ZJZSAUNTERRLF

Energy efficent T4/T5 linksble slimline fittings SAFETY INSTRUCTIONS PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION MODELS NH-2A-14W(T5)、NH-2A-21W(T5)、NH-2A-28W(T5)、NH-2A-35W(T5)、NH-2A-28W(T4)、NH-2A-30W(T4)、 Pack cotents: 1 X Electtonic fluorescent fitting 1 x Mounring kit with butt connector This light fitting must be installed in accordance with the Building Regulations.These may be obtained frou HMSO or viewed and downloaded from www.saunter.com.cn following the link for Building Regukatins. Instrutions: 1. Switch off the mains before cmmencing installation and remove the appropriate circuit fuse. 2. Do not connect to a circuit which also has inductive loads.This may damage electronic components within your fitting. 3. This product is suitable for installation on surfaces with normal flammability (indicated by the F in a triangle)e.g.wood,plasterboard,masonry.It is NOT suitable for installation on highly flammable surfaces (e.g.polystyrene,textiles). 4. Before making fixing hole(s),check that there aie no obstructions hidden beneath the mornting surface such as pipesor cables. 5. If the location of your new fitting requires the provision of a new electrical supply,the supply must conform with the requirements of the Buiding Regulations. 6. This product is designed for permanent connection to fixed wiring:this should be either a suitable lighting circuit(protected with a 5or6Amp MCB or fuse)or a fused spur(with a 3 Ampfuse)via a fused connection unit.Werecommend that the supply incorporates a switch for ease of operation. 7. You are advised at every stage of your installation to double-check any electrical connections you have made.After you hace completed your installation there are electrical tests that should be carried out:these tests are specified in the Wiring Regulations(BS7671)referred to in the Building Regulations .If in doubt,consult a qualified electrician. How many fittings can be linked together? 10 fittings can be linked with 14 watt and 21 watt fittings 8 fittings can be linked 28 watt with 30 watt fittings 3 fittings can be linked with 35 watt fittings Warning:This device complies with Part 18 of FCC rules. Altering or adapting any of the leads,other than shortening the supply lead will invalidate your guarantee and could present a severe electrical shock hazard. Cleaning: · Clean this light fitting only with a soft dry cloth. · The diffuser may be removed and washed in a mild detergent solution.Make sure the diffuser is completely dry before putting back on your light fitting. · Do not use any chemical or abrasive cleaners. Lamp Teplacement: · Switch off electricity at the mains. · Life off the diffuser. · Rotate the lamp through approximately 90°and withdraw from the tube holders. · Insert new lamp and rotate to lock in position. · Restore power supply and tum on. Replacement lamp type: Wattage:14W,21W,28W,30W, 35W Supply Voltage:120V 50/60Hz Size:T4/T5 Eventually you may want to replace this light fitting: When your light fitting comes to the end of its life or you chose to update by replacing it,please do not dispose of this fitting,checkwith your retailer or local authority for suitable options.New regulations will encourage the recycling of waste from Electrical and Electronic Equipment (European ‘WEEE’ Directive effective August 2005). If you experience any problems: If your light is defective or develops a fault,please return it to where you bought it.If in doubt,consult a qualified electrician. This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communication equipment operating between 0.45–30 MHz. Variations of this language are permitted provided all the points of the statement are addressed and may be presented in any legible font or text style. www.saunter.com.cn

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS Model: NH-2A-30W (T4) EUT – Top View EUT – Bottom View Model: NH-2A-28W (T4) EUT – Top View EUT – Bottom View Model: NH-2A-28W (T5) EUT – Top View EUT – Bottom View Model: NH-2A-21W (T5) EUT – Top View EUT – Bottom View Model: NH-2A-14W (T5) EUT – Top View EUT – Bottom View Model: NH-2A-35W (T5) EUT – Top View EUT – Bottom View

EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Specifications : Text is Black or white in color and is left justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT.

