2A2T9-LP01008Desk Lamp

FCC Warning Statement Changes or m odifications not e xpressly a pproved by t he p arty r esponsible for compliance could void t he u ser’s authority to o perate the e quipment. This equipment has been tested and found to c omply with t he l imits for a Class B digital device, pursuant to P art 1 5 o f t he F CC Rules. These limits are d esigned to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, i f not installed and u sed i n a ccordance with t he instructions, may c ause harmful interference to r adio communications. However, there is no guarantee that interference will n ot occur in a p articular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off a nd o n, t he user is encouraged to t ry t o c orrect the interference by o ne or more of t he f ollowing measures: ‐‐ Reorient or r elocate the receiving antenna. ‐‐ Increase the s eparation between the equipment and r eceiver. ‐‐ Connect the equipment into a n o utlet on a c ircuit different from t hat t o which the r eceiver is connected. ‐‐ Consult the dealer or a n experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interfe rence that may cause undesired operation. RF Exposure: A distance of 15 cm shall be maintained between the an tenna and us ers, and the transmitter may no t be co‐located with any other transmitter or antenna.

Co m Ad d She Pr o Mo d LP0 Pr o We act We an d issu our Sig Na m Title Com mpany: Sh dress: Rm. enzhen, Ch oduct Name del Numbe 01015, LP0 oduct Desc authorize M on our beha declare tha d certificatio ues concern behalf shal nature: me: e: mpany: enzhen Ina 2507, Bldg hina e: Desk Lam er(s): LP010 1016, LP01 ription: De MiCOM Lab alf on all ma at MiCOM L n of equipm ning the app ll have the s Harvey Y a Product M Shenzhen Shenzhen Agen ateck Tech g. 11, TianA mp 008, LP010 1017, LP01 esk Lamp bs Inc., 575 atters conce Labs Inc. is ment to the r proval applic same effect an Manager n Inateck Te Inateck Te nt Auth nology Co An Cloud P 009, LP0101 018, LP010 Boulder Co erning the c allowed to f regulatory a cation. Any t as acts of echnology C echnology C horizat ., Ltd. Park, Bantia 10, LP0101 019, LP010 ourt, Pleasa certification forward all i agencies as and all acts our own. Co., Ltd. Co., Ltd. tion an Street, L 1, LP01012 20 anton, Califo of above na information s required a s carried ou Date: Longgang 2, LP01013 ornia 94566 amed equip related to t nd to discu ut by MiCOM Aug. 25, 20 District, 3, LP01014, 6, USA, to pment. the approva ss any M Labs on 021 , al

Office o Federa 7435 O Columb USA Subjec t FCC ID To Wh o Pursua are req u docume These d propriet might b It is ou r corresp docume authoriz Sincer e Signat u Name: Title: P r of Engineeri l Communic Oakland Mills bia, MD 210 t; Request f D: 2A2T9-LP om It May C nt to the pro uesting the ents from pu documents tary informa be harmful to Schema Block D Parts Lis Operatio r understand pondence du ents and thi zation is iss ely, ure: Harvey Yan roduct Man Sh ing Techno cations Com s Road 046 for Confiden P01008 Concern, ovisions of t Commissio ublic disclos contain det ation in ope o our comp atic Diagram iagram st onal Descri ding that all uring the ce s informatio sued. n age r henzhen Ina logy mmission ntiality the Commis on to withho sure indefin tailed syste ration of th e any and wo m ption l measurem ertification re on will be av ateck Tech ssion’s rule old the follow nitely. m and equi e equipmen ould give co ment test rep eview proce vailable for hnology Co s Title 47 S wing attach pment desc nt. The publ ompetitors a ports, FCC ess cannot public revi e o., Ltd. Sections §0. hment(s) as criptions an ic disclosu r an unfair ad ID label for be granted ew once the Date: Aug. 457 and §0 confidentia d are consi re of these d vantage in mat and as confide n e grant of eq 25, 2021 0.459, we al dered as documents the market . ntial quipment .

