Y5TV18GSM Mobile Phone

1 Introduction This manual has 3 sections: Section 1. Safety warnings and precautions Section 2. The phone is used to contact emergency services by pushing the 911 button, playing the radio, using the flashlight, and taking your blood pressure with the optional blood pressure meter. No cellular service included. Section 3 optional. You can purchase GSM cellular service to make cellular phone calls using the large numbers on the face of the cell phone, type text messages and text blood pressure readings to your family or doctors. Contact AlertUSA for low cost and simple Cellular service at 1- 800-403-9998 2 Included with the phone Accessories: 1* AC adapter to charge battery 1* Earphone 1* Battery 1* English User Manual Optional: Blood Pressure Meter for Purchase Table Of Contents Page 4 to 26 - Safety Warning and Precautions Page 27 - Load Battery and Charge plus Turn power on phone and turn power off the phone Page 28 - Use 911 button on back of phone to contact 911 emergency services Page 29 to 30 - How to use the FM Radio, Flashlight and Audio Player Page 31 - Schematic of Phone Layout, How to use the keys 3 Page 32 to 33 - top of 21 List of all the Phone Features Page 34 - How to setup Speed Dialing Page 35 to 36 - How to recall Missed calls/Dialed calls/Received calls and How to Text Message Page 37 to 39 - How to take Blood Pressure Readings Page 40 to 41 - Blood Pressure Classifications Page 42 - How to setup Voice Prompt for Key Green Number and when a call is being received Page 43 - How to use Hearing Aids with the Ear Pieces Page 43 - How to Use Settings to setup your phone, time and date for example Page 44 - How to Use Setting to setup User Profiles like Ring Tone Page 44 - How to Restore Factory Setting if Errors Occur 4 1 Safety warning and precautions Before you use this mobile phone, please read these precautions carefully so as to guarantee the safe and correct use of your phone. 1.1 Common précautions „ You can only use the battery and the battery discharge designated by our company for your mobile phone. If other products not designated are used, it may cause liquid leaking of the battery, overheating, explosion and fire. „ Please don’t strike, vibrate or throw the mobile phone so as to avoid failure of the phone or fire. 5 „ Please don’t put the mobile phone into the microwave oven or high-pressure equipment. Otherwise, it may cause the damage of the electric circuit, fire or other accidents. „ Please don’t use the mobile phone at the places with flammable and explosive gases. Otherwise, it may cause the failure of the mobile phone or fire. „ Please don’t put the mobile phone at the places with high temperature, high humidity or plenty of dust. Otherwise, it may cause the failure of the mobile phone. „ Please don’t put the mobile phone at the places within the reach of the children. 6 Otherwise, it may cause physical injury as the children take it as a toy. „ Please don’t put the mobile phone on the uneven or unstable surface so as to prevent it from falling, which may cause failure or damage. 1.2 Précautions for using the mobile phone „ Please shut off your mobile phone at the places where mobile phones are prohibited to use, such as in the airplane, hospital, etc. for the use of mobile phone may affect the normal work of the electronic equipment and medical instrument. If the mobile phone is used in such 7 places, you shall follow the related regulations stipulated for them. As the mobile phone has the function of automatic power-on, please check the setting of the alarming clock so as to make sure your mobile phone won’t be automatically powered on during the flying of the airplane. „ Please don’t use the mobile phone at places with weak signals or high-precision electronic equipment. The interference of the radio wave may cause the wrong operation and other problems of the electric equipment. Special attention shall be paid when the mobile phone is close to the following 8 equipment: hearing aid, pacemaker and other medical electronic equipment, fire detector, automatic gates and other automatic control devices. For the details over the affection on pacemaker and other medical electronic equipment, please make inquiries from the equipment’s manufacturer or the local distributor. „ Please don’t apply force on the LCD or use it to strike on other things. Otherwise, the LCD plate may be damaged or its liquid may be leaked. The liquid of the LCD goes into the eyes, it may cause ablepsia. In this case, you shall wash the eyes with clean water immediately 9 (never knead the eyes with hands) and go to the hospital for medical help. „ Please don’t disassemble or refit the mobile phone. Otherwise, it may cause the damage, electric leakage and circuit failure of the mobile phone. „ In few cases, the use of mobile phone in the vehicles of some models may cause improper influence to the electronic equipment. In such a case, please don’t use the mobile phone so as to guarantee the safety. „ Please don’t use the pin, end of the pen or other sharp articles to press the keys. Otherwise, it may cause physical injuries. 10 „ Please don’t use the mobile phone when its antenna is damaged. Otherwise, it may cause physical injuries. „ Please don’t make the mobile phone get close to the magnetic objects like the magnetic card as the radiation wave may delete the information stored in the floppy, store value card and credit card. „ Please keep the small metal articles like the drawing pin far from the phone receiver as the speaker can produce magnetism during work, which may suck small metal articles and thus cause the physical injury or the damage of the mobile phone. „ Please keep the mobile 11 phone from humidity as the water or other liquid will cause overheating, electricity leakage or failure if it goes into the mobile phone. 1.3 Précautions for using the battery „ Please don’t put the battery into the fire. Otherwise, the battery will get burned or explode. „ When loading the bat…

Text truncated - open the document above for the full version.

