ZIATAM001RTS Transmitter

Reactive Target System Ltd. All right reserved © Portable Wireless Shooting-Range System Operating and User’s Manual Reactive Target System Ltd. All right reserved © Introduction RTS (Reactive Target System) introduces a significant technological leap in erecting and managing wireless electronic shooting ranges. It provides accurate counting of hits in indoor and outdoor shooting ranges, both for combat trainees and private individuals. RTS revolutionary approach enable trainers and trainers to save time, increase productivity, and provide a better & safer shooting experience: • No need to walk to targets to check hits • Reduces idle time • No need to cross the line of fire • Execute more drills/shooting in less time • Spend more time on improving shooting skills and decision making Portable Wireless Shooting-Range System Components Qty Description Illustration 1 RTS Target Pole 1 RTS Target Base 1 RTS Numerator (controls up to 9 targets) 2 RTS Remote-Control 9 RTS Transmitter + RTS Hit Sensors 6 AA batteries for the Numerator Not included 9 CR-123 lithium photo batteries for Transmitter Included Reactive Target System Ltd. All right reserved © System Setup RTS Numerator Setup 1. Turn the RTS Numerator to its back side, open the batteries lid, and insert the six AA batteries. Close the batteries lid 2. Place a RTS Target Base, attach the RTS Target Pole, and mount the RTS Numerator. 3. Lift the left switch on monitor until the indicator “S 32” blinks for one second. 4. Hold down the right switch on the monitor, “Ln” (Learn) will lights up 5. Keep holding down the right switch until the message “Er” light up, which indicates that all previous records were erased. Preparing the targets 1. Place RTS Target Base on the ground, making sure it is stable, with captions facing the firing line. 2. Place the RTS Target Pole into the appropriate socket on the base and attach the place the RTS Self-Healing Torso to the upper part of the column. For a knock-over target, attach the RTS Smart Joint to the RTS Target Base using the round socket in the middle of the base. Insert the RTS Target Pole into the RTS Smart Joint. 3. Attach the RTS Hit Sensor to the RTS Target Pole, about 2 inches above the base, facing the firing line. 4. Connect the RTS Hit Sensor’s wire to the transmitter and make sure that it is properly connected. 5. Adjust the RTS Transmitter Hit Sensitivity Switch The transmitter’s switch has 3 positions: • Middle: normal sensitivity. • Left (away from the sensor connector): high sensitivity. • Right (toward the sensor connector) : low sensitivity. Insert transmitter into its socket in the base – sensitivity switch facing down and the antenna facing up. 6. Repeat for additional targets (up to 9 targets). Reactive Target System Ltd. All right reserved © Connecting RTS Remote-Control with the RTS Numerator 1. Hold down the RTS Numerator’s right button until LN lights up. 2. Press several times on any of the remote control buttons until R 1 is visible 3. Repeat procedure for up to 3 remote controls Connecting targets with the RTS Numerator 1. Hold down the RTS Numerator’s right button until LN lights up. 2. Hit the RTS Self Healing Target Torso with a metallic object o r shoot one bullet at it. T1 (Target No.1) appears on the monitor. 3. Repeat procedure for up to 9 targets. Reactive Target System Ltd. All right reserved © System Operation Operating the Remote Control 1. Button #1 (upper left corner) turns Monitor On/Off 2. Button #2 (upper right corner) rolls the target numbers forwards 3. Button #3 (bottom left corner) resets the score for the target on the display. 4. Button #4 (bottom right corner) rolls back to the targets on the monitor. 5. Pressing buttons 1 and 3 simultaneously will reset the score for all the targets. Low Battery Indicator RTS Transmitter Battery: at the point where the RTS Transmitter battery is about to be too weak for normal operation, the RTS Transmitter will report “Low Battery” to the RTS Numerator. When the RTS Numerator displays the score for that given RTS Transmitter (say “T3”) you will see the following sequence: 1. The RTS Numerator will display “T3” 2. After one second “Lb” will be displayed , and two fast beeps will be played 3. After addit ional second, the hit score for the target will be displayed. When you see the “Lb” indicator it is time to replace the battery in the target transmitter. RTS Numerator Batteries: at the point where the RTS Numerator batteries is about to be too weak for normal operation, the RTS Numerator will display the “Low Battery” indicator, “Lb” and play a beep for 2 seconds just before the screen goes to sleep mode (black out). You should immediately replace the batteries in the RTS Numerator. Operation Specifications: • Effective distance from target to monitor up to 300 meters depending on the topology and wireless interference conditions of the range’s area. Transmission range can be increased by raising the RTS Transmitter higher up from the ground level. • Closest effective firing range: 5 meters for pistol, 10 meters for rifle Reactive Target System Ltd. All right reserved © System Trouble Shooting Part Problem Reso lut ion Numerator Does not turn on: • Check that the batteries are correctly inserted. • Check that the batteries are fully charged and change if necessary. Numerator Incorrect scoring: 1. Check that the Transmitter operates correctly (see below) 2. Position the transmitter near the Numerator (10 yards) 3. Check for correct scoring. 4. If problem persist, replace the RTS Numerator batteries Sensor & Transmitter Unable to connect a target to the Numerator Or On target hits not counted by Numerator • Check that the RTS Hit Sensor connected firmly to the RTS Transmitter. • Position the Transmitter with the “RTS Ltd. Transmitter” is facing you. Note the led in the left bottom corner. • Set the Transmitter sensitivity switch to the left (away from connector) • Hit the target with a heavy object and watch the le…

