ZGY-TX5Wireless Transmitter Module

ASK Transmitter Module Gener al Description: 4 33 .9 MHz ASK TRANSMITTER The TX5 is an ASK Hybrid transmitter module. The TX5 is an ASK transmitter module .The result is excellent performance in a simple-to-use .The TX5 is designed specifically for remote-control , wireless mouse and car alarm system operating at 4 33MHZ Frequency Range: .9MHZ. Supply Voltage: 1.8~3.6V. Circuit Shape: ASK Transmitter IC Notes: According FCC regulations, the resistor value is 150ohm recommended. Applications ¦ Car security system ¦ Remote keyless entry ¦ Garage door controller ¦ Home security ¦ Wireless mouse ¦ Automation system Product Identification Absolute Maximum Ratings Parameter Rating Rating Supply Voltage 1.8—3.6 V DC Operating Temperature -40 to +85 °C Page 1 of 3 6/12/2009 433 TX5-4 33M 4 33MHZ Pin Dimension 11 . 7 m m IC side crystal 16.30m m ②①③ Pin-layout(from left to right)： ① ANT ② VDD ③ DATA ④ GND ④ Typical Application: Remarks: Page 2 of 3 6/12/2009 Antenna length is about 17.8cm @433MHz for whip antenna; or the length and shape of other type atenna is reference to certain product stting, e.g. spiry attenan. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to o perate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfe rence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to corr ect the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experien ced radio/TV tech nician for help. Page 3 of 3 6/12/2009 FCC ID: ZG Y -TX5

HK OFFICE Flat10,5/F,Block A,Hoplite Industrial Centre ,3-5 Wang Tai Road , Kowloon Bay ,Kowloon,HK TEL&FAX: 852-35862918 Http://www.favoru.com Email:[email protected] SALES OFFICE 中国广东珠海市金鼎创新4路36号 36,4 th Innovation Road, Zhuhai, Guangdong, China TEL: 86)756-3630283 FAX:86)756-3630288 April 8, 2011 To: SIEMIC, INC. 2206 Ringwood Avenue, San Jose, CA 95131 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, Favoru Electronic Co., Ltd hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): EUT: Wireless Transmitter Module M/N:TX5 (FCC ID : ZGY-TX5) We affirm that between SIEMIC and Favoru Electronic Co., Ltd , any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Client’s signature Angel Chung(Sales Manager)

