2A2UNMG1100DIGITAL PROPORTIONAL RADIO CONTROL SYSTEM

Quick Start Guide 快速操作指南 MG11 发射机概览 发射机概览 注意事项 ！ 开始操作前请务必阅读以下安全信息！ • 请不要在夜晚或雷雨天气使用本产品，恶劣的天气环境有可能导致遥控设备失灵。 • 请不要在能见度有限的情况下使用本产品。 • 请不要在雨雪或有水的地方使用本产品。如果有液体进入到系统内部，可能会导致运行不稳定 或设备失灵。 • 信号干扰可能导致设备失控。为保证您和他人的安全，请不要在以下地点使用本产品： 感谢您购买富斯公司的产品！欲知更多产品信息，请浏览以下官方网站： www.flyskytech.com. 如果您在使用中遇到任何问题，请先查阅发射机使用说明书。 如果问题仍未得到解决，请直接联 系当地经销商或者访问官网联系客服人员。 • 当你感到疲倦、不舒服，或在摄入酒精或服食导致麻醉或兴奋的药物后，不要操作本产品， 否则可能对自己或他人造成严重的伤害。 • 2.4GHz 无线电波段完全不同于之前所使用的低频无线电波段。使用时请确保模型产品在您 的视线范围内飞行，大的障碍物将会阻断无线电频率信号从而导致遥控失灵模型失控。 • 在使用过程中，严禁紧握发射机天线，否则将会大大减弱无线电传播信号的质量和强度， 导 致遥控失灵模型失控。 • 在操作或使用模型后，请勿触摸任何可能发热的部位，如发动机、电机、定速设定等。这些 部件可能非常热，容易造成严重的烧伤。 • 遥控设备使用不恰当可能导致操作者或他人严重受伤，甚至死亡。为保证您和设备的安全， 请仔细阅读使用说明书并按照要求进行操作。 • 使用前必须确保本产品与模型安装正确，否则可能导致模型发生严重损坏。 • 操控时，请先确认模型所有舵机的动作方向与操控方向一致。如果不一致，请调整好正确的 方向。 • 当遥控距离持续较远时，有发生失控的可能。请适当缩短遥控的距离。 • 特此，【Flysky Technology Co., Ltd.】声明无线电设备【FS-MG11-BS】符合 RED2014/53/ EU. 欧盟 DoC 声明、FCC 声明可在以下互联网地址：www.flyskytech.com/info_detail/10. html 获取。 • 安装于此发射机的天线必须与人保持至少 20cm 的距离，同时禁止将其用于其他发射机上， 用户或者安装人员需要在满足 RF 相关协议的天线安装说明及发射机操作指南的指导下进行 操作。 基本操作 AA 电池安装 请按照以下步骤安装 AA 电池： 1. 打开电池仓盖（如图所示）； 2. 将 4 颗电量充足的电池按标注的极性方向装入电池仓内； 3. 盖好电池仓盖。 Lipo 锂电池安装 请按照以下步骤安装锂电池： 1. 打开电池仓盖。 2. 将 2S 电量充足的锂电池放入电池仓内， 3. 将电池连接线接入 JST 接口，确保正确连接正负极； 4. 盖好电池仓盖，注意不要夹到电池连接线。 开机 请按照以下步骤打开发射机： 1. 检查系统状态，确保电池电量充足且安装正确； 2. 将电源开关拨到 [ON] 位置，G.LED 指示灯常亮，氛围灯和 BATT 指示灯亮 3 秒后灭。 1. 将发射机按住对码按键（BIND）开机即进入对码状态，此时 G.LED 指示灯快闪，松开对码 按键 ; 2. 接收机上电等待 1 秒没有连接即自动进入对码状态，此时接收机 LED 快闪； 3. 对码成功后 , 接收机 LED 指示灯及发射机 G.LED 指示灯常亮； 4. 检查发射机、接收机是否正常工作。如需重新对码，请重复以上步骤。 注：此对码步骤仅适用于 FS-MG11-BS 发射机与 FS-R11D-ESC-BS 接收机对码。不同的接收 机对码方式不同，具体对码方式请访问 FLYSKY 官网查询接收机说明书或其他相关资料。 对码 本发射机和接收机在出厂前已对码成功。若需使用其他的接收机，请按照如下步骤进行对码。 本发射机支持双向对码，对码步骤如下： 按住此处并向前滑动，取下电 池舱盖。 FS-MG11-BS 自动跳频数字系统 规格参数 关闭发射机之前，请务必先断开接收机电源，然后关闭发射机。如果强行关闭发射机，将 会导致遥控设备失控，失控保护设置不合理可能引起事故。 产品型号 MG11 适配接收机FS-R11D-ESC-BS、FS-R11P-BS 适配模型车 通道个数11 无线频率2.4GHz ISM 发射功率<20dBm 无线标准2A-BS 通道分辨率4096 级 输入电源1.5AA*4 或 2S 锂电池 工作电流60mA 左右 /6V 低电压报警AA 电池：<4.2V；LiPo 电池：<7.0V 天线类型内置单天线 充电接口无（USB 接口仅做供电使用 ) 在线更新无 数据输出无 遥控距离﹥ 150m( 空旷无干扰地面距离 ) 温度范围-10°C ~ +60°C 湿度范围20% ~ 95％ 外形尺寸135.7*189.5*82.7mm 机身重量225g 外观颜色黑色 安全认证CE，FCC ID: 2A2UNMG1100 关机 请按以下步骤关闭发射机： 1. 先断开接收机电源； 2. 将电源开关拨到 [OFF] 位置，关闭发射机。 此功能用于当接收机无法正常收到发射机的信号不受控制时，保护模型和操作人员的安全。 可在发射机端设置相应的失控保护值。默认未设置，未设置时 PWM 接口保持最后输出。设置 步骤如下： 开机正常状态下，先操作需要设置失控保护的通道所对应的控件至预设的位置，再长按 BIND 键 3 秒，即将当下输出的通道值设置为失控保护值。 注： 1. 当发射机对码二合一接收机时，接收机 CH2 通道默认开启失控保护，失控后电调进入刹车 模式。而其他通道可在发射机端设置相应的失控保护值，设置方法同上。 2. 重新对码时恢复默认设置。 失控保护 摇杆校准 当油门、手轮和 CH5 旋钮发生机械性偏离，如回中或最大 / 最小行程出现偏差时，使用此功 能修正。步骤如下： 1. 同步将手轮顺时针打到最大、扳机往前推到底并开机，进入校准模式，发射机蜂鸣器响 3 声提示； 2. 手轮校准：将手轮分别按顺时针和逆时针方向转至最大和最小行程，发射机蜂鸣器响 2 声 提示； 3. 扳机校准：将扳机分别向前和向后推至最大和最小行程，发射机蜂鸣器响 1 声提示 ； 4. CH5 旋钮校准：将 CH5 旋钮分别按顺时针和逆时针方向转到最大和最小行程，发射机蜂 鸣器长响 1 声提示； 1. 注意锂电池不要过充 或过放。 2. 使用前请仔细阅读锂 电池使用说明书。 5. 按 BIND 键退出并保存校准数据，发射机蜂鸣器长响 1 声提示 。 若校准失败，按 BIND 键无反应，请重复以上校准步骤。 