ZO4M1S-ROBSTEPRobstep

1 ¦ Thank you for your purchasing Robstep. ¦ Robstep is an intelligent robot that balances automatically. ¦ This User’s Manual providing you information about how to assemble and safely use the Robstep, and how to maintain it . If you want to get the most pleasure out of your Robstep , please read it carefully. ¦ It is critical that you know of all safety notices and precautions before your first ride. This User’s manual applies on all smart balanced robots named Robstep which are produced by Robstep 2 3 3. Assembly Instruction In this part, we will talk about the parts of Robstep and how to install Robstep. 3.1 Double check the spare parts inside the packing Please check the package of Robstep and make sure that all spare parts are complete. The spare parts of Robstep are listed as follows, if any of them missing, please contact with the local agent or us directly. 1) Main body 2) Handlebar grip 3) Handlebar stem 4) Charger 5) Tool and screws bag (which contains of erecting tools and 10 screws) 6) User’s Manual, and warranty card 7) Product quality certificate 3.2 Installing Robstep Step one: Insert the rubber of handlebar into the handlebar according to the instruction of the following pictures, tighten up the four screws with tools (screws and tools are all given, please pay attention to the anterio‐posterior of the rubber of the handlebar, and install it according to the instruction by the arrows with same color). This part is handlebar components and it can be quick‐released by the locking wrench. Step two: Under the loosened state of the locking wrench, please insert the handlebar components onto the rotary joint of Robstep. Then tighten the locking wrench by your hand, when the handlebar components insert the bottom. Make sure the stability of the handlebar components before you ride the Robin. You can gently try to lift up the handlebar when the Robin is power off, if the handlebar is loosened, you should tighten the two screws of the locking wrench. (If it need to disassemble ,please hold handlebar first, then release the Quick‐release part. 4 Step three: Press thepower on button at rear side to use Robstep. 4. Controlling of Robstep and the display board 4.1 Pedal sensor There are four sensors under the pedal, any of them stepped upon by users, Robstep will enter into the balance model automatically. 4.2 Display board The display board of Robstep is fixed on the top of the battery. It shows information about Robstep during riding. 5 5. Instructions of battery of Robstep 6 7 8 9 7. How to use Robstep You need to note some related safety matters before driving Robstep. It is very important for you to understand all safety matters mentioned inside the user’s manual. 7.1 Start Robstep ¦ If it is your first time to start Robstep, please press the button on the back cover of Robstep Body. 7.2 Safe Parking ¦ When there is an incorrect operation or the power consumption reaches the minimum quantity within normal driving, the system will then generate a secure parking information, meanwhile Robstep will have a high-frequency vibration, then Robstep can automatically slow to a stop. 10 11 12 13 14 15 16 17 18 19

Confidentiality Request Letter Page 1 of 1 December 20, 2012 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Permanent Confidentiality Request Confidentiality Request regarding application for certification of FCC ID: ZO4M1S-ROBSTEP We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Operational Description - Schematic The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature: Client’s name / title: Gaihua Guo/Manager Contact information / address: Tech-Road.9-1, High-tech industrial park, DongGuan, China TEL: 0769-2662 0928 FAX: 0769-2662 0929 E-mail: [email protected]

External Photo

FCC Certification Label FCC ID: ZO4M1S-ROBSTEP This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.This device may not cause harmful interference, and 2.This device must accept any interference received, including interference that may cause undesired operation. Label Location on EUT EUT View/ FCC ID Label Location

Internal Photo BT Antenna

FCC PART 15.249 EMI MEASUREMENT AND TEST REPORT For Robstep Robot Co.,Ltd. DongGuan Tech-Road.9-1, High-tech industrial park, Songshan Lake, DongGuan, China FCC ID: ZO4M1S-ROBSTEP December 19, 2012 This Report Concerns: Original Report Equipment Type: Robstep Test Engineer: Anna Lv Test Engineer of performing the tests: Adam Yang Report No.: BST12111020Y-1E-3 Receive EUT Date/Test Date: December 11, 2012 / December 12-18, 2012 Reviewed By: Mike Moo Prepared By: Shenzhen BST Technology Co.,Ltd. 3F,Weames Technology Building, No. 10 Kefa Road, Science Park, Nanshan District,Shenzhen,Guangdong,China Tel: 0755-26747751-3 Fax: 0755-26747751-3 ext.826 Note: The test report is specially limited to the above company and this particular sample only. It may not be duplicated without prior written consent of Shenzhen BST Technology Co.,Ltd. This report must not be used by the client to claim product certification,approval,or endorsement by NVLAP, NIST or any agency of the US Government. FCC ID: ZO4M1S-ROBSTEP BST12111020Y-1E-3 Page 2/24 TABLE OF CONTENTS 1. GENERAL INFORMATION ....................................................................................................3 1.1. Report information ............................................................................................................3 1.2. Measurement Uncertainty .................................................................................................3 2. PRODUCT DESCRIPTION ......................................................................................................4 2.1. EUT Description ...............................................................................................................4 2.2. Block Diagram of EUT Configuration..............................................................................5 2.3. Support Equipment List ....................................................................................................5 2.4. Test Conditions .................................................................................................................5 3. TEST RESULTS SUMMARY ...................................................................................................6 Modifications ................................................................................................................................6 4. TEST EQUIPMENT USED .......................................................................................................7 5. ANTENNA REQUIREMENT ...................................................................................................8 5.1. Standard Applicable..........................................................................................................8 5.2. Antenna Connected Construction .....................................................................................8 5.3. Result ................................................................................................................................8 6. CONDUCTED POWER LINE TEST .......................................................................................9 6.1. Test Equipment .................................................................................................................9 6.2. Test Procedure ..................................................................................................................9 6.3. Test Setup..........................................................................................................................9 6.4. Conducted Power line Emission Limits............................................................................9 6.5. Conducted Power Line Test Result.................................................................................10 7. RADIATED EMISSION TEST ...............................................................................................12 7.1. Test Equipment ...............................................................................................................12 7.2. Test Procedure ................................................................................................................12 7.3. Radiated Test Setup ........................................................................................................12 7.4. Radiated Emission Limit.................................................................................................14 7.5. Radiated Emission Test Result .......................................................................................15 8. BAND EDGE .............................................................................................................................20 8.1. Test Equipment ...............................................................................................................20 8.2. Test Procedure ................................................................................................................20 8.3. Band Edge FCC 15.249(d) Limit ....................................................................................20 8.4. Band Edge Test Result ....................................................................................................21 FCC ID: ZO4M1S-ROBSTEP BST12111020Y-1E-3 Page 3/24 1. GENERAL INFORMATION 1.1. Report information 1.1.1.This report is not a certificate of quality; it only applies to the sample of the specific product/equipment given at the time of its testing. The results are not used to indicate or imply that they are application to the similar items. In addition, such results must not be used to indicate or imply that BST approves recommends or endorses the manufacture, supplier or use of such product/equipment, or that BST in any way guarantees the later performance of the product/equipment. 1.1.2.The sample/s mentioned in this report is/are supplied by Applicant, BST therefore assumes no responsibility for the accuracy of information on the brand name, model number, origin of manu…

Text truncated - open the document above for the full version.

Radiated emissions test Conducted emissions test