Y23V68Two-way Radio

FCC Warnning Any Changes expressly or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. SAR tests are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. Before a new model device is a available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit established by the FCC, Tests for each device are performed in positions and locations (e.g. at the ear and worn on the body)as required by the FCC. This radio complies with FCC exposure limits for uncontrolled environment at operating duty factors of up to 50% .The device was test for typical body-worn operations and head face up operations keep the device at least 25mm from the face.

6LJQDWXUH 7\SHGRU3ULQWHG1DPHChengji Chen 7LWOHGeneral Manager '(&/$5$7,21 'DWH2021-01-07 )('(5$/&20081,&$7,216&200,66,21 $XWKRUL]DWLRQDQG(YDOXDWLRQ'LYLVLRQ 2DNODQG0LOOV5RDG &ROXPELD0' 'HDU6LURU0DGDP :H Iradio Electronics Co., Ltd.KHUHE\GHFODUHWKDWSURGXFWQDPH Two-way Radio PRGHOQDPHV68 PLUS, V5, V68, V68PLUS, T1000. FCC ID: Y23V68). These models are identical with the PCB design, components and electromagnetics compatibility characteristics. V68 PLUS has been tested by BACL. 7KHGLIIHUHQFHVRIWKHPDUHDVIROORZV 0RGHOQDPH 3OHDVHFRQWDFWPHLIWKHUHLVQHHGIRUDQ\DGGLWLRQDOFODULILFDWLRQRULQIRUPDWLRQ %HVW5HJDUGV Company: Iradio Electronics Co., Ltd. ADD: No.16 Daxiamei Industrial Area, Nan'an, Quanzhou City, China TEL: 86-595-86759888 FAX: 86-595-86758999 Mail Address: [email protected]

QA-FR-171-A Company: Iradio Electronics Co., Ltd. ADD: No.16 Daxiamei Industrial Area, Nan'an, Quanzhou City, China TEL: 86-595-86759888 FAX: 86-595-86758999 Mail Address: [email protected] FCC Confidential Authorization 202 1-01-07 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: Y23V68 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Iradio Electronics Co., Ltd., hereby requests long-term confidential treatment of information accompanying this application as outlined below: •Block Diagram •Schematics •Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature: Typed or Printed Name: Chengji Chen Title: General Manager • BOM/Tune-up

