YCR-AR-SWR-3CAIR SWIMMERS SHARK & AIR SWIMMERS CLOWN FISH & AIR SWIMMERS-PIRANHA & AIR SWIMMERS-KILLER WHALE

Contents of Air Swimmers Killer Whale Box 1 x Air Swimmers Killer Whale balloon 1 x Tail fin 1 x Tail motor unit 2 x AA batteries 3 x Elastic bands 4 x Double sided sticky pads 1 x Pod1 x Controller 1 x Putty holder Spare part included: 1 x Elastic band 1 x Putty 4 x Clear tape tabs 4.5. 7. 8. 9. 11. 12.13.14. 10. 6. 1 x AAA battery 1. To fill the Air Swimmer with helium, lay the Air Swimmer balloon (1) out flat on the ground and insert the helium tank nozzle into the valve at the back of the balloon. 2. Release the helium slowly so that the balloon starts to inflate and increase it gradually until the balloon is full and firm. Warning: Do not over- inflate the balloon. The balloon’s valve does not require sealing after inflation. Warning: DO NOT OVERINFLATE THE BALLOON. Only inflate with helium. Do not use any other type of gas. Do not use any other inflation devices such as a foot pump. For easy-to-follow video instructions go to www.wowstuff.com/airswimmers You can store your Air Swimmer by attaching the hook on the end of the remote control (7) to one of the loops on the bottom of the Air Swimmer. Pod The pod (11) requires 1 x AAA battery (13). Remote Control The remote control (7) requires 1 x AA batteries (12). 5. Fold over the fastening clips on the tail motor unit to secure. 6. Place the tail motor unit (8) on the back of the Air Swimmer balloon and attach the three elastic bands to the hooks on the motor unit. Make sure the plug connection on the tail motor unit faces downwards. plug connector Attaching the Pod clips clips 1. Attach the pod track (11), by hooking the hooks through the holes at the front of the underside of the Air Swimmer. 2. Make sure the hooks are hooked through as shown. The front of the pod (the fan should always be at the front), closest to the nose of the Air Swimmer. 1. Remove the liner of the double-sided sticky pads (9). Attach each fin in place on the Air Swimmer balloon (marked ‘place fin here’), as shown. 2. Place clear tape tabs (6) over the fin tabs to secure. Attaching the Fins 3. Loop the electric wire from the pod through the hoops underneath the Air Swimmer balloon. 4. Plug the electric wire into the tail motor unit as shown. Note: Ensure the electric wire has the correct orientation to the tail motor unit, as pins on tail motor unit can become bent and damaged. 1. Turn the power switch to “ON” on the pod (11), and the red LED will illuminate. Flying your Air Swimmer Attaching the Putty Holder 1. Attach the putty holder (14) to the holes on the under side of the back of the Air Swimmer. Add small bits of putty (10) until the Air Swimmer floats at roughly 5 feet (1.5m), neither rising or falling. If it starts to descend, remove some of the putty. NOTE: The putty holder may not need to be used, if the Air Swimmer floats at roughly 5 feet (1.5m) before the putty holder is attached. This is dependant on your altitude. 3. To move the Air Swimmer up, press up on the remote. To move the Air Swimmer down, press down on the remote. 1. If you fly more than one Air Swimmer in close proximity each Air Swimmer needs to be changed to a different channel. To do this push the switch on the handset to either A, B or C. Please note: You do not need to complete this instruction unless more than one Air Swimmer are being swam in close proximity. 5. To turn your Air Swimmer, press and hold the button in the direction you wish to turn. This will give you a tight turning circle, but the Air Swimmer will move slowly. To find out different ways of turning your Air Swimmer visit www.wowstuff.com/airswimmers. Please note: You cannot turn and swim your Air Swimmer forwards at the same time. Changing The Frequency Channel www.wowstuff.com • 2 x AA batteries for remote controller (Included) For more troubleshooting please go to www.wowstuff.com/airswimmers 1. Thread one of the elastic bands (5) through the hole situated on the top of the Air Swimmers back (as shown). 2. Thread the elastic band through itself to create a loop. 3. Loop a second and third elastic band through the hole situated underneath the Air Swimmer in the same way. (Both through the same hole, as shown). 4. Attach the tail fin (4) to the tail motor unit (8) by slotting the rods into the tail motor unit arms, as shown. Assembling the Tail Motor Unit KILLER WHALE AAx2 www.wowstuff.com/airswimmers 4. To get your Air Swimmer moving, you will need to move the tail up and down by pressing up, down, up, down in a constant rhythm. Experiment with faster and slower rhythms to find the best speed. 2 18 9 4 6 7 5 ON OFF CE REQUIREMENT Hereby, China Industries Ltd. t/a Wow! Stuff, declares that this AR-1001 & AR-1002 & AP-1008 are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. To which must be added: - the exact location from which a copy of the DoC may be obtained (internet or postal address) or - a copy of the DoC in the original language is enclosed with the equipment FCC NOTE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operated in conjunction with any other antenna or transmitter. Notice This device intent to market to EU member states and U.S,use in other countries may cause a risk.