基站附近或其 他无线电活跃 的地方 人多的地方或 道路附近 有客船的水域高压电线或通信 广播天线附近 Http://www.flysky-cn.com Copyright © 2023 Flysky Technology Co., Ltd. Release date: 2023-06-30 FCC ID: 2A2UNMG1100 方向手轮（CH1) 油门扳机（CH2) CH3 按键（CH3)， 带蓝色指示灯 CH7 按键（CH7)， 带蓝色指示灯 CH4 按键（CH4)， 带蓝色指示灯 CH8 按键（CH8)， 带蓝色指示灯 油门通道反向开关 (TH.REV) RX 电量指示灯 (BATT） 对码按键（BIND） CH11& Drag Brake旋钮（CH11） 方向通道微调旋钮（ST.TRIM） 油门通道微调旋钮（TH.TRIM） CH10 自锁开关（CH10) 拨档开关（CH6） 挂绳孔 手柄 氛围灯 CH5 旋钮（CH5） CH9 旋钮（CH9） 六位拨码开关 USB 接口（Type-C） 状态指示灯绿色（G.LED） 方向通道比率调节旋钮 (ST.D/R) 油门通道比率调节旋钮 (TH.D/R) 电源开关（OFF/ON) 微调旋钮（TRIM） 方向通道反向开关（ST.REV） 电池仓 (4*AA 电池 /2S Lipo) • 注意：使用类型不正确的电池可能发生爆炸风险，请妥善处理使用完的电池。 Basic Operations Specifications Certifications Read the safety messages listed below before operation! • Do not use the product at night or during bad weather conditions, like rain or thunderstorms. It can cause erratic operation or loss of control. • Do not use the product when visibility is limited. • Do not expose the product to rain or snow. Any exposure to moisture (water or snow) may cause erratic operation or loss of control. • Interference may cause loss of control. To ensure the safety of you and others, do not operate in the following places: Thank you for purchasing the products of Flysky! To find out more about our products, visit our website at www.flysky-cn.com. If you encounter any problems during using, please refer to the manual first. If the problem is still not resolved, consult your local dealer directly or contact the customer service staff via Flysky official website. • Do not use this product when you are tired, uncomfortable, or under the influence of alcohol or drugs. Doing so may cause serious injury to yourself or others. • The 2.4GHz radio band is limited to line of sight. Always keep your model in sight as a large can block the RF signal and lead to loss of control. • Never grip the transmitter antenna during operation. It significantly degrades signal quality and strength and may cause loss of control. • Do not touch any part of the model that may generate heat during operation, or immediately after use. The engine, motor or speed control, may be very hot and can cause serious burns. • Misuse of this product may lead to serious injury or death. To ensure the safety of you and your equipment, read this manual and follow the instructions carefully. • Make sure the product is properly installed in your model. Failure to do so may result in serious injury. • Ensure that all servos operate in the correct direction. If not, adjust the direction first. • Make sure that the model stays within range in order to prevent loss of control. • The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-lacated or operating in conjunction with any other transmitter.End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. CAUTION! • RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Precautions Near any sites where other radio control activity may occur Near people or roads On any pond/ lake when …