EXHIBIT A - EUT EXTERNAL PHOTOGRAPHS Antenna

XHIBIT B - EUT INTERNAL PHOTOGRAPHS

SAR EVALUATION REPORT For Iradio Electronics Co., Ltd. No.16 Daxiamei Industrial Area, Nan'an, Quanzhou City, China FCC ID: Y23V68 Report Type: Original Report Product Type: Two-way Radio Report Number: RXM210107050-20 Report Date: 2021-02-01 Reviewed By: Brave Lu SAR Engineer Prepared By: Bay Area Compliance Laboratories Corp. (Dongguan) No.12, Pulong East 1 st Road, Tangxia Town, Dongguan, Guangdong, China Tel: +86-769-86858888 Fax: +86-769-86858891 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RXM210107050-20 SAR Evaluation Report 2 of 32 Attestation of Test Results EUT Information EUT Description Two-way Radio Tested Model V68 PLUS Multiple Models V5, V68, V68PLUS, T1000 FCC ID Y23V68 Serial Number RXM210107050-SA-S1 Test Date 2021-01-08 Mode Test Model Max. SAR Level(s) Reported(W/kg) Limit MURS 1g Head SAR (Face Up) 0.19 1.6 (W/kg) 1g Body SAR (Body Back) 0.69 Applicable Standards FCC 47 CFR part 2.1093 Radiofrequency radiation exposure evaluation: portable devices IEEE1528:2013 IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques IEC 62209-2:2010 Human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices-Human models, instrumentation, and procedures-Part 2: Procedure to determine the specific absorption rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz) KDB procedures KDB 447498 D01 General RF Exposure Guidance v06 KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz v01r04 KDB 865664 D02 RF Exposure Reporting v01r02 KDB 643646 D01 SAR Test for PTT Radios v01r03 Note: This wireless device has been shown to be capable of compliance for localized specific absorption rate (SAR) for General Population/Uncontrolled Exposure limits specified in FCC 47 CFR part 2.1093 and has been tested in accordance with the measurement procedures specified in IEEE 1528-2013 and RF exposure KDB procedures. The results and statements contained in this report pertain only to the device(s) evaluated. Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RXM210107050-20 SAR Evaluation Report 3 of 32 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ......................................................................................................................... 4 EUT DESCRIPTION .................................................................................................................................................... 5 TECHNICAL SPECIFICATION ......................................................................................................................................... 5 REFERENCE, STANDARDS, AND GUIDELINES .................................................................................................. 6 SAR LIMITS ................................................................................................................................................................. 6 FACILITIES .................................................................................................................................................................. 7 DESCRIPTION OF TEST SYSTEM .......................................................................................................................... 8 EQUIPMENT LIST AND CALIBRATION ............................................................................................................. 13 EQUIPMENTS LIST & CALIBRATION INFORMATION .................................................................................................... 13 SAR MEASUREMENT SYSTEM VERIFICATION .............................................................................................. 14 LIQUID VERIFICATION ............................................................................................................................................... 14 SYSTEM ACCURACY VERIFICATION ........................................................................................................................... 15 SAR SYSTEM VALIDATION DATA ..................................................................................................................... 16 EUT TEST STRATEGY AND METHODOLOGY ................................................................................................. 18 TEST POSITIONS FOR DEVICE OPERATING NEXT TO A PERSON’S EAR........................................................................ 18 CHEEK/TOUCH POSITION ........................................................................................................................................... 19 EAR/TILT POSITION ................................................................................................................................................... 19 TEST POSITIONS FOR BODY-WORN AND OTHER CONFIGURATIONS .............................................................................. 20 TEST DISTANCE FOR SAR EVALUATION .................................................................................................................... 20 SAR EVALUATION PROCEDURE ................................................................................................................................. 21 CONDUCTED OUTPUT POWER MEASUREMENT ........................................................................................... 22 PROVISION APPLICABLE ............................................................................................................................................ 22 TEST PROCEDURE ...................................................................................................................................................... 22 MAXIMUM TARGET OUTPUT POWER ......................................................................................................................... 22 T…

Text truncated - open the document above for the full version.

