ZNFH443GSM/WCDMA/LTE PHONE + BLUETOOTH, DTS/UNII a/b/g/n & NFC

Product Safety & Warranty Information This booklet is made from 60% post-consumer recycled paper. This booklet is printed with soy ink. ©All Rights Reserved.Printed in China MBM64596801 (1.0) Información sobre la garantía y seguridad del producto LG-H443 1 Violation of the instructions may cause serious injury or death. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. ● Never use an unapproved battery since this could damage the phone and/or battery and could cause the battery to explode. ● Never place your phone in a microwave oven as it will cause the battery to explode. ● Never store your phone in temperatures less than -4°F or greater than 122°F. ● Do not dispose of your battery near fire or with hazardous or flammable materials. ● When riding in a car, do not leave your phone or set up the hands-free kit near the air bag. If wireless equipment is improperly installed and the air bag is deployed, you may be seriously injured. ● Do not use the phone in areas where its use is prohibited. (For example: aircraft) ● Do not expose the battery charger or adapter to direct sunlight or use it in places with high humidity, such as a bathroom. ● Do not use harsh chemicals (such as alcohol, benzene, thinners, etc.) or detergents to clean your phone. This could cause a fire. ● Do not drop, strike, or shake your phone severely. It may harm the internal circuit boards of the phone. 2 ● Do not use your phone in high explosive areas as the phone may generate sparks. ● Do not damage the power cord by bending, twisting, pulling, or heating. Do not use the plug if it is loose as it may cause electric shock or fire. ● Do not place any heavy items on the power cord. Do not allow the power cord to be crimped as it may cause electric shock or fire. ● Do not handle the phone with wet hands while it is being charged. It may cause an electric shock or seriously damage your phone. ● Do not disassemble the phone. ● Do not place or answer calls while charging the phone as it may short-circuit the phone and/or cause electric shock or fire. ● Do not hold or let the antenna come in contact with your body during a call. ● Make sure that no sharp-edged items, such as animal’s teeth or nails, come into contact with the battery. This could cause a fire. ● Store the battery out of reach of children. ● Be careful that children do not swallow any parts (such as earphone, connection parts of the phone, etc.) This could cause asphyxiation or suffocation resulting in serious injury or death. ● Unplug the power cord and charger during lightning storms to avoid electric shock or fire. ● Only use the batteries and chargers provided by LG. The warranty will not be applied to products provided by other suppliers. ● Only authorized personnel should service the phone and its accessories. Faulty installation or service may result in accidents and consequently invalidate the warranty. 3 ● An emergency call can be made only within a service area. For an emergency call, make sure that you are within a service area and that the phone is turned on. ● Your phone is an electronic device that generates heat during normal operation. Extremely prolonged, direct skin contact in the absence of adequate ventilation may result in discomfort or minor burns. Therefore, use care when handling your phone during or immediately after operation. HAC statement This phone has been tested and rated for use with hearing aids for some of the wireless technologies that it uses. However, there may be some newer wireless technologies used in this phone that have not been tested yet for use with hearing aids. It is important to try the different features of this phone thoroughly and in different locations, using your hearing aid or cochlear implant, to determine if you hear any interfering noise. Consult your service provider or the manufacturer of this phone for information on hearing aid compatibility. If you have questions about return or exchange policies, consult your service provider or phone retailer. FCC RF Exposure Information WARNING! Read this information before operating the phone. In August 1996, the Federal Communications Commission (FCC) of the United States, with its action in Report and Order FCC 96-326, adopted an updated safety standard for human exposure to Radio Frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of this phone complies with the FCC guidelines and these international standards. or by ts 4 to F D ind FD th a g co th us he at (88 W In Pr o sa wi te no ex of co Body-worn Operation This device was tested for typical body-worn operations with the back of the phone kept 0.39 inches (1cm) between the user’s body and the back of the phone. To comply with FCC RF exposure requirements, a minimum separation distance of 0.39 inches (1cm) must be maintained between the user’s body and the back of the phone. Third-party belt-clips, holsters, and similar accessories containing metallic components may not be used. Body-worn accessories that cannot maintain 0.39 inches (1cm) separation distance between the user’s body and the back of the phone, and have not been tested for typical body-worn operations may not comply with FCC RF exposure limits and should be avoided. Caution Use only the supplied antenna. Use of unauthorized antennas (or modifications to the antenna) could impair call quality, damage the phone, void your warranty and/or violate FCC regulations. Don't use the phone with a damaged antenna. A damaged antenna could cause a minor skin burn. Contact your local dealer for a replacement antenna. Consumer Information About Radio Frequency Emissions Your wireless phone, which contains a radio transmitter and receiver, emits radio frequency energy during use. The following…

Text truncated - open the document above for the full version.