Text truncated - open the document above for the full version.

ShenZhen FLYSKY Technology Co.,Ltd * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2A2UNMG1100 FRN of applicant: 0031248305 Per section 2.911(d)(7) of the FCC rules, ShenZhen FLYSKY Technology Co.,Ltd certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: Baihetian Innovative Solutions FCC Registration Number(FRN): 0033401605 Physical U.S. Company Address: 6837 Chase Rd, Dearborn, MI 48126, USA Contact Person: Kenneth Young Agent Email Address: [email protected] The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Signed: Printed name: Kyle Li Title: RD Manager Company Name: ShenZhen FLYSKY Technology Co.,Ltd Date: 7/21/2023 Agent Signed (if different to Applicant): Signed: Printed name: Kenneth Young Title: Manager Company Name: Baihetian Innovative Solutions Date: 7/21/2023

ShenZhen FLYSKY Technology Co.,Ltd Covered Equipment Certification Attestation Letter 7/21/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2A2UNMG1100 ShenZhen FLYSKY Technology Co.,Ltd certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. ShenZhen FLYSKY Technology Co.,Ltd certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Signed: Printed name: Kyle Li Title: RD Manager Company Name: ShenZhen FLYSKY Technology Co.,Ltd Date: 7/21/2023

DATE : 2023-07-21 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Jason Wu of Global United Technology Services Co., Ltd.and No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with ShenZhen FLYSKY Technology Co.,Ltd and 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China Signature: Name: Kyle Li Title: RD Manager Company: ShenZhen FLYSKY Technology Co.,Ltd

Differences Declaration To whom concern, We company ShenZhen FLYSKY Technology Co.,Ltd hereby declares: The product models MG11, FS-MG11-BS are identical in the same PCB layout, interior structure and electrical circuits, the only difference is the model name for commercial purpose. Authorized signature: Date: 2023-07-25

ShenZhen FLYSKY Technology Co.,Ltd DATE : 2023-07-21 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2A2UNMG1100 Product Name: DIGITAL PROPORTIONAL RADIO CONTROL SYSTEM Request for Confidentiality To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Signature: Name: Kyle Li Title: RD Manager

MADE IN CHINA Model No.: MG11 FCC ID: 2A2UNMG1100 Manufacturer: ShenZhen FLYSKY Technology Co.,Ltd Add: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 20230406 见图 / 01 FS-MG11-BS FS-MG11-BS认证信息刻字 / Adobe Illustrator CC 2018 李德平 产品经理确认

Test Model No.: MG11

FCC ID: 2A2UNMG1100 RF Exposure evaluation According to 447498 D04 Interim General RF Exposure Guidance v01 FCC ID: 2A2UNMG1100 Frequency (MHz) Output power to antenna (dBm) Ant gain(dBi) EIRP(dBm) ERP(dBm) ERP(mw) Distance (cm) P th (mW) 2475 8.92 1 9.92 7.77 5.98 1 10.2 ERP = EIRP −2.15 dB WORSE CASE 9.82mW<10.2mW Then SAR evaluation is not required Remark: The shortest distance between antenna and The manual part is 1cm.