APPENDIX C PROBE CALIBRATION CERTIFICATES DIPOLE CALIBRATION CERTIFICATES DIPOLE CALIBRATION CERTIFICATES

Report No.: RXM210107050-20 Page 1 of 10 Plot 1#: FM_11.25kHz_151.82MHz_Face Up DUT: Two-way Radio; Type: V68 PLUS; Serial: RXM210107050-SA-S1 Communication System: FM; Frequency: 151.82 MHz;Duty Cycle: 1:1 Medium parameters used: f = 151.82 MHz; σ = 0.755 S/m; ε r = 52.306; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration:  Probe: ES3DV2 - SN3019; ConvF(7.7, 7.7, 7.7) @ 151.82 MHz; Calibrated: 2020/11/16  Sensor-Surface: 4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn1354; Calibrated: 2020/9/30  Phantom: ELI v8.0; Type: QDOVA002AA; Serial: TP:2051  Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.12 (7470) Area Scan (61x161x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.259 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 15.80 V/m; Power Drift = -0.19 dB Peak SAR (extrapolated) = 0.322 W/kg SAR(1 g) = 0.237 W/kg; SAR(10 g) = 0.183 W/kg Maximum value of SAR (measured) = 0.247 W/kg 0 dB = 0.247 W/kg = -6.07 dBW/kg Report No.: RXM210107050-20 Page 2 of 10 Plot 2#: FM_11.25kHz_151.88MHz_Face Up DUT: Two-way Radio; Type: V68 PLUS; Serial: RXM210107050-SA-S1 Communication System: FM; Frequency: 151.88 MHz;Duty Cycle: 1:1 Medium parameters used: f = 151.88 MHz; σ = 0.759 S/m; ε r = 52.198; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration:  Probe: ES3DV2 - SN3019; ConvF(7.7, 7.7, 7.7) @ 151.88 MHz; Calibrated: 2020/11/16  Sensor-Surface: 4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn1354; Calibrated: 2020/9/30  Phantom: ELI v8.0; Type: QDOVA002AA; Serial: TP:2051  Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.12 (7470) Area Scan (61x161x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.222 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 14.14 V/m; Power Drift = -0.10 dB Peak SAR (extrapolated) = 0.281 W/kg SAR(1 g) = 0.208 W/kg; SAR(10 g) = 0.162 W/kg Maximum value of SAR (measured) = 0.217 W/kg 0 dB = 0.217 W/kg = -6.64 dBW/kg Report No.: RXM210107050-20 Page 3 of 10 Plot 3#: FM_11.25kHz_151.94MHz_Face Up DUT: Two-way Radio; Type: V68 PLUS; Serial: RXM210107050-SA-S1 Communication System: FM; Frequency: 151.94 MHz;Duty Cycle: 1:1 Medium parameters used: f = 151.94 MHz; σ = 0.764 S/m; ε r = 52.087; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration:  Probe: ES3DV2 - SN3019; ConvF(7.7, 7.7, 7.7) @ 151.94 MHz; Calibrated: 2020/11/16  Sensor-Surface: 4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn1354; Calibrated: 2020/9/30  Phantom: ELI v8.0; Type: QDOVA002AA; Serial: TP:2051  Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.12 (7470) Area Scan (61x161x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.202 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 13.09 V/m; Power Drift = -0.13 dB Peak SAR (extrapolated) = 0.255 W/kg SAR(1 g) = 0.191 W/kg; SAR(10 g) = 0.149 W/kg Maximum value of SAR (measured) = 0.198 W/kg 0 dB = 0.198 W/kg = -7.03 dBW/kg Report No.: RXM210107050-20 Page 4 of 10 Plot 4#: FM_20kHz_154.57MHz_Face Up DUT: Two-way Radio; Type: V68 PLUS; Serial: RXM210107050-SA-S1 Communication System: FM; Frequency: 154.57 MHz;Duty Cycle: 1:1 Medium parameters used: f = 154.57 MHz; σ = 0.768 S/m; ε r = 51.986; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration:  Probe: ES3DV2 - SN3019; ConvF(7.7, 7.7, 7.7) @ 154.57 MHz; Calibrated: 2020/11/16  Sensor-Surface: 4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn1354; Calibrated: 2020/9/30  Phantom: ELI v8.0; Type: QDOVA002AA; Serial: TP:2051  Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.12 (7470) Area Scan (61x161x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.349 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 17.37 V/m; Power Drift = -0.13 dB Peak SAR (extrapolated) = 0.441 W/kg SAR(1 g) = 0.328 W/kg; SAR(10 g) = 0.253 W/kg Maximum value of SAR (measured) = 0.342 W/kg 0 dB = 0.342 W/kg = -4.66 dBW/kg Report No.: RXM210107050-20 Page 5 of 10 Plot 5#: FM_20kHz_154.6MHz_Face Up DUT: Two-way Radio; Type: V68 PLUS; Serial: RXM210107050-SA-S1 Communication System: FM; Frequency: 154.6 MHz;Duty Cycle: 1:1 Medium parameters used: f = 154.6 MHz; σ = 0.772 S/m; ε r = 51.897; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration:  Probe: ES3DV2 - SN3019; ConvF(7.7, 7.7, 7.7) @ 154.6 MHz; Calibrated: 2020/11/16  Sensor-Surface: 4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn1354; Calibrated: 2020/9/30  Phantom: ELI v8.0; Type: QDOVA002AA; Serial: TP:2051  Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.12 (7470) Area Scan (61x161x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.382 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 19.57 V/m; Power Drift = -0.12 dB Peak SAR (extrapolated) = 0.491 W/kg SAR(1 g) = 0.355 W/kg; SAR(10 g) = 0.272 W/kg Maximum value of SAR (measured) = 0.370 W/kg 0 dB = 0.370 W/kg = -4.32 dBW/kg Report No.: RXM210107050-20 Page 6 of 10 Plot 6#: FM_11.25kHz_151.82MHz_Body Back DUT: Two-way Radio; Type: V68 PLUS; Serial: RXM210107050-SA-S1 Communication System: FM; Frequency: 151.82 MHz;Duty Cycle: 1:1 Medium parameters used: f = 151.82 MHz; σ = 0.791 S/m; ε r = 61.894; ρ = 1000 kg/m 3 Phantom section: Flat Section DASY5 Configuration:  Probe: ES3DV2 - SN3019; ConvF(7.38, 7.38, 7.38) @ 151.82 MHz; Calibrated: 2020/11/16  Sensor-Surface: 4mm (Mechanical Surface Detection)  Electronics: DAE4 Sn1354; Calibrated: 2020/9/30  Phantom: ELI v8.0; Type: QDOVA002AA; Serial: TP:2051  Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.12 (7470) Area Scan (61x161x1): Interpolated grid: dx=1.500 mm, dy=1.500 m…

