2A2AI-R15Thermal transfer label printer

FCC Caution. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Rev 1/26/2023 Shenzhen Yinxiaoqian technology Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2026-05-15 FCC ID: 2A2AI-R15 Ref. #1: Attestation Statements Part 2.911(d)(5)(i) Filing Shenzhen Yinxiaoqian technology Co., Ltd. certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Shenzhen Yinxiaoqian technology Co., Ltd. certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Ref. #2: Attestation Statements Part 2.911(d)(5)(ii) Filing Shenzhen Yinxiaoqian technology Co., Ltd. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Applicant: Shenzhen Yinxiaoqian technology Co., Ltd. Address: 202E, building A4, Hom Industrial Zone, 41 Wuhe Avenue (South) Nankeng community, Bantian street, Longgang District, Shenzhen. China Contact Person: Musk Zhang Tel.: 15815526007 Email: [email protected] Sincerely, Rev 1/26/2023 Signature:

Attestation Statements Date: 2026-05-15 TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046, USA RE: Attestation Statements Part 2.911(d)(7) request for(FCC ID: 2A2AI-R15) Shenzhen Yinxiaoqian technology Co., Ltd., the undersigned, hereby authorize HOPEK CORPORATION INC to act as our designated agent for service of process, Shenzhen Yinxiaoqian technology Co., Ltd. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission- related proceeding involving the equipment. HOPEK CORPORATION INC accepts the responsibility to act as designated agent for service of process. Applicant Information： Company name: Shenzhen Yinxiaoqian technology Co., Ltd. Contact Name: Musk Zhang Address: 202E, building A4, Hom Industrial Zone, 41 Wuhe Avenue (South) Nankeng community, Bantian street, Longgang District, Shenzhen. China Telephone No: 15815526007 Email: [email protected] FRN: 0031025356 Signature: Musk Zhang Agent Information: Company Name:HOPEK CORPORATION INC Address:16755 Coyote Bush Dr Unit 84, San Diego, CA 92127 United States FRN: 0034562900 Contact Name: YangyangXu Telephone No:561-875-9826 Email: [email protected] Signature: Yangyang Xu

Shenzhen Yinxiaoqian technology Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: May 19, 2026 Subject; Request for Confidentiality FCC ID: 2A2AI-R15 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure SOFTWARE SECURITY REQUIREMENTS FOR U-NII DEVICES In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Musk Zhang Title: Manager

Effective Date: April 2, 2020 QSF 7.6.4-8 – Agent Authorization Letter Template Page 1 of 1 Revision Date: Revision: 0 Shenzhen Yinxiaoqian technology Co., Ltd. Date：2026-05-15 Product Model Number: R15, R15pro, R15C, R15D, R15S, R15Z FCC ID：2A2AI-R15 To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following: • Testing • Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. Signature: By: Musk Zhang Contact Listed on FCC Wesbite Title: Manager Email: [email protected] On behalf of: Shenzhen Yinxiaoqian technology Co., Ltd.

Shenzhen Yinxiaoqian technology Co., Ltd. Declaration Letter of Model Difference Date: 2026-05-15 FCC ID: 2A2AI-R15 Tested Model Number: R15 Adding Model Number(s): R15pro, R15C, R15D, R15S, R15Z All above models are identical in the same PCB layout, interior structure and electrical circuits, The difference is power. Yours Sincerely, Applicant: Shenzhen Yinxiaoqian technology Co., Ltd. Address: 202E, building A4, Hom Industrial Zone, 41 Wuhe Avenue (South) Nankeng community, Bantian street, Longgang District, Shenzhen. China Contact Person: Musk Zhang Tel.: 15815526007 Email: [email protected] Sincerely, Signature:

Page 1 of 6 Report No.: LGT26D135 Appendix - External Photographs of EUT Constructional Details Photo 1 Photo 2 Page 2 of 6 Report No.: LGT26D135 Appendix - External Photographs of EUT Constructional Details Photo 3 Photo 4 Page 3 of 6 Report No.: LGT26D135 Appendix - External Photographs of EUT Constructional Details Photo 5 Photo 6 Page 4 of 6 Report No.: LGT26D135 Appendix - External Photographs of EUT Constructional Details Photo 7 Photo 8 Page 5 of 6 Report No.: LGT26D135 Appendix - External Photographs of EUT Constructional Details Photo 9 Photo 10 Page 6 of 6 Report No.: LGT26D135 Appendix - External Photographs of EUT Constructional Details Photo 11 Photo 12

