ZK7SSERIESGPS CONTROLLER (GPS RECEIVER)

Rugged Portable Solutions S SERIES USER MANUAL ENERGY STAR ® is a government program that offers businesses and consumers energy-efficient solutions, making it easy to save money while protecting the environment for future generations. Please reference ENERGY STAR ® related information from www.energystar.gov. BAP Precision LTD. has determined that this product meets the ENERGY STAR ® guidelines for energy efficiency. An ENERGY STAR ® qualified computer uses 70 % less electricity than computers without enabled power management features. Earning the Earning the Earning the Earning the E EE ENERGY NERGY NERGY NERGY S SS STAR TARTAR TAR ® ®® ®
When every home office is powered by equipment that has earned the ENERGY STAR ® , the change will keep over 289 billion pounds of greenhouse gases out of the air.
If left inactive, ENERGY STAR ® qualified computers enter a low-power mode and may use 15 watts or less. New chip technologies make power management features more reliable, dependable, and user-friendly than even just a few years ago.
Spending a large portion of time in low-power mode not only saves energy, but helps equipment run cooler and last longer.
Businesses that use ENERGY STAR ® enabled office equipment may realize additional savings on air conditioning and maintenance.
Over its lifetime, ENERGY STAR ® qualified equipment in a single home office (e.g., computer, monitor, printer, and fax) can save enough electricity to light an entire home for more than 4 years.
Power management (“sleep settings”) on computers and monitors can result in much savings annually. Remember, saving energy prevents pollution Remember, saving energy prevents pollutionRemember, saving energy prevents pollution Remember, saving energy prevents pollution Because most computer equipment is left on 24 hours a day, power management features are important for saving energy and are an easy way to reduce air pollution. By using less energy, these products help lower consumers’ utility bills, and prevent greenhouse gas emissions. i Table of Contents Table of ContentsTable of Contents Table of Contents Chapter 1 Chapter 1Chapter 1 Chapter 1 G GG Getting Started etting Startedetting Started etting Started ................................ ................................................................ ................................................................ ................................................................ ................................................................ ................................................................ .............................................. ............................ .............. 1 11 1- -- -1 11 1 Identifying Hardware Components ..................................... 1-1 Front Components ..................................................... 1-1 Back Components ..................................................... 1-4 Bottom Components ................................................... 1-5 Connecting to AC Power and Charging the Battery.......... 1-6 Performing the Initial Startup ....................................... 1-6 Synchronizing with Your Computer .................................... 1-7 Installing ActiveSync or WMDC .................................... 1-8 Using Options .............................................................. 1-9 Using an SD Card .................................................... 1-9 Chapter ChapterChapter Chapter 2 22 2 B BB Basic Skills asic Skillsasic Skills asic Skills ................................ ................................................................ ................................................................ ................................................................ ................................................................ ................................................................ .................................................... ........................................ .................... 2 22 2- -- -1 11 1 Power Saving and Turning Off ........................................ 2-1 Backlight Off ............................................................ 2-1 Entering the Suspend Mode ........................................ 2-1 Turning Off ..............................................................2-2 Navigating on the Screen ...............................................2-2 Stylus .....................................................................2-2 Today Screen ..............................................................2-3 Landscape View ........................................................2-3 Navigation Bar and Toolbar ............................................2-3 ii Programs ....................................................................2-4 Notifications .................................................................2-4 Entering Information .......................................................2-5 Entering Text Using the Input Panel .............................2-5 Writing on the Screen ...............................................2-6 Drawing on the Screen ..............................................2-6 Recording a Message ................................................2-7 Using My Text .........................................................2-8 Securing Your Device ....................................................2-8 Locking the Keypad ...................................................2-8 Locking Your Device ..................................................2-8 Chapter ChapterChapter Chapter 3 33 3 U UU Using the Phone (Select Models Only) sing the Phone (Select Models Only)sing the Phone (Select Models Only) sing the Phone (Select Models Only) ................................ ................................................................ ............................................................. .......................................................... ............................. 3 33 3- -- -1 11 1 About Your Pho…

Text truncated - open the document above for the full version.

