XTR301142BRF Transceiver (Controller)

 U3 Main control chip PIC16F722-SSOP Voltage Regulator Control Sticks U2 2.4G RF module nRF24L01+ OSC 16MHz ANT 2410 – 2460 MHz CECS SCK MOSI MISO INT Y1 TX U1, T3, T4 P1, P2 nRF24L01 Product Specification 1.2 Block diagram Figure 1. nRF24L01 block diagram RF Receiver XC1XC2 ANT1 ANT2 Enhanced ShockBurst Baseband Engine TX FIFOs RX FIFOs Radio Control GFSK Modulator SPI PA LNA TX Filter RX Filter RF Synthesiser Power Management RF Transmitter Baseband CSN SCK MISOMOSI IRQ CE VSS VDD DVDD VDD_PA GFSK Demodulator Register map IREF

FCC ID: XTR301142B Ophoto1 Ophoto2 FCC ID: XTR301142B Ophoto3 Ophoto4 FCC ID: XTR301142B Ophoto5

Label size: 62mm X 17mm

FCC ID: XTR301142B Iphoto1 Iphoto2 FCC ID: XTR301142B Iphoto3 Iphoto4 FCC ID: XTR301142B Iphoto5

FCC ID: XTR301142B Technical Description : The brief circuit description is listed as follows : - U3 (PIC16F722-SSOP) and associated circuit act as MCU. - U2 (nPF24L01+) and associated circuit act as 2.4G RF Module. - Y1 and associated circuit act as 16 MHz Oscillator. - T1, T2 and associated circuit act as Battery Charger. - U1, T3, T4 and associated circuit act as Voltage Regulator. - P1, P2 and associated circuit act as Joystick. The user should turn ON the controller and RF bird for link up prcoess before use. In each link up process, the controller is used 6 channels (CH1-CH6) in sequence for searching the corresponding RF bird. After link up, the controller is used single channels for operation. Antenna Used : An integral antenna (non-extendable) has been used. Frequency Table: Channel Frequency (MHz) 1 2410 2 2420 3 2430 4 2440 5 2450 6 2460 All rights reserved. Reproduction in whole or in part is prohibited without the prior written permission of the copyright holder. July 2007 nRF24L01 Single Chip 2.4GHz Transceiver Product Specification Key Features •Worldwide 2.4GHz ISM band operation •Up to 2Mbps on air data rate •Ultra low power operation •11.3mA TX at 0dBm output power •12.3mA RX at 2Mbps air data rate •900nA in power down •22μA in standby-I •On chip voltage regulator •1.9 to 3.6V supply range •Enhanced ShockBurst™ •Automatic packet handling •Auto packet transaction handling •6 data pipe MultiCeiver™ •Air compatible with nRF2401A, 02, E1 and E2 •Low cost BOM •±60ppm 16MHz crystal •5V tolerant inputs •Compact 20-pin 4x4mm QFN package Applications •Wireless PC Peripherals •Mouse, keyboards and remotes •3-in-one desktop bundles •Advanced Media center remote controls •VoIP headsets •Game controllers •Sports watches and sensors •RF remote controls for consumer electronics •Home and commercial automation •Ultra low power sensor networks •Active RFID •Asset tracing systems •Toys Revision 2.0 Page 2 of 74 nRF24L01 Product Specification Liability disclaimer Nordic Semiconductor ASA reserves the right to make changes without further notice to the product to improve reliability, function or design. Nordic Semiconductor ASA does not assume any liability arising out of the application or use of any product or circuits described herein. All application information is advisory and does not form part of the specification. Limiting values Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the specifications are not implied. Exposure to limiting values for extended periods may affect device reliability. Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Nordic Semiconductor ASA cus- tomers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Nordic Semiconductor ASA for any damages resulting from such improper use or sale. Contact details Visit www.nordicsemi.no for Nordic Semiconductor sales offices and distributors worldwide Main office: Otto Nielsens vei 12 7004 Trondheim Phone: +47 72 89 89 00 Fax: +47 72 89 89 89 www.nordicsemi.no Data sheet status Objective product specificationThis product specification contains target specifications for product development. Preliminary product specification This product specification contains preliminary data; supplementary data may be published from Nordic Semiconductor ASA later. Product specificationThis product specification contains final product specifications. Nordic Semiconductor ASA reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Revision 2.0 Page 3 of 74 nRF24L01 Product Specification Writing Conventions This product specification follows a set of typographic rules that makes the document consistent and easy to read. The following writing conventions are used: •Commands, bit state conditions, and register names are written in Courier. •Pin names and pin signal conditions are written in Courier bold. •Cross references are underlined and highlighted in blue . Revision History DateVersionDescription July 20072.0 •Restructured layout in a new template •Added details of the following features: XDynamic Payload Length (DPL) XAcknowledgement Payload (ACK_PLD) XFeature register XACTIVATE SPI command XSelective Auto Acknowledgement (NO_ACK) Revision 2.0 Page 4 of 74 nRF24L01 Product Specification Contents 1Introduction ............................................................................................... 7 1.1Features ............................................................................................... 8 1.2Block diagram ...................................................................................... 9 2Pin Information .......................................................................................... 10 2.1Pin assignment..................................................................................... 10 2.2Pin functions......................................................................................... 11 3Absolute maximum ratings ...................................................................... 12 4Operating conditions ................................................................................ 13 5Electrical specifications ........................................................................... 14 5.1Power consumption.............................................................................. 14 5.2General RF conditions ......................................................................... 15 5.3Transmitter operation ........................................................................... 15 5.4Receiver operation ................................…

