XO8-HALOBLETXHalo Transmitter

FCC ID: XO8-HALOBLETX rev. 001 Instant Care Halo Transmitter Model #: HALOBLETX-1 • Identifying the Parts 1 1. Emergency Button/ LED • Learning-in the Halo Transmitter Press the Emergency button, a Bluetooth Low Energy signal will be transmitted to the Control Panel. Please refer to the learn-in procedure of your Control Panel for further instruction. • Operation  To dial Emergency Line: Press once on the Emergency button, the GREEN LED will illuminate briefly and transmit the message to the Control Panel. • Battery & Electrical Specifications  Frequency: 2.45 GHz  Battery: CR2032, 3V 230mAh  Battery life: Approximately 3 years  Open Field Range: Approximately 5.  Low battery status: when the battery voltage is below the threshold, the Halo Transmitter will indicate a low battery by illuminating the RED LED for .5 seconds when the Emergency button is pressed. The low battery signal will be transmitted to the Control Panel. A supervisory message will be sent during a low battery state. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Caution To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance may void the user’s authority to operate his equipment. (Example – use only shielded interface cables when connecting to computer or peripheral devices) This device must not be co-located or operated in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. FCC Section 15.105 Information to the user. NOTE: This equipment has been tested and found to comply with the limits for a lass B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Instant Care, Inc. Address 2080 Wineridge Pl.Suite A,Escondido,California,United States, 92029 Grantee Code XO8 FCC ID XO8-HALOBLETX Authorized Contact Name Richard Darling Contact Email [email protected] Contact Phone 877-424-4050 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date: 05/22/20 Print Name: Richard Darling Title: CEO *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States

Instant Care, Inc.. 2080 Wineridge Pl.Suite A, Escondido, California, United States, 92029 Date: May 8, 2020 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: XO8-HALOBLETX To whom it may concern: We, the undersigned, hereby authorize Ms. Daphne Liang / Section Manager of SGS Compliance Certification Services Inc. to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with << Instant Care, Inc. >>. This authorization is valid until further written notice from the applicant. Name (Printed): Richard Darling Title: CEO Signature: On behalf of Company: Instant Care, Inc.. Telephone: (877)424-4050

Instant Care, Inc.. 2080 Wineridge Pl.Suite A, Escondido, California, United States, 92029 To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Instant Care, Inc. 9750 Birch Canyon Place San Diego, CA 92126 United States Regarding: Confidentiality Request regarding application for FCC ID: XO8-HALOBLETX LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. .

Page 1 / 4 Report No.: T200508N03 Ref. No.: Rev. 00 External Photo (Model: HALOBLETX-1)

HALOBLETX-1 Diagram Label location Label location Model: HALOBLETX-1 FCC ID ：XO8-HALOBLETX

Page 2 / 4 Report No.: T200508N03 Ref. No.: Rev. 00 Internal Photo (Model: HALOBLETX-1) Page 3 / 4 Report No.: T200508N03 Ref. No.: Rev. 00 Page 4 / 4 Report No.: T200508N03 Ref. No.: Rev. 00

