XUF217132-001MDMulti-carrier Power Amplifier

mitec telecom inc. Designers and manufacturers of telecom and wireless products 9000 Trans Canada, Pointe-Claire, Quebec, Canada H9R 5Z8 PRODUCT DOCUMENT Preliminary Released REVISION RECORD Revision ECN # Description Date Approved 0 - Preliminary release 03 Nov 09 P.Mousseau 1 Additional safety information regarding RF exposure. 07 Dec 09 P.Mousseau More detailed description of the MCPA architecture. 2 Combo D-SUB MCPA connector pin out added 09 Dec 09 P.Mousseau 3 Restricted Area notification (section 2.2) 14 Dec 09 P.Mousseau CM Approval Author: P. Mousseau, ing. DATE: 03 NOV 09 Technical Writer: n/a DATE: 03 NOV 09 TITLE 24W Remote Node MCPA Installation Instructions REV. 3 This document contains information proprietary to mitec telecom inc., or its affiliates, or to a third party to which mitec telecom inc. may have a legal obligation to protect such information from unauthorized disclosure, use, or duplication. Any disclosure, use, or duplication of this document or of any of the information contained herein is expressly prohibited except as mitec telecom inc. may otherwise agree in writing. DOCUMENT NO. 217132-001MA PAGE 1OF 18 REV. 3 This document contains information proprietary to mitec telecom inc., or its affiliates, or to a third party to which mitec telecom inc. may have a legal obligation to protect such information from unauthorized disclosure, use, or duplication. Any disclosure, use,or duplication of this document or of any of the information contained herein is expressly prohibited except as mitec telecom inc. may otherwise agree in writing. DOCUMENT NO. 217132-001MA PAGE 2 REV. 3 This document contains information proprietary to mitec telecom inc., or its affiliates, or to a third party to which mitec telecom inc. may have a legal obligation to protect such information from unauthorized disclosure, use, or duplication. Any disclosure, use,or duplication of this document or of any of the information contained herein is expressly prohibited except as mitec telecom inc. may otherwise agree in writing. DOCUMENT NO. 217132-001MA PAGE 3 Table of Contents 1.0 SCOPE ......................................................................................................................................................................... 4 2.0 SYSTEM OVERVIEW.................................................................................................................................................. 5 2.1 GENERAL DESCRIPTION.............................................................................................................................................................. 5 2.1.1 Abbreviations and Explanations......................................................................................................................................... 5 2.2 PREPARING FOR INSTALLATION.................................................................................................................................................. 5 2.3 SAFETY PRECAUTIONS................................................................................................................................................................ 6 2.4 WARRANTY INFORMATION......................................................................................................................................................... 6 2.4.1 Equipment Damage or Loss ............................................................................................................................................... 7 2.4.2 Return of Equipment .......................................................................................................................................................... 7 3.0 SYSTEM INSTALLATION .......................................................................................................................................... 8 3.1 SYSTEM BLOCK DIAGRAM.......................................................................................................................................................... 8 3.2 INSTALLATION OVERVIEW.......................................................................................................................................................... 9 3.2.1 24W Remote Node MCPA Installation............................................................................................................................ 11 3.2.1.1 24W Remote Node MCPA Pole Mounting.................................................................................................................. 11 3.2.1.2 Optional 24W Remote Node MCPA Flat Wall Surface Mounting....................................................................... 13 4.0 SYSTEM VERIFICATION TEST ................................................................................................................................ 15 APPENDIX A MCPA CONNECTOR PIN OUT............................................................................................................... 17 APPENDIX B FAN CONTROLLER BOARD J3 CONNECTOR PIN OUT .................................................................... 18 List of Figures Figure 1 – System Block Diagram ............................................................................................................................................................. 8 Figure 2 – 20W MCPA Remote Node Block Diagram.............................................................................................................................. 8 Figure 3 – Wall mount or pole mount installation ..................................................................................................................................... 9 Figure 4 – Required Hardware................................................................................................................................................................... 9 Figure 5 – Recommended Test Setup ..........................................................…

Text truncated - open the document above for the full version.

