ZNFPBSC510Bluetooth Speaker

Rev 1.0 US All rights reserved. LG Electronics Inc., 2015 Please read all information carefully prior to using the PBS-C510 in order to prevent product damage and to enjoy the best performance. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Call (800) 243-0000 for more information. Wash hands after handling. English PBS-C510 User Manual 2 ENG Description of Part NFC Bluetooth ® Play/Pause Volume Up LED Lighting Volume Down Mood LED Play Next EQ Play Previous Charging LEDCharging Port Included in the Package USB Charging Cable User ManualPBS-C510 Bluetooth Speaker NOTE: Actual product design may differ from images shown in this manual. 3 ENG How to Use Power On/Off Power On Press the top of the speaker to power on the product. Î Power Off If you press the top of the speaker while it is powered on, the power will be turned off. Î Charging 1. Connect the USB adapter and USB charging cable. 2. Open the USB cover, then plug the USB charging cable (as shown below) into the speaker’s charging port. 3. Plug the charger into an electrical outlet. Low Battery y A low battery alert will play once per minute. y If the battery is not charged, the Speaker will power off. Battery Status Alert y Press and hold the button for 2 seconds to check the battery status of the speaker. Battery Status Low (Under 80%) Medium (Above 80%) High (Fully Charged) Charging LED Indicator Red lightViolet lightBlue light 4 ENG Button Description ButtonDescriptionButton duration Play / PauseShort touch Volume UpShort touch Volume DownShort touch Display Battery StatusLong touch (2 secs) Play NextShort touch Play PreviousShort touch Equalization Mode ChangesShort touch Enter Pairing ModeLong touch (2 secs) Change the Mood LED light. Default J Always On J Off Short touch + Dual Play InquireLong touch (2 secs) + Change to Dual playLong touch (2 secs) + or + End the Dual PlayLong touch (2 secs) + Connect with TV SyncLong touch (2 secs) + + Reset the SpeakerLong touch (5 secs) Pairing 7RXVHWKHVSHDNHU\RXPXVW¿UVWSDLULWZLWK\RXUPRELOHGHYLFH Easy Pairing 1. Push the power button to the on position. The speaker will enter pairing mode. 2. When the speaker enters pairing mode, the LED light will blink twice every 2 seconds. Pairing mode is active for 10 minutes. 3. With your mobile device, scan for and select the Bluetooth speaker. 4. If prompted, enter a password to pair the devices. Manual Pairing (use when pairing with a second mobile device or re-pairing with a previously paired device) 1. Push the power button to the on position. 2. Touch and hold the h button. 3. Repeat step 2 through 4 of Easy Pairing. NFC Bluetooth connection is available through NFC. In order to use this feature, you need to activate NFC on your mobile device. (The Read/Write item should be checked on the NFC menu on your mobile device.) 1. Bring your mobile device close to the LG logo on the top of the speaker. 2. Select “Yes” from the pop-up window to pair and connect the mobile device and speaker. 3. Once connected via NFC, bringing your mobile device close to the LG logo (NFC) on the speaker will disabled the connection. NOTE: y Once the speaker and a device have been paired, the next time the speaker is powered on it will automatically try to reconnect with the last device it was paired with. y If the speaker cannot connect to a previously paired device within 20 minutes, it will automatically power off. 5 ENG Advanced Multipoint The speaker can be connected to two devices at the same time. Pairing with Two Devices 1. Pair the speaker with the Bluetooth-enabled mobile device you want to use as your secondary device (see Pairing instructions). 2. Once paired, power off the speaker. 3. Pair and connect the speaker with your other Bluetooth-enabled mobile device. This will be your primary device. NOTE: y When the speaker is connected to two mobile devices at the same time (Multipoint), the speaker will work with the primary mobile device. y If the speaker fails to connect to the primary mobile device through Easy Pairing, it will enter Pairing mode. Auto Reconnect If in range of each other when the speaker is powered on, the speaker and the primary mobile device will automatically reconnect. The secondary mobile device will need to be manually connected by selecting LG PBS-C510 from the available devices listed in the Bluetooth menu. Out of Range If the paired devices are separated by a range of 33 feet (10 meters) or more, the speaker and paired mobile device(s) will disconnect, and the speaker will alert you. If the speaker and paired mobile device do not automatically reconnect ZKHQWKH\DUHEDFNZLWKLQWKHUHTXLUHGUDQJHEULHÀ\SUHVVh on the speaker to manually reconnect. When connected to multiple devices, the paired device that is not in use will disconnect when out of range. Dual Play (Optional) You can enjoy stereo sound using two PBS-C510 products. 8VLQJWKH3DLULQJLQVWUXFWLRQVSDLU\RXUPRELOHGHYLFHZLWKWKH¿UVW speaker A. 2. Press the h button and the button of speaker B at the same time for about 2 seconds. 3. Press the h button and the button of speaker A at the same time for about 2 seconds. The LED lighting will blink once every 2 seconds. 4. The two speakers will connect in about 5 to 10 seconds, and you can begin to play music with stereo sound. NOTE: y With Dual Play, you can adjust the volume of both speakers at the same time. y To disable the Dual Play connection, press the h button and the button (or button) at the same time for about 2 seconds. y Dual Play is support on Android or IOS devices. Equalizer Mode Change PBS-C510 speakers have three types of preset Equalizer modes. %ULHÀ\WRXFKWKH(4EXWWRQRQWKHWRSRIWKHVSHDNHU:KHQ\RXSUHVV the EQ button, the EQ settings will be applied in the order as follows: EQ ModeLED Blinking Bass Boost Mode (Low-Band Boost, Default) 1 Treble Boost (High-Band Boost)2 Power Boost Mod…

