member of the SGS Group According to KDB 447498 section 4.3.1, the 1-g SAR test exclusion thresholds at test separation distance ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] *·[f(GHz)] ≤ 3.0 The tune-up power is -9.00 dBm +/- 0.5dB, therefore the highest tune-up power is -8.50 dBm (0.14 mW) @ 2442 MHz When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. So, ( (0.14 mW) / 5mm ) * ( 2.442GHz ^0.5 )= 0.04 [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] * [f(GHz)] = 0.9 < 3.0 Therefore, standalone SAR measurements are not required for both head and body.

Page: 56 / 59 Report No.: T201028N02-RP1 Ref. No.: Rev.: 04 APPENDIX I SETUP PHOTOS RADIATED EMISSION MEASUREMENT SETUP Below 1GHz Page: 57 / 59 Report No.: T201028N02-RP1 Ref. No.: Rev.: 04 Page: 58 / 59 Report No.: T201028N02-RP1 Ref. No.: Rev.: 04 RADIATED RF MEASUREMENT SETUP Above 1GHz Page: 59 / 59 Report No.: T201028N02-RP1 Ref. No.: Rev.: 04 RF CONDUCTED SETUP