EL357 27.045 ~ 27.225MHz Transmitter Operation Description Mar.10, 2007 Confidential Page 1 of 3 The Microprocessor (U3, Figure 1) reads input commands (SW1/SW2/W3/W4,Figure 1),and then encodes them to digital codes. The codes are sent to RF oscillator via pin 8 of U3, R17 and then modulates 27.045~27.225MHz carry frequency signal via Q1 (Figure 2) to achieve AM signal . Figure 1 EL357 27.045 ~ 27.225MHz Transmitter Operation Description Mar.10, 2007 Confidential Page 2 of 3 The Radio Frequency of the transmitter is based on standard 27MHz AM citizen’s band. It generates low power 27.045~27.225MHz AM carrier frequency via major components of Q1, Y1, L1, C5, C3, R3, R28, and R4 etc. (Figure 2). Please note that the value of the components may vary. Please see the attached schematics for more detail. Figure 2 EL357 27.045 ~ 27.225MHz Transmitter Operation Description Mar.10, 2007 Confidential Page 3 of 3 The AM signal is passed to RF amplifier (Figure 3, Q2, C9, R9 and L2), which amplifies the signal and then couples the signal into the antenna (ANT1) via components C4,C6,C16,C7,L4 and L3. Figure 3

China Industries Ltd. T/A Wow! Stuff. FCC ID: YCR-AR-SWR-3C POWER OF ATTORNEY June 12, 2012 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on June 11,2013 This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, China Industries Ltd. T/A Wow! Stuff. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely,

Waltek Services (Shenzhen) Co., Ltd 1/F, Fukangtai Building, West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China Report No.: WT12064292SSF This Test Report is issued by the Company subject to its General Conditions of Service Printed overleaf or available on request and accessible at http://www.waltek.com.cn. Attention is drawn to the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test report cannot be reproduced, except in full, without prior written permission of the Company Test Location: 1/F, Fukangtai Building,West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China. Web: www.waltek.com.cn Email: [email protected] Tel: 0086-755-83551033 Fax: 0086-755-83552400 Page 18 of 21 7 Photographs - Constructional Details 7.1 EUT(Model: AR-1001) – Front View 7.2 EUT(Model: AR-1001) – Back View

Waltek Services (Shenzhen) Co., Ltd 1/F, Fukangtai Building, West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China Report No.: WT12064292SSF This Test Report is issued by the Company subject to its General Conditions of Service Printed overleaf or available on request and accessible at http://www.waltek.com.cn. Attention is drawn to the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test report cannot be reproduced, except in full, without prior written permission of the Company Test Location: 1/F, Fukangtai Building,West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China. Web: www.waltek.com.cn Email: [email protected] Tel: 0086-755-83551033 Fax: 0086-755-83552400 Page 21 of 21 8 FCC ID Label This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The Label must not be a stick-on paper. The Label on these products must be permanently affixed to the product and readily visible at the time of purchase and must last the expected lifetime of the equipment not be readily detachable. Proposed Label Location on EUT EUT Top View/ proposed FCC Label Location === End of Test Report === FCC ID: YCR-AR-SWR-3C This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)this device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC ID Label Sample for Model: AR-1001 & AR-1002 & AR-1008 & AR-1003 FCC ID: YCR-AR-SWR-3C This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Waltek Services (Shenzhen) Co., Ltd 1/F, Fukangtai Building, West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China Report No.: WT12064292SSF This Test Report is issued by the Company subject to its General Conditions of Service Printed overleaf or available on request and accessible at http://www.waltek.com.cn. Attention is drawn to the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test report cannot be reproduced, except in full, without prior written permission of the Company Test Location: 1/F, Fukangtai Building,West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China. Web: www.waltek.com.cn Email: [email protected] Tel: 0086-755-83551033 Fax: 0086-755-83552400 Page 19 of 21 7.3 EUT (Model: AR-1001)– Open View 7.4 PCB(Model: AR-1001) – Front View Waltek Services (Shenzhen) Co., Ltd 1/F, Fukangtai Building, West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China Report No.: WT12064292SSF This Test Report is issued by the Company subject to its General Conditions of Service Printed overleaf or available on request and accessible at http://www.waltek.com.cn. Attention is drawn to the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test report cannot be reproduced, except in full, without prior written permission of the Company Test Location: 1/F, Fukangtai Building,West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China. Web: www.waltek.com.cn Email: [email protected] Tel: 0086-755-83551033 Fax: 0086-755-83552400 Page 20 of 21 7.5 PCB(Model: AR-1001) – Back View