Model Difference Declaration To Whom It May Concern, We, Shenzhen Inateck Technology Co., Ltd.(DeskLamp) Trademark:N/A; Model Number:LP01008, LP01009, LP01010, LP01011, LP01012, LP01013, LP01014, LP01015, LP01016, LP01017, LP01018, LP01019, LP01020;All model’s the function, software and electric circuit are the same, only with a product color, appearance and model named different for commercial purpose. Test sample model:LP01008. Please contact me if you have any question. Name: Harvey Yan Date: Aug. 25, 2021 Title:Product Manager Signature of applicant:

Annex A External Photos Report No.: HK2107122312‐1E/2E Page 1 of 4 Report No.: HK2107122312‐1E/2E Page 2 of 4 Report No.: HK2107122312‐1E/2E Page 3 of 4 Report No.: HK2107122312‐1E/2E Page 4 of 4

FCC ID: 2A2T9-LP01008

Annex B Internal Photo Report No.:HK2107122312-1E/2E Page 1 of 5 Coil Antenna Report No.:HK2107122312-1E/2E Page 2 of 5 Report No.:HK2107122312-1E/2E Page 3 of 5 Report No.:HK2107122312-1E/2E Page 4 of 5 Report No.:HK2107122312-1E/2E Page 5 of 5

Page 1 of 8 Report No.: HK2107122312-2E FCC TEST REPORT Test report On Behalf of Shenzhen Inateck Technology Co., Ltd. For Desk Lamp Model No.: LP01008, LP01009, LP01010, LP01011, LP01012, LP01013, LP01014, LP01015, LP01016, LP01017, LP01018, LP01019, LP01020 FCC ID: 2A2T9-LP01008 Prepared For : Shenzhen Inateck Technology Co., Ltd. Rm. 2507, Bldg. 11, TianAn Cloud Park, Bantian Street, Longgang District, Shenzhen, China Prepared By : Shenzhen HUAK Testing Technology Co., Ltd. 1-2/F., Building B2, Junfeng Zhongcheng Zhizao Innovation Park, Heping, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Date of Test: July. 12, 2021 ~Aug. 11, 2021 Date of Report: Aug. 11, 2021 Report Number: HK2107122312-2E Page 2 of 8 Report No.: HK2107122312-2E Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. 2. Channel List Channel Frequency (KHz) Channel Frequency (MHz) Channel Frequency (MHz) Channel Frequency (MHz) 01 125 The EUT antenna is Coil Antenna. No antenna other than that furnished by the responsible party shall be used with the device. 2. SUMMARY OF TEST RESULTS 2.1. Test Procedures According to The Technical Standards: FCC KDB680106 D01 RF Exposure Wireless Charging Apps v03 FCC CFR 47 Standard Section Test Item Judgment Remark FCC CFR 47 part1, 1.1310 KDB680106 D01v03 (3)(3) Electric Field Strength (E) (V/m) PASS Magnetic Field Strength (H) (A/m) PASS 2.2. Measurement Uncertainty The reported uncertainty of measurement y ±U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 All emissions, radiated(<30M)(9KHz-30MHz) ±3.90dB 2 Temperature ±0.5°C 3 Humidity ±2% Page 3 of 8 Report No.: HK2107122312-2E 2.3. Test Instruments Description Brand Model No. Frequency Range Calibrated Date Calibrated Until Broadband Field Meter NARDA NBM-550- Dec. 10, 2020 Dec. 09, 2021 Magnetic Field Meter NARDA ELT-400 1 – 400kHz Dec. 10, 2020 Dec. 09, 2021 Magnetic Probe NARDA HF-3061 300kHz – 30MHz Dec. 10, 2020 Dec. 09, 2021 Magnetic Probe NARDA HF-0191 27 – 1000MHz Dec. 10, 2020 Dec. 09, 2021 Broadband Field Meter NARDA NBM-550- Dec. 10, 2020 Dec. 09, 2021 Electric Field Meter COMBINOVA EFM 2005Hz – 400kHzDec. 