Z8ABOLTBluetooth Mono Headset

Bluetooth chipset: IS1632N-182 Bolt Bluetooth Mono headset specifications ■ Basic Specification Battery Specifications: DC3.7V by battery Operating temperature: -10 ~ 60 °C (0 ~ 40 at°C charging) Storage temperature: -40 ~ 60 °C FCC ID:Z8ABOLT ■ MIC & Speaker Speaker: Φ13mm * 4.5mm Magnetic Type: Neodymium Distortion: less than 1% Maximum output: 5mw Minimum output: 3mw Impedance: 32Ω typ Type MIC: Condenser MIC sensitivity:-45dB ± 3dB ■ Bluetooth Bluetooth Version: Ver.2.1 + EDR Profile: HSP1.1/HFP1.5 ※ CCAP Devices: Bolt Pin Code: 0000 RF: 3.58dBm(max) for GFSK modulation Receiver sensitivity:-70dBm Transmission Range (Hz) 20 - 20,000 Antenna Gain: 0.8dBi ■ Reliable of Mechanic Button: 100,000 Charge Plug: 5000 times ■ Operation Power ON: Press and hold the MFB for 3 seconds, And blue LED flashes three times fast, Simultaneous you can hearing the voice like "Du" form headset Power OFF: Headset Power ON state. Press and hold the MFB for 3 seconds, at 1st second you can hear the voice like "Ding" form headset. Then blue LED flashes twice fast. You can hear the voice like "Du" form headset again. Pairing: In headset Power Off state. Press and hold the MFB for 5 seconds. At 3 seconds, the blue LED will flash three times, and you can hear the voice like "Du" form headset. LED continues to blink alternating red and blue. Also you can hear the voice like “Du” Du form headset. *If you have release the MFB before LED continues to blink alternating red and blue. The headset will be into Power On state. At this time please make headset power off and on, do the above again. *When after pairing and connection mobile phone. If you off the headset or mobile phone and on once again. You can hear the voice like "Du" form headset. And it will automatically reconnect to the phone and just connected Take an incoming call: You can hear a ring tone from the headset and mobile phone simultaneously. Press the MFB you can take the incoming call. Outbound call: Please operate directly from a mobile. If the headset is connected to the mobile phone, voice was from the headset. * You can also switch the mobile phone's voice on with same button at mobile. If support it. End the call: Press the MFB button. Redial: Press and hold the MFB of headset for 1 second, the mobile will sent automatically to the last call. At the same time you can hear the voice like "Ding" form headset. Voice Switching: Please operate you mobile. Specific operations are subject to mobile phone Reconnect: If the headset and mobile phone disconnected. For example, the headset and mobile phone away than the distance of the radio signal than 10 seconds. Or Power off and on again. Or doing some operation must be turned off the Bluetooth function. Press MFB (same mobile phone may be asking you “Do you want to connect?”). Headset and mobile phone will be reconnected. Voice dialing (If your phone has this feature): the mobile phone and the headset is connected state. Press MFB once. You can start Voice dialing call. Voice commands, depending on the configuration of the mobile phone. ■ Indicator Charging-------------------------------------------------- Red LED lights Full charge------------------------------------------------ Blue LED lights Power on (Standby/Talking/Incoming call) ------- Blue LED flashes twice every 3 seconds Power on (Not Connection) ------------------------- Blue LED flashes once every 3 seconds Power shortage-----------------------------------------The red LED blinks three times each 3 seconds. And you can hear the voice like “Di”,”Di” form headset. Pairing----------------------------------------------------- LED flashes alternating red and blue. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Nov Fed Aut FCC Re: Pur s requ 1: B 2: C 3: O 4: P Th e rele app Th e all a app Sin c SIN Co Titl Te l vember 8, deral Comm thorization C ID: Z8AB : Confiden suant to Se uests confid Block Diagra Circuit Diagra Operational D Parts List e above mat ased to the licant and p e Applicant u accompanyi lication. cerely, NO STAR ntact per e: Presid : 852-271 2011 munication and Evalu BOLT ntiality Re ctions 0.457 ential treatm m am Description terials conta e public. The rovide unjus understands ng docume n R CREAT rson: Ave dent 108200 n Commiss uation Divis quest 7 and 0.459 ment of infor ain trade se e public dis stified benef that pursua ntation will ION LIMI e Huang sion sion 9 of the Com rmation appl ecrets and p sclosure of t fits to its com nt to Rules 0 not be mad ITED. mmission’s R ied this app proprietary these matte mpetitors. 0.457, disclo e before th Rules, the a lication as o information ers might be osure of this e date of th applicant he outlined belo not custom e harmful to s Application he Grant for ereby ow: marily o the n and r this