1850~1990MHz RF PA GLT2218 U605 ANTENNA RF tr ansceiver AD6548BCPZ U 602 RX T X Crystal 26M Hz Ba seband Processor MT6223D U100 Powe r management Backup battery Char ge circuit Mem ory Nor+psram U300 Moto r Keypad UART 32.7 68KHz Audio LCD FM U807 MIC Receiver Audi o PA Headset Spe aker 824~894MHz

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS EUT – Front View EUT – Rear View EUT – Battery Top View EUT – Battery Bottom View

EXHIBIT A - FCC ID LABELING AND LOCATION FCC ID Label FCC ID Label Location Label here The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS EUT – Battery off View EUT – Front Cover off View EUT – Rear Cover off View EUT – Main Board with LCD and Keyboard Top View EUT – Main Board with LCD Cover off Top View EUT – Main Board with Keyboard Cover Off Top View EUT – Main Board Bottom View EUT – Antennas View GSM Antenna

Operational description and technical overview for V18 The device adopts the MTK`s chipset which includes MT6223DA and AD6548BCPZ. The MT6223DA is an entry level chipset solution with class 10 GSM modem. MT6223DA is our first 2.5G system-on-chip, integrating all essential electronic components, including DBB, ABB, power management unit。It integrates not only analog baseband but also power management blocks into one chip and can greatly reduce the component count. Besides, MT6223DA is capable of SAIC (Single Antenna Interference Cancellation) and AMR speech. Based on 32 bit ARM7EJ-S TM RISC processor, MT6223DA provides an unprecedented platform for high quality modem performance. It also integrates some power management function on the chip and D/A converter for applications like MP3 music and an audio power amplifier for hands-free speakerphone operation. The GSM RF part includes two main components AD6548BCPZ and GLT2218. The AD6548BCPZ is a quadruple band transceiver IC suitable for GSM 850, PCS1900 class 12 applications. The GLT2218 is a quad band power amplifier module designed to support quad band applications. The Memory used is NOR+PSRAM(128Mb+32Mb) Keypad keys are another user interface. There are SIX WHITE LEDs under the keypad to work as keypad backlight. In the audio process and amplify part, all analog audio signals from or to ABB, GSM module is processed. This part contains an audio power amplifier, several analog multiplexers/switches and operation amplifiers. The machine is configured a Micro SD connector which can support up to 2GB micro SD car