Label Size:32*56mm FCC ID: 2A2AI-R15

Page 1 of 4 Report No.: LGT26D135 Appendix - Internal Photographs of EUT Constructional Details Photo 1 Photo 2 Page 2 of 4 Report No.: LGT26D135 Appendix - Internal Photographs of EUT Constructional Details Photo 3 Photo 4 BT ANT NFC ANT not usable Page 3 of 4 Report No.: LGT26D135 Appendix - Internal Photographs of EUT Constructional Details Photo 5 Photo 6 Page 4 of 4 Report No.: LGT26D135 Appendix - Internal Photographs of EUT Constructional Details Photo 7

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Page 1 of 8 EMF TEST REPORT Product Name: Thermal transfer label printer Model Number: R15, R15pro, R15C, R15D, R15S, R15Z FCC ID: 2A2AI-R15 Issued For : Shenzhen Yinxiaoqian technology Co., Ltd. 202E, building A4, Hom Industrial Zone, 41 Wuhe Avenue (South) Nankeng community, Bantian street, Longgang District, Shenzhen. China Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Report Number: LGT26D135HA01 Sample Received Date: April 22, 2026 Date of Test: April 22, 2026 ~ May 06, 2026 Date of Issue: May 06, 2026 Report No.: LGT26D135HA01 Page 2 of 8 TEST REPORT CERTIFICATION Applicant: Shenzhen Yinxiaoqian technology Co., Ltd. Address: 202E, building A4, Hom Industrial Zone, 41 Wuhe Avenue (South) Nankeng community, Bantian street, Longgang District, Shenzhen. China Manufacturer: Shenzhen Yinxiaoqian technology Co., Ltd. Address: 202E, building A4, Hom Industrial Zone, 41 Wuhe Avenue (South) Nankeng community, Bantian street, Longgang District, Shenzhen. China Product Name: Thermal transfer label printer Trademark: MARKLIFE Model Number: R15, R15pro, R15C, R15D, R15S, R15Z Sample Status: Normal APPLICABLE STANDARDS STANDARD TEST RESULTS FCC 47 CFR §2.1093 KDB 447498 D01 General RF Exposure Guidance v06 PASS Prepared by: Approved by: Chris Chen Vita Li Engineer Technical Director Report No.: LGT26D135HA01 Page 3 of 8 TABLE OF CONTENTS 1 . GENERAL INFORMATION 5 1.1 GENERAL DESCRIPTION OF THE EUT 5 1.2 TEST LABORATORY 5 2 . FCC 47CFR §2.1093 REQUIREMENT 6 2.1 TEST STANDARDS 6 2.2 LIMIT 6 2.3 TEST RESULT 8 Report No.: LGT26D135HA01 Page 4 of 8 Revision History Rev. Issue Date Revisions 00 May 06, 2026 Initial Issue Report No.: LGT26D135HA01 Page 5 of 8 1. GENERAL INFORMATION 1.1 GENERAL DESCRIPTION OF THE EUT Product Name: Thermal transfer label printer Test Model Number: R15 Series Number: R15pro, R15C, R15D, R15S, R15Z Model Difference: All above models are identical in the same PCB layout, interior structure and electrical circuits, The difference is power. Frequency Bands: Bluetooth 2402-2480MHz Rating: Input: DC 5V 2A Battery: Capacity: 1300mAh Rated Voltage: 3.7V Hardware Version: V1.0 Software Version: V1.0.0 1.2 TEST LABORATORY Company Name: Shenzhen LGT Test Service Co., Ltd. Address: Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Accreditation Certificate: FCC Registration No.: 746540 CAB ID: CN0136 Report No.: LGT26D135HA01 Page 6 of 8 2. FCC 47CFR §2.1093 REQUIREMENT 2.1 TEST STANDARDS The limit for Maximum Permissible Exposure (MPE) specified in KDB 447498 D01 General RF Exposure Guidance v06 is followed. The gain of the antennas used in the product is extracted from the Antenna data sheets provided and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis Transmission formula is far field assumption, the calculated result of that is an over-prediction for near field power density. It is taken as worst case to specify the safety range. 2.2 LIMIT Approximate SAR Test Exclusion Power Thresholds at Selected Frequencies and Test Separation Distances are illustrated in the following Table. Report No.: LGT26D135HA01 Page 7 of 8 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] • [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,where f(GHz) is the RF channel transmit frequency in GHz. Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. Report No.: LGT26D135HA01 Page 8 of 8 2.3 TEST RESULT Turn up Result Mode Turn up Power BT-GFSK 7±1dBm BLE 1M-GFSK 2.5±1.5dBm The MPE result of worst mode: RF Function Frequency (MHz) Max Turn up Power (dBm) Max Turn up Power (mW) Estimated SAR Limit Ratio Result BT 2480 8.00 6.31 1.987 3 0.662 Pass BLE 2440 4.00 2.51 0.785 3 0.262 Pass Note: 1. The Maximum Power Density is less than the limit, complies with the exemption requirements. ※※※※※END OF THE REPORT※※※※※