Global United Technology Services Co., Ltd. Report No.: GTS2023060370F01 Authorized Signature: Robinson Luo Laboratory Manager This results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Page 1 of 35 TEST REPORT Applicant: ShenZhen FLYSKY Technology Co.,Ltd Address of Applicant: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China Manufacturer: ShenZhen FLYSKY Technology Co.,Ltd Address of Manufacturer: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China Factory: Dongguan Flysky RC Model technology Co.,Ltd Address of Factory: West building 3, HuangjinyuanInd Park, Qiaoli North Gate, Changping Town, Dongguan, China Equipment Under Test (EUT) Product Name: DIGITAL PROPORTIONAL RADIO CONTROL SYSTEM Model No.: MG11, FS-MG11-BS Trade Mark: FLYSKY FCC ID: 2A2UNMG1100 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Date of sample receipt: June 16, 2023 Date of Test: June 16, 2023-July 21, 2023 Date of report issued: July 21, 2023 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No.: GTS2023060370F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 35 2 Version Version No. Date Description 00 July 21, 2023 Original Prepared By: Date: July 21, 2023 Project Engineer Check By: Date: July 21, 2023 Reviewer Report No.: GTS2023060370F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 35 3 Contents Page 1 COVER PAGE ................................................................................................................................................ 1 2 VERSION ........................................................................................................................................................ 2 3 CONTENTS .................................................................................................................................................... 3 4 TEST SUMMARY ........................................................................................................................................... 4 4.1 MEASUREMENT UNCERTAINTY .................................................................................................................. 4 5 GENERAL INFORMATION ............................................................................................................................ 5 5.1 GENERAL DESCRIPTION OF EUT ............................................................................................................... 5 5.2 TEST MODE .............................................................................................................................................. 7 5.3 TEST FACILITY .......................................................................................................................................... 7 5.4 TEST LOCATION ....................................................................................................................................... 7 5.5 DESCRIPTION OF SUPPORT UNITS ............................................................................................................. 7 5.6 DEVIATION FROM STANDARDS ................................................................................................................... 7 5.7 ABNORMALITIES FROM STANDARD CONDITIONS ......................................................................................... 7 5.8 ADDITIONAL INSTRUCTIONS ....................................................................................................................... 7 6 TEST INSTRUMENTS LIST ........................................................................................................................... 8 7 TEST RESULTS AND MEASUREMENT DATA .......................................................................................... 10 7.1 ANTENNA REQUIREMENT ......................................................................................................................... 10 7.2 CONDUCTED PEAK OUTPUT POWER ........................................................................................................ 11 7.3 20DB EMISSION BANDWIDTH .................................................................................................................. 12 7.4 CARRIER FREQUENCIES SEPARATION ...................................................................................................... 13 7.5 HOPPING CHANNEL NUMBER .................................................................................................................. 14 7.6 DWELL TIME ........................................................................................................................................... 15 7.7 SPURIOUS EMISSION IN NON-RESTRICTED & RESTRICTED BANDS ............................................................. 16 7.7.1 Conducted Emission Method ........................................................................................................... 16 7.7.2 Radiated Emission Method .............................................................................................................. 17 8 TEST SETUP PHOTO .................................................................................................................................. 35 9 EUT CONSTRUCTION…

Text truncated - open the document above for the full version.