Item ReferenceValue 1 PCBMainBoard PCB Bead 75 Bead 80 BEAD 180 BEAD 120 4 L600,C631,C821 22pF 5 C129,T221,T222,C601 1nF 6 C103,C104,C105,C106,C107,C 108,C110,C111,C113,C131,C2 00,C203,C208,C210,C221,C30 2,C424,C617,C640,C641,C648 ,C649,C650,C651,C654,C655, C824,C825,C914 0.1uF 7 C114,C116,C120,C123,C125,C 130 4.7u (0603) 8 C118,C122,C124,C132,C300,C 504,C820 1uF (0402) 9 T210,T211,C216,C223,C232,C 233,C237,C240,C244,C246,C4 28,C618,C636,C637 33pF 10 C217,C500,C501 1uF (0603) 11 C202,C206 10uF (0805) 12 C133,C201,C215,C429,C658 22u (0805) 13 C218,C502,C503 2.2u (0603) 14 C605,C616,C621,C623 5.6p 100nH Substitution 16 C638 0.5p 17 C656 1pF 18 C427 1.5pF 19 C633,C639,C661,C662 6.8p 20 C600,C603 82p 21 C642,C643 39p 22 C644 47pF 23 C204,C211,C234,C235,C245 100p B100,B214,B215 15 C624,B802 C800_MAINBOARD_V3.0 3 B200,B201,B202,B203,B204,B 207,L803 2 24 C602,C826 220p 25 L615 12pF 26 C101,C10215p 27 C630,C632,C663,C665 18pF 28 C619 10nF 29 C823 22n 30 C660 33n 31 C112 47n D200 Diode Substitution Substitution Substitution 31 D250,D251,D252,D253,D254,D 255,D256,D257 red light 32 J402 6.8mm Battery Connectors 33 J400usb 5 pin pillared 34 J200 EAR JACK Φ3.mm 6Pin H=4.10 2.5MM 35 J403 SIM card Connectors 36 SD300 T-FLASH cassette 37 S200,S201 TACT Switch Substitution 38 S203,S204,S205 3 pin toggle switch Substitution 39 L612 4.7nH C635 1.2nH Substitution L604 3.3nH Substitution 42 L609 3.9nH 43 C657 10nH 44 L611 15nH 32 40 41 45 L617 22nH 46 R100,R101,R102,R103,R111,R 420,R421,R607,C620,C822 0 47 R119 0.20 (1% 0805) 48 R605 10 49 R213,R214 12 50 R614 51 51 R108 6.8 52 R223,R224,R500 30 53 L601,L603 82 54 R216,R217 180 55 R612,R613,R617,R618 2.2K 56 R112 3.9K 57 R202,R204,R207,R219,R222,R 610,R611,R615,R620 1K 58 R203,R205,R206 1.5K 59 R300,R301,R305,R310,R311,R 313,R601,R800,R801 10k 60 R210 24K 1% 61 R115,R209 47K 62 R211 75K 63 R212,R221 100k 64 U100 BB IC U102 PMOS with schottky Substitution 66 U202 Audio PA Substitution Substitution Substitution 67 U300 MCP 68 U602 RF Transceiver 69 U605 PA RF Xtal 26MHz 65 Substitution Substitution Substitution 71 U807 FM Radio Xtal 32K Substitution 73 Z602 RX GSM&DCS SAW PCS1900 RX SAW Substitution Substitution Substitution Substitution Z601 GSM850 RX SAW Substitution Substitution 76 S1C800 V3 RF-shielding U604 X100 70 Z604 74 72 75 Date：20100104 Part NumberDescriptionQuantity C800_MAINBOARD_V3.0C800_MAINBOARD_V3.0, 4F R4 PCB1 BLM15BB750SN1DBead 0402 75+/-25% 300mA 0.4ohm RoHS MGGB1005M800HT-LFBead 0402 80+/-25% 200mA 0.3ohm RoHS BLM18PG181SN1DBead 0603 180+/-25% 1.5A 0.09ohm RoHS MGLB1608M121T-LFBead 0603 120+/-25% 1.2A 0.1ohm RoHS GRM1555C1H220JZ01DC 22p 50V J 0402 C0G RoHS 3 GRM155R71H102KA01DC 1n 50V K 0402 X7R RoHS4 GRM155R61A104KZ01DC 0.1u 10V K 0402 X5R RoHS29 GRM188R60J475KE19C 4.7u 6.3V K 0603 X5R RoHS6 GRM155R61A105KZ01DC 1u 10V K 0402 X5R RoHS7 GRM1555C1H330JZ01DC 33p 50V J 0402 C0G RoHS14 GRM188R61C105KE01DC 1uF 16V K 0603 X5R RoHS3 GRM21BR60J106ME01DC 10uF 6.3V M 0805 X5R RoHS2 GRM21BF50J226ME39LC 22u 6.3V M 0805 Y5V RoHS5 GRM188R61C225KE01DC 2.2u 16V K 0603 X5R RoHS3 GRM1555C1H5R6CZ01CC 5.6p 50V D 0402 C0G RoHS4 LQG15HSR10J02L 100nH 5% 0402 RoHS MGCI1005TR10JT-LFL 100nH 5% 0402 RoHS GRM1555C1HR50CZ01DC 0.5p 50V C 0402 C0G RoHS1 