10, 2020 Dec. 09, 2021 E-Field Probe NARDA EF-0391 100kHz – 3GHz Dec. 10, 2020 Dec. 09, 2021 E-Field Probe NARDA EF-6091 100MHz – 60GHz Dec. 10, 2020 Dec. 09, 2021 lsotropic Electric Field| Probe NARDA EP-601 511WX60706 Dec. 10, 2020 Dec. 09, 2021 NOTE: 1. The calibration interval of the above test instruments is 12 months . Page 4 of 8 Report No.: HK2107122312-2E 3. MAXIMUM PERMISSIBLE EXPOSURE Limit of Maximum Permissible Exposure Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180 / f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1 30 Note 1: f = frequency in MHz ; *Plane-wave equivalent power density. Note 2: For the applicable limit, see FCC 1.1310, 680106 D01 RF Exposure Wireless Charging Apps v03. Note 3: Emissions between 100 kHz to 300 kHz should be assessed versus the limits at 300 kHz in Table 1 of Section 1.1310: 614 V/m and 1.63A/m. A KDB inquiry is required to determine the applicable exposure limits below 100 kHz. Page 5 of 8 Report No.: HK2107122312-2E 4. TEST PROCEDURE a. For devices designed for typical desktop applications, such a wireless charging pads, RF exposure evaluation should be conducted assuming a user separation distance of (H-field & E- field strengths for all sides is 15cm, H-field strengths of top side is 20cm). E and H field strength measurements or numerical modeling may be used to demonstrate compliance. Measurements should be made from all sides and the top of the primary/client pair, with the 15 cm measured from the center of the probe(s) to the edge of the device. 4.1 Test Setup 4.2 Result of Maximum Permissible Exposure Page 6 of 8 Report No.: HK2107122312-2E For Full load mode: E-Field Strength at 15 cm from the edges surrounding the EUT (V/m) Frequency Range (MHz) Test Position A Test Position B Test Position C Test Position D Test Position E Limits Test (V/m) 0.125 1.78 1.69 1.33 1.52 1.49 614 H-Field Strength at 15 cm from the edges surrounding the EUT (A/m) Frequency Range (MHz) Test Position A Test Position B Test Position C Test Position D Test Position E Limits Test (A/m) 0.125 0.16 0.27 0.19 0.26 0.15 1.63 For Half Load mode: E-Field Strength at 15 cm from the edges surrounding the EUT (V/m) Frequency Range (MHz) Test Position A Test Position B Test Position C Test Position D Test Position E Limits Test (V/m) 0.125 1.75 1.63 1.58 1.32 1.46 614 H-Field Strength at 15 cm from the edges surrounding the EUT (A/m) Frequency Range (MHz) Test Position A Test Position B Test Position C Test Position D Test Position E Limits Test (A/m) 0.125 0.17 0.23 0.21 0.16 0.14 1.63 Page 7 of 8 Report No.: HK2107122312-2E For No load mode: E-Field Strength at 15 cm from the edges surrounding the EUT (V/m) Frequency Range (MHz) Test Position A Test Position B Test Position C Test Position D Test Position E Limits Test (V/m) 0.125 1.72 1.62 1.69 1.21 1.46 614 H-Field Strength at 15 cm from the edges surrounding the EUT (A/m) Frequency Range (MHz) Test Position A Test Position B Test Position C Test Position D Test Position E Limits Test (A/m) 0.125 0.26 0.19 0.17 0.22 0.13 1.63 Remark: According KDB 680106 D01 RF Exposure Wireless…