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS Model: NH-2A-30W (T4) EUT – Cover off View EUT – Mainboard Top View EUT – Main Board Bottom View Model: NH-2A-28W (T4) EUT – Cover off View EUT – Mainboard Top View EUT – Main Board Bottom View Model: NH-2A-28W (T5) EUT – Cover off View EUT – Mainboard Top View EUT – Main Board Bottom View Model: NH-2A-21W (T5) EUT – Cover off View EUT – Mainboard Top View EUT – Main Board Bottom View Model: NH-2A-14W (T5) EUT – Cover off View EUT – Mainboard Top View EUT – Main Board Bottom View Model: NH-2A-35W (T5) EUT – Cover off View EUT – Mainboard Top View EUT – Main Board Bottom View

1 2 34 A BC D 4 3 2 1 D CB A Sheet Name Des ign Dr awing Review Ve r sion Re vision Compa ny Na me ZHOUG SHAN SAUNTER ELECTRIC CO.,LED Dat e Design department E ngine er ing De par t me nt 1.0 1st 2011/03/20 Jiesen Zhou Jiesen Zhou Jiesen Zhou Product Name L3 120V 2A/250V FUSE 120V VR1 7D271K 1N4007 D2 Q1 MJE13003 (T O-220) C6 CBB22 152J/630V R3 RY 680KΩ 1Ws R1 RY 100KΩ 1W R5 RY 1.5Ω 1/4W Q2 MJE13003 (TO-220) R7 RY 1.5Ω1/4W RY 680KΩ 1W s R2 SCR1 MCR100-6 RY 22Ω1/2 Ws R4 D8 1N4007 D9 1N4007 R6 RY 22Ω1/2 Ws C7 CL11 0.022uF/100V D3 1N4007 TD1 DB3 T5 14W OSC 10x6X5 L6 Φ 0.15mm 25Ts L7 Φ0.19mm 200Ts L6 、 L7=2.9-3.0mH CBB22 472J/1250V D11 FR107 PTC1 WMZ11B105S471N7D151K Q3 S9014 R12 RT 560Ω1/4 W R11 RT 56 Ω 1/4W R8 RT 1 5K Ω 1/ 4 W D12 FR107 C10 47uF/50V R9 RT 270KΩ1/4W LN C1 Y1 472M/250V GND L2 EE13Common mode L1= L2> 20 mH Φ 0.31mm 60TsX2 TD2 DB3 R10 RT 3.9KΩ1/4W D4 FR107 D5 FR107 OSC1-3Ts OSC1-3Ts OSC1-4Ts C8 C3 X1 0.1UF/275AC C5 CD 22UF/200V C4 CD 22UF/200V 473/50V D10 FR107 D1 L1 C2 X1 0.1UF/275AC D6 1N4007 L4 10uH 1/2W D7 1N4007 L5 10uH 1/2W C9 CBB22 0.1UF/400V C11 1N4007 Φ 10 x12 M M Φ 0.31mm 180T L>1mH RLF NH-2A-14W(T5) 1 2 34 A BC D 4 3 2 1 D CB A Sheet Name Des ign Dr awing Review Ve r sion Re vision Compa ny Na me ZHOUG SHAN SAUNTER ELECTRIC CO.,LED Dat e Design department E ngine er ing De par t me nt 1.0 1st 2011/03/20 Jiesen Zhou Jiesen Zhou Jiesen Zhou Product Name L3 120V 2A/250V FUSE 120V VR1 7D271K 1N4007 D2 Q1 MJE13003 (T O-220) C6 CBB22 152J/630V R3 RY 680KΩ 1Ws R1 RY 100KΩ 1W R5 RY 1.5Ω 1/4W Q2 MJE13003 (TO-220) R7 RY 1.5Ω1/4W RY 680KΩ 1W s R2 SCR1 MCR100-6 