Y7YT0035G01Wireless Clamp Meter

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation. Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

ETC Report No. : 10-12-RBF-150-01 Sheet 1 of 8 Sheets FCC ID.: Y7YT0035G01 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT 1. Total View of EUT 2. Top View of EUT ETC Report No. : 10-12-RBF-150-01 Sheet 2 of 8 Sheets FCC ID.: Y7YT0035G01 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT 3. Side View of EUT 4. Front View of EUT ETC Report No. : 10-12-RBF-150-01 Sheet 3 of 8 Sheets FCC ID.: Y7YT0035G01 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT 5. Side View of EUT 6. Rear View of EUT ETC Report No. : 10-12-RBF-150-01 Sheet 4 of 8 Sheets FCC ID.: Y7YT0035G01 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT 7. Bottom View of EUT

910805 1 LABEL 10mm 15mm FCC ID:Y7YT0035G01 Model: 35

ETC Report No. : 10-12-RBF-150-01 Sheet 5 of 8 Sheets FCC ID.: Y7YT0035G01 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT 8. Internal View of EUT ETC Report No. : 10-12-RBF-150-01 Sheet 6 of 8 Sheets FCC ID.: Y7YT0035G01 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT 9. Component View of PCB 10. Solder View of PCB ETC Report No. : 10-12-RBF-150-01 Sheet 7 of 8 Sheets FCC ID.: Y7YT0035G01 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT 11. Component View of PCB 12. Solder View of PCB ETC Report No. : 10-12-RBF-150-01 Sheet 8 of 8 Sheets FCC ID.: Y7YT0035G01 Rev. No 1.0 CONSTRUCTED PHOTOS of EUT 13. Display module 14. Display module

Rev. No 1.0 FCC Part 15 EMI TEST REPORT of E.U.T. ： Wireless Clamp Meter FCC ID ： Y7YT0035G01 MODEL ： 35 for APPLICANT : DER EE Electrical Instrument Co. Ltd. ADDRESS : 7F-2, No. 351, Sec2, Zhongshan Rd, Zhonghe Dist., New Taipei City 235, Taiwan Test Performed by ELECTRONICS TESTING CENTER, TAIWAN NO.34, LIN 5, DINGFU TSUEN, LINKOU SHIANG TAIPEI COUNTY, TAIWAN, 24442, R.O.C. Tel : (02)26023052 Fax : (02)26010910 http://www.etc.org.tw ; e-mail: [email protected] Report Number : 10-12-RBF-150-01 ETC Report No. : 10-12-RBF-150-01 FCC ID. : Y7YT0035G01 Rev. No 1.0 TEST REPORT CERTIFICATION Applicant : DER EE Electrical Instrument Co. Ltd. 7F-2, No. 351, Sec2, Zhongshan Rd, Zhonghe Dist., New Taipei City 235, Taiwan Manufacturer : DER EE Electrical Instrument Co. Ltd. 7F-2, No. 351, Sec2, Zhongshan Rd, Zhonghe Dist., New Taipei City 235, Taiwan Description of EUT : a) Type of EUT : Wireless Clamp Meter b) Trade Name : DER EE c) Model No. : 35 d) Power Supply : DC 1.5V Battery *2 e) Frequency Range : 910MHz Regulation Applied : FCC Rules and Regulations Part 15 Subpart C (2009) I HEREBY CERTIFY THAT: The data shown in this report were made in accordance with the procedures given in ANSI C63.4 (2003), and the energy emitted by the device was founded to be within the limits applicable. I assume full responsibility for accuracy and completeness of these data. Note: 1. The result of the testing report relate only to the item tested. 2. The testing report shall not be reproduced expect in full, without the written approval of ETC. ETC Report No. : 10-12-RBF-150-01 FCC ID. : Y7YT0035G01 Rev. No 1.0 Issued Date : Feb. 24, 2011 Test Engineer : ( Vincent Chang , Engineer ) Check By : ( Charles Wang, Supervisor ) Approve & Authorized Signer : Will Yauo, Manager EMC Dept. II of ELECTRONICS TESTING CENTER, TAIWAN ETC Report No. : 10-12-RBF-150-01 FCC ID. : Y7YT0035G01 Rev. No 1.0 Table of Contents Page 1 GENERAL INFORMATION ....................................................................................................... 1 1.1 Product Description...................................................................................................................... 1 1.2 Characteristics of Device .............................................................................................................. 1 1.3 Test Methodology......................................................................................................................... 1 1.4 Test Facility.................................................................................................................................. 1 2 PROVISIONS APPLICABLE...................................................................................................... 2 2.1 Definition ..................................................................................................................................... 2 2.2 Requirement for Compliance ....................................................................................................... 3 2.3 Restricted Bands of Operation ..................................................................................................... 5 2.4 Labeling Requirement .................................................................................................................. 5 2.5 User Information .......................................................................................................................... 6 3 SYSTEM TEST CONFIGURATION .......................................................................................... 7 3.1 Justification .................................................................................................................................. 7 3.2 Devices for Tested System ........................................................................................................... 7 4 RADIATED EMISSION MEASUREMENT .............................................................................. 8 4.1 Applicable Standard ..................................................................................................................... 8 4.2 Measurement Procedure ............................................................................................................... 8 4.3 Measuring Instrument................................................................................................................. 11 4.4 Radiated Emission Data ............................................................................................................. 12 4.5 Field Strength Calculation.......................................................................................................... 14 4.6 Photos of Radiation Measuring Setup ........................................................................................ 15 5 CONDUCTED EMISSION MEASUREMENT........................................................................ 16 5.1 Description ................................................................................................................................. 16 6 ANTENNA REQUIREMENT .................................................................................................... 17 6.1 Standard Applicable ................................................................................................................... 17 6.2 Antenna Construction................................................................................................................. 17 7 BAND EDGES MEASUREMENT............................................................................................. 18 7.1 Standard Applicable ................................................................................................................... 18 7.2 Measurement Procedure ............................................................................................................. 18 7.3 Measurement Equipment............................................................................…

Text truncated - open the document above for the full version.

ETC Report No. : 10-12-RBF-150-01 Sheet 16 of 21 Sheets FCC ID.: Y7YT0035G01 Rev. No 1.0 4.6 Photos of Radiation Measuring Setup