Y55WSS0001Wireless Entrapment Protection Device

Specifications are subject to change without notice (21.12.2010)1 Product Description Wireless Entrapment Protec- tion Device for Industrial Doors. The system is designed to replace the con- nection cable between the ESPE (electro-sensitive pro- tective equipment) and the door controller. The sub mod- ule has input for either, N.C. ESPE, N.O. 8.2 koHm ESPE or our own low consumption photoelectric ESPE N.C. con- tact. The system is designed for high reliability using 2.4 GHz duplex communica- tion between the main and sub module. The main mod- ule can handle up to 4 sub modules i.e. one system can handle 8 ESPEs. The sub module is put to live by a test signal from the main module and sat awake for the time set at then sub module up to 80 seconds. • Wireless Entrapment Protection Device for Industrial Doors • Replaces cable between Door controller and ESPE • Input for two ESPE (electro-sensitive protective equipment) • Input for door-in-door sensor • Output ESPE 1 x SPST NC, 1 x SPDT NO (8,2koHm) • Output low battery 1 x SPST NC contact • 2,4 GHz duplex communication • Built-in antenna • Approval according to ???? • IP66 ratings Wireless Entrapment Protection Device For Industrial Doors ESPE Type WSM / WSS ... Type Selection Housing RangeType Ordering no. W x H x D Wireless 75 x 125 x 35 mm 10 mMain Module WSM 2 B A 2 D24 45 x 214 x 22 mm 10 mSub Module WSS 2 B A 2 BAT Housing RangeType Ordering no. W x H x D S n Ø11 x 24.5 mm 15 mEmitter PB 11 CNT 15 WE Ø11 x 24.5 mm 15 mReceiver PB 11 CNT 15 WR Specifications Main module Rated operational volt. (U B ) 12 to 24 VAC/DC (-10 +15%) Ripple (U rpp ) ≤ 10% Supply current < 50 mA Communication Frequency 2.4 GHz Duplex Number of channels 16 selectable on DIP switch Sub module live time 10 – 80 Sec. Selectable on DIP-switches Relay ESPE NC SPST ESPE NO 8.2 koHm SPST Low Battery SPST DC11 ??? AC11 ??? Operations Minimum: 600’000 @ 0.5 A, 50 VAC/30 VDC Operations Minimum: 100’000 @ 0.5 A, 125 VAC/ 1A, 30 VDC Response time OFF-ON (t ON ) 50 mS ON-OFF (t OFF ) 50 mS Power ON delay (t V ) Main module < 300 mS Protection Reverse polarity, transients Indications Main Module Power supply Green LED ESPE 1 or 2 active 2 x yellow LEDs Low Battery Red LED Channels not synchronized Toggle red & green Test input (active high or active low) Selectable in DIP switch Active high “Description” Active low “Description” Ordering Key Function Main/Sub Module No of channels Mute function Adjustment Output Power supply WSM 2 B A 2 D24 IC 2Specifications are subject to change without notice (21.12.2010) WSM/WSS ... Specifications Main module (cont.) Test impulse time Minimum pulse width > 50 mS Maximum pulse width < 2 sec Operating frequency 500 Hz Response time OFF-ON (t ON ) ≤ 1.0 ms ON-OFF (t OFF ) ≤ 1.0 ms Environmental Installation category III Pollution degree 3 Degree of protection IP66 Rated insulation voltage 50 VDC Temperature Operating Temperature -25°to +60°C (-13°to +140°F) Storage Temperature -40°to +70°C (-40°to +158°F) Size 75 x 35 x 125 mm Material Housing Light Grey ABS Top Light Grey ABS Weight 230 g Approvals UL508 FCCport 15(C) 15.247 FCC ID: Y55WMM0001 ICRSS210 CE-marking EN12445, EN12453, EN12978 Radio Equipment and Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC Low Voltage Directive 73/23/EEC Electromagnetic Compatibility Directive 8973367EEC Machinery Directive 98/37/EC, amended by Directive 98/79/EC For industrial doors only See EN13241-1 Specifications Sub module Rated operational volt. (U B ) 1to 4 Lithium 3.6VDC size AA batteries 2 battery supplied with the sub-module Supply current < ?? mA Communication Frequency 2.4 GHz Duplex Number of channels 16 selectable on DIP switch Sub module live time 10 – 80 Sec. Selectable on DIP-switches in the main module ESPE inputs ESPE NC Standard NC ESPE ESPE NO 8.2 koHm Standard NO, 8.2 koHm Photoelectric ESPE Carlo Gavazzi Low current ESPE PES for wireless applications Door in door input NC input from Limit switch Response time OFF-ON (t ON ) 50 mS ON-OFF (t OFF ) 50 mS Power ON delay (t V ) Sub module after sleep <100 mS Protection Reverse polarity Indications Sub Module ESPE 1 Yellow LED ESPE 2 Yellow LED lights in 20 sec. after a short activation on the pushbutton Test input The submodule wake up after the test input of the main module Antenna Built in Environmental Installation category III Pollution degree 3 Degree of protection IP66 Rated insulation voltage 50 VDC Temperature Operating Temperature -25°to +55°C (-13°to +131°F) Storage Temperature -40°to +70°C (-40°to +158°F) Size 22 x 45 x 214 mm Material Housing Light Grey PC Top Black PC Weight 220 g Approvals UL508 FCCport 15(C) 15.247 FCC ID: Y55WSM0001 ICRSS210 CE-marking EN12445, EN12453, EN12978 Radio Equipment and Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC Low Voltage Directive 73/23/EEC Electromagnetic Compatibility Directive 8973367EEC Machinery Directive 98/37/EC, amended by Directive 98/79/EC For industrial doors only See EN13241-1 NOTE:Changes/modifications not approved by the responsible party could void the user’s authority to operate the equipment. NOTE:Changes/modifications not approved by the responsible party could void the user’s authority to operate the equipment. Specifications are subject to change without notice (21.12.2010)3 Operation Diagram Main Module 0 oHm 8,2 Kohm NO Contact Closed NO Contact Open t1t1t1t1 e.g. High voltage e.g. Low voltage t1t1t1t1 e.g. High voltage e.g. Low voltage Sub Module Interruption No interruption Awake mode Sleep mode t1 = 50 mS t2 = 500 mS t3 range from 10 to 80 S (t3 is always starts/restart after t2) Normal test Test while safety edge active Test while safety edge inactiveactive t2t2 t3 t2 t3 Output NO (8,2kohm) Test input Active High Test input Active Low Power supply t3 t2t2t2 t2 t3 t2 Output NC Power supply Safety edge active WSM/WSS ... Wiring Diagrams Specifications Photoelectric Sensors ESPE Rated operational volt. (U B ) From Sub module Rated …