BluetoothAntenna specification YichipMicroelectronics ©2014 Antenna Type: PCB Antenna Manufacturer: Shenzhen Yinxiaoqian technology Co., Ltd. Address: 202E, building A4, Hom Industrial Zone, 41 Wuhe Avenue (South) Nankeng community, Bantian street, Longgang District, Shenzhen. China ANT5: GianandEfficiency Frequency (MHz) Efficiency(%)Gain(dBi) 230034.81-0.14 232038.900.50 234038.951.16 236040.111.28 238039.281.80 240041.772.20 242049.712.34 244050.232.58 246045.912.45 248042.462.09 250041.102.01 252035.580.96 254032.430.44 3Dand1DRadiationPatterns Total P o w e r ( d B m ) -15 10 -10 -5 0 5 X Y Z Azimuth = 0.0 Elevation = 0.0 Roll = 0.0 Cut1 P o w e r ( d B m ) Angle (? Scale: 1/div Min: -5 Max: 5 0 180 30 210 60 240 90270 120 300 150 330 Cut2 P o w e r ( d B m ) Angle (? Scale: 2/div Min: -16 Max: 4 0 180 30 210 60 240 90270 120 300 150 330 Cut3 P o w e r ( d B m ) Angle (? Scale: 2/div Min: -6 Max: 6 0 180 30 210 60 240 90270 120 300 150 330 ANT1-ANT85dbmTRPtestresult： Band ANTFrequency Result (dBm) Note BT ANT12440 -6.501 ANT22440 -0.582 ANT32440 -2.913 ANT42440 0.924 ANT52440 0.095 ANT62440 0.346 ANT72440 0.147 ANT82440 -2.148