EL357 27.045 ~ 27.225MHz Transmitter Operation Description Mar.10, 2007 Confidential Page 1 of 3 The Microprocessor (U3, Figure 1) reads input commands (SW1/SW2/W3/W4,Figure 1),and then encodes them to digital codes. The codes are sent to RF oscillator via pin 8 of U3, R17 and then modulates 27.045~27.225MHz carry frequency signal via Q1 (Figure 2) to achieve AM signal . Figure 1 EL357 27.045 ~ 27.225MHz Transmitter Operation Description Mar.10, 2007 Confidential Page 2 of 3 The Radio Frequency of the transmitter is based on standard 27MHz AM citizen’s band. It generates low power 27.045~27.225MHz AM carrier frequency via major components of Q1, Y1, L1, C5, C3, R3, R28, and R4 etc. (Figure 2). Please note that the value of the components may vary. Please see the attached schematics for more detail. Figure 2 EL357 27.045 ~ 27.225MHz Transmitter Operation Description Mar.10, 2007 Confidential Page 3 of 3 The AM signal is passed to RF amplifier (Figure 3, Q2, C9, R9 and L2), which amplifies the signal and then couples the signal into the antenna (ANT1) via components C4,C6,C16,C7,L4 and L3. Figure 3

11 22 33 44 D D C C B B A A Model NameModel No. Title ManagerExamineDraw DateDateDate Sheet of Electric Engineer Department M S L DATE APP.BY DESIGNED BY DESCRIPTION REV DWG NO. Page C9103 R34.7k C8100P C4 82P C756p R9100R/1206 C347P ANT1 R4 100 Y127.145MHz R710K L34.7uH C6100P C568P L22.2uH L12.2uH R1100 C1NC R17 2.2k Q1C380Y C12NC C16 22P Q68050D C21NC L4 0.56uH Q7S8550 R264.7k R2710k VCC R284.7k C22102 VDD C18104 BATT13V VCC C14104 BT+ C11220uF/16V 遥控鲸鱼控制器 (27MH) EL357 TX E007-06EL357-01ZP VCC C1047uF/16V SW1RIGHTSW2BACKSW3LEFTSW4 FORWARD C17104 1 2 3 4 SW5ID SET RightBackwardLeftForward VDD F10.9A ID_SET Data C2104 C19104 P22 1 P21 2 P20 3 VDD 4 P13/XIN 5 P12/XOUT 6 P11/RST 7 P54 8 P10 9 P00 10 VSS 11 P25 12 P24 13 P23 14 U3TX Backward Forward RightLeftData ID_SET VDD 1 2 LED1RED R2330 Q28050D DWG-A11-EL357-06-01 00# 曾祥有 20120612 L568uH D141N5819 R10NC PWN R8330 PWN Q38050D TX_ON/OFF 20120612 R5510K F=40KHz Duty:60% VDD1 R12330 Q58050D R64.7k R11100 ON/OFF ON/OFF Q4S8550 VCC C27104 C1547uF/16V TX_ON/OFF VCC Q88050D R29330 Z115V