Text truncated - open the document above for the full version.

Report No.: RXM210107050-20 Page 1 of 2 APPENDIX B EUT TEST POSITION PHOTOS Liquid depth ≥ 15cm Report No.: RXM210107050-20 Page 2 of 2 Face Up Setup Photo(25mm) Body Back Setup Photo(0mm) 35mm 25mm 25mm

FCC PART 95 TEST REPORT For Iradio Electronics Co., Ltd. No.16 Daxiamei Industrial Area, Nan'an, Quanzhou City, China Report Type: Original Report Product Type: Two-way Radio Project Engineer: CK Huang Re port Number: RXM210107050-00B Re port Date: 2021-02-07 Reviewed B y: Oscar Ye EMC Manager Prepared By: Bay Area Compliance Laboratories Corp. (Kunshan) No.248 Chenghu Road, Kunshan, Jiangsu province, China Tel: +86-0512-86175000 Fax: +86-0512-88934268 www.baclcorp.com.cn FCC ID: Y23V68 Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RXM210107050-00B FCC Part 95 Page 2 of 26 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 3 OBJECTIVE ................................................................................................................................................................... 3 RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................................. 3 TEST METHODOLOGY .................................................................................................................................................. 3 MEASUREMENT UNCERTAINTY .................................................................................................................................... 4 TEST FACILITY ............................................................................................................................................................. 4 SYSTEM TEST CONFIGURATION .......................................................................................................................... 5 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 5 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 5 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 5 EXTERNAL I/O CABLE .................................................................................................................................................. 5 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 6 SUMMARY OF TEST RESULTS ............................................................................................................................... 7 TEST EQUIPMENT LIST ........................................................................................................................................... 8 FCC §1.1307(b) & 2.1093 - RF EXPOSURE INFORMATION ................................................................................ 9 MEASUREMENT RESULT .............................................................................................................................................. 9 FCC §2.1046, §95.2767 - RF OUTPUT POWER ...................................................................................................... 10 APPLICABLE STANDARD ............................................................................................................................................ 10 TEST PROCEDURE ...................................................................................................................................................... 10 TEST DATA ................................................................................................................................................................ 10 FCC §2.1049, §95.2773 & §95.2779(a) - OCCUPIED BANDWIDTH AND EMISSION MASK ......................... 11 APPLICABLE STANDARD ............................................................................................................................................ 11 TEST PROCEDURE ...................................................................................................................................................... 12 TEST DATA ................................................................................................................................................................ 12 FCC §2.1051 & §95.2779 - SPURIOUS EMISSIONS AT ANTENNA TERMINALS .......................................... 15 APPLICABLE STANDARD ............................................................................................................................................ 15 TEST PROCEDURE ...................................................................................................................................................... 15 TEST DATA ................................................................................................................................................................ 15 FCC §2.1053 & §95.2779 - RADIATED SPURIOUS EMISSION .......................................................................... 18 APPLICABLE STANDARD ............................................................................................................................................ 18 TEST PROCEDURE ...................................................................................................................................................... 18 TEST DATA ................................................................................................................................................................ 18 FCC§2.1055 (d), §95.2765 - FREQUENCY STABILITY ........................................................................................ 20 APPLICABLE STANDARD .................…

Text truncated - open the document above for the full version.

EXHIBIT C - TEST SETUP PHOTOGRAPHS RadiatedEmissions (Below 1GHz) RadiatedEmissions (Above 1GHz)