Text truncated - open the document above for the full version.

1 2 3 4 56 ABCD 6 5 4 3 2 1 D CBA Title Number Revision Size B Date: 22-Aug-2009 Sheet of File: C:\Documents and Settings\Administrator\ 桌面 \TIMBi rd _v1r3.dd b Drawn By: CE 1 CSN 2 SCK 3 MOSI 4 MISO 5 IRQ 6 VDD 7 VSS 8 XC2 9 XC1 10 VDD_PA 11 ANT1 12 ANT2 13 VSS 14 VDD 15 IREF 16 VSS 17 VDD 18 DVDD 19 VSS 20 nRF24L01+ U2 nRF24L01+ Y116 MHz R121M C1722pF C1822pF L18.2nH L32.7nHL23.9nH C151.5pF C204.7pF C161.0pF C192.2nF C14 33nF R722K VDD3 ANT D4LED D2LED D1LED D3LED R10270 R9270 R8270 R168.2k 1% VCharge 12 J1PILES 12 J3CHARGE IN 3 GND 1 OUT 2 U1 MCP1702 C101u C111u VDD3 LED_Throttle LED_Charge VDD3 Axe Y1 Axe X2 CECSSCKMOSIMISOINT R122k 1%R210k 1% VBat C21100n C22100n VDD3 VDD3 C510n C7 10n C121u VDD3 C6 10n C810n VDD3 Axe Y2 Axe X1 VBatAxe X1Axe X2Axe Y1Axe Y2 LED_FREQ2LED_ThrottleLED_Charge INTMOSIMISOSCKCSCEICCLKICDAT MCLR TIMBird Emetteur 001 002 R310k 1% VDD R143.3 / 1% / 0.25W PWM_CH PWM_CH VCharge 12345 J2CON5 VDD3 MCLRICDATICCLK R154.7k C310n C910n R11270 LED_FREQ1 LED_FREQ2 LED_FREQ1 C1 16u 16v VDD C4 10n C131n R6inf R131k VDD T2 MMBT3904LT1 C210n R510k VDD3 P1JOYSTICK P2JOYSTICK VDD 20 VSS 8 VSS 19 RB3/AN9 24 RC1/CCP2 12 RC2/CCP1 13 RB7/ICSPDAT 28 RB6/ICSPCLK 27 RE3/MCLR 1 RA5/AN4/SS 7 RC3/SCL 14 RC4/SDA 15 RC5/SDO 16 RC6/TX 17 RC7/RX 18 RA3/VREF 5 RA0/AN0 2 RA1/AN1 3 RA2/AN2 4 RA4 6 RA7 9 RB0/INT 21 RB1/AN10 22 RB2/AN8 23 RB4/AN11 25 RB5/AN13 26 RC0 11 RA6/VCAP 10 U3 PIC16F722-SSOP C231u 12 J5LED 12 J4LED FR4 er=4.4 W line=1.5mm 2.45GHzLambda 0 = 122mmLambda FR4 = 122mm * 0.75 = 92 mmL = 92 / 4 = 23mm T1ZXTP2041F T3 PNP T4NPN D5DOUBLE_DIODE S1SW R410k R20470 R1710k R214.7k R1810k VDD3 ONOFFPWR ONOFF PWR R220 R1910k VDD3 S2TEST

INTERTEK TESTING SERVICES Report No.:HK09090899-1 Sample No.:1/1 Code: FCC15C_c / Effective Date: 11 Sep 2009 ( of ) Bandedge Plot – Pursuant to FCC Part 15 Section 15. 249 Requirement (Pass)