Text truncated - open the document above for the full version.

Page 1 of 20 Report No.: HK2107122312-1E FCC TEST REPORT Test report On Behalf of Shenzhen Inateck Technology Co., Ltd. For Desk Lamp Model No.: LP01008, LP01009, LP01010, LP01011, LP01012, LP01013, LP01014, LP01015, LP01016, LP01017, LP01018, LP01019, LP01020 FCC ID: 2A2T9-LP01008 Prepared For : Shenzhen Inateck Technology Co., Ltd. Rm. 2507, Bldg. 11, TianAn Cloud Park, Bantian Street, Longgang District, Shenzhen, China Prepared By : Shenzhen HUAK Testing Technology Co., Ltd. 1-2/F., Building B2, Junfeng Zhongcheng Zhizao Innovation Park, Heping, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Date of Test: July. 12, 2021 ~Aug. 11, 2021 Date of Report: Aug. 11, 2021 Report Number: HK2107122312-1E Page 2 of 20 Report No.: HK2107122312-1E TEST RESULT CERTIFICATION Applicant’s name ................. : Shenzhen Inateck Technology Co., Ltd. Address ................................. : Rm. 2507, Bldg. 11, TianAn Cloud Park, Bantian Street, Longgang District, Shenzhen, China Manufacture's Name ............ : Shenzhen Inateck Technology Co., Ltd. Address ................................. : Rm. 2507, Bldg. 11, TianAn Cloud Park, Bantian Street, Longgang District, Shenzhen, China Product description Trade Mark: N/A Product name ........................... : Desk Lamp Model and/or type reference : LP01008, LP01009, LP01010, LP01011, LP01012, LP01013, LP01014, LP01015, LP01016, LP01017, LP01018, LP01019, LP01020 Standards ............................. : FCC Rules and Regulations Part 15 Subpart C (Section 15.209), ANSI C63.10: 2013 This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen HUAK Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen HUAK Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Date of Test ............................................ : Date (s) of performance of tests ............. : July. 12, 2021 ~ Aug. 11, 2021 Date of Issue ........................................... : Aug. 11, 2021 Test Result ............................................... : Pass Testing Engineer : (Gary Qian) Technical Manager : (Eden Hu) Authorized Signatory : (Jason Zhou) Page 3 of 20 Report No.: HK2107122312-1E Table of Contents Page 1 . TEST SUMMARY 5 1.1 . Test Procedures and Results 5 1.2 . Test Facility 5 1.3 . Measurement Uncertainty 5 2. GENERAL INFORMATION 6 2.1. General Description of EUT 6 2.2. Carrier Frequency of Channels 7 2.3. Operation of EUT During Testing 7 2.4. Description of Test Setup 7 2.5. Measurement Instruments List 8 3. CONDUCTED EMISSION TEST 9 3.1. Block Diagram of Test Setup 9 3.2. Conducted Power Line Emission Limit 9 3.3. Test Procedure 9 3.4. Test Result 10 4. RADIA TED EMISSIONS 12 4.1. Block Diagram of Test Setup 12 4.2. Rules and Specifications 13 4.3. Test Procedure 14 4.4. Test Result 14 5. ANTENNA REQUIREMENT 17 6. PHOTOGRAPH OF TEST 18 7. PHOTOS OF THE EUT 20 Page 4 of 20 Report No.: HK2107122312-1E ** Modified History ** Revision Description Issued Data Remark Revision 1.0 Initial Test Report Release Aug. 11, 2021 Jason Zhou Page 5 of 20 Report No.: HK2107122312-1E 1. TEST SUMMARY 1.1. Test Procedures and Results DESCRIPTION OF TEST SECTION NUMBERRESULT CONDUCTED EMISSIONS TEST 15.207 COMPLIANT RADIATED EMISSION TEST 15.209 COMPLIANT ANTENNA REQUIREMENT 15.203 COMPLIANT Note: 1. PASS: Test item meets the requirement. 2. Fail: Test item does not meet the requirement. 3. N/A: Test case does not apply to the test object. 4. The test result judgment is decided by the limit of test standard. 1.2. Test Facility Test Firm : Shenzhen HUAK Testing Technology Co., Ltd. Address : 1-2/F., Building B2, Junfeng Zhongcheng Zhizao Innovation Park, Heping, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China 1.3. Measurement Uncertainty Measurement Uncertainty Conducted Emission Expanded Uncertainty =2.71dB, k=2 Radiated emission expanded uncertainty(9kHz-30MHz) = 3.90dB, k=2 Radiated emission expanded uncertainty(30MHz-1000MHz)= 3.90dB, k=2 Radiated emission expanded uncertainty(Above 1GHz) = 4.28dB, k=2 Page 6 of 20 Report No.: HK2107122312-1E 2. GENERAL INFORMATION 2.1. General Description of EUT Equipment: Desk Lamp Model Name: LP01008 Serial No.: LP01009, LP01010, LP01011, LP01012, LP01013, LP01014, LP01015, LP01016, LP01017, LP01018, LP01019, LP01020 Model Difference: All model’s the function, software and electric circuit are the same, only with a product color, appearance and model named different. Test sample model: LP01008. Trade Mark: N/A FCC ID: 2A2T9-LP01008 Antenna Type: Coil Antenna Antenna Gain: 0dBi Operation frequency: 125KHz Number of Channels: 1 Modulation Type: ASK Power Source: 12V, 2A From Adapter with AC100-240V, 50/60Hz, 0.8A Wireless Charger: 9V, 1.1A USB Charger: 5V, 2A Max Power Rating: 12V, 2A From Adapter with AC100-240V, 50/60Hz, 0.8A Wireless Charger: 9V, 1.1A USB Charger: 5V, 2A Max Page 7 of 20 Report No.: HK2107122312-1E 2.2. Carrier Frequency of Channels Operation Frequency each of channel Channel Frequency 1 125KHz 2.3. Operation of EUT During Testing Operating Mode The mode is used: Transmitting mode 2.4. Description of Test Setup Operation of EUT during testing: AC Plug Adapter information Model: AS024-1202000U Input: 100-240V, 50-60Hz, 0.8A Output: 12V, 2A Mobile phone information Model: m2011k2c The sample was placed (0.8m (30MHz~1GHz), 0.8m (9KHz~30MHz) ) above the ground plane of 3m chamber. Measurements in both horizontal and vertical polarities were performed. During the test, each emission was maximized by: having the EUT continuously working, investigated all operating modes, rotated about all 3 axis (X, Y & Z) and considered typical configuration to obtain worst position, manipulating interconnecting cables, rotating the turntable, varying antenna height from 1m to 4m in …

Text truncated - open the document above for the full version.

Radiated Emissions Conducted Emission