FCC ID Label Location FCC ID: Z8ABOLT

OPEN VIEW OF EUT-1 OPEN VIEW OF EUT-2 INTERNAL VIEW OF EUT-1 INTERNAL VIEW OF EUT-2 Bluetooth Antenna

FCC Test Report Report No.: AGC143111002F2 FCC ID : Z8ABOLT PRODUCT DESIGNATION : Bluetooth Mono Headset BRAND NAME : Quikcell TEST MODEL : Bolt CLIENT : SINO STAR CREATION LIMITED. DATE OF ISSUE : Nov.05, 2011 STANDARD(S) : FCC Part 15 Rules Attestation of Global Compliance Co., Ltd. CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context. Report No.: AGC143111002F2 Page 1 of 38 VERIFICATION OF COMPLIANCE Applicant SINO STAR CREATION LIMITED. NO.1318-19 ,HOLLYWOOD PLAZA, 610 NATHAN ROAD, MONGKOK, KOWLOON, HK Manufacturer Shenzhen LUXPRO Electronic Technology Co., Ltd 3F,B4 Building, Gonghe 1 st Industrial Zone , Shajing Town, Bao'an District, Shenzhen Product Designation Bluetooth Mono Headset Brand Name Quikcell Model Name Bolt,BT3109,BT2108,BT2109,BT3108 Model Difference The same PCBA with different exterior. FCC ID Z8ABOLT Date of Test AGC143111002F2 Date of test Nov.01 to Nov.05, 2011 WE HEREBY CERTIFY THAT: The above equipment was tested by Attestation of Global Compliance Co., Ltd. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (2003) and the energy emitted by the sample EUT tested as described in this report is in compliance with radiated emission limits of FCC Rules Part 15.247. Tested By: Angela Li Nov.05, 2011 Reviewed By: Forrest Lei Nov.05, 2011 Approved By: Solger Zhang Nov.05, 2011, Report No.: AGC143111002F2 Page 2 of 38 TABLE OF CONTENTS 1 GENERAL INFORMATION ..................................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION .......................................................................................................................................... 4 1.2 TABLE OF CARRIER FREQUENCYS ...................................................................................................................... 4 1.3 RECEIVER INPUT BANDWIDTH ............................................................................................................................... 5 1.4 EXAMPLE OF A HOPPING SEQUENCY IN DATA MODE ................................................................................... 6 1.5 EQUALLY AVERAGE USE OF FREQUENCIES AND BEHAVIOUR ................................................................. 6 1.6 RELATED SUBMITTAL(S) / GRANT (S)................................................................................................................... 6 1.7 TEST METHODOLOGY ............................................................................................................................................... 6 1.8 TEST FACILITY .............................................................................................................................................................. 7 1.9 SPECIAL ACCESSORIES ........................................................................................................................................... 7 1.10 EQUIPMENT MODIFICATIONS ................................................................................................................................. 7 2 SYSTEM TEST CONFIGURATION ....................................................................................................................................... 8 2.1 CONFIGURATION OF TESTED SYSTEM............................................................................................................... 8 2.2 EQUIPMENT USED IN TESTED SYSTEM ............................................................................................................. 8 3 SUMMARY OF TEST RESULTS ............................................................................................................................................ 9 4. DESCRIPTION OF TEST MODES ....................................................................................................................................... 9 5 PEAK OUTPUT POWER ....................................................................................................................................................... 10 5.1 MEASUREMENT PROCEDURE ............................................................................................................................... 10 5.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ............................................................................... 10 5.3 MEASUREMENT EQUIPMENT USED .................................................................................................................... 11 5.4 LIMITS AND MEASUREMENT RESULT ................................................................................................................. 11 6 20 DB BANDWIDTH ............................................................................................................................................................. 12 6.1 MEASUREMENT PROCEDURE ............................................................................................................................... 12 6.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ............................................................................... 12 6.3 MEASUREMENT EQUIPMENT USED .................................................................................................................... 12 6.4 LIMITS AND MEASUREMENT RESULTS ............................................................................................................... 12 7. CONDUCTED SPURIOUS EMISSION .............................................................................................................................. 14 7.1 MEASUREMENT PROCEDURE ............................................................................................................................... 14 7.2 TEST SET-UP (BLOCK DIAG…

Text truncated - open the document above for the full version.

RADIATED SPURIOUS EMISSION