BAP CISlon Ltd. 1F, NO.5. Ln. 1 ,Chengzhang 1 st 8t., Zhongli County 320, Taiwan . +886-3-4516986 FAX: +886-3-4518067 May 20, 2010 Federal Communications Commission Authorization and Evaluation Division FCC ID : ZK7SSERIES Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission's Rules, the applicant hereby requests confidential treatment of information applied this application as outlined below: 1. Block Diagram 2. Circuit Diagram 3. Operational Description 4. Power Tune up procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application Sincerely, Signature -----'=------7/"==-------=------­ Name/Title: Brandon Wu / Managing Director Company Name: BAP Precision Ltd. Address: IF., No.5, Ln. 147,Chengzhang 1st St., Zhongli City, Taoyuan County 320, Taiwan TEL: +886-3-4516986 FAX: +886-3-4518067 Email: [email protected]

Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: May, 20, 2011 SUBJECT: FCC Application for ZK7SSERIES To Whom It May Concern: We, the undersigned, hereby attest to the fact that we will apply the Declaration of Conformity procedure to the class B computer peripheral portion ofthis composite filing. Regards, Signature----'-"~~"""'""~~- Name/Title: Brandon Wu / Managing Director Company Name: BAP Precision Ltd. Address: iF., No.5, Ln. 147,Chengzhang 1st St., Zhongli City, Taoyuan County 320, Taiwan TEL: +886-3-4516986 FAX: +886-3-4518067 Email: [email protected]

Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 10 INTERNAL PHOTOGRAPHS OF EUT Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 11 Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 12 Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 13 Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 14 Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 15 Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 16 Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 17 Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 18 Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 19 Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 20 Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 21 Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 22 Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 23 Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 24 For M30 Module Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 25 For Battery Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 26 For Antenna For Bluetooth For GPS Compliance Certification Services Inc. Report No.: T110414001 Date of Issue: May 11, 2011 A1 - 27 For WLAN For 2G & 3G

BAP / S SERIES Antenna spec. Manufacturer: GSM/BT/WLAN: Cirocomm Propriety information GSM Antenna Frequency: 824-890MHz, 880-960MHz, 1710-1880MHz, 1850-1990MHz, 2110-2170MHz Band: Qual-band, GSM850, EGSM900, DCS1800, PCS1900, WCDMA Band II, WCDMA Band V Peak gain: 0.83dB@GSM850, -0.29dB@GSM900, 2.54dB@GSM1800, 2.35dB@GSM1900, 2.35dB@WCDMA Band II, 0.83dB@WCDMA Band V Antenna type: PCB Antenna drawing: 03C00E030000140 3D Radiation Pattern 824MHz 890MHz 880MHz 960MHz 1710MHz 1880MHz 1850MHz 1990MHz 2110MHz 2170MHz Bluetooth antenna Operating frequency : 2400-2484MHz Band: WIFI Peak gain : -0.64dBi Antenna type : PIFA Antenna drawing: PPA2442E 3D Radiation Pattern 2400 MHz 2442 MHz 2484 MHz WIFI antenna Operating frequency : 2400-2500MHz Band: WIFI Peak gain : 1.45dBi Antenna type : PIFA Antenna drawing: MPA2450B 3D Radiation Pattern 2400 MHz 2450 MHz 2500 MHz