HK OFFICE Flat10,5/F,Block A,Hoplite Industrial Centre ,3-5 Wang Tai Road , Kowloon Bay ,Kowloon,HK TEL&FAX: 852-35862918 Http://www.favoru.com Email:[email protected] SALES OFFICE 中国广东珠海市金鼎创新4路36号 36,4 th Innovation Road, Zhuhai, Guangdong, China TEL:86)756-3630283 FAX:86)756-3630288 FCC ID : ZGY-TX5 Model : TX5 Type of Equipment: Wireless Transmitter Module Applicant: Favoru Electronic Co., Ltd Request for Limited Modular Transmitter Approval The modular transmitter is designed by Favoru Electronic Co., Ltd. This modular transmitter is not provided for OEM. This modular transmitter will only be installed in a remote-control which is produced by a specific manufacturer. The modular transmitter complies with the module basic requirements (item 1 to 8) in FCC Part 15 Section 15.212 for modular transmitters. Module basic requirements 1. Have its own RF shielding: The modular transmitter does not have its own RF shielding. The Grantee will retain control over the final installation of the device. The module is only approved for use when installed in devices produced by a specific manufacturer. Full compliance of the end product is always ensured. 2. The modular transmitter must have buffered modulation/data inputs: Data input to the modular transmitter is controlled as not generating excessive data rates or over-modulation. 3. The modular transmitter must have its own power supply regulation: The modular transmitter has its own power supply regulation to provide stable 3 V. Pls. refer to the schematic. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c): The antenna is permanently attached by a trace of PCB layout. 5. The modular transmitter must be tested in a stand-alone configuration: The modular transmitter was tested in a stand-alone configuration. Pls. refer to the test setup photo. AC or DC power lines and data input/output lines connected to the module do not contain ferrites. The length of these lines was length typical of actual use. Any accessories, peripherals, or support equipment connected to the module during testing are unmodified. 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module.: The modular transmitter has its own FCC ID: ZGY-TX5. The outside of the device into which the module is installed will also be display a label referring to the enclosed module. This exterior HK OFFICE Flat10,5/F,Block A,Hoplite Industrial Centre ,3-5 Wang Tai Road , Kowloon Bay ,Kowloon,HK TEL&FAX: 852-35862918 Http://www.favoru.com Email:[email protected] SALES OFFICE 中国广东珠海市金鼎创新4路36号 36,4 th Innovation Road, Zhuhai, Guangdong, China TEL:86)756-3630283 FAX:86)756-3630288 label uses wording as the following: “Contains Transmitter Module FCC ID: ZGY-TX5”. The Grantee provides adequate instructions along with the module which explain this requirement. A copy of these instructions is included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements: The modular transmitter complies with Section 15.231(a). This RF Module is powered from a host unit. It communicates with the host unit to receive data like data-transmitting. The transmission Release Time is 1.2s. The transmission time and the silent period are limited by the MCU of the RF module, independent of any host unit. 8. The modular transmitter must comply with any applicable RF exposure requirements: The module complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets with the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. The module has very low levels of RF energy that it is deemed to comply without testing of specific absorption ration (SAR). We apply for a “Limited Modular Approval” (LMA). The Grantee will retain control over the final installation of the device. The module is only approved for use when installed in devices produced by a specific manufacturer. Full compliance of the end product is always ensured. Manager Favoru Electronic Co., Ltd TX5 Modular Approval Letter Page 4 of 4 Rev 4.0 LMA Declaration Letter We , (Favoru Electronic Co., Ltd) declared that will retain control over the final installation of the device, (FCC/IC ID: ZGY-TX5 ) such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must be only approved for use when installed in devices produced by a specific manufacturer. Client’s signature Client’s name / title Contact information / address

Antenna

FCC Certification label Sample FCC ID: ZGY-TX5

Label location

Antenna

Applicant: Favoru Electronic Co., Ltd FCC ID: ZGY-TX5 Transmitter Circuit Description The transmitter consists of 3V Battery, RF Generator and RF Modulate IC, Crystal, Matched network and Antenna. A. 13.560MHz Crystal X1 is the accessory for RF Generator and RF Modulate IC U2 . Through the 32 times-amplifier of the frequency in the inner of the IC, it create the carrier frequency (f0:433.92MHz) of the RF signal. B. In the RF Circuit application, the antenna consists of whip wire line (diameter: 0.5mm，Length:150mm), the necessary the matched circuit consists of Inductance L4 and Capacitance C5, C11 and C7. There is no external ground connection. The ground is only that of the printed circuit board. C. This device power-supplied by 3V battery and in terms of periodic transmitting to decease the power consumption, gets the data from outside source, generates the RF signal through RF Generator and RF Modulate IC, then radiate the RF signal to the sky via antenna through matched network, and complete the data-transmitting process wirelessly.

11 22 33 44 D D C C B B A A TitleSizeDate Revision SheetDrawn By: of ANT C1322p C1100P C5 1P C10106 C1422p R70ohm L4 180N L1470nH Y113.560MHz C11* C73.9P VDD VDDDATA 1 123 J1CON3 DATA VDD 123 456 U2IRA385 R70ohm