RY 22Ω1/2 Ws R4 D8 1N4007 D9 1N4007 R6 RY 22Ω1/2 Ws C7 CL11 0.022uF/100V D3 1N4007 TD1 DB3 T5 21W OSC 10x6X5 L6 Φ 0.15mm 25Ts L7 Φ0.23mm 132Ts L6,L7,L8=2.1-2.2mH CBB22 472J/1250V D11 FR107 PTC1 WMZ11B105S471N7D301K Q3 S9014 R12 RT 560Ω1/4 W R11 RT 56 Ω 1/4W R8 RT 1 5K Ω 1/ 4 W D12 FR107 C10 47uF/50V R9 RT 270KΩ1/4W LN C1 Y1 472M/250V GND L2 EE13Common mode L1= L2> 20 mH Φ 0. 3 1 mm 60 T sX2 TD2 DB3 R10 RT 3.9KΩ1/4W D4 FR107 D5 FR107 OSC1-4Ts OSC1-4Ts OSC1-3Ts C8 L8 C3 X1 0.2UF/275AC C5 CD 22UF/200V C4 CD 22UF/200V 473/50V D10 FR107 D1 L1 C2 X1 0.2UF/275AC D6 1N4007 L4 10uH 1/2W D7 1N4007 L5 10uH 1/2W C9 CBB22 0.1UF/400V C11 1N4007 Φ 10 x12 M M Φ 0.31mm 180T L>1mH RLF NH-2A-21W(T5) 1 2 34 A BC D 4 3 2 1 D CB A Sheet Name Des ign Dr awing Review Ve r sion Re vision Compa ny Na me ZHOUG SHAN SAUNTER ELECTRIC CO.,LED Dat e Design department E ngine er ing De par t me nt 1.0 1st 2011/03/20 Jiesen Zhou Jiesen Zhou Jiesen Zhou Product Name L3 120V 2A/250V FUSE 120V VR1 7D271K 1N4007 D2 Q1 MJE13005 (T O-220) C6 CBB22 152J/630V R3 RY 680KΩ 1Ws R1 RY 100KΩ 1W R5 RY 1Ω 1/4W Q2 MJE13005 (TO-220) R7 RY 1Ω1/4W RY 680KΩ 1W s R2 SCR1 MCR100-6 RY 22Ω1/2 Ws R4 D8 1N4007 D9 1N4007 R6 RY 22Ω1/2 Ws C7 CL11 0.022uF/100V D3 1N4007 TD1 DB3 T5 28W OSC 10x6X5 L6 Φ 0.15mm 25Ts L7 Φ0.23mm 132Ts L6,L7,L8=1.8-1.9mH CBB22 472J/1250V D11 FR107 PTC1 WMZ11B105S471N7D301K Q3 S9014 R12 RT 560Ω1/4 W R11 RT 56 Ω 1/4W R8 RT 1 5K Ω 1/ 4 W D12 FR107 C10 47uF/50V R9 RT 270KΩ1/4W LN C1 Y1 472M/250V GND L2 EE13Common mode L1= L2> 20 mH Φ 0.31mm 60TsX2 TD2 DB3 R10 RT 3.9KΩ1/4W D4 FR107 D5 FR107 OSC1-4Ts OSC1-4Ts OSC1-3Ts C8 L8 C3 X1 0.2UF/275AC C5 CD 22UF/200V C4 CD 22UF/200V 473/50V D10 FR107 D1 L1 C2 X1 0.2UF/275AC D6 1N4007 L4 10uH 1/2W D7 1N4007 L5 10uH 1/2W C9 CBB22 0.1UF/400V C11 1N4007 Φ 10 x12 M M Φ 0.31mm 180T L>1mH RLF NH-2A-28W(T5) 1 2 34 A BC D 4 3 2 1 D CB A Sheet Name Des ign Dr awing Review Ve r sion Re vision Compa ny Na me ZHOUG SHAN SAUNTER ELECTRIC CO.,LED Dat e Design department E ngine er ing De par t me nt 1.0 1st 2011/03/20 Jiesen Zhou Jiesen Zhou Jiesen Zhou Product Name L3 120V 2A/250V FUSE 120V VR1 7D271K 1N4007 D2 Q1 MJE13005 (T O-220) C6 CBB22 152J/630V R3 RY 680KΩ 1Ws R1 RY 100KΩ 1W R5 RY 1Ω 1/4W Q2 MJE13005 (TO-220) R7 RY 1Ω1/4W RY 680KΩ 1W s R2 SCR1 MCR100-6 RY 22Ω1/2 Ws R4 D8 1N4007 D9 1N4007 R6 RY 22Ω1/2 Ws C7 CL11 0.022uF/100V D3 1N4007 TD1 DB3 T5 35W OSC 10x6X5 L6 Φ 0.15mm 25Ts L7 Φ0.23mm 132Ts L6,L7,L8=2.0-2.1mH CBB22 562J/1250V D11 FR107 PTC1 WMZ11B105S471N7D391K Q3 S9014 R12 RT 560Ω1/4 W R11 RT 56 Ω 1/4W R8 RT 1 5K Ω 1/ 4 W D12 FR107 C10 47uF/50V R9 RT 270KΩ1/4W LN C1 Y1 472M/250V GND L2 EE13Common mode L1= L2> 20 mH Φ 0.31mm 60TsX2 TD2 DB3 R10 RT 3.9KΩ1/4W D4 FR107 D5 FR107 OSC1-4Ts OSC1-4Ts OSC1-4Ts C8 L8 C3 X1 0.2UF/275AC C5 CD 33UF/200V C4 CD 33UF/200V 473/50V D10 FR107 D1 L1 C2 X1 0.2UF/275AC D6 1N4007 L4 10uH 1/2W D7 1N4007 L5 10uH 1/2W C9 CBB22 0.1UF/400V C11 1N4007 Φ 10 x12 M M Φ 0.31mm 180T L>1mH RLF NH-2A-35W(T5) 1 2 34 A BC D 4 3 2 1 D CB A Sheet Name Des ign Dr awing Review Ve r sion Re vision Compa ny Na me ZHOUG SHAN SAUNTER ELECTRIC CO.,LED Dat e Design department E ngine er ing De par t me nt 1.0 1st 2011/03/20 Jiesen Zhou Jiesen Zhou Jiesen Zhou Product Name L3 120V 2A/250V FUSE 120V VR1 7D271K 1N4007 D2 Q1 MJE13005 (T O-220) C6 CBB22 152J/630V R3 RY 680KΩ 1Ws R1 RY 100KΩ 1W R5 RY 1Ω 1/4W Q2 MJE13005 (TO-220) R7 RY 1Ω1/4W RY 680KΩ 1W s R2 SCR1 MCR100-6 RY 22Ω1/2 Ws R4 D8 1N4007 D9 1N4007 R6 RY 22Ω1/2 Ws C7 CL11 0.022uF/100V D3 1N4007 TD1 DB3 T4 28W OSC 10x6X5 L6 Φ 0.15mm 25Ts L7 Φ0.23mm 132Ts L6,L7,L8=2.15-2.25mH CBB22 472J/1250V D11 FR107 PTC1 WMZ11B105S471N7D391K Q3 S9014 R12 RT 560Ω1/4 W R11 RT 56 Ω 1/4W R8 RT 1 5K Ω 1/ 4 W D12 FR107 C10 47uF/50V R9 RT 270KΩ1/4W LN C1 Y1 472M/250V GND L2 EE13Common mode L1= L2> 20 mH Φ 0.31mm 60TsX2 TD2 DB3 R10 RT 3.9KΩ1/4W D4 FR107 D5 FR107 OSC1-4Ts OSC1-4Ts OSC1-3Ts C8 L8 C3 X1 0.2UF/275AC C5 CD 22UF/200V C4 CD 22UF/200V 473/50V D10 FR107 D1 L1 C2 X1 0.2UF/275AC D6 1N4007 L4 10uH 1/2W D7 1N4007 L5 10uH 1/2W C9 CBB22 0.1UF/400V C11 1N4007 Φ 10 x12 M M Φ 0.31mm 180T L>1mH RLF NH-2A-28W(T4) 1 2 34 A BC D 4 3 2 1 D CB A Sheet Name Des ign Dr awing Review Ve r sion Re vision Compa ny Na me ZHOUG SHAN SAUNTER ELECTRIC CO.,LED Dat e Design department E ngine er ing De par t me nt 1.0 1st 2011/03/20 Jiesen Zhou Jiesen Zhou Jiesen Zhou Product Name L3 120V 2A/250V FUSE 120V VR1 7D…

Text truncated - open the document above for the full version.