Date/Time: 2011/05/06 09:28:40 AM Test Laboratory: Compliance Certification Services Inc. GPRS 850 - Body BT730 DUT: BT730; Type: BT730; Serial: n/a Communication System: GPRS 850; Frequency: 836.6 MHz;Duty Cycle: 1:4 Medium parameters used (interpolated): f = 836.6 MHz; σ = 0.942 mho/m; ε r = 54.1; ρ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.6 deg C;Liquid Temperature:23.6 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: Probe: EX3DV4 - SN3665; ConvF(9.5, 9.5, 9.5); Sensor-Surface: 2.5mm (Mechanical Surface Detection) Electronics: DAE4 Sn877; Calibrated: 2011/3/18 Phantom: ELI 4.0; Type: QDOVA001BA; Serial: 1056 Measurement SW: DASY5, V5.0 Build 125; Postprocessing SW: SEMCAD, V1.8 Build 186 GPRS Front Middle CH190/Area Scan (7x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.342 mW/g GPRS Front Middle CH190/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 13.1 V/m; Power Drift = -0.032 dB Peak SAR (extrapolated) = 0.447 W/kg SAR(1 g) = 0.278 mW/g; SAR(10 g) = 0.182 mW/g Maximum value of SAR (measured) = 0.340 mW/g GPRS Front Middle CH190/Zoom Scan (7x7x9)/Cube 1: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 13.1 V/m; Power Drift = -0.032 dB Peak SAR (extrapolated) = 0.361 W/kg SAR(1 g) = 0.247 mW/g; SAR(10 g) = 0.176 mW/g Maximum value of SAR (measured) = 0.314 mW/g Date/Time: 2011/05/06 10:25:05 AM Test Laboratory: Compliance Certification Services Inc. GPRS 850 - Body BT730 DUT: BT730; Type: BT730; Serial: n/a Communication System: GPRS 850; Frequency: 824.2 MHz;Duty Cycle: 1:4 Medium parameters used (interpolated): f = 824.2 MHz; σ = 0.931 mho/m; ε r = 54.3; ρ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.6 deg C;Liquid Temperature:23.6 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: Probe: EX3DV4 - SN3665; ConvF(9.5, 9.5, 9.5); Sensor-Surface: 2.5mm (Mechanical Surface Detection) Electronics: DAE4 Sn877; Calibrated: 2011/3/18 Phantom: ELI 4.0; Type: QDOVA001BA; Serial: 1056 Measurement SW: DASY5, V5.0 Build 125; Postprocessing SW: SEMCAD, V1.8 Build 186 GPRS Back Low CH128/Area Scan (7x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.939 mW/g GPRS Back Low CH128/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 32.0 V/m; Power Drift = -0.023 dB Peak SAR (extrapolated) = 1.08 W/kg SAR(1 g) = 0.824 mW/g; SAR(10 g) = 0.607 mW/g Maximum value of SAR (measured) = 0.935 mW/g Date/Time: 2011/05/06 09:58:09 AM Test Laboratory: Compliance Certification Services Inc. GPRS 850 - Body BT730 DUT: BT730; Type: BT730; Serial: n/a Communication System: GPRS 850; Frequency: 836.6 MHz;Duty Cycle: 1:4 Medium parameters used (interpolated): f = 836.6 MHz; σ = 0.942 mho/m; ε r = 54.1; ρ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.6 deg C;Liquid Temperature:23.6 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: Probe: EX3DV4 - SN3665; ConvF(9.5, 9.5, 9.5); Sensor-Surface: 2.5mm (Mechanical Surface Detection) Electronics: DAE4 Sn877; Calibrated: 2011/3/18 Phantom: ELI 4.0; Type: QDOVA001BA; Serial: 1056 Measurement SW: DASY5, V5.0 Build 125; Postprocessing SW: SEMCAD, V1.8 Build 186 GPRS Back Middle CH190/Area Scan (7x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 1.01 mW/g GPRS Back Middle CH190/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 33.1 V/m; Power Drift = -0.009 dB Peak SAR (extrapolated) = 1.12 W/kg SAR(1 g) = 0.873 mW/g; SAR(10 g) = 0.642 mW/g Maximum value of SAR (measured) = 0.993 mW/g Date/Time: 2011/05/06 10:51:33 AM Test Laboratory: Compliance Certification Services Inc. GPRS 850 - Body BT730 DUT: BT730; Type: BT730; Serial: n/a Communication System: GPRS 850; Frequency: 848.8 MHz;Duty Cycle: 1:4 Medium parameters used (interpolated): f = 848.8 MHz; σ = 0.953 mho/m; ε r = 54; ρ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.6 deg C;Liquid Temperature:23.6 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: Probe: EX3DV4 - SN3665; ConvF(9.5, 9.5, 9.5); Sensor-Surface: 2.5mm (Mechanical Surface Detection) Electronics: DAE4 Sn877; Calibrated: 2011/3/18 Phantom: ELI 4.0; Type: QDOVA001BA; Serial: 1056 Measurement SW: DASY5, V5.0 Build 125; Postprocessing SW: SEMCAD, V1.8 Build 186 GPRS Back High CH251/Area Scan (7x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 1.08 mW/g GPRS Back High CH251/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 34.0 V/m; Power Drift = -0.028 dB Peak SAR (extrapolated) = 1.22 W/kg SAR(1 g) = 0.951 mW/g; SAR(10 g) = 0.693 mW/g Date/Time: 2011/05/06 11:24:22 AM Test Laboratory: Compliance Certification Services Inc. EGPRS 850 - Body BT730 DUT: BT730; Type: BT730; Serial: n/a Communication System: EGPRS 850; Frequency: 824.2 MHz;Duty Cycle: 1:4 Medium parameters used (interpolated): f = 824.2 MHz; σ = 0.931 mho/m; ε r = 54.3; ρ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.6 deg C;Liquid Temperature:23.6 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: Probe: EX3DV4 - SN3665; ConvF(9.5, 9.5, 9.5); Sensor-Surface: 2.5mm (Mechanical Surface Detection) Electronics: DAE4 Sn877; Calibrated: 2011/3/18 Phantom: ELI 4.0; Type: QDOVA001BA; Serial: 1056 Measurement SW: DASY5, V5.0 Build 125; Postprocessing SW: SEMCAD, V1.8 Build 186 EGPRS Front Low CH128/Area Scan (7x8x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.091 mW/g EGPRS Front Low CH128/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Report No: T110414001-SF FCC ID: ZK7SSERIES Date of Issue: May 10, 2011 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 Total Page: 38 Rev. 