XSFPS33032PS3 Controller

Product name： ：： ：PS3/PC 2IN1 Wireless controller .Fuction describtion .Fuction describtion.Fuction describtion .Fuction describtion 1.This product is designed for PS3 game console. .Features .Features.Features .Features PS3/PC 2 in 1 wirless controller is for use with PS3/PC.This product adopts the advanced sensing motion technology. .Technical data .Technical data.Technical data .Technical data 1. 2.4GHZ wireless controller. 2. USB Charging. 3. Compatible PS3 any version. 4. Support dual vibration. 5. 6 axis sensing motion. 6. Forced connection and seven channels LED indication. 7. △ ○ X □ L1 R1 L2 R2 SELECT START L3 R3 PS button. 8. Overall size：L133 ×85 W×H47 MM .How to use it? .How to use it?.How to use it? .How to use it? 1.Correctly connect PS3 console and TV,plug the controller receiver into the PS3 console USB port,then turn on console. 正确连接好主机电源及电视机，将手柄接 收器插入PS3主机USB口,并开启主机电源; Here the LED on controller receiver starts to flash slowly indicating it's ready for connection. 2.Install battery pack or place AA batteries to the battery compartment, turn the controller switch to ON posistion,the channel indicator on controller starts to flash slowly.装入电池盒或电池包，打开手柄电源开关,手柄上的通道指示灯 开始闪烁(慢闪)，此时先按一下接 Press Link button on receiver and press PS button on controller.The LED on both receiver and controller will be illuminated indicating the connection is Once they're connected successfully, it's ok to just press PS button for connection on next time. 3、The controller PS button is same with the original controller PS button. 4、Channel combination: LED1-4 indicates channel1-4,LED1+LED4 indicates channel 5,LED2+LED4 indicates channel6,LED3+LED4 indicates channel7. 5.The button function is same as original. (△、○、□、×,D-pad ,L1，L2， R1，R2,left 3D ,right 3D,SELECT,START ) For use with PC: 1.Plug the receiver into PC console USB port, the LED on receiver will 2. Install driver： 3.Install battery pack or place AA batteries to the battery compartment, turn the controller switch to ON posistion,the channel indicator on controller starts to flash slowly. 4. Press Link button on receiver,the LED indicator will flash quickly.Then press PS button on controller, here the LED indicator on receiver will be illuminated continuously. 5.Click to enter the test interface as below pictures. .special remark .special remark.special remark .special remark FCC ID：XSFPS33032 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment PS3/PC 2IN1 Wireless controller Instruction Manual 功能键 参数值变 化 △1 Ο2 Χ3 □4 L25 R26 L17 R18 SELECT 9 START 10 L311 R312 PS13 UP 14 POV 上 RIGHT 15 POV 右 DOWN 16 POV 下 LEFT 17 POV 左 127/0 127/0127/0 127/0 255/127 255/127255/127 255/127 0/127 0/1270/127 0/127 127/255 127/255127/255 127/255 左 左左 左3 33 3D DD D 右 右右 右3 33 3D DD D 127/127 左马达 左马达左马达 左马达 右马达 右马达右马达 右马达 按下图动动方向测试各SENSOR的性能， 上下都必须测试通过。上下红色“X” 的位置，都必须变为绿色：√ 黄色代表 黄色代表黄色代表 黄色代表X XX X轴动动方向 轴动动方向 轴动动方向 轴动动方向 蓝表代表 蓝表代表蓝表代表 蓝表代表Y YY Y轴动动方向 轴动动方向 轴动动方向 轴动动方向 白色代表 白色代表白色代表 白色代表Z ZZ Z轴动动方向 轴动动方向 轴动动方向 轴动动方向 红色代表 红色代表红色代表 红色代表G GG G轴动动方向 轴动动方向 轴动动方向 轴动动方向 3.Do not use detergents to clean the product, that may damage the cabinet finish and leak inside.请不要用腐蚀性液体擦拭,避免硬物划伤机壳表面，以免影响外 4.Do not expose this product into dust,direct sunlight,wet weather environment. 请勿将本产品置于下列环境下,过热,冷或太潮湿的地方,阳光直接照射的地方,灰尘较多 的地方. 5.Do not use any cleaner and other chemical.Soft cloth is OK 机壳表面沾有污垢和 以免腐蚀机壳表面和注入机内损坏元器件. 6.Do not disassembly,that may damage product,and lose the guarantee rights.不要 尝试自行分解,拆装或改装本产品的任何部分,这样的行为可能会损坏产品,并使您所 享有的产品保修失效. 7.If you abandon the product please put it into the recycling station如果要丢弃 本产品时，请将其放入专业的回收站进行处理。 8.Please use the product following the instruction.If any technical problem,please contact our technician for assistance.请依照使用说明书进行产品组 装或调整，请不要自行以非本手册说明范围内的方式或程序 调整，如果您以非本说明书的方式和程序调整发生不可预期的状况，请您通知本公司相 客服、技术人员为你处理！ 八 八八 八. .. .Special statement Special statement Special statement Special statement 特别申明 特别申明特别申明 特别申明： ：： ： 1.PS3 is registered trademark of SONY.This product is not sponsored, endorsed or approved by Sony. PS3 品牌是SONY公司的商标，本产品非SONY公司授权生产的产品。 +