Text truncated - open the document above for the full version.

LG Electronics MobileComm USA, Inc. 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States September 18, 2015 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 LETTER FOR AUTHORIZATION To whom it may concern: I, the undersigned, hereby authorize Lab Manager Hyunchae, You (or Logan, Lee) and of SGS Korea Co., Ltd. and hereafter referred to as SGS Korea, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Lab Manager Hyunchae, You (or Logan. Lee) of SGS Korea Co., Ltd. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing SGS Korea as our agent, we still recognize that we are responsible to: a)comply with the relevant provisions of the certification program; b)make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c)make claims regarding certification only in respect of the scope for which certification has been granted; d)do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e)upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; LG Electronics MobileComm USA, Inc. 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States f)use certification only to indicate the products are certified as being in conformity with specified standards; g)endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h)ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i)keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j)take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k)document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours Jongchul Lee Director, NA Regulatory & Environmental Affairs LG Electronics MobileComm USA, Inc.

LG Electronics MobileComm USA, Inc. 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States September 18, 2015 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 REQUEST FOR CONFIDENTIALITY FCC ID: ZNFPBSC510 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LG Electronics USA hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics USA temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows: CONFIDENTIAL LIST Permanent 1 Block Diagram 2 Operational Descriptions 3 Schematics Short-Term 4 External Photos 5 Internal Photos 6 Test-Setup Photos 7 User Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely Yours Jongchul Lee Director, NA Regulatory & Environmental Affairs LG Electronics MobileComm USA, Inc.

External photos of EUT Top view of EUT Bottom view of EUT Side view of EUT

LG Electronics MobileComm USA, Inc. MODEL: PBS-C510 FCC ID: ZNFPBSC510 Bottom view of EUT

Internal photos of EUT Internal view of EUT Top view of Main PCB Bottom view of Main PCB Top view of Sub PCB Bottom view of Sub PCB Top view of Key PCB Bottom view of Key PCB View of Antenna BT Antenna NFC Antenna

FCC ID : ZNFPBSC510 According to KDB 447498 D01 General RF Exposure Guidance v05, section 4.3.1 At 100㎒to 6㎓ and for test separation distances ≤ 50 ㎜, the SAR test exclusion threshold is determined according to the following [(max. power of channel, including tune-up tolerance,㎽) / (min. test separation distance,㎜)] x [√f(㎓)] ≤ 3.0 1. SAR test exclusion threshold Frequency : 2 402㎒ (min. separation distances = 5㎜) SAR test exclusion thresholds(5㎜) = 3 x 5 / (√ 2.402 ) = 9.678 ㎽ Max. tune-up tolerance(㎽) SAR Test Exclusion Thresholds(5 mm) (㎽) 69.678 Calculation value : 6 (㎽) / 5 (㎜) x √ 2.402 = 1.860 So, Calculation value ≤ 3.0 Remark: -Max. conducted power (㎽) : maximum tolerance power of EUT (7.5㏈m) -Max. conducted power 5.6 (㎽) is closet 6 (㎽), so 6 (㎽)was calculated. 2. Conclusion : No SAR is required.