Regulatory Affairs Contract Engineering Open EXHIBIT 2 1 (1) Prepared (also subject responsible if other) No. EWU/PR/HD Keith Goshia Approved Checked Date Rev Reference 11/03,2009 A XUF217132-001MD Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Attention: Equipment Authorization Branch Subject: Request for Confidentiality To Whom It May Concern: We, Mitec Telecom Inc., hereby request that the Exhibits/Items listed below be withheld from public inspection in accordance with Sections 0.457 and 0.459 of the Commission’s Rules. This due to the following reasons: There are advanced technical and design solutions/information in the Exhibits/Items, as mentioned above, that we regard as Mitec proprietary, with actual and potential patents pending. The information can be advantageous to our competitors as well as sources seeking ways to hack past the built in security functionality. These solutions or information thereof are not accessible even for our customers or partners unless non-disclosure agreements for particular item(s) have been signed. Confidential product information can be found in, but not necessarily limited to, block diagrams, schematics diagrams, and parts lists as well as technical circuit description. Those documents can only be accessible by the customers who purchase our Fiber Span and accept the conditions and therefore are provided with unique information access tools. EXHIBIT 10 N/A EXHIBIT 11 Block Diagram EXHIBIT 12 Schematics EXHIBIT 13 Parts List EXHIBIT 14 Technical Circuit Description Regards, If any further information is required, please contact me directly. Also, would you please inform me when the Request for Confidentiality has been accepted and granted? Regards, Keith A. Goshia Principal Regulatory Engineer Regulatory Affairs Contract Engineering 18700 Wagon Trail Mead, CO 80542 Telephone: (720) 352-9624 e-mail: [email protected]

Open EXHIBIT 4 1 (1) Prepared (also subject responsible if other) No. EWU/PR/HD Keith Goshia Approved Checked Date Rev Reference 11/3/2009 A XUF217132-011MD Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Attention: Equipment Authorization Branch External Photos:

December 11, 2009 ATTN: Keith A.Goshia Regulatory Affairs Contract Engineering 18700 Wagon Trial Mead, CO 80542 (720)352-9624 [email protected] http://www.regulatoryaffairs-ce.com Dear Sir: Subject: Label Sample The following picture shows a label sample that will be placed on the Front Panel of Mitec Uni- Directional SMR Downlink unit P/N: 217132-001MD . Should you have any questions regarding this request, please address them to the undersigned. Mitec Telecom Inc. Sincerely, _______________________________ Dec 11, 2009 Name: Pierre Mousseau, ing. [date] Title: Engineering Program Manager



3299 Boul. Jean-Baptiste-Deschamps Lachine, Quebec, Canada H8T 3E4

Regulatory Affairs Contract Engineering EXHIBIT 8 1 (2) Prepared (also subject responsible if other) No. EWU/PR/HD Keith Goshia Approved Checked Date Rev Reference 11/3/2009 A XUF217132-011MD Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Attention: Equipment Authorization Branch Internal Photo’s Regulatory Affairs Contract Engineering EXHIBIT 8 2 (2) Prepared (also subject responsible if other) No. EWU/PR/HD Keith Goshia Approved Checked Date Rev Reference 11/3/2009 A XUF217132-011MD

