2A2H2-BDRV1BDRV1

INSTRUCTION MANUAL Robot Vacuum with Mapping Technology Please read before returning this product for any reason. BDRV1 TABLE OF CONTENTS Safety1 - 2 Setting Up The Roboseries9 Dustbin Overview5 Main Brush Maintenance12 Maintaining the Dustbin and Filters13 In The Box3 Robot Indicators6 Using the Black + Decker Home App10 Side Brush and Sensor Maintenance14 Product Overview4 Setting up the Charging Dock7 - 8 Using Your Roboseries and Remote11 Roboseries Troubleshoot15 Warranty16 1 SAFETY SAFETY DEFINITIONS WARNING: Indicates a hazardous situation that, if not avoided, could result in death or serious injury. CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury. NOTICE: Indicates a hazardous situation that, if not avoided, could result in property damage. Before using this product, please read the following safety instructions and follow all safety precautions. Any operation inconsistent with this instruction manual may cause damage to this product. • Your robot is not a toy. Small children and pets should be supervised when your robot is operating. • Do not sit or stand on your robot. • Do not use unauthorized chargers. Use of an unauthorized charger could cause the battery to generate heat, smoke, catch fire or explode. Contact customer service for a replacement charger. • Do not open your robot except as instructed to maintain the dustbin and filter(s). Do not open the charging dock as there are no user serviceable parts inside. • Risk of electric shock. Only use indoors and in dry locations. • Do not handle your robot with wet hands. • Store and operate your robot in room temperature environments only. • Do not operate the robot in areas with exposed electrical outlets in the floor. • Do not attempt to open, crush or heat the battery of your robot above 175 ̊F. • Do not subject the battery to mechanical shock. • Do not operate the vacuum without the dustbin installed. • Do not short circuit the battery of your robot by allowing any metal objects to contact the battery terminal. • Do not immerse the battery in liquid. • Do not attempt to charge damaged or leaking battery packs. If battery leakage occurs, thoroughly wash any affected skin, making sure to keep battery acid away from eyes, ears, nose and mouth. Immediately wash any clothing or other surface that comes in contact with leaked battery acid. If a chemical burn occurs or if irritation persists, seek medical attention.Dispose according to Local, State or Federal regulations. • If the robot passes over a power cord there is a chance an object can be pulled off a table. Before using the robot, clear the floor of objects such as clothing, cords for blinds, curtains, power cords and any fragile objects which can be easily damaged. • Do not use the robot to pick up sharp objects, or anything that is burning or smoking. WARNING: CAUTION: 2 SAFETY • Battery acid leakage can cause personal injury and cause damage to the product and surrounding property. If battery leakage occurs, thoroughly wash any affected skin, making sure to keep battery acid away from eyes, ears, nose and mouth. Immediately wash any clothing or other surface that comes in contact with leaked battery acid. If a chemical burn occurs or if irritation persists, seek medical attention.Dispose according to Local, State or Federal regulations. • Batteries are to be inserted following the polarity markings on the product. • NEVER mix old and new batteries or different brands of batteries. Replace all batteries at the same time • NEVER mix alkaline, standard (carbon-zinc), rechargeable (nickel cadmium) batteries with this product • NEVER dispose of batteries in fire, as they may leak and explode. • Promptly remove exhausted batteries from product. • Remove batteries before extended storage. WARNING: ALKALINE BATTERY WARNING (AAA Battery for Remote Control Only) • This robot is intended for dry floor use only. Do not use the robot to pick up any wet spills and do not allow the dustbin contents to become wet. • Do not place anything on top of your robot • Regularly wipe charge contacts on your robot and charge dock. Failure to maintain charge contacts could impact the robots ability to properly charge. • Product may not be used with any type of power converter. Use of power converters will void the warranty. • The battery pack must be removed from the robot before recycling or disposal. • Do not use non-rechargeable batteries in your robot. For battery replacement contact customer care. • Before long term storage of your robot, fully charge and remove the battery. NOTICE: BDRV1-ST-IB-V1 3 IN THE BOX 1: Charging Dock 2: Roboseries Vacuum BDRV1 3: Charging Adapter 4: Sidebrush 5: Remote 1 5 3 2 4 4 PRODUCT OVERVIEW FRONT BACK BOTTOM 3 1 4 5 6 7 2 CHARGING BASE 1: Power Button 2: WiFi Indicator 3: Home Button 4: Charging Contacts 5: Navigation Sensors 6: Dustbin Release Latch 7: Dustbin 8: Charging Contacts 9: Side Brush 10: Omnidirectional Wheel 11: Detection Sensors 12: Left Wheel 13: Right Wheel 14: Main Brush 8 11 13 9 12 14 10 1: Bin/Filter Release Latch 2: HEPA Filter 3: Screen Filter (Non removable) 1 3 2 5 DUSTBIN OVERVIEW 1 3 2 1 4 3 2 • Hold to turn on/off • Press to start/pause cleaning • Blinking White: Standby Mode • Solid White (OFF Charge Base): Cleaning • Solid White (ON Charge Base): Fully Charged • Breathing White: Charging • Amber: Error • Lights off: Off/sleeping • Press to return to charging dock for recharging POWER BUTTONPOWER/HOME LED STATES WIFI INDICATOR STATES CHARGING INDICATOR LED STATES HOME BUTTON CHARGING INDICATOR WIFI INDICATOR • Blinking White: Network Configuration Mode • Solid White: Wifi connected • Light Off: Wifi disconnected / Network configuration failure • Will remain lit Blue when connected to power 4 6 ROBOT INDICATORS SETTING UP YOUR ROBOSERIES The following pages outline the complete setup process. For your convenience we created a step-by-step video to help guide you through setup…