GRM1555C1H1R0CZ01DC 1pF 50V C 0402 C0G RoHS1 GRM1555C1H1R5CZ01DC 1.5pF 50V C 0402 C0G RoHS1 GRM1555C1H6R8CZ01DC 6.8p 50V C 0402 C0G RoHS4 GRM1555C1H820JZ01DC 82p 50V J 0402 C0G RoHS2 GRM1555C1H390JZ01DC 39p 50V C 0402 C0G RoHS2 GRM1555C1H470JA01DC 47pF 50V J 0402 C0G RoHS1 GRM1555C1H101JD01DC 100p 50V J 0402 C0G RoHS5 7 2 3 GRM1555C1H221JA01DC 220p 50V J 0402 C0G RoHS2 GRM1555C1H12R02CZ01DC 12pF 50V D 0402 C0G RoHS1 GRM1555C1H15R02CZ01DC 15pF 50V D 0402 C0G RoHS2 GRM1555C1H180JA01DC 18pF 50V J 0402 C0G RoHS4 GRM155R71E103KA01DC 10n 25V K 0402 X7R RoHS1 GRM155R71E223KA01DC 22n 25V K 0402 X7R RoHS1 GRM155R71E333KA01DC 33n 25V K 0402 X7R RoHS1 GRM155R71A473KA01DC 47nF 10V K 0402 X7R RoHS1 RB520S-30Diode SOD-523 30V 0.2A lead free 1SS420Diode SOD-523 30V 0.2A lead free CH521S-30PTDiode SOD-523,30V,0.2A lead free SDM20U30Diode SOD-523 30V 0.2A lead free BL-HUB36G-AV-TRB0603 SMD,H=0.4mm,MAX 25mA,,RoHS8 BT037-53006F2*21 USM01-055043F0*2 1 PJH05-600100BA081 MSI04-021861F2*21 MTF01-2323F-232221 ST-1186SE SKRELGE010 SS-1290 ssss811101 MGCI1005T4N7ST-LFL 4.7nH S 0402 RoHS1 SDCL1005C1N2STL 1.2nH S 0402 RoHS MGCI1005T1N2ST-LFL 1.2nH S 0402 RoHS SDCL1005C3N3STL 3.3nH S 0402 RoHS MGCI1005T3N3ST-LFL 3.3nH S 0402 RoHS SDCL1005C3N9STFL 3.9nH S 0402 RoHS1 MGCI1005T10NJT-LFL 10nH 5% 0402 RoHS1 MGCI1005T15NJT-LFL 15nH 5% 0402 RoHS1 1 2 3 1 1 MGCI1005T22NJT-LFL 22nH 5% 0402 RoHS1 RC0402JR-07 0RR 0 J 1/16W 0402 RoHS10 RL0805FR-07 0R2R 0.2 F 1% 1/8W 0805,RoHS1 RC0402JR-07 10RR 10 J 1/16W 0402 RoHS1 RC0402JR-07 12RR 12 J 1/16W 0402 RoHS2 RC0402JR-07 51RLR 51 J 1/16W 0402 RoHS1 RC0603JR-07 6R8R 6.8 J 1/8W 0603 RoHS1 RC0402JR-07 30RLR 30 J 1/16W 0402 RoHS3 RC0402JR-07 82RLR 82 J 1/16W 0402 RoHS2 RC0402JR-07 180RR 180 J 1/16W 0402 RoHS2 RC0402JR-07 2K2R 2.2K 1/16W 0402 RoHS4 RC0402JR-07 3K9R 3.9K J 1/16W 0402 RoHS1 RC0402JR-07 1KR 1K J 1/16W 0402 RoHS9 RC0402JR-07 1K5R 1.5K 1/16W 0402 RoHS3 RC0402JR-07 10KR 10K J 1/16W 0402 RoHS9 RC0402FR-07 24KR 24K F 1/16W 0402 RoHS1 RC0402JR-07 47KR 47K J 1/16W 0402 RoHS2 RC0402JR-07 75KR 75K J 1/16W 0402 RoHS1 RC0402JR-07 100KR 100K J 1/16W 0402 RoHS2 MT6223DA-LBB IC,9mmx9mm 224-TFBGA pb-free1 SI5853DC PMOS with schottky,1208-8 chipFET Lead-free MF5853C PMOS with schottky,1208-8 chipFET Lead-free EMA1901-50WL09GRR9-ball micro SMD,pitch=0.5mm,pb-free CP2290ITLX 9-ball micro SMD,pitch=0.5mm,pb-free SUP2990C-3TR 9-ball micro SMD,pitch=0.5mm,pb-free BL6212CP 9-ball micro SMD,pitch=0.5mm,pb-free K5L6331CAM/CAA-D270NOR+Utram,2.8V,64M+32M,56FBGA,pb-free1 AD6548BCPZ RF Transceiver, GSM850/E- GSM900/DCS1800/PCS1900,5x5mm LFCSP-32,pb-free 1 GLT2218 Dual-band GSM/GPRS Power Amplifier + Switch Module ,6mm*8mm 1 7M2600001826MHz Crystal 3.2x2.5mm Cl=11pF pb-free 1 1 SQ3D02600L2LNA26MHz Crystal 3.2x2.5mm Cl=11.2pF pb-free X1E0…

Text truncated - open the document above for the full version.