FCC Part 90 Report Sub-part 2.1033 (c): Equipment Identification FCC ID: XUF217132-011MD Date of Report 03 November 2009 The applicant has been cautioned as to the following: 15.21 Information to User. The user’s manual or instruction manual for an intentional radiator shall caution the user that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 15.27 (a) Special Accessories. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer, without additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. Table of Contents Rule Description 2.1033 List of General Information Required 2.1046 R.F. Power Output 2.1049 Occupied Bandwidth 90.490 Emission Requirements 2.1051 Spurious Emissions at Antenna Terminals 90.490 2.1053 Field Strength of Spurious Radiation 2.1055 Frequency Stability - Temperature 2.202 (g) Necessary Bandwidth and Emission Bandwidth 2.906 Testimonial & Statement of Certification Radio Frequency Radiation Exposure Limits Exhibits: Appendix: List of General Information Required for Type Acceptance In Accordance with FCC Rules and Regulations, Volume II, Part 2 and to Part 90 Sub Part S Sub-part 2.1033 (c)(1) Name and Address of Applicant: Mitec Telecom Inc. 3299 Jean-Baptiste-Deschamps Boulevard Lachine, Quebec, H8T 3E4 Vendor: Applicant 2.1033(c)(2): FCC ID: XUF217132-001MD 2.924 Model No 217132-001MD Technical Description: 2.1033(c)(4): Type of Emission: AMP 2.1033(c)(5) Frequency Range, MHz: 851MHz-869MHz 2.1033(c)(6) Power Rating, Watts: 24 Watts Switchable Adjustable x N/A 2.1033(c)(7) Maximum Power Rating, Watts: 24 Watts 2.1033(c)(8) Voltages & Currents in all Elements in Final R.F. Stage, Including Final Transistor or Solid State Device: Collector Voltage, VAC 115V = per manual Open Exhibits 2.1033 Cover Letter: Please see Attached Exhibit 1 2.1033 Cover Letter Confidentiality: Please see Attached Exhibit 2 2.1033 Cover Letter Temperature Range: Please see Attached Exhibit 3 2.1033 External Photo’s: Please see Attached Exhibits 4 2.1033 Photo FCC ID: Please see Attached Exhibit 5 2.1033 Tune-Up Procedure: Please see Attached Exhibit 6 2.1033 Test Report: Please see Attached Exhibit 7 (This doc.) 2.1033 Installation Instruction: Please see Attached Exhibit 12 Confidenital Exhibits 2.1033 Internal Photo’s: Please see Attached Exhibit 8 2.1033 System Block Diagram: Please see Attached Exhibit 9 2.1033 Schematics: Please see Attached Exhibit 10 2.1033 Technical Description: Please see Attached Exhibit 11 2.1033 Parts List: Please see Attached Exhibit 13 2.1033 Technical Circuit Description: Please see Attached Exhibit 14 2.1033(c)(14) Test Report: Test Report Follows Sub-part 2.1033 (c) : Test and Measurement Data All tests and measurement data shown were performed in accordance with FCC Rules and Regulations, Volume II; Part 2, Sub-part J, Sections 2.1046, 2.1049, 2.1051, 2.1053, 2.1055 and the following individual Parts: 21 Domestic Public Radio Services 24 Personal Communications Services ___ 27 Miscellaneous Wireless Communication Services _ _ 22E Broadband PCS __ 22.901 Special Provisions for Alternative Cellular Technologies and and Auxiliary Services 23 International Fixed Public Radio Communications Service 74 Experimental, Auxiliary & Special Broadcast and Other Program Distribution Services 74H Low Power Auxiliary Stations 80 Stations in the Maritime Service 80.209 (5)(I) Transmitter Frequency Tolerances, 156–162 MHz, Coast Stations 80K Private Coast Stations & Marine Utility Stations 80S Compulsory R/T Installations for Small Passenger Boats 80T Radio Telegraph Installation Required for Vessels on the Great Lakes 80U Radio Telegraph Installation Required by the Bridge–to–Bridge Act 87 Aviation Services 90 Private Land Mobile Radio Services X 94 Private Operational–Fixed microwave Services 95 General Mobile Radio Service Regulatory Affairs Contract Engineering TEST REPORT 11 (45) Prepared (also subject responsible if other) No. EWU/PR/HD Keith A. Goshia Approved Checked Date Rev Reference 11/3/2009 A XUF217132-001MD General Information 1. Spurious radiation was measured at three (3) meters. 2. The normal modes of modulation are: (a) Paging AMP X (b) Wideband Data (c) SAT (d) ST (e) SAT + Voice (f) SAT + DTMF (g) 16QAM or QPSK WCDMA (h) Pi/4 DQPSK (i) NAMPS Voice (j) NAMPS DSAT (k) NAMPS ST Standard Test Conditions and Engineering Practices Except as noted herein, the following conditions and procedures were observed during the testing: Room Temperature = 25 ± 5° C Room Humidity = 20–50% Supply Voltage 115 VAC Prior to testing, the E.U.T. was tuned up in accordance with the manufacturer’s alignment procedures. All external gain controls were maintained at the position of maximu…

Text truncated - open the document above for the full version.