Note: This test report is prepared for the customer shown above and for the equipment described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, or any agency of the Federal Government. * This report contains data that are not covered by the NVLAP accreditation and are marked with an asterisk “★” (Rev.2) FCC PART 18 TEST REPORT For ZHONGSHAN SAUNTER ELECTRIC CO., LTD. No16, LeFeng2 Road, the MaoHui Industrial Area of HengLan Town, Zhongshan City, GuangDong, China FCC ID: ZJZSAUNTER Report Type: Original Report Product Type: RLF Test Engineer: Andy Xiong Report Number: RSZ11011051 Report Date: 2011-07-19 Reviewed By: Lisa Zhu EMC Engineer Test Laboratory: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong,China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ11011051 FCC Part 18 Page 2 of 25 TABLE OF CONTENTS GENERAL INFORMATION.......................................................................................................................................3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................3 OBJECTIVE...................................................................................................................................................................3 RELATED SUBMITTAL(S)/GRANT(S).............................................................................................................................3 TEST METHODOLOGY..................................................................................................................................................3 TEST FACILITY.............................................................................................................................................................3 SYSTEM TEST CONFIGURATION ..........................................................................................................................5 JUSTIFICATION.............................................................................................................................................................5 EUT EXERCISE SOFTWARE..........................................................................................................................................5 SPECIAL ACCESSORIES.................................................................................................................................................5 EQUIPMENT MODIFICATIONS.......................................................................................................................................5 EXTERNAL I/O CABLE..................................................................................................................................................5 CONFIGURATION OF TEST SETUP.................................................................................................................................5 BLOCK DIAGRAM OF TEST SETUP................................................................................................................................6 FCC §18.307 - AC LINE CONDUCTED EMISSIONS..............................................................................................7 APPLICABLE STANDARD..............................................................................................................................................7 MEASUREMENT UNCERTAINTY....................................................................................................................................7 EUT SETUP..................................................................................................................................................................7 EMI TEST RECEIVER SETUP.........................................................................................................................................8 TEST PROCEDURE........................................................................................................................................................8 TEST EQUIPMENT LIST AND DETAILS...........................................................................................................................8 TEST RESULTS SUMMARY............................................................................................................................................8 TEST DATA..................................................................................................................................................................9 FCC §18.305 – FIELD STRENGTH..........................................................................................................................21 MEASUREMENT UNCERTAINTY..................................................................................................................................21 EUT SETUP................................................................................................................................................................21 EMI TEST RECEIVER SETUP AND SPECTRUM ANALYZER SETUP................................................................................22 TEST PROCEDURE......................................................................................................................................................22 CORRECTED AMPLITUDE CALCULATION....................................................................................................................22 TEST EQUIPMENT LIST AND DETAILS.........................................................................................................................22 TEST DATA...........…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Model: NH-2A-30W (T4) Conducted Emissions - Front View Conducted Emissions - Side View Radiated Emissions - Front View Radiated Emissions - Rear View Model: NH-2A-28W (T4) Conducted Emissions - Front View Conducted Emissions - Side View Radiated Emissions - Front View Radiated Emissions - Rear View Model: NH-2A-28W (T5) Conducted Emissions - Front View Conducted Emissions - Side View Radiated Emissions - Front View Radiated Emissions - Rear View Model: NH-2A-21W (T5) Conducted Emissions - Front View Conducted Emissions - Side View Radiated Emissions - Front View Radiated Emissions - Rear View Model: NH-2A-14W (T5) Conducted Emissions - Front View Conducted Emissions - Side View Radiated Emissions - Front View Radiated Emissions - Rear View Model: NH-2A-35W (T5) Conducted Emissions - Front View Conducted Emissions - Side View Radiated Emissions - Front View Radiated Emissions - Rear View