Zoozen Ltd Unit 811 Cyberport RD Pok Fu Lam AUTHORIZATION LETTER To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf, as our agent, in the following matters related to the FCC approval of our product: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by SGS within the scope of this authorization shall have the same effects as our own. This authorization shall expire 6 months from original date. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you. Sincerely, Rex chang Manager

Zoozen Ltd Unit 811 Cyberport RD Pok Fu Lam Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mils Road Columbia, Maryland 21046 Subject: Permanent Confidentiality request for FCC ID: XSFPS33032 To Whom It May Concern, Pursuant to sections 0.457 and 0.459 of CFR47, the applicant requests permanent confidential treatment of the following information accompanying this application: Block Diagrams Schematics Operation Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, Rex chang Manager

“This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the …

Text truncated - open the document above for the full version.

Report No.: SZEMO09080483601 Page: 1 of 22 Authorized Signature: Robinson Lo Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” SGS-CSTC Standards Technical Services Ltd. No. 1 Workshop, M-10, Middle Section, Science & Technology Park, District Shenzhen, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] FEDERAL COMMUNICATIONS COMMISSION Registration number: 556682 TEST REPORT Application No. : SZEMO090804836TX Applicant: Zoozen Ltd Manufacturer: SHENZHEN HAIS ELECTONIC CO., LTD. FCC ID: XSFPS33032 Fundamental Carrier Frequency : 2.410GHz to 2.470GHz Equipment Under Test (EUT): Name: PS3 Controller Model: HS-P-3032 Standards: FCC PART 15: 2008 Date of Receipt: 17 August 2009 Date of Test: 17 August to 08 September 2009 Date of Issue: 10 September 2009 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEMO09080483601 Page: 2 of 22 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Test Summary Test Test Requirement Standard Paragraph Result Conducted Emission FCC PART 15 : 2008 Section 15.207 PASS Flied Strength of Fundamental FCC PART 15 : 2008 Section 15.249 (a) PASS Flied Strength of Harmonics or other Frequency Emission FCC PART 15 : 2008 Section 15.249 (a) Section 15.209/15.205 PASS Occupied Bandwidth FCC PART 15 : 2008 Section 15.249 PASS SGS-CSTC Standards Technical Services Ltd. Report No.: SZEMO09080483601 Page: 3 of 22 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Contents Page 1 COVER PAGE ..........…

Text truncated - open the document above for the full version.

1 Photographs - Test Setup Radiated Emission Spurious Emission Conducted Emission