00 ANSI/IEEE Std. C95.1-1992 In accordance with the requirements of FCC Report and Order: ET Docket 93-62, and OET Bulletin 65 Supplement C FCC SAR TEST REPORT For GPS Controller Model: S SERIES Trade Name: BAP Issued to BAP Precision Ltd. 1F., No. 5, Ln. 147, Chengzhang 1st St., Zhongli City, Taoyuan County 320, Taiwan, R.O.C. Issued by Compliance Certification Services Inc. No. 11, Wugong 6th Rd., Wugu Industrial Park, Taipei Hsien, 248 Taiwan. http://www. ccsrf.com [email protected] Compliance Certification Services Inc. Report No: T110414001-SF Date of Issue: May 10, 2011 Page 2 Rev. 00 Revision History Rev Issue Date Revisions Revised By 00 May 10, 2011 Initial Issue Peach Chang Compliance Certification Services Inc. Report No: T110414001-SF Date of Issue: May 10, 2011 Page 3 Rev. 00 TABLE OF CONTENTS 1. CERTIFICATE OF COMPLIANCE (SAR EVALUATION) .........................................................4 2. EUT DESCRIPTION ..........................................................................................................................5 3. REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE FCC ..........................6 4. DOSIMETRIC ASSESSMENT SETUP ............................................................................................6 4.1 MEASUREMENT SYSTEM DIAGRAM.....................................................................................7 4.2 SYSTEM COMPONENTS ............................................................................................................8 5. EVALUATION PROCEDURES......................................................................................................11 6. MEASUREMENT UNCERTAINTY ..............................................................................................15 7. EXPOSURE LIMIT ..........................................................................................................................17 8. EUT ARRANGEMENT....................................................................................................................18 8.1 ANTHROPOMORPHIC HEAD PHANTOM .............................................................................18 8.2 DEFINITION OF THE “CHEEK/TOUCH” POSITION ............................................................19 8.3 DEFINITION OF THE “TILTED” POSITION...........................................................................20 9. MEASUREMENT RESULTS ..........................................................................................................21 9.1 TEST LIQUIDS CONFIRMATION............................................................................................21 9.2 SYSTEM PERFORMANCE CHECK .........................................................................................23 9.3 EUT TUNE-UP PROCEDURES .................................................................................................25 9.4 SAR MEASUREMENT RESULTS ............................................................................................31 10. EUT PHOTO .................................................................................................................................35 11. EQUIPMENT LIST & CALIBRATION STATUS.....................................................................36 12. FACILITIES ..................................................................................................................................37 13. REFERENCES ..............................................................................................................................37 14. ATTACHMENTS..........................................................................................................................38 Compliance Certification Services Inc. Report No: T110414001-SF Date of Issue: May 10, 2011 Page 4 Rev. 00 1. CERTIFICATE OF COMPLIANCE (SAR EVALUATION) Applicant: BAP Precision Ltd. 1F., No. 5, Ln. 147, Chengzhang 1st St., Zhongli City, Taoyuan County 320, Taiwan, R.O.C. Equipment Under Test: GPS Controller Trade Name: BAP Model Number: S SERIES Date of Test: May 05 ~ 07, 2011 Device Category: PORTABLE DEVICES Exposure Category: GENERAL POPULATION/UNCONTROLLED EXPOSURE APPLICABLE STANDARDS STANDARD TEST RESULT FCC OET 65 Supplement C No non-compliance noted Deviation from Applicable Standard None The device was tested by Compliance Certification Services Inc. in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C(Edition 01-01). The test results in this report apply only to the tested sample of the stated device/equipment. Other similar device/equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Approved by: Tested by: Rex Lai Anson Lu Section Manager Test Engineer Compliance Certification Services Inc. Compliance Certification Services Inc Compliance Certification Services Inc. Report No: T110414001-SF Date of Issue: May 10, 2011 Page 5 Rev. 00 2. EUT DESCRIPTION Product GPS Controller Model Number S SERIES Trade Name BAP Model Discrepancy N/A Frequency Range GPRS / EGPRS: 850: 824.2 ~ 848.8 MHz GPRS / EGPRS: 1900: 1850.2 ~ 1909.8 MHz WCDMA / HSDPA band V: 826.4 ~ 846.6 MHz WCDMA / HSDPA band II: 1852.4 ~ 1907.6 MHz 802.11b / g: 2412 ~ 2462 MHz Bluetooth: 2402 ~ 2480 MHz 850 Band: GPRS 850: 24.79 dBm EDGE850: 21.38 dBm WCDMA band V: 24.10 dBm HSDPA band V: 23.56 dBm 1900 Band: GPRS 1900: 22.39 dBm EDGE1900: 20.70 dBm WCDMA band II: 23.74 dBm HSDPA band II: 23.12 dBm Transmit Power(Average) 2.4GHz: 802.11b: 18.46 dBm 802.11g…