Date: January 30, 2015 U L Verif ication Services Inc. Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc.as our agent, we still recognize that we are responsible to: a)comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d)do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e)upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f)use certification only to indicate the products are certified as being in conformity with specified standards; g)endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i)keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j)take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) doc ument the actions taken. T his authorization is valid until further written notice from the applicant. S incerely Yours, ____________________ J ongchul Lee Director On b ehalf of LG E lectronics Mobilecomm U.S.A.,Inc

Feder al Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia MD 21046 Subj ect: FCC ID: Request for Confidentiality ZNFH443 To W hom It May Concern: Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LG ELECTRONICS MobileComm USA hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG ELECTRONICS MobileComm USA temporary confidentiality of commercially sensitive information prior to product release. The r equested Permanent and Temporary Confidential exhibits are listed as follows: PERM ANENT AND SHORT-TERM CONFIDENTIAL LIST Exhibit Description PERMANENT 1 Block Diagram, Operational Descriptions and Tune-Up Procedure 2 Schematics, Part placement, and Part List 3 Antenna Specification SHORT-TERM 1 External Photos 2 Internal Photos 3 Test -Setup Photos 4 User’s Manual The A pplicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sinc erely Yours, Date: January 30, 2015 ____________________ Jongchul Lee Director On b ehalf of LG E lectronics Mobilecomm U.S.A.,Inc

※ FCC ID Label Form *Note: This label and its location complies with 47 CFR 2.925(d) that FCC ID is readily visible to the purchaser at the time of purchase, and be permanently affixed to the product. We, LG Electronics MobileComm USA, state that our device, FCC ID ZNH443, has a battery. However, the battery will not be placed in the battery compartment when delivery, so the label is visible to the users as they purchase the product and install the battery. Additionally, the label is permanently attached. The label it's attached to the EUT by an adhesive. The adhesive is a strong permanent type. Model No: LG-H443 FCC ID: ZNFH443 IM EI : XXXXXXXXX Made in Korea Model No: L G -H443 FCC ID: ZNF H443 Mad e in Korea Fig.1 Representation of FCC Label information