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. (Shenzhen). This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, NIST, or any agency of the Federal Government. * This report contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “★” (Rev. SAR EVALUATION REPORT For Shenzhen Qing Xin Electronic Technology Co., Ltd. 309#,3rd Floor,Blok A,HuaKang Building No.109 Zhenxing West Road, Futian, Shenzhen, Guangdong, China FCC ID: Y5TV18 Report Type: Original Report Product Type: Mobile Phone Test Engineer: Cabin Hu Report Number: RSZ11011951-SAR Report Date: 2011-01-27 Reviewed By: William Chen EMC Engineer Prepared By: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 Shenzhen Qing Xin Electronic Technology Co., Ltd. FCC ID: Y5TV18 Report No.: RSZ11011951-SAR Page 2 of 100 SAR Evaluation Report Summary of Test Results Rule Part(s): CFR 47 §2.1093 Test Procedure(s): FCC OET Bulletin 65C IEEE 1528-2003 Device Type: Portable device Exposure Category Population/Uncontrolled Modulation: GMSK TX Frequency Range: 824-849 MHz (Cellular Band) 1850-1910 MHz (PCS Band) Maximum Conducted Power Tested: Cellular Band: 32.25 dBm PCS Band: 30.78 dBm Antenna Type(s): Internal Antenna Body-Worn Accessories: Headset Face-Head Accessories: None Battery Type(s) Tested: 3.7VDC/1000mAh Rechargeable Battery Max. SAR Level(s) Measured: 0.289 W/Kg, 1g Head Tissue (Cellular Band) 0.273 W/Kg, 1g Body Tissue (Cellular Band) 0.270 W/Kg, 1g Head Tissue (PCS Band) 0.171 W/Kg, 1g Body Tissue (PCS Band) This wireless device has been shown to be capable of compliance for localized specific absorption rate (SAR) for General Population/Uncontrolled Exposure limits specified in ANSI/IEEE Standards and has been tested in accordance with the measurement procedures specified in FCC OET 65 Supplement C and IEEE 1528-2003. The results and statements contained in this report pertain only to the device(s) evaluated. EUT Photo Shenzhen Qing Xin Electronic Technology Co., Ltd. FCC ID: Y5TV18 Report No.: RSZ11011951-SAR Page 3 of 100 SAR Evaluation Report DOCUMENT REVISION HISTORY Revision Number Report Number Description of Revision Date of Revision 0 RSZ11011951-SAR Original Report 2011-01-27 Shenzhen Qing Xin Electronic Technology Co., Ltd. FCC ID: Y5TV18 Report No.: RSZ11011951-SAR Page 4 of 100 SAR Evaluation Report TABLE OF CONTENTS REFERENCE, STANDARDS AND GUILDELINES ......................................................................................... 5 SAR LIMITS.......................................................................................................................................................... 6 EUT DESCRIPTION ............................................................................................................................................. 7 TECHNICAL SPECIFICATION.................................................................................................................................. 7 FACILITIES AND ACCREDITATION .............................................................................................................. 8 DESCRIPTION OF TEST SYSTEM ................................................................................................................... 9 EQUIPMENT LIST AND CALIBRATION ...................................................................................................... 16 EQUIPMENTS LIST & CALIBRATION INFO............................................................................................................ 16 SAR MEASUREMENT SYSTEM VERIFICATION ....................................................................................... 17 LIQUID VERIFICATION......................................................................................................................................... 17 SYSTEM ACCURACY VERIFICATION.................................................................................................................... 20 EUT TEST STRATEGY AND METHODOLOGY .......................................................................................... 21 TEST POSITIONS FOR DEVICE OPERATING NEXT TO A PERSON’S EAR................................................................. 21 CHEEK/TOUCH POSITION.................................................................................................................................... 22 EAR/TILT POSITION............................................................................................................................................. 22 TEST POSITIONS FOR BODY-WORN AND OTHER CONFIGURATIONS....................................................................... 23 SAR EVALUATION PROCEDURE.......................................................................................................................... 24 SAR MEASUREMENT RESULTS .................................................................................................................... 25 SAR TEST DATA................................................................................................................................................. 25 APPENDIX A – MEASUREMENT UNCERTAINTY ..................................................................................... 27 APPENDIX B – PROBE CALIBRATION CERTIFICATES .......................................................................... 28 APPENDIX C – DIPOLE CALIBRATION CERTIFICATES ........................................................................ 68 APPENDIX D – SAR SYSTEM VALIDATION DATA .......................................................................…

Text truncated - open the document above for the full version.