Text truncated - open the document above for the full version.

Date/Time: 2011/05/06 08:17:25 AM Test Laboratory: Compliance Certification Services Inc. D835V2-SN 4d015-Body DUT: Dipole 835 MHz; Type: D835V2; Serial: 4d015 Communication System: CW 835; Frequency: 835 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 835 MHz; σ = 0.941 mho/m; ε r = 54.1; ρ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.6 deg C;Liquid Temperature:23.6 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: lProbe: EX3DV4 - SN3665; ConvF(9.5, 9.5, 9.5); lSensor-Surface: 2.5mm (Mechanical Surface Detection) lElectronics: DAE4 Sn877; Calibrated: 2011/3/18 lPhantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN: 1052 lMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 d=15mm, Pin=250mW/Area Scan (7x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 3.19 mW/g d=15mm, Pin=250mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 56 V/m; Power Drift = -0.065 dB Peak SAR (extrapolated) = 3.58 W/kg SAR(1 g) = 2.45 mW/g; SAR(10 g) = 1.66 mW/g Maximum value of SAR (measured) = 3.17 mW/g d=15mm, Pin=250mW/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Maximum value of SAR (measured) = 3.17 mW/g Date/Time: 2011/05/05 08:57:34 AM Test Laboratory: Compliance Certification Services Inc. D1900V2 SN-5d056 Body DUT: Dipole 1900 MHz; Type: D1900V2; Serial: 5d056 Communication System: PCS 1900; Frequency: 1900 MHz;Duty Cycle: 1:1 Medium parameters used: f = 1900 MHz; σ = 1.53 mho/m; ε r = 54.3; ρ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.6 deg C;Liquid Temperature:23.6 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: lProbe: EX3DV4 - SN3665; ConvF(8.06, 8.06, 8.06); lSensor-Surface: 2.5mm (Mechanical Surface Detection) lElectronics: DAE4 Sn877; Calibrated: 2011/3/18 lPhantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN: 1052 lMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Pin=250mW,d=10mm/Area Scan (6x6x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 9.70 mW/g Pin=250mW,d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 96.V/m; Power Drift = -0.025 dB Peak SAR (extrapolated) = 20.5 W/kg SAR(1 g) = 10.0 mW/g; SAR(10 g) = 5.12 mW/g Maximum value of SAR (measured) = 13.4 mW/g Pin=250mW,d=10mm/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Maximum value of SAR (measured) = 13.4 mW/g Date/Time: 2011/05/07 09:21:13 AM Test Laboratory: Compliance Certification Services Inc. D2450V2 SN-72 Body DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 - SN:72 Communication System: CW2450; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2450 MHz; σ = 1.97 mho/m; ε r = 52.5; ρ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.6 deg C;Liquid Temperature:23.6 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: lProbe: EX3DV4 - SN3665; ConvF(7.47, 7.47, 7.47); lSensor-Surface: 2.5mm (Mechanical Surface Detection) lElectronics: DAE4 Sn558; Calibrated: 2010/7/14 lPhantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN: 1052 lMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Pin=250mW,d=10mm/Area Scan (6x6x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 14.2 mW/g Pin=250mW,d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 97.2 V/m; Power Drift = -0.062 dB Peak SAR (extrapolated) = 27.5 W/kg SAR(1 g) = 1.1 mW/g; SAR(10 g) = 6.17 mW/g Maximum value of SAR (measured) = 18.8 mW/g Pin=250mW,d=10mm/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Maximum value of SAR (measured) = 19.2 mW/g