Text truncated - open the document above for the full version.

WSS0001 Label and Position

Radio Test Report: TTR-001914WUS1 1 MPE Calculation OET Bulletin No. 65, Supplement C 01-01 47 CFR §§1.1307 and 2.1091 2.1091 Radio frequency radiation exposure evaluation: mobile devices. For purposes of these requirements mobile devices are defined by the FCC as transmitters designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimetres is normally maintained between radiating structures and the body of the user or nearby persons. These devices are normally evaluated for exposure potential with relation to the MPE limits. As the 20cm separation specified under FCC rules may not be achievable under normal operation of the EUT, an RF exposure calculation is needed to show the minimum distance required to be less than 1mW/cm 2 power density limit, as required under FCC rules. Prediction of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 where: S = power density R = distance to the centre of radiation of the antenna EIRP = EUT Maximum power Note: The EIRP measurement was performed using a signal substitution method. Result Main Controller Prediction Frequency (MHz) Maximum EIRP (mW) Power density limit (S) (mW/cm 2 ) Distance (R) cm required to be less than 1mW/cm 2 2444 MHZ0.510.2 cm 4 arranged-re 4 2 S EIRP R R EIRP S Radio Test Report: TTR-001914WUS1

Total number of pages : 67 TRaC Wireless Test Report:TTR-000729WUS2 Applicant:Carlo Gavazzi Group Apparatus:SubController Specification(s):CFR47 Part 15.247 July 10 th 2008 FCCID:Y55WSS0001 Purpose of Test: Certification Authorised by: : Radio ProductManager Issue Date:10 th February 2011 Authorised Copy Number: PDF Radio Test Report: TTR-000729WUS2 2 Contents Section 1:Introduction3 1.1General3 1.2Tests Requested By4 1.3Manufacturer4 1.4Apparatus Assessed4 1.5Test Result Summary5 1.6Notes Relating To The Assessment6 1.7Deviations from Test Standards6 Section 2:Measurement Uncertainty7 2.1Measurement Uncertainty7 Section 3:Modifications9 3.1Modifications Performed During Assessment9 Appendix A:Formal Emission Test Results10 A16 dB Bandwidth11 A2Transmitter Peak Output Power12 A3Transmitter Power Spectral Density13 A4RF Antenna Conducted Spurious Emissions14 A5Radiated Electric Field Emissions within the Restricted Bands of 15.20516 A6Antenna Gain21 A7Unintentional Radiated Electric Field Emissions - 15.10922 Appendix B:Supporting Graphical Data23 Appendix C: Additional Test and Sample Details56 Appendix D:Additional Information62 Appendix E:Calculation of the duty cycle correction factor63 Appendix F:Photographs and Figures64 Radio Test Report:TTR-000729WUS2 3 Section 1:Introduction 1.1General This report contains an assessment of an apparatus against Electromagnetic Compatibility Standards based upon tests carried out on samples submitted to the Laboratory. Test performed at:TRaC Telecoms & Radio[ ] Unit E South Orbital Trading Park Hedon Road Hull, HU9 1NJ. United Kingdom. Telephone:+44 (0) 1482 801801 Fax:+44 (0) 1482 801806 [X] TRaC Telecoms & Radio Unit 1, Pendle Place Skelmersdale, West Lancs, WN8 9PN, UK Telephone:+44 (0) 1695 556666 Fax:+44 (0) 1695577077 Email:[email protected] Web site:http://www.tracglobal.com Tests performed by:S Hodgkinson Report author:S Hodgkinson This report must not be reproduced except in full without prior written permission from TRaC Telecoms & Radio. Radio Test Report:TTR-000729WUS2 4 1.2Tests Requested By This testing in this report was requested by : Carlo Gavazzi Group Over Hadstenvej 40 8370 Hadsten DK-Denmark Telephone +45 89606292 1.3Manufacturer Carlo Gavazzi Group Over Hadstenvej 40 8370 Hadsten DK-Denmark Telephone +45 89606292 1.4Apparatus Assessed The following apparatus was assessed between19 th – 31 st January 2011 Subcontroller Unit Radio Test Report:TTR-000729WUS2 5 1.5Test Result Summary Full details of test results are contained within Appendix A. The following table summarises the results of the assessment. The statements relating to compliance with the standards below apply ONLY as qualified in the notes and deviations stated in sections 1.6 to 1.7 of this test report. Full details of test results are contained within Appendix A. The following table summarises the results of the assessment. Test TypeRegulation Measurement standard Result Radiated spurious emissions (Restricted bands) Title 47 of the CFR: Part 15 Subpart C; 15.247 ANSI C63.10Pass Conducted spurious emissions (Non-restricted bands) Title 47 of the CFR: Part 15 Subpart C; 15.247 ANSI C63.10Pass AC Power conducted emissions Title 47 of the CFR: Part 15 Subpart C; 15.207 ANSI C63.10N/A Occupied Bandwidth Title 47 of the CFR : Part 15 Subpart C; 15.247(a)(2) ANSI C63.10Pass Conducted Carrier Power Title 47 of the CFR : Part 15 Subpart C; 15.247(b) ANSI C63.10Pass Power Spectral Density Title 47 of the CFR : Part 15 Subpart C; 15.247(d) ANSI C63.10Pass Unintentional Radiated Spurious Emissions Title 47 of the CFR: Part 15 Subpart B; 15.109 ANSI C63.10Pass Digital Modulation Title 47 of the CFR: Part 15 Subpart C; 15.403 - RF Safety Title 47 of the CFR : Part 15 Subpart C; 15.247(b)(5) - Abbreviations used in the above table: Mod: Modification CFR: Code of Federal RegulationsANSI: American National Standards Institution REFE: Radiated Electric Field EmissionsPLCE: Power Line Conducted Emissions Radio Test Report:TTR-000729WUS2 6 1.6Notes Relating To The Assessment With regard to this assessment, the following points should be noted: The results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. The apparatus was set up and exercised using the configurations, modes of operation and arrangements defined in this report only. Particular operating modes, apparatus monitoring methods and performance criteria required by the standards tested to have been performed except where identified in Section 1.7 of this test report (Deviations from Test Standards). For emissions testing, throughout this test report, “Pass” indicatesthat the results for the sample as tested were below the specified limit (refer also to Section 2, Measurement Uncertainty). Where relevant, the apparatus was only assessed using the monitoring methods and susceptibility criteria defined in this report. All testing with the exception of testing at the Open Area Test Site was performed under the following environmental conditions: Temperature: 20to 20C Humidity : 45 to 48% All dates used in this report are in the format dd/mm/yy. This assessment has been performed in accordance with the requirements of ISO/IEC 17025. 1.7Deviations from Test Standards There were no deviations from the standards tested to. Radio Test Report:TTR-000729WUS2 7 Section 2:Measurement Uncertainty 2.1Measurement Uncertainty For the test data recorded in accordance with note (iii) of Section 2.1 the following measurement uncertainty was calculated : All statements of uncertainty are expanded standard uncertainty using a coverage factor of 1.96 to give a 95% confidence where no required test level exists. [1] Adjacent Channel Power Uncertainty in test result = 1.86dB [2] Carrier Power Uncertainty in test result (Equipment - TRLUH120) = 2.18dB Uncertainty in test result (Equipment – TRL05) = 1.08dB Uncertainty in test …

Text truncated - open the document above for the full version.

WSS0001 Test Setup Photos