Text truncated - open the document above for the full version.

Silver Point Innovations LLC NY Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2023-11-22 FCC ID:2A2H2-BDRV1 Ref. #1: Attestation Statements Part 2.911(d)(5)(i) Filing Silver Point Innovations LLC NY certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Ref. #2: Attestation Statements Part 2.911(d)(5)(ii) Filing Silver Point Innovations LLC NY certifies that, as of the date of the filing of the application, the applicant is notidentified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates)as an entity producing “covered” equipment. Applicant: Silver Point Innovations LLC NY Address: 261 5th avenue Suite 1512 New York NY 10016 Contact Person: Sean Chraime Tel: +1-917-669-1210 Email: [email protected] Sincerely, Signature:

CFR 47 §2.911(d)(7) U.S Agent U.S. AGENT LETTER OF ATTESTATION Date: 2023-11-22 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: 2A2H2-BDRV1 Silver Point Innovations LLC NY (“the Applicant”) certifies that, as of the date of the filing of the application, Silver Point Innovations LLC NY (U.S. agent). is our designated U.S. agent for service of process for the above referenced FCC ID. Silver Point Innovations LLC NY (“the Applicant”)accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Silver Point Innovations LLC NY (U.S. agent) accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: Silver Point Innovations LLC NY Address: 261 5th avenue Suite 1512 New York NY 10016 FRN: 0031104359 Tel.: +1-917-669-1210 Email: [email protected] Signed by (printed name): Sean Chraime Signature:

AntennaSpecification Manufacture：TUYA ProductName：WBR3Antenna AntennaType：PCB TestDate：2019.05.20 Testedby：LongWang Approvedby：Licco Content 1.GeneralDescription.................................................................................1 2.TestConfigurations...................................................................................2 2.1TestEnvironment............................................................................2 2.2TestEquipment...............................................................................2 2.3TestPrinciple...................................................................................2 3.TestResults..............................................................................................3 3.1GainandEfficiency..........................................................................3 3.2RadiationPattern............................................................................4 4.AntennaDimensions................................................................................6 5.EUTPhoto................................................................................................6 6.TestSetupPhoto......................................................................................7 1 1.GeneralDescription ManufacturerHangzhouTuyaInformationTechnologyCo.,Ltd Address Room701,Building3,MoreCenter,No.87GuDunRoad, Hangzhou,Zhejiang,China TestLocation Room106,Building3,LetongSciencePark,No.500, QiuyiRoad,BinjiangDistrict,Hangzhou ProductNameWBR3Antenna Productmodel WBR3 AntennaType PCBAntenna TestItems Gain;Efficiency;RadiationPattern TestFrequency 2400-2500MHz TestStandard ANSI/IEEEStd149-1979 2 2.TestConfigurations 2.1TestEnvironment Temperature(°C)25 Humidity(%RH)60 AtmosphericPressure(kPa)100.5 2.2TestEquipment TestSystemTEM24Multi-probeMicrowaveChamber TestInstrumentAgilentE5071B 2.3TestPrinciple 3 3.TestResults 3.1GainandEfficiency Frequency(MHz)PeakGain(dBi)Efficiency(%) 2400 1.6252.29 2410 1.7152.17 2420 1.9353.14 2430 1.9854.16 2440 2.0057.62 2450 2.1759.64 2460 2.4561.55 2470 2.3860.64 2480 2.5462.86 2490 2.3059.85 2500 2.4960.41 4 3.2RadiationPattern Phi02D Phi902D 5 Theta902D 2480MHz3D 6 4.AntennaDimensions 5.EUTPhoto 7 6.TestSetupPhoto