FCC ID: XO8-HALOBLETX Page: 1 / 7 Report No.: T200508N03-MF Rev.: 00 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group IEEE C95.1 KDB 447498 D03 47 C.F.R. Part 1, Subpart I, Section 1.1310 47 C.F.R. Part 2, Subpart J, Section 2.1091 RF EXPOSURE REPORT For Halo Transmitter Model: HALOBLETX-1 Data Applies To: N/A Trade Name: Issued to Instant Care, Inc. 2080 Wineridge Pl.Suite A,Escondido,California,United States, 92029 Issued By Compliance Certification Services Inc. Wugu Lab. No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan Issued Date: May 28, 2020 Page: 2 / 7 Report No.: T200508N03-MF Ref. No.: Rev.: 00 REVISION HISTORY Rev. Issue Date Revisions Effect Page Revised By 00 May 28, 2020 Initial Issue ALL Angel Cheng 01 February 20, 2020 See the following note rev.01 ALL Angel Cheng Note: ※ Rev.00 Issue Date: February 10, 2020 Original Report ※ Rev.01 Issue Date: February 20, 2020 Revise EUT Specification & Maximum Permissible Exposure. Page: 3 / 7 Report No.: T200508N03-MF Ref. No.: Rev.: 00 TABLE OF CONTENTS 1. LIMIT .......................................................................................................................................... 4 2. EUT SPECIFICATION ....................................................................................................... 5 3. TEST RESULTS ................................................................................................................... 6 4. MAXIMUM PERMISSIBLE EXPOSURE ................................................................... 7 Page: 4 / 7 Report No.: T200508N03-MF Ref. No.: Rev.: 00 1. TEST RESULT CERTIFICATION We hereby certify that: The equipment has been tested by Compliance Certification Services Inc., and found compliance with the requirement of the applicable standards. The test record, data evaluation and Equipment under Test (EUT) configurations represented herein are true and accurate accounts of the measurement of the sample’s RF characteristics under the conditions specified in this report. APPLICABLE STANDARDS STANDARD TEST RESULT IEEE C95.1 2005 KDB 447498 D03 47 C.F.R. Part 1, Subpart I, Section 1.1310 47 C.F.R. Part 2, Subpart J, Section 2.1091 No non-compliance noted Statements of Conformity Determining compliance shall be based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. Approved by: Kevin Tsai Deputy Manager Compliance Certification Services Inc. Page: 5 / 7 Report No.: T200508N03-MF Ref. No.: Rev.: 00 2. LIMIT According to §15.247(i), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission's guidelines. See § 1.1307(b)(1) of this chapter. 3. EUT SPECIFICATION EUT Halo Transmitter Model HALOBLETX-1 Brand RF Module NORDIC Model: NRF52832 Frequency band (Operating) 802.11b/g/n HT20: 2412MHz ~ 2462MHz 802.11n HT40: 2422MHz ~ 2452MHz Others 2402MHz ~ 2480MHz (BT 5.2) Device category Portable (<20cm separation) Mobile (>20cm separation) Others Exposure classification Occupational/Controlled exposure (S = 5mW/cm 2 ) General Population/Uncontrolled exposure (S=1mW/cm 2 ) Antenna Specification Multilayer Chip Antenna / Gain: 3.3 dBi (Numeric gain: 2.14) worst Maximum Output power GFSK(5.2) -0.11 dBm (0.975 mW) Maximum Average output power GFSK(5.2) -0.42 dBm (0.908 mW) Maximum Tune up Power GFSK(5.2) 0.50 dBm (1.122 mW) Evaluation applied MPE Evaluation* SAR Evaluation N/A Reported Date May 27, 2020 Page: 6 / 7 Report No.: T200508N03-MF Ref. No.: Rev.: 00 4. TEST RESULTS No non-compliance noted. Calculation Given d GP E  = 30 & 377 2 E S= Where E = Field strength in Volts / meter P = Power in Watts G = Numeric antenna gain d = Distance in meters S = Power density in milliwatts / square centimeter Combining equations and re-arranging the terms to express the distance as a function of the remaining variables yields: 2 377 30 d GP S  = Changing to units of mW and cm, using: P (mW) = P (W) / 1000 and d (cm) = d(m) / 100 Yields () () 22 0796.0 100/377 1000/30 d GP d GP S  =   = Equation 1 Where d = Distance in cm P = Power in mW G = Numeric antenna gain S = Power density in mW / cm 2 Page: 7 / 7 Report No.: T200508N03-MF Ref. No.: Rev.: 00 5. MAXIMUM PERMISSIBLE EXPOSURE Substituting the MPE safe distance using d = 20 cm into Equation 1: GPS=000199.0 Where P = Power in mW G = Numeric antenna gain S = Power density in mW / cm 2 GFSK(5.2)…

Text truncated - open the document above for the full version.