11 22 33 44 55 66 77 88 99 1010 H H G G F F E E D D C C B B A A EA1 EA5 EA3 EA10 EA14 EA12 EA9 EA11 EA16 EA21 EA15 EA17 EA13 EA18 EA19 EA20 EA6 EA7 EA8 ED5 ED1 ED0 ED8 ED4 ED3 ED2 ED6 ED9 ED12 ED11 ED10 ED15 ED14 ED13 EA4 EA2 ED7 EA22 VBAT URXD1 4 UTXD1 4 PWRKEY 2,3 /SYSRST 2 /ELB 4/ECS0_FLASH 4/EUB 4/ERD 4/ECS1_PSRAM 4/EWR 4 ED[0..15] 4 UTXD1 4URXD1 4 PA_EN 6 SCLK 6 SDATA 6 LE 6 26MHz 6 KROW0 3 GPIO24_OP_EN 3 KROW3 3KROW2 3KROW4 3KROW1 3KCOL0 3KCOL1 3KCOL2 3KCOL3 3KCOL4 3 VBAT 2,3,4,5,6 EA[1..22] 4 VCXOEN 6 EINT0_HANDSET 3 BANDSW_DCS 6 /WATCHDOG 4 EA23 4 /EADV 4 ECLK 4 EWAIT 4 BT_UTXD3BT_URXD3 GPIO45_SCL_CAM/FM 7GPIO46_SDA_CAM/FM 7 CP_EINT1 GPIO25_MAIN_LCM_BL_PWM GPIO51_UTXD2 4 EINT3_CLAMSHELL XEN_OUT XEN_OUT_EINT2 GPIO15_TF_CLK 4GPIO17_CMD 4GPIO16_TF_D0 4GPIO18_TF_D3 4 EINT4_FM_GPIO26 3 EINT5_KeyLock_GPIO27 3 GPIO49_URXD2 4 GPIO22_FM_32K 7 LDC_CS 5 LCD_SCL 5LCD_SDA 5 LDC_REST 5 LDC_R/S 5 LCD_SCL 5LCD_SDA 5LDC_R/S 5 TitleSize Document Number Rev Date: Sheet of Audio,Keypad MT6223D A3 15 Friday, September 03, 2010 TitleSize Document Number Rev Date: Sheet of Audio,Keypad MT6223D A3 15 Friday, September 03, 2010 TitleSize Document Number Rev Date: Sheet of Audio,Keypad MT6223D A3 15 Friday, September 03, 2010 2.0.0 FIDUCIAL DOWNLOAD PORT BPI BUS EMI INTERFACE LCD INTERFACE UART kEYPAD EINT JTAG External memory interface C10115pC10115p F102F102 R106 nc R106 nc U100A MT6223P_13 U100A MT6223P_13 SYSCLK U1 XOUT 23 A10 XIN 23 A11 TESTMODE J10 GPIO26/EINT4/JTRST R8 JTCK U9 GPIO27/EINT5/JTDI P8 GPIO28/EINT6/JTMS T9 JTDO R9 JRTCK U8 BPI_BUS0 R2 BPI_BUS1 T2 BPI_BUS2 R3 BPI_BUS3 U3 BPI_BUS4 T3 BPI_BUS5 P3 BPI_BUS6/GPIO20 R4 BPI_BUS7/GPIO21/CLKO0 T4 BPI_BUS8/GPIO22/COL5/CLKO1 U4 BPI_BUS9/GPIO23/BSI_CS1/CLKO2 U5 BSI_CS0 T5 BSI_DATA R5 BSI_CLK U6 PWM/GPIO25 P7 SRCLKENA 23 A16 KCOL4 A15 KCOL3 B15 KCOL2 A14 KCOL1 B14 KCOL0 A13 KROW4 B13 KROW3 C13 KROW2 A12 KROW1 B12 KROW0 C12 EINT0 D12 EINT1 B11 GPIO42/BT/MFIQ/EINT2 C11 GPIO43/BE/MIRQ/EINT3 D11 EA0/GPIO30 J16 EA1 J15 EA2 J14 EA3 H17 EA4 H16 EA5 H15 EA6 G17 EA7 G16 EA8 G15 EA9 F17 EA10 F16 EA11 F15 EA12 E17 EA13 E16 EA14 E15 EA15 E14 EA16 D17 EA17 D16 EA18 D15 EA19 D14 EA20 C17 EA21 C16 EA22 C14 EA23 B17 EA24 B16 /EADV U15 ECLK U16 /ECS3 K15 /ECS2 K16 /ECS1 K17 /ECS0 L14 /EWR L15 /ERD L16 /EUB J17 /ELB K14 ED0 T16 ED1 U17 ED2 T17 ED3 P14 ED4 R16 ED5 R17 ED6 P17 ED7 P16 ED8 P15 ED9 N17 ED10 N16 ED11 N15 ED12 M17 ED13 M16 ED14 M15 ED15 L17 WATCHDOG/GPIO29 T14 LSCK/LCD_D0 T13 LCD_RSTB T12 LCD_WRB R12 LCD_A0 R13 LSCE0/LCD_CS0B R14 LSCE1/LCD_CS1B/GPIO14/EINT7 U14 UTXD2/GPIO51 D8 URXD2/CLK5/GPIO49 C8 URXD3/CLK4/GPIO48 B9 UTXD3/CLK3/GPIO47 A9 URTS1/SDA/GPIO46 C9 UCTS1/SCL/GPIO45 D10 UTXD1/GPIO44 C10 URXD1/GPIO50 C7 DAICLK/EDICK/GPIO15 T6 DAIPCMOUT/EDIDAT/GPIO16 U7 DAIPCMIN/GPIO17 T7 DAIRST/GPIO18 R6 DAISYNC/EDIWS/GPIO19 P6 SRCLKENAI/GPIO31 23 A17 ALERTER/GPIO24 R7 LSDA/LCD_D1 U12 LSA0/LCD_D2 R11 LCD_D3 T11 LCD_D4 U11 LCD_D5 U10 LSA0LCD_D6 P10 LSDA/LCD_D7 R10 LSCK/LCD_D8 T10 EWAIT T15 EA25/ECRE P13 LCD_RD U13 /SYSRST T8 R103 0 R103 0 