Text truncated - open the document above for the full version.

FCC, Request for non-disclosure Date: 16-Jul-10 RF_501, Issue 6 Page 1 of 1 Company Name: Reactive Target System Ltd. Address : 43 Yakov Olamy Street City: Moshav Mishmar Hashiva Country: 50297 Israel To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: ZIATAM001 Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, a pplicant hereby requests Short-Term Confidential treatment of the following materials (note 1): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: Planned Release Date STC: (notes 2, 3, 4, 5) Date: April 28, 2011 Name and signature of applicant: Avishay Zur Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

RF_160, Issue 02 Declaration of Authorization We Name: Reactive Target System Ltd. Address: 43 Yakov Olamy Street City: Moshav Mishmar Hashiva, 50297 Country: Israel Declare that: Name Representative of agent: ............. (1) Agent Company name: Hermon Laboratories Ltd. Address: Harakevet Industrial Zone City: Binyamina 30500 Country Israel is authorized to apply for Certification of the following product(s): Product description: ... RTS Transmitter....... Type designation: ... TAM................... Trademark: ... NA........................................... on our behalf. Date: April 20, 2011 Name: Avishay Zur Function: President Signature: Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent.

May 1, 2011 Telefication B.V. Attn: Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Application for certification of an RTS Transmitter, FCC ID:ZIATAM001 Dear Gentlemen, Please find attached our application for certification of an RTS Transmitter, model number TAM, FCC ID:ZIATAM001, prepared in accordance with FCC Rules, part 15, subpart C, section 15.231(a). The product testing and this application for certification were performed by Hermon Laboratories, which is listed by FCC, Registration Numbers 90623, 90624. The FCC Designation Number is US1003. Hermon Labs responsible person is Mr. Michael Nikishin, tel: +972 4626 8440, fax:+972 4628 8277, e-mail: [email protected]. Please send an invoice to Hermon Labs. We hope this application satisfies your requirements Sincerely yours, Avishay Zur President