Silver Point Innovations LLC NY Add: 261 5th avenue Suite 1512 New York NY 10016 Tel: +1-917-669-1210 Email: [email protected] Attestation Letter Date: 2023-11-22 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir/Madam, We, Silver Point Innovations LLC NY hereby authorize China Certification ICT Co., Ltd (Dongguan) to act as a laboratory for testing and test report generation for the following project(s): (Product description: BDRV1, Model: BDRV1-SLVS, FCC ID: 2A2H2-BDRV1) The product supports 2.4GWiFi 802.11b/g/n ht20 and BLE Mode, But for this device, BLE 2M was disable by software. Sincerely, Signature: Printed Name: Sean Chraime Title: CPO

QA-FR-171-A Silver Point Innovations LLC NY Add: 261 5th avenue Suite 1512 New York NY 10016 Tel: +1-917-669-1210 Email: [email protected] FCC Confidential Authorization Date: 2023-11-22 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID:2A2H2-BDRV1 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, (Silver Point Innovations LLC NY) hereby requests long-term confidential treatment of information accompanying this application as outlined below: • Block Diagram • Schematics • Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature: Printed name: Sean Chraime Title: CPO

Date：2023-11-22 Product Model Number: BDRV1-SLVS FCC ID：2A2H2-BDRV1 To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following: •Testing •Approval applications and procedures We declare that ORGANIZATION. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out byORGANIZATION. on our behalf shall have the same effect as acts of our own. By: Sean Chraime Contact Listed on FCC Wesbite Title: CPO Email: [email protected] Telephone: +1-917-669-1210 On behalf of: Silver Point Innovations LLC NY Silver Point Innovations LLC NY A dd: 261 5th avenue Suite 1512 New York NY 10016 Tel: +1-917-669-12101210 Email: [email protected]

China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-EXP Page 1 of 5 EUT EXTERNAL PHOTOGRAPHS China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-EXP Page 2 of 5 China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-EXP Page 3 of 5 China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-EXP Page 4 of 5 Charger China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-EXP Page 5 of 5 Adapter

China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-INP Page 1 of 9 EUT INTERNAL PHOTOGRAPHS China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-INP Page 2 of 9 China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-INP Page 3 of 9 China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-INP Page 4 of 9 China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-INP Page 5 of 9 China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-INP Page 6 of 9 China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-INP Page 7 of 9 China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-INP Page 8 of 9 China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-INP Page 9 of 9 Antenna

RF EXPOSURE EVALUATION Applicant: Silver Point Innovations LLC NY Address: 261 5th avenue Suite 1512 New York NY 10016 FCC ID: 2A2H2-BDRV1 Product Name: BDRV1 Standard(s): 47 CFR §1.1310, 47 CFR §2.1091 447498 D01 General RF Exposure Guidance v06 The above device has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR231062634-00D Date Of Issue: 2023/11/23 Reviewed By: Julie Tan Title: RF Engineer Approved By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-00D Page 2 of 6 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-00D Page 3 of 6 CONTENTS DOCUMENT REVISION HISTORY .......................................................................................... 4 FCC§1.1310 & §2.1091- MAXIMUM PERMISSIBLE EXPOSURE (MPE) ............................... 5 1.1 APPLICABLE STANDARD ...................................................................................................................... 5 1.2 EUT INFORMATION▲: ........................................................................................................................ 6 1.3 MEASUREMENT RESULT ..................................................................................................................... 6 China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-00D Page 4 of 6 DOCUMENT REVISION HISTORY Revision Number Report Number Description of Revision Date of Revision 1.0 CR231062634-00D Original Report 2023/11/23 China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-00D Page 5 of 6 FCC§1.1310 & §2.1091- MAXIMUM PERMISSIBLE EXPOSURE (MPE) 1.1 Applicable Standard According to subpart §1.1310, systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Limits for Maximum Permissible Exposure (MPE) (§1.1310, §2.1091) (B) Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f²) 30 30–300 27.5 0.073 0.2 30 300–1500 / / f/1500 30 1500–100,000 / / 1.0 30 f = frequency in MHz; * = Plane-wave equivalent power density; According to §1.1310 and §2.1091 RF exposure is calculated. Calculation formula: Prediction of power density at the distance of the applicable MPE limit S = PG/4R² = power density (in appropriate units, e.g. mW/cm 2 ); P = power input to the antenna (in appropriate units, e.g., mW); G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor, is normally numeric gain; R = distance to the center of radiation of the antenna (appropriate units, e.g., cm); For simultaneously transmit system, the calculated power density should comply with: China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-00D Page 6 of 6 1.2 EUT Information▲: Operation Modes Operation Frequency (MHz) Max Conducted output power including Tune-up Tolerance (dBm) Maximum Antenna Gain (dBi) BLE 2402-248072.54 2.4G WLAN 2412-246225.52.54 Note: The Above Parameters were provided by the manufacturer. 1.3 Measurement Result Operation Modes Frequency (MHz) Antenna Gain Conducted output power including Tune-up Tolerance Evaluation Distance Power Density MPE Limit (dBi) (numeric)(dBm) (mW) (cm) (mW/cm 2 )(mW/cm 2 ) BLE 2402-2480 2.54 1.79 7 5.01 20.00 0.0018 1 2.4G WLAN 2412-2462 2.54 1.79 25.5 354.81 20.00 0.1268 1 Note: The BLE/2.4G WLAN can’t transmit simultaneously. Result: The device compliant the Exemption at 20cm distances. ===== END OF REPORT =====