TP101TP101 R105 nc R105 nc X100 32.768K X100 32.768K 14 3 2 C10215pC10215p F101F101 R104 nc R104 nc TP103TP103 F100F100 R102 0 R102 0 TP105TP105 TP102TP102 F103F103 TP104TP104 R101 0 R101 0 11 22 33 44 55 66 77 88 99 1010 H H G G F F E E D D C C B B A A VREFN VREFP AVDD_RTC AFC_BYP MICBIASPMICBIASN AVDD VDD VMEM VRF_23 VDD VDD VBAT VCORE VCOREAVDDVDDVMEM VSIM VBAT VBAT VCHG VBAT VBAT VCTXO VCHG SPKP0 3 SPKN0 3 MICN0 3 MICP0 3 MICP1 3 MICN1 3 IB 6 I6QB 6 Q6 VAFC 6 VAPC 6 MP3_OUTL 3 PWRKEY 1,3/SYSRST 1 MT6223_SIM_CLK 4 MT6223_SIM_RST 4 MT6223_SIM_IO 4 AVDD 3,7 VDD 3,4,5,6 VMEM 4 VCORE VBAT 1,3,4,5,6 VSIM 4 VBAT 1,3,4,5,6 VDD 3,4,5,6 VRF_23 6 VCORE VDD 3,4,5,6 AVDD 3,7 VMEM 4 MICBIASP 3 MICBIASN 3 VBAT 1,3,4,5,6 VBAT 1,3,4,5,6 VCHG VIB MP3_OUTR 3 FM_INL 7 FM_INR 7 VBAT 1,3,4,5,6 VIB ADC1_MIC 3 VDD 3,4,5,6 VCTXO VCHG LED_K 5 LED_R_B 3 TitleSize Document Number Rev Date: Sheet of <Doc> 2.0.0 MT6223D A3 25 Friday, September 03, 2010 TitleSize Document Number Rev Date: Sheet of <Doc> 2.0.0 MT6223D A3 25 Friday, September 03, 2010 TitleSize Document Number Rev Date: Sheet of <Doc> 2.0.0 MT6223D A3 25 Friday, September 03, 2010 TO CHRINTO GATEDRV C107 0.1u C107 0.1u 4.7uC1144.7uC114 R110ncR110nc C131 0.1u C131 0.1u C130 4.7u C130 4.7u 12 C1204.7uC1204.7u U102 SI5853DC U102 SI5853DC A 1 A1 2 K1 7 K 8 S 3 G 4 D 5 D1 6 R1190.2R1190.2 C122 1u 0402C122 1u 0402 R111 0R111 0 J408DC_JACKJ408DC_JACK 2 1 C1321u 0402C1321u 0402 R11547KR11547K C1130.1uC1130.1u C1080.1uC1080.1u U100D MT6223P_13 U100D MT6223P_13 BATDET C5 BATSENSE A4 ISENSE B4 VCTXO E2 VIO B7 VBAT2 B3 VCORE A7 VRF_SENSE B8 VRF A8 AVBATRF A3 VBAT1 A2 RSTCAP D2 VBAT3 B2 VM B6 VSIM A5 SIMIO B5 SIMRST C6 SIMCLK D6 VMSEL E4 PWRKEY D3 LED D4 BAT_BK D7 VREF B1 VA C1 CHRIN D5 GATEDRV C4 LED_B G10 LED_G G9 LED_R H8 VIB G8 AVBAT A1 RESET C2 + C13322u + C13322u 4.7uC1164.7uC116 C1110.1uC1110.1u 4.7uC1254.7uC125 R100 0 R100 0 C104 0.1u C104 0.1u R113 ncR113 nc C110 0.1u C110 0.1u C129 1n C129 1n C118 1u 0402 C118 1u 0402 R1123.9KR1123.9K U100C MT6223P_13 U100C MT6223P_13 AFC R1 AFC_BYP P2 AU_MOUTL F2 AU_MOUTR F1 AU_FMINL F3 AU_FMINR E3 AU_OUT0_N G1 AU_OUT0_P G2 AU_MICBIAS_P G3 AU_MICBIAS_N H2 AU_VREF_N H3 AU_VREF_P H4 AU_VIN0_P J1 AU_VIN0_N J2 AU_VIN1_N K1 AU_VIN1_P K2 QP L1 QN L2 IN L3 IP L4 APC N1 AUXADC0 M2 AUXADC1 M3 AUXADC2 N2 R108 6.8 R108 6.8 4.7uC1234.7uC123 C1060.1uC1060.1u C103 0.1u C103 0.1u B100 Bead 120 B100 Bead 120 A - + V101 nc A - + V101 nc 1 2 C105 0.1u C105 0.1u C11247nC11247n U100B MT6223P_13 U100B MT6223P_13 VDD33_EMI5 F14 VDD33_EMI4 G14 VDD33_EMI3 M14 VDD33_EMI2 N14 AVDD_RTC B10 AVSS_PLL T1 VDDK2 P9 VDD33_EMI1 P12 VDDK1 N4 VDD33_LCD P11 VDD333 D13 AGND_RF A6 VSS33_EMI1 L9 VDD332 P5 VDD331 P4 VSS33_EMI2 K9 AVDD_MBU F4 AVSS_MBUF G4 AVDD_AFE E1 AGND_AFE H1 AGND D1 DGND4 H7 AVSS_GSMRFTX M1 AVDD_GSMRFTX J4 AVSS_RFE P1 AVDD_REF K4 AUX_REF N3 VSS33_EMI5 K11 VDDK3 H14 VDDK4 D9 VSS331 J7 VSS332 K7 VSS333 L8 VSS334 K8 VSS335 J11 DGND1 H9 DGND2 H10 VSS33_EMI3 L10 VSS33_EMI4 K10 DGND3 H11 A…

Text truncated - open the document above for the full version.