Waltek Services (Shenzhen) Co., Ltd 1/F, Fukangtai Building, West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China TEST REPORT Report No.: WT12064292SSF This Test Report is issued by the Company subject to its General Conditions of Service Printed overleaf or available on request and accessible at http://www.waltek.com.cn. Attention is drawn to the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test report cannot be reproduced, except in full, without prior written permission of the Company Test Location: 1/F, Fukangtai Building,West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China. Web: www.waltek.com.cn Email: [email protected] Tel: 0086-755-83551033 Fax: 0086-755-83552400 Page 1 of 21 Applicant : China Industries Ltd. T/A Wow! Stuff. Address of Applicant : Creative Industries Centre, Wolverhampton Science Park, Wolverhampton, WV109TG,UK The following samples were submitted and identified by/on behalf of the client as: Sample Description : Air Swimmers Shark & Air Swimmers Clown Fish & Air Swimmers-Piranha & Air Swimmers- Killer Whale Style/model No : AR-1001 & AR-1002 & AR-1008 & AR-1003 Operation Frequency : 27.145MHz FCC ID : YCR-AR-SWR-3C Sample Receiving Date : July 03, 2012 Test Period : July 03, 2012 to July 26, 2012 Test Requested : In accordance with the FCC Part 15 Subpart C,Section 15.227:2010 Test Method : ANSI C63.4: 2003 Test Conclusion : Based on the performed tests on the submitted samples, the results comply with the FCC Part 15 C Section 15.227 requirements. ******** For Further Details, Please Refer to the Following Page(s) ******** Signed for and on behalf of Waltek Services (Shenzhen) Co., Ltd. Philo.Zhong EMC Laboratory Manager Waltek Services (Shenzhen) Co., Ltd 1/F, Fukangtai Building, West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China Report No.: WT12064292SSF This Test Report is issued by the Company subject to its General Conditions of Service Printed overleaf or available on request and accessible at http://www.waltek.com.cn. Attention is drawn to the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test report cannot be reproduced, except in full, without prior written permission of the Company Test Location: 1/F, Fukangtai Building,West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China. Web: www.waltek.com.cn Email: [email protected] Tel: 0086-755-83551033 Fax: 0086-755-83552400 Page 2 of 21 1 Contents 1 CONTENTS .............................................................................................................................................................. 2 2 TEST SUMMARY ................................................................................................................................................... 3 3 GENERAL INFORMATION ................................................................................................................................. 4 3.1 CLIENT INFORMATION ...................................................................................................................................... 4 3.2 GENERAL DESCRIPTION OF E.U.T. ................................................................................................................... 4 3.3 E.U.T. ENVIRONMENT AND TEST MODES .......................................................................................................... 4 3.4 TEST LOCATION ............................................................................................................................................... 5 3.5 OTHER INFORMATION REQUESTED BY THE CUSTOMER .................................................................................... 5 3.6 TEST FACILITY ................................................................................................................................................. 5 4 EQUIPMENT USED DURING TEST ................................................................................................................... 6 4.1 EQUIPMENTS LIST ............................................................................................................................................ 6 4.2 MEASUREMENT UNCERTAINTY ........................................................................................................................ 6 4.3 EQUIPMENTS CALIBRATION .............................................................................................................................. 7 5 TEST RESULT & MEASUREMENT DATA ....................................................................................................... 8 5.1 RADIATED EMISSION ........................................................................................................................................ 8 5.2 EUT SETUP ...................................................................................................................................................... 9 5.3 SPECTRUM ANALYZER SETUP ........................................................................................................................ 10 5.4 TEST RESULT .................................................................................................................................................. 10 5.5 OCCUPIED BANDWIDTH .................................................................................................................................. 16 6 PHOTOGRAPHS - TEST SETUP ....................................................................................................................... 17 6.1 SPURIOUS EMISSION ......................…

Text truncated - open the document above for the full version.

Waltek Services (Shenzhen) Co., Ltd 1/F, Fukangtai Building, West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China Report No.: WT12064292SSF This Test Report is issued by the Company subject to its General Conditions of Service Printed overleaf or available on request and accessible at http://www.waltek.com.cn. Attention is drawn to the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test report cannot be reproduced, except in full, without prior written permission of the Company Test Location: 1/F, Fukangtai Building,West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China. Web: www.waltek.com.cn Email: [email protected] Tel: 0086-755-83551033 Fax: 0086-755-83552400 Page 17 of 21 6 Photographs - Test Setup 6.1 Spurious Emission Below 30MHz From 30MHz to 1000MHz