Page 1 of 32 FCC ID: ZGY-TX5 ACCURATE TECHNOLOGY CO., LTD REPORT NO. ATE20110596 APPLICATION CERTIFICATION On Behalf of Favoru Electronic Co., Ltd Wireless Transmitter Module Model No.: TX5 FCC ID: ZGY-TX5 Prepared for : Favoru Electronic Co., Ltd Address : 36, 4 th Innovation Road, Zhuhai, Guangdong, China 519085 Prepared by : ACCURATE TECHNOLOGY CO., LTD Address : F1, Bldg. A, Changyuan New Material Port, Keyuan Rd. Science & Industry Park, Nanshan, Shenzhen, Guangdong P.R. China Tel: (0755) 26503290 Fax: (0755) 26503396 Report Number : ATE20110596 Date of Test : April 11-16, 2011 Date of Report : April 20, 2011 Page 2 of 32 FCC ID: ZGY-TX5 ACCURATE TECHNOLOGY CO., LTD REPORT NO. ATE20110596 TABLE OF CONTENTS Description Page Test Report Certification 1.GENERAL INFORMATION ..........................................................................................................4 1.1.Description of Device (EUT)....................................................................................................................4 1.2.Description of Test Facility ......................................................................................................................5 1.3.Measurement Uncertainty.........................................................................................................................5 2.MEASURING DEVICE AND TEST EQUIPMENT ..................................................................... 6 3.SUMMARY OF TEST RESULTS................................................................................................... 7 4.THE FIELD STRENGTH OF RADIATION EMISSION ............................................................ 8 4.1.Block Diagram of Test Setup....................................................................................................................8 4.2.The Field Strength of Radiation Emission Measurement Limits..............................................................9 4.3.Configuration of EUT on Measurement ...................................................................................................9 4.4.Operating Condition of EUT ....................................................................................................................9 4.5.Test Procedure ........................................................................................................................................10 4.6.The Field Strength of Radiation Emission Measurement Results ..........................................................11 5.20DB OCCUPIED BANDWIDTH ................................................................................................ 13 5.1.Block Diagram of Test Setup..................................................................................................................13 5.2.The Bandwidth of Emission Limit According To FCC Part 15 Section 15.231(c) ................................13 5.3.EUT Configuration on Measurement .....................................................................................................14 5.4.Operating Condition of EUT ..................................................................................................................14 5.5.Test Procedure ........................................................................................................................................14 5.6.Measurement Result ...............................................................................................................................15 6.RELEASE TIME MEASUREMENT............................................................................................ 16 6.1.Block Diagram of Test Setup..................................................................................................................16 6.2.Release Time Measurement According To FCC Part 15 Section 15.231(a) ..........................................16 6.3.EUT Configuration on Measurement .....................................................................................................17 6.4.Operating Condition of EUT ..................................................................................................................17 6.5.Test Procedure ........................................................................................................................................17 6.6.Measurement Result ...............................................................................................................................18 7.AVERAGE FACTOR MEASUREMENT .................................................................................... 19 7.1.Block Diagram of Test Setup..................................................................................................................19 7.2.Average factor Measurement according to ANSI 63.4: 2003.................................................................19 7.3.EUT Configuration on Measurement .....................................................................................................20 7.4.Operating Condition of EUT ..................................................................................................................20 7.5.Test Procedure ........................................................................................................................................20 7.6.Measurement Result ...............................................................................................................................21 APPENDIX I ( TEST CURVES) (10 pages) Page 3 of 32 Test Report Certification Applicant : Favoru Electronic Co., Ltd Manufacturer: Favoru Electronic Co., Ltd EUT Description : Wireless Transmitter Module (A) MODEL NO.: TX5 (B) SERIAL NO.: N/A (C) POWER SUPPLY: DC 3V Measurement Procedure Used: FCC Rules and Regulations Part 15 Subpart C Section 15.231 ANSI 63.4: 2003 The device described above is tested by ACCURATE TECHNOLOGY CO., LTD to determine the maximum emission levels emanating from t…

Text truncated - open the document above for the full version.

Radiated emissions test < 1GHz Radiated emissions test > 1GHz