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, NIST, or any agency of the Federal Government. * This report contains data that are not covered by the NVLAP accreditation and are marked with an asterisk “★” (Rev.2) FCC PART 22H, 24E MEASUREMENT AND TEST REPORT For Shenzhen Qing Xin Electronic Technology Co., Ltd. 309#, 3rd Floor, Blok A, HuaKang Building, No.109 Zhenxing West Road, Futian, Shenzhen, Guangdong, China FCC ID: Y5TV18 Report Type: Original Report Product Type: GSM Mobile phone Test Engineer: Wayne Cheng Report Number: RSZ11011951-22H&24E Report Date: 2011-01-25 Reviewed By: Merry Zhao EMC Engineer Prepared By: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 Shenzhen Qing Xin Electronic Technology Co., Ltd. FCC ID: Y5TV18 Report No.: RSZ11011951-22H&24E Page 2 of 31 FCC Part 22H/24E Test Report TABLE OF CONTENTS GENERAL INFORMATION.......................................................................................................................................4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................4 OBJECTIVE...................................................................................................................................................................4 RELATED SUBMITTAL(S)/GRANT(S).............................................................................................................................4 TEST METHODOLOGY..................................................................................................................................................4 TEST FACILITY.............................................................................................................................................................5 SYSTEM TEST CONFIGURATION ..........................................................................................................................6 JUSTIFICATION.............................................................................................................................................................6 EQUIPMENT MODIFICATIONS.......................................................................................................................................6 CONFIGURATION OF TEST SETUP.................................................................................................................................6 BLOCK DIAGRAM OF TEST SETUP................................................................................................................................6 SUMMARY OF TEST RESULTS ...............................................................................................................................7 FCC §1.1307 & §2.1093 - RF EXPOSURE INFORMATION ...................................................................................8 APPLICABLE STANDARD....................................................................................…

Text truncated - open the document above for the full version.