Hermon Laboratories Ltd. Harakevet Industrial Zone, Binyamina 30500, Israel Tel. +972-4-6288001 Fax. +972-4-6288277 E-mail: [email protected] Page 1 of 37 Report ID: RTSRAD_FCC.21920.doc Date of Issue: 4/20/2011 ELECTRICAL TESTING 0839.01 TEST REPORT ACCORDING TO: FCC CFR 47 PART 15 subpart C, section 15.231(a) FOR: Reactive Target System Ltd. RTS Transmitter Model number: TAM This report is in conformity with ISO/ IEC 17025. The "A2LA Accredited" symbol endorsement applies only to the tests and calibrations that are listed in the scope of Hermon Laboratories accreditation. The test results relate only to the items tested. This test report shall not be reproduced in any form except in full with the written approval of Hermon Laboratories Ltd. Report ID: RTSRAD_FCC.21920.doc Date of Issue: 4/20/2011 Page 2 of 37 Table of contents 1 Applicant information..................................................................................................................................................... 3 2 Equipment under test attributes .................................................................................................................................... 3 3 Manufacturer information .............................................................................................................................................. 3 4 Test details.................................................................................................................................................................... 3 5 Tests summary.............................................................................................................................................................. 4 6 EUT description............................................................................................................................................................. 5 6.1 General information....................................................................................................................................................... 5 6.2 Operating frequencies ................................................................................................................................................... 5 6.3 Test configuration.......................................................................................................................................................... 5 6.4 Transmitter characteristics ............................................................................................................................................ 5 7 Transmitter tests according to FCC 47CFR part 15 subpart C requirements ................................................................ 6 7.1 Periodic operation requirements ................................................................................................................................... 6 7.2 Field strength of emissions............................................................................................................................................ 8 7.3 Occupied bandwidth test ............................................................................................................................................. 19 7.4 Antenna requirements................................................................................................................................................. 21 8 APPENDIX A Test equipment and ancillaries used for tests....................................................................................... 22 9 APPENDIX B Test laboratory description.................................................................................................................... 23 10 APPENDIX C Abbreviations and acronyms ................................................................................................................ 24 11 APPENDIX D Test equipment correction factors ........................................................................................................ 25 12 APPENDIX E Measurement uncertainties................................................................................................................... 36 13 APPENDIX F Specification references ........................................................................................................................ 36 14 APPENDIX G Supplier Declaration ............................................................................................................................. 37 Report ID: RTSRAD_FCC.21920.doc Date of Issue: 4/20/2011 Page 3 of 37 1 Applicant information Client name: Reactive Target System Ltd. Address: 43 Yakov Olamy Street, Moshav Mishmar Hashiva 50297, Israel Telephone: +972.3.960.3399 Fax: +972.3.960.3312 E-mail: [email protected] Contact name: Mr. Michael Alon 2 Equipment under test attributes Product name: RTS Transmitter Model number: TAM Serial number: Prototype Hardware version: E Software release: 1.24 Receipt date: 4/10/2011 3 Manufacturer information Manufacturer name: Reactive Target System Ltd. Address: 43 Yakov Olamy Street, Moshav Mishmar Hashiva 50297, Israel Telephone: +972.3.960.3399 Fax: +972.3.960.3312 E-mail: [email protected] Contact name: Mr. Avishay Zur 4 Test details Project ID: 21920 Location: Hermon Laboratories Ltd. Harakevet Industrial Zone, Binyamina 30500, Israel Test started: 4/10/2011 Test completed: 4/17/2011 Test specification: FCC Part 15, subpart C, §15.231(a) Report ID: RTSRAD_FCC.21920.doc Date of Issue: 4/20/2011 Page 4 of 37 5 Tests summary Test Status Transmitter characteristics Section 15.231(a), Periodic operation requirements Pass Section 15.231(b), Field strength of emissions Pass Section 15.231(c), Occupied bandwidth Pass Section 15.207(a), Conducted emission Not required Section 15.203, Antenna requirement Pass Testing was completed against all relevant requirements of the test standard. The results obtained indicate that the product under test …

Text truncated - open the document above for the full version.

Reactive Target System Ltd. FCC ID:ZIATAM001 Page 1 of 7 SETUP PHOTOGRAPHS This document contains 6 photographs Reactive Target System Ltd. FCC ID:ZIATAM001 Page 2 of 7 Photograph No.1 Setup for spurious emission measurements in the anechoic chamber below 30 MHz Reactive Target System Ltd. FCC ID:ZIATAM001 Page 3 of 7 Photograph No.2 Setup for radiated emission measurements in the anechoic chamber from 30 to 1000 MHz Reactive Target System Ltd. FCC ID:ZIATAM001 Page 4 of 7 Photograph No.3 Setup for radiated emission measurements at OATS from 30 to 1000 MHz Reactive Target System Ltd. FCC ID:ZIATAM001 Page 5 of 7 Photograph No.4 Setup for radiated emission measurements in the anechoic chamber above 1 GHz Reactive Target System Ltd. FCC ID:ZIATAM001 Page 6 of 7 Photograph No.5 Setup for radiated emission measurements at OATS above 1 GHz Reactive Target System Ltd. FCC ID:ZIATAM001 Page 7 of 7 Photograph No.6 Setup for occupied bandwidth measurements