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Page 1 of 47 RF TEST REPORT Product Name: Thermal transfer label printer Model Number: R15, R15pro, R15C, R15D, R15S, R15Z FCC ID: 2A2AI-R15 Issued For : Shenzhen Yinxiaoqian technology Co., Ltd. 202E, building A4, Hom Industrial Zone, 41 Wuhe Avenue (South) Nankeng community, Bantian street, Longgang District, Shenzhen. China Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Report Number: LGT26D135RF02 Sample Received Date: April 22, 2026 Date of Test: April 22, 2026 ~ May 06, 2026 Date of Issue: May 06, 2026 Report No.: LGT26D135RF02 Page 2 of 47 TEST REPORT CERTIFICATION Applicant: Shenzhen Yinxiaoqian technology Co., Ltd. Address: 202E, building A4, Hom Industrial Zone, 41 Wuhe Avenue (South) Nankeng community, Bantian street, Longgang District, Shenzhen. China Manufacturer: Shenzhen Yinxiaoqian technology Co., Ltd. Address: 202E, building A4, Hom Industrial Zone, 41 Wuhe Avenue (South) Nankeng community, Bantian street, Longgang District, Shenzhen. China Product Name: Thermal transfer label printer Trademark: MARKLIFE Model Number: R15, R15pro, R15C, R15D, R15S, R15Z Sample Status: Normal APPLICABLE STANDARDS STANDARD TEST RESULTS FCC Part 15.247, Subpart C ANSI C63.10-2020 PASS Prepared by: Approved by: Chris Chen Vita Li Engineer Technical Director Report No.: LGT26D135RF02 Page 3 of 47 Table of Contents Page 1. SUMMARY OF TEST RESULTS 6 1.1 TEST LABORATORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 9 2.3 TEST SOFTWARE AND POWER LEVEL 9 2.4 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 10 2.5 EQUIPMENTS LIST 11 3. EMC EMISSION TEST 13 3.1 CONDUCTED EMISSION MEASUREMENT 13 3.2 TEST PROCEDURE 14 3.3 TEST SETUP 14 3.4 EUT OPERATING CONDITIONS 14 3.5 TEST RESULTS 15 4. RADIATED EMISSION MEASUREMENT 17 4.1 RADIATED EMISSION LIMITS 17 4.2 TEST PROCEDURE 19 4.3 TEST SETUP 19 4.4 EUT OPERATING CONDITIONS 20 4.5 FIELD STRENGTH CALCULATION 20 4.6 TEST RESULTS (BAND EDGE REQUIREMENTS) 25 5. CONDUCTED SPURIOUS & BAND EDGE EMISSION 26 5.1 LIMIT 26 5.2 TEST PROCEDURE 26 5.3 TEST SETUP 26 5.4 EUT OPERATION CONDITIONS 26 5.5 TEST RESULTS 26 6. POWER SPECTRAL DENSITY TEST 27 6.1 LIMIT 27 6.2 TEST PROCEDURE 27 6.3 TEST SETUP 27 6.4 EUT OPERATION CONDITIONS 27 Report No.: LGT26D135RF02 Page 4 of 47 6.5 TEST RESULTS 27 7. BANDWIDTH TEST 28 7.1 LIMIT 28 7.2 TEST PROCEDURE 28 7.3 TEST SETUP 28 7.4 EUT OPERATION CONDITIONS 28 7.5 TEST RESULTS 28 8. PEAK OUTPUT POWER TEST 29 8.1 LIMIT 29 8.2 TEST PROCEDURE 29 8.3 TEST SETUP 29 8.4 EUT OPERATION CONDITIONS 29 8.5 TEST RESULTS 29 9. ANTENNA REQUIREMENT 30 9.1 STANDARD REQUIREMENT 30 9.2 EUT ANTENNA 30 APPENDIX I - TEST RESULTS 31 DUTY CYCLE 31 MAXIMUM PEAK CONDUCTED OUTPUT POWER 33 -6DB BANDWIDTH 35 OCCUPIED CHANNEL BANDWIDTH 37 MAXIMUM POWER SPECTRAL DENSITY LEVEL 39 BAND EDGE 41 CONDUCTED RF SPURIOUS EMISSION 44 APPENDIX II - MEASUREMENT PHOTOS 47 Report No.: LGT26D135RF02 Page 5 of 47 Revision History Rev. Issue Date Revisions 00 May 06, 2026 Initial Issue Report No.: LGT26D135RF02 Page 6 of 47 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: KDB 558074 D01 Part 15.247 Meas Guidance v05r02. FCC Part 15.247, Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS -- 15.247 (a)(2) 6dB Bandwidth PASS -- 15.247 (b)(3) Output Power PASS -- 15.209 Radiated Spurious Emission PASS -- 15.247 (d) Conducted Spurious & Band Edge Emission PASS -- 15.247 (e) Power Spectral Density PASS -- 15.205 Restricted Band Edge Emission PASS -- Part 15.247(d)/ Part 15.209(a) Band Edge Emission PASS -- 15.203 Antenna Requirement PASS -- NOTE: (1) ‘N/A’ denotes test is not applicable in this Test Report. (2) All tests are according to ANSI C63.10-2020. Report No.: LGT26D135RF02 Page 7 of 47 1.1 TEST LABORATORY Company Name: Shenzhen LGT Test Service Co., Ltd. Address: Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Accreditation Certificate: FCC Registration No.: 746540 CAB ID: CN0136 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 Occupied Channel Bandwidth ±0.46% 2 RF Output Power, Conducted ±0.71dB 3 Power Spectral Density, Conducted ±1.57dB 4 Unwanted Emission, Conducted ±0.63dB 5 Conducted emission ±2.80dB 6 All Emissions, Radiated (0.009-30MHz) ±2.16dB 7 All Emissions, Radiated (30MHz-1GHz) ±4.61dB 8 All Emissions, Radiated (1GHz-18GHz) ±5.49dB 9 Temperature ±0.5°C 10 Humidity ±2% 11 Duty Cycle ±2.3% Note: The measurement uncertainty is not included in the test result. Report No.: LGT26D135RF02 Page 8 of 47 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name: Thermal transfer label printer Test Model Number: R15 Series Number: R15pro, R15C, R15D, R15S, R15Z Model Difference: All above models are identical in the same PCB layout, interior structure and electrical circuits, The difference is power. Product Description: Operation Frequency: 2402~2480 MHz Modulation Type: GFSK Radio Technology: BLE Bluetooth Configuration: BLE (1M PHY) Number Of Channel: 40 Antenna Design…

Text truncated - open the document above for the full version.

Page 1 of 2 Report No.: LGT26D135 Appendix - Test Setup photos Set-up for Radiated Spurious Emission, Below 1GHz Set-up for Radiated Spurious Emission, Above 1GHz Page 2 of 2 Report No.: LGT26D135 Set-up for Conducted Emission