- The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. - This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com TEST REPORT Report No.: HK09090899-1 De Ruymbeke Ltd. Application For Certification (Original Grant) (FCC ID: XTR301142B) Transceiver Prepared and Checked by: Approved by: Leung Siu Lung, Michael Engineer Chan Chi Hung, Terry Senior Lead Engineer Date: January 7, 2010 INTERTEK TESTING SERVICES Report No.: HK09090899-1 FCC ID: XTR301142B i GENERAL INFORMATION De Ruymbeke Ltd. MODEL: 301142 FCC ID: XTR301142B Grantee: De Ruymbeke Ltd. Grantee Address: 22, Bd, Bourre, 13008, Marseille, France. Contact Person: Van Ruymbeke Tel: 0033 491 732712 Fax: 0033 491 732597 e-mail: [email protected] Manufacturer: N/A Manufacturer Address: N/A Brand Name: Avitron Model: 301142 Type of EUT: Transciever Description of EUT: X-Tim Avitron R/C Bird Serial Number: N/A FCC ID: XTR301142B Date of Sample Submitted: September 23, 2009 Date of Test: November 23, 2009 Report No.: HK09090899-1 Report Date: January 7, 2010 Environmental Conidtions: Temperature: +10 to 40°C Humidity: 10 to 90% INTERTEK TESTING SERVICES Report No.: HK09090899-1 FCC ID: XTR301142B ii SUMMARY OF TEST RESULT De Ruymbeke Ltd. MODEL: 301142 FCC ID: XTR301142B TEST SPECIFICATION REFERENCE RESULTS Maximum Peak Output Power 15.247(b), (c) / RSS-210 A8.4 N/A Hopping Channel Carrier Frequencies Separation (for 2.4GHz Digital) 15.247(e) / RSS-210 A8.1 N/A 20dB Bandwidth of the Hopping Channel 15.247(a) / RSS-210 A8.1 N/A Number of Hopping Frequencies 15.247(e) / RSS-210 A8.1 N/A Average Time of Occupancy of Hopping Frequency 15.247(e) / RSS-210 A8.1 N/A Anteann Conducted Spurious Emissions 15.247(d) / RSS-210 A8.5 N/A Radiated Spurious Emissions 15.247(d) / RSS-210 A8.5 N/A RF Exposure Compliance 15.247(i) / RSS-Gen 5.5 N/A Transmitter Power Line Conducted Emissions 15.207 / RSS-Gen 7.2.2 N/A Transmitter Field Strength (for 27MHz) 15.227 / RSS-310 3.8 N/A Transmitter Field Strength (for 40MHz) 15.229 / RSS-210 A2.7 N/A Transmitter Field Strength, Bandwidth and Timing Requirement (for Remote Control) 15.231(a) / RSS-210 A1.1.1 N/A Transmitter Field Strength, Bandwidth and Timing Requirement (for 433MHz) 15.231(e) / RSS-210 A1.1.5 N/A Transmitter Field Strength and Bandwidth Requirement(for 88-108MHz) 15.239 / RSS-210 A2.8 N/A Transmitter Field Strength and Bandwidth Requirement(for 902- 928MHz or 2.4GHz) 15.249 / RSS-210 A2.9 Pass Transmitter Field Strength and Bandwidth Requirement (for 49MHz) 15.235 / RSS-310 3.9 N/A Receiver / Digital Device Radiated Eissions 15.109 / ICES-003 N/A Digital Device Conducted Emissions 15.107 / ICES-003 N/A Note: 1. The EUT uses a permanently attached antenna which, in accordance to section 15.203, is considered sufficient to comply with the pervisions of this section. 2. Pursuant to FCC part 15 Section 15.215(c), the 20 dB bandwidth of the emission was contained within the frequency band designated (mentioned as above) which the EUT operated. The effects, if any, from frequency sweeping, frequency hopping, other modulation techniques and frequency stability over excepted variations in temperature and supply voltage were considered. INTERTEK TESTING SERVICES Report No.: HK09090899-1 FCC ID: XTR301142B iii Table of Contents 1.0 General Description....................................................................................... 1 1.1 Product Description .......................................................................................... 1 1.2 Related Submittal(s) Grants.............................................................................. 1 1.3 Test Methodology............................................................................................. 1 1.4 Test Facility ...................................................................................................... 1 2.0 System Test Configuration ............................................................................ 2 2.1 Justification ...................................................................................................... 2 2.2 EUT Exercising Software.................................................................................. 2 2.3 Special Accessories ......................................................................................... 2 2.4 Equipment Modification .................................................................................... 2 2.5 Measurement Uncertainty................................................................................. 2 2.6 Support Equipment List and Description ........................................................... 3 3.0 Emission Results ........................................................................................... 3 3.1 Field Strength Calculation................................................................................. 3 3.2 Radiated Emissi…

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICES Front View Back View HK09090899-1 HK09090899-1