Compliance Certification Services Inc. FCC ID: ZK7SSERIES Report No.: T110414001-RP2 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 / 63 FCC 47 CFR PART 15 SUBPART C TEST REPORT For GPS controller (GPS Receiver) Model: S SERIES Trade Name: BAP Issued to BAP Precision Ltd. 1F., No. 5, Ln. 147, Chengzhang 1st St., Zhongli City, Taoyuan County 320, Taiwan, R.O.C. Issued by Compliance Certification Services Inc. No. 11, Wu-Gong 6 th Rd., Wugu Industrial Park, Taipei Hsien 248, Taiwan (R.O.C.) http://www.ccsrf.com [email protected] Issued Date: May 19, 2011 Compliance Certification Services Inc. FCC ID: ZK7SSERIES Report No.: T110414001-RP2 Page 2 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 May 19, 2011 Initial Issue ALL Sandy Lin Compliance Certification Services Inc. FCC ID: ZK7SSERIES Report No.: T110414001-RP2 Page 3 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION....................................................................................................4 2. EUT DESCRIPTION ...........................................................................................................................5 3. TEST METHODOLOGY ....................................................................................................................6 3.1 EUT CONFIGURATION........................................................................................................................6 3.2 EUT EXERCISE....................................................................................................................................6 3.3 GENERAL TEST PROCEDURES.............................................................................................................6 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS.........................................................7 3.5 DESCRIPTION OF TEST MODES...........................................................................................................8 4. INSTRUMENT CALIBRATION........................................................................................................9 4.1 MEASURING INSTRUMENT CALIBRATION......................................................................................9 4.2 MEASUREMENT EQUIPMENT USED .........................................................................................9 4.3 MEASUREMENT UNCERTAINTY .............................................................................................10 5. FACILITIES AND ACCREDITATIONS ........................................................................................11 5.1 FACILITIES.......................................................................................................................................11 5.2 EQUIPMENT......................................................................................................................................11 5.3 TABLE OF ACCREDITATIONS AND LISTINGS.....................................................................................12 6. SETUP OF EQUIPMENT UNDER TEST .......................................................................................13 6.1 SETUP CONFIGURATION OF EUT....................…

Text truncated - open the document above for the full version.