FCC ID: ZNFH443 Report No.: HCT-E-1501-F008 Page: 2 of 22 F-01P-02-014 (Rev.00) HCT CO., LTD DOCUMENT HISTORY The revision history for this document is shown in table. Version Date Description HCT-E-1501-F008 January 05, 2015 Initial Release FCC ID: ZNFH443 Report No.: HCT-E-1501-F008 Page: 3 of 22 F-01P-02-014 (Rev.00) HCT CO., LTD TABLE OF CONTENTS PAGE 1. GENERAL INFORMATION ....................................................................................................... 4 1.1 Description of EUT ................................................................................................................. 4 1.2 Related Submittal(s) / Grant(s)................................................................................................ 4 1.3 Test Facility ............................................................................................................................. 5 1.4 Tested System Details.............................................................................................................. 6 1.5 Cable Description .................................................................................................................... 7 1.6 Noise Suppression Parts on Cable. (I/O Cable) ...................................................................... 7 2. DESCRIPTION OF TEST ............................................................................................................ 8 3. PRELIMINARY TEST ............................................................................................................... 11 3.1 Conducted Emission Test ...................................................................................................... 11 3. 2 Radiated Emission Test ........................................................................................................ 11 4. CONDUCTED AND RADIATED EMISSION TEST SUMMARY ......................................... 12 4.1 Conducted Emission Test ...................................................................................................... 12 4.2 Radiated Emission Test ......................................................................................................... 19 5. LIST OF TEST EQUIPMENT ................................................................................................... 21 6. CONCLUSION .......................................................................................................................... 22 ATTACHMENT: TEST SETUP PHOTOGRAPHS FCC ID: ZNFH443 Report No.: HCT-E-1501-F008 Page: 4 of 22 F-01P-02-014 (Rev.00) HCT CO., LTD 1. GENERAL INFORMATION 1.1 Description of EUT Equipment Under Test is manufactured by LG Electronics MobileComm U.S.A., Inc. Its basic purpose is used for communications. Model LG-H443 FCC ID ZNFH443 Additional Model LGH443, H443 EUT Type Cellular/PCS GSM/WCDMA and LTE Phone with Bluetooth, WLAN and NFC TX Frequency 824.20 ㎒ to 848.80 ㎒ (GSM 850) 1 850.20 ㎒ to 1 909.80 ㎒ (GSM 1 900) 826.40 ㎒ to 846.60 ㎒ (WCDMA B5) 1 852.4 ㎒ to 1 907.6 ㎒ (WCDMA B2) 1712.4 ㎒ to 1752.6 ㎒ (WCDMA B4) 1 850.7 ㎒ to 1 909.3 ㎒ (LTE B2) 1 710 ㎒ to 1 755 ㎒ (LTE B4) 824 ㎒ to 849 ㎒ (LTE B5) 704 ㎒ to 716 ㎒ (LTE B17) RX Frequency 869.20 ㎒ to 893.80 ㎒ (GSM 850) 1 930.20 ㎒ to 1 989.80 ㎒ (GSM 1 900) 871.40 ㎒ to 891.60 ㎒ (WCDMA B5) 1 932.4 ㎒ to 1 987.6 ㎒ (WCDMA B2) 2 112.4 ㎒ to 2 152.6 ㎒ (WCDMA B4) 1 930.00 ㎒ to 1 990.00㎒ (LTE B2) 2 110 ㎒ to 2 155 ㎒ (LTE B4) 869 ㎒ to 894 ㎒ (LTE B5) 734 ㎒ to 746 ㎒ (LTE B17) 1.2 Related Submittal(s) / Grant(s) Original submittal only. FCC ID: ZNFH443 Report No.: HCT-E-1501-F008 Page: 5 of 22 F-01P-02-014 (Rev.00) HCT CO., LTD 1.3 Test Facility Test site is located at 74, SEOICHEON-RO, 578BEON-GIL, MAJANG-MYEON, ICHEON-SI, GYEONGGI-DO, SOUTH KOREA. Those measurement facilities are constructed in conformance with the requirements of ANSI C63.4-2003. Measurement Facilities Reg. No. Radiated Field strength measurement facility (3 m) 90661 (February 28, 2014) Radiated Field strength measurement facility (10 m) 90661 (February 28, 2014) FCC ID: ZNFH443 Report No.: HCT-E-1501-F008 Page: 6 of 22 F-01P-02-014 (Rev.00) HCT CO., LTD 1.4 Tested System Details All equipment descriptions used in the tested system (including inserted cards) are: Device Type Model Name Manufacturer FCC ID / DoC Connected To EUT LG-H443 LG ZNFH443 Notebook PC, Earphone USB cable EAD62786801 Ningbo Broad - EUT, Notebook PC USB cable EAD62377905 KSD - EUT, Notebook PC Earphone EAB62950102 CRESYN - EUT Notebook PC ProBook6560b HP DoC EUT, Notebook PC adapto r Notebook PC adaptor PPP009D DELTA Electronics (Jiangsu) LTD - Notebook PC Gateway MV440 Axesstel PH7MV440 Notebook PC, Adaptor Serial mouse Serial 2 button mouse Radio shack FSUGMZE3 Notebook PC Adaptor DA-60M12 Yang Ming Industrial - Gateway RJ45 cable - - - Notebook PC, Gateway Micro SD card 8 GB SanDisk - EUT FCC ID: ZNFH443 Report No.: HCT-E-1501-F008 Page: 7 of 22 F-01P-02-014 (Rev.00) HCT CO., LTD 1.5 Cable Description Product Name Port Power Cord Shielded (Y/N) I/O Cable Shielded (Y/N) Length (m) EUT Micro USB Y Y (P,D)1.0 Earphone N/A Y (D)1.2 Notebook PC RJ 45 N/A N (D)1.5 Serial (Mouse) N/A Y (D)1.8 DC in N N/A (P)1.8 Gateway DC in N N/A (P)1.8 * The marked "(D)" means the data cable and "(P)" means the power cable. 1.6 Noise Suppression Parts on Cable. (I/O Cable) Product Name Port Ferrite Bead (Y/N) Location Metal Hood (Y/N) Location EUT Micro USB N N/A Y Both End Earphone N N/A Y EUT End Notebook PC RJ 45 N N/A N N/A Serial (Mouse) N N/A Y Notebook PC End FCC ID: ZNFH443 Report No.: HCT-E-1501-F008 Page: 8 of 22 F-01P-02-014 (Rev.00) HCT CO., LTD 2. DESCRIPTION OF TEST 2.1 Measurement of Conducted Emission The test procedure was in accordance with ANSI C63.4-2003, Clause 7 a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). If the EUT is connected to the PC through USB, the AC pow…

Text truncated - open the document above for the full version.