Report Number :F690501/RF-RTL009132-1Page:2of66 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory)4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2)Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) INDEX Table of ContentsPage 1. General Information ---------------------------------------------------------------------------------3 2. Transmitter Radiated Spurious Emissions and Conducted Spurious Emission ------8 3. 20㏈Bandwidth ------------------------------------------------------------------------------------ 32 4. Maximum Peak Output power --------------------------------------------------------------------39 5. Carrier Frequency Separation --------------------------------------------------------------------41 6. Number of Hopping Frequencies ----------------------------------------------------------------44 7. Time of Occupancy(Dwell Time) -----------------------------------------------------------------48 8. Transmitter AC Power Line Conducted Emission -------------------------------------------61 9. Antenna Requirement ------------------------------------------------------------------------------66 Report Number :F690501/RF-RTL009132-1Page:3of66 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory)4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2)Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 1. General Information 1.1. Testing Laboratory SGS Korea Co., Ltd. (Gunpo Laboratory) -Wireless Div. 2FL, 10-2, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 15807 All SGS services are rendered in accordance with the applicable SGS conditions of service available on request and accessible athttp://www.sgs.com/en/Terms-and-Conditions.aspx. Phone No. :+ 82 31 688 0901 Fax No. :+ 82 31 688 0921 1.2. Details of Applicant Applicant:LG Electronics MobileComm USA, Inc. Address:1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States Contact Person:Lee, Jong-Chul Phone No.:+1 201 816 2003 1.3. Description of EUT Kind of Product Bluetooth Speaker Model Name PBS-C510 Variant Model Name NP7860W, NP7860U, NP7860P, NP7860B, NA8860W, NA8860U, NA8860P Power Supply DC 3.7 V (Used Li-ion Battery) Frequency Range 2 402㎒~ 2 480㎒(BT) Modulation Technique GFSK, π/4DQPSK, 8DPSK Number of Channels 79 channels (BT) Antenna Type Internal type Antenna Gain 0.66㏈i 1.4. Declaration by the manufacturer - Adaptive Frequency Hopping is supported and use at least 20 channels. Report Number :F690501/RF-RTL009132-1Page:4of66 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory)4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2)Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 1.5. Information about the FHSS characteristics: 1.5.1. Pseudorandom Frequency Hopping Sequence The channel is represented by a pseudo-random hopping sequence hopping through the 79 RF channels. The hopping sequence is unique for the piconet and is determined by the Bluetooth device address of the master; the phase in the hopping sequence is determined by the Bluetooth clock of the master. The channel is divided into time slots where each slot corresponds to an RF hop frequency. Consecutive hops correspond to different RF hop frequencies. The nominal hop rate is 1 600 hops/s. 1.5.2. Equal Hopping Frequency Use The channels of this system will be used equally over the long-term distribution of the hopsets. 1.5.3. Example of a 79 hopping sequence in data mode: 02, 05, 31, 24, 20, 10, 43, 36, 30, 23, 40, 06, 21, 50, 44, 09, 71, 78, 01, 13, 73, 07, 70, 72, 35, 62, 42, 11, 41, 08, 16, 29, 60, 15, 34, 61, 58, 04, 67, 12, 22, 53, 57, 18, 27, 76, 39, 32, 17, 77, 52, 33, 56, 46, 37, 47, 64, 49, 45, 38, 69, 14, 51, 26, 79, 19, 28, 65, 75, 54, 48, 03, 25, 66, 05, 16, 68, 74, 59, 63, 55 1.5.4. System Receiver Input Bandwidth Each channel bandwidth is 1㎒. The system receivers have input bandwidths that match the hopping channel bandwidths of their corresponding transmitters and shift frequencies in synchronization with the transmitted signals. 1.5.5. Equipment Description 15.247(a)(1) that the rx input bandwidths shift frequencies in synchronization with the transmitted signals. 15.247(g): In accordance with the Bluetooth Industry Standard, the system is designed to comply with all of the regulations in Section 15.247 when the transmitter is presented with a continuous data (or information) system. 15.247(h): In accordance with the Bluetooth Industry Standard, the system does not coordinate it channels selection/ hopping sequence with other frequency hopping systems for the express purpose of avoiding the simultaneous occupancy of individual hopping frequencies by multiple transmitters. Report Number :F690501/RF-RTL009132-1Page:5of66 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory)4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2)Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 1.6. Information of variant model Model nameInformation PBS-C510- Basic model NP7860W - Same to basic model, but it is different below function. - CAV model : White c…

Text truncated - open the document above for the full version.

Test setup photos of EUT 1. Orthogonal planes of EUT - The testing was set in the two orthogonal planes and measured for each position (X, Y). A. X- axis B. Y-axis 2. Worst case of orthogonal planes each frequency band - Test setup photos for each mode were reported as representative worst axis after radiated measurements for each position were complete. A. Photo of Radiated Spurious Emission Test (Below 1㎓) B. Photo of Radiated Spurious Emission Test (Above 1㎓) 3. Photos of AC Power line emission test