TEST REPORT Applicant: Silver Point Innovations LLC NY Address: 261 5th avenue Suite 1512 New York NY 10016 FCC ID: 2A2H2-BDRV1 Product Name: BDRV1 Standard(s): 47 CFR Part 15, Subpart C(15.247) ANSI C63.10-2013 KDB 558074 D01 15.247 Meas Guidance v05r02 The above device has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR231062634-00A Date Of Issue: 2023/11/23 Reviewed By: Julie Tan Title: RF Engineer Approved By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-00A Page 2 of 51 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-00A Page 3 of 51 CONTENTS DOCUMENT REVISION HISTORY .......................................................................................... 5 1. GENERAL INFORMATION .................................................................................................... 6 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................... 6 1.2 DESCRIPTION OF TEST CONFIGURATION ........................................................................................... 8 1.2.1 EUT Operation Condition: ............................................................................................................................. 8 1.2.2 Support Equipment List and Details .............................................................................................................. 8 1.2.3 Support Cable List and Details ...................................................................................................................... 8 1.2.4 Block Diagram of Test Setup ......................................................................................................................... 9 1.3 MEASUREMENT UNCERTAINTY ........................................................................................................ 10 2. SUMMARY OF TEST RESULTS .......................................................................................... 11 3. REQUIREMENTS AND TEST PROCEDURES .................................................................. 12 3.1 AC LINE CONDUCTED EMISSIONS .................................................................................................... 12 3.1.1 Applicable Standard ..................................................................................................................................... 12 3.1.2 EUT Setup.................................................................................................................................................... 13 3.1.3 EMI Test Receiver Setup ............................................................................................................................. 13 3.1.4 Test Procedure ............................................................................................................................................. 14 3.1.5 Corrected Amplitude & Margin Calculation ................................................................................................ 14 3.2 RADIATION SPURIOUS EMISSIONS .................................................................................................... 15 3.2.1 Applicable Standard ..................................................................................................................................... 15 3.2.2 EUT Setup.................................................................................................................................................... 15 3.2.3 EMI Test Receiver & Spectrum Analyzer Setup ......................................................................................... 16 3.2.4 Test Procedure ............................................................................................................................................. 17 3.2.5 Corrected Amplitude & Margin Calculation ................................................................................................ 17 3.3 MINIMUM 6 DB BANDWIDTH ............................................................................................................. 18 3.3.1 Applicable Standard ..................................................................................................................................... 18 3.3.2 EUT Setup................................................................................................................................................…

Text truncated - open the document above for the full version.

TEST REPORT Applicant: Silver Point Innovations LLC NY Address: 261 5th avenue Suite 1512 New York NY 10016 FCC ID: 2A2H2-BDRV1 Product Name: BDRV1 Standard(s): 47 CFR Part 15, Subpart C(15.247) ANSI C63.10-2013 KDB 558074 D01 15.247 Meas Guidance v05r02 The above device has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR231062634-00C Date Of Issue: 2023/11/23 Reviewed By: Julie Tan Title: RF Engineer Approved By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-00C Page 2 of 64 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR231062634-00C Page 3 of 64 CONTENTS DOCUMENT REVISION HISTORY .......................................................................................... 5 1. GENERAL INFORMATION .................................................................................................... 6 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................... 6 1.2 DESCRIPTION OF TEST CONFIGURATION ........................................................................................... 8 1.2.1 EUT Operation Condition: ............................................................................................................................. 8 1.2.2 Support Equipment List and Details .............................................................................................................. 8 1.2.3 Support Cable List and Details ...................................................................................................................... 8 1.2.4 Block Diagram of Test Setup ......................................................................................................................... 9 1.3 MEASUREMENT UNCERTAINTY ........................................................................................................ 10 2. SUMMARY OF TEST RESULTS .......................................................................................... 11 3. REQUIREMENTS AND TEST PROCEDURES .................................................................. 12 3.1 AC LINE CONDUCTED EMISSIONS .................................................................................................... 12 3.1.1 Applicable Standard ..................................................................................................................................... 12 3.1.2 EUT Setup.................................................................................................................................................... 13 3.1.3 EMI Test Receiver Setup ..................................................................................................................…

Text truncated - open the document above for the full version.