FCC ID: XO8-HALOBLETX Page: 1 / 59 Report No.: T200508N03-RP1 Rev.: 00 No.8, Jiucengling, Xinhua Dist., Tainan City, Taiwan /8 t:(886-6) 5802-201 f:(886-6) 5802-202 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. Member of the SGS Group FCC 47 CFR PART 15 SUBPART C AND ANSI C63.10: 2013 TEST REPORT For Halo Transmitter Model: HALOBLETX-1 Brand: Issued for Instant Care, Inc. 2080 Wineridge Pl.Suite A,Escondido,California,United States, Issued by Compliance Certification Services Inc. Tainan Lab. No.8, Jiucengling, Xinhua Dist., Tainan City, Taiwan Issued Date: May 25, 2020 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. Ltd. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document Page: 2 / 59 Report No.: T200508N03-RP1 Ref. No.: Rev.: 00 REVISION HISTORY Rev. Issue Date Revisions Effect Page Revised By 00 May 25, 2020 Initial Issue ALL Polly Wang 01 February 25, 2020 See the following note rev.01 ALL Gina Lin 02 February 26, 2020 See the following note rev.02 Page10 Gina Lin Note: Rev.00 Issue Date: February 13, 2020 Original Report Rev.01 Issue Date: February 25, 2020 Revise typo & Measurement Equipment & Average Power & Test Procedure. Rev.02 Issue Date: February 26, 2020 Revise Measurement Equipment. Page: 3 / 59 Report No.: T200508N03-RP1 Ref. No.: Rev.: 00 TABLE OF CONTENTS 1. TEST REPORT CERTIFICATION................................................................................ 4 2. TEST RESULT SUMMARY ......................................................................................... 5 3. EUT DESCRIPTION ..................................................................................................... 6 3.1 DESCRIPTION OF EUT & POWER ...................................................................................... 6 4. DESCRIPTION OF TEST MODES ............................................................................... 7 5. TEST METHODOLOGY ............................................................................................... 8 6. FACILITIES AND ACCREDITATIONS ........................................................................ 8 6.1 FACILITIES ............................................................................................................................ 8 6.2 EQUIPMENT .......................................................................................................................... 8 6.3 LABORATORY ACCREDITATIONS LISTINGS .................................................................... 8 6.4 TABLE OF ACCREDITATIONS AND LISTINGS ................................................................... 9 7. CALIBRATION AND UNCERTAINTY ....................................................................... 10 7.1 MEASURING INSTRUMENT CALIBRATION ...................................................................... 11 7.2 MEASUREMENT UNCERTAINTY ....................................................................................... 11 8. SETUP OF EQUIPMENT UNDER TEST ................................................................... 12 8.1 SETUP CONFIGURATION OF EUT .................................................................................... 12 8.2 SUPPORT EQUIPMENT ..................................................................................................... 13 8.3 EUT OPERATING CONDITION ........................................................................................... 14 9. APPLICABLE LIMITS AND TEST RESULTS ........................................................... 15 9.1 6dB BANDWIDTH ................................................................................................................ 15 9.2 MAXIMUM PEAK OUTPUT POWER ................................................................................... 19 9.3 DUTY CYCLE ...................................................................................................................... 25 9.4 POWER SPECTRAL DENSITY ........................................................................................... 29 9.5 CONDUCTED SPURIOUS EMISSION ................................................................................ 33 9.6 RADIATED EMISSIONS ...................................................................................................... 39 9.7 POWERLINE CONDUCTED EMISSIONS ........................................................................... 53 10. ANTENNA REQUIREMENT .................................................................................... 55 10.1 STANDARD APPLICABLE ...........................…

Text truncated - open the document above for the full version.

Page: 56 / 59 Report No.: T200508N03-RP1 Ref. No.: Rev.: 00 APPENDIX I SETUP PHOTOS RADIATED EMISSION MEASUREMENT SETUP Below 1GHz Page: 57 / 59 Report No.: T200508N03-RP1 Ref. No.: Rev.: 00 Page: 58 / 59 Report No.: T200508N03-RP1 Ref. No.: Rev.: 00 RADIATED RF MEASUREMENT SETUP Above 1GHz Page: 59 / 59 Report No.: T200508N03-RP1 Ref. No.: Rev.: 00 RF CONDUCTED SETUP