Report No.: GTS2023060370F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 1 of 10 AppendixA: 20dB Emission Bandwidth Test Result Test Mode Antenna Frequency[MHz] 20db EBW[MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict TX Ant1 2408 0.537 2407.709 2408.246 --- --- TX Ant1 2440 0.528 2439.715 2440.243 --- --- TX Ant1 2475 0.531 2474.712 2475.243 --- --- Test Graphs TX-Ant1-2408 TX-Ant1-2440 / TX-Ant1-2475 / Report No.: GTS2023060370F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 10 AppendixB: Occupied Channel Bandwidth Test Result Test Mode Antenna Frequency[MHz] OCB [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict TX Ant1 2408 0.71071 2407.5322 2408.2429 --- --- TX Ant1 2440 0.60240 2439.6434 2440.2458 --- --- TX Ant1 2475 0.72707 2474.5170 2475.2441 --- --- Test Graphs TX-Ant1-2408 TX-Ant1-2440 / TX-Ant1-2475 / Report No.: GTS2023060370F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 10 AppendixC: Maximum conducted output power Test Result Test Mode Antenna Frequency[MHz] Result[dBm] Limit[dBm] Verdict TX Ant1 2408 8.27 ≤20.97 PASS TX Ant1 2440 8.85 ≤20.97 PASS TX Ant1 2475 8.92 ≤20.97 PASS Test Graphs TX-Ant1-2408 TX-Ant1-2440 / TX-Ant1-2475 / Report No.: GTS2023060370F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 4 of 10 AppendixD: Carrier frequency separation Test Result Test Mode Antenna Frequency[MHz] Result[MHz] Limit[MHz] Verdict TX Ant1 Hop_2408 2.50 ≥0.537 PASS TX Ant1 Hop_2422.5 2.00 ≥0.537 PASS TX Ant1 Hop_2475 2.00 ≥0.537 PASS Test Graphs TX-Ant1-Hop-2408 TX-Ant1-Hop-2422.5 / TX-Ant1-Hop-2475 / Report No.: GTS2023060370F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 5 of 10 AppendixE: Time of occupancy Test Result Test Mode Antenna Frequency[MHz] BurstWidth [ms] Observation Period[s] TotalHops [Num] Result[s] Limit[s] Verdict TX Ant1 Hop_2439.5 0.771 6.4 124 0.09560 ≤0.4 PASS Test Graphs TX-Ant1-Hop-2439.5 TX-Ant1-Hop-2439.5 Report No.: GTS2023060370F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 6 of 10 AppendixF: Number of hopping channels Test Result Test Mode Antenna Frequency[MHz] Result[Num] Limit[Num] Verdict TX Ant1 Hop 16 ≥15 PASS Test Graphs TX-Ant1-Hop Report No.: GTS2023060370F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 7 of 10 AppendixG:Band edge measurements Test Result Test Mode Antenna ChName Frequency[MHz] Ref Level [dBm] Result [dBm] Limit [dBm] Verdict TX Ant1 Low 2408 8.11 -41.56 ≤-11.89 PASS TX Ant1 High 2475 8.91 -45.25 ≤-11.09 PASS TX Ant1 Low Hop_2408 6.63 -49.77 ≤-13.37 PASS TX Ant1 High Hop_2475 7.24 -52.46 ≤-12.76 PASS Test Graphs TX-Ant1-2408 TX-Ant1-2475 TX-Ant1-Hop_2408 TX-Ant1-Hop_2475 Report No.: GTS2023060370F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 8 of 10 AppendixH:Conducted Spurious Emission Test Result Test Mode Antenna Frequency[MHz] Freq Range [MHz] Ref Level [dBm] Result [dBm] Limit [dBm] Verdict TX Ant1 2408 0~Reference 8.11 8.11 --- PASS TX Ant1 2408 30~1000 8.11 -62.22 ≤-11.89 PASS TX Ant1 2408 1000~26500 8.11 -37.93 ≤-11.89 PASS TX Ant1 2440 0~Reference 8.77 8.77 --- PASS TX Ant1 2440 30~1000 8.77 -62.02 ≤-11.23 PASS TX Ant1 2440 1000~26500 8.77 -42.7 ≤-11.23 PASS TX Ant1 2475 0~Reference 8.90 8.90 --- PASS TX Ant1 2475 30~1000 8.90 -61.89 ≤-11.1 PASS TX Ant1 2475 1000~26500 8.90 -42.16 ≤-11.1 PASS Report No.: GTS2023060370F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 9 of 10 Test Graphs TX-Ant1-2408-0~Reference TX-Ant1-2408-30~1000 TX-Ant1-2408-1000~26500 TX-Ant1-2440-0~Reference TX-Ant1-2440-30~1000 TX-Ant1-2440-1000~26500 Report No.: GTS2023060370F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 10 of 10 TX-Ant1-2475-0~Reference TX-Ant1-2475-30~1000 TX-Ant1-2475-1000~26500 ---End---

Antenna describe 1.Antenna describe: Antenna plate PCB antenna Antenna gain 1.0dBi Frequency range 2.40GHZ-2.5GHZ Connector type direct Manufacturer:ShenzhenFLYSKY Technology Co.,Ltd. Antenna model: 2.Antenna Radiation Pattern Radiation [email protected] Antenna Max.Peak Gain:0.7dbi Freq.[MHZ] 2400 Eff.[%] 38.46 Antenna Max.Peak Gain 0.7dbi Minimum Peak Gain of Antenna -1.46dbi Radiation [email protected] Antenna Max.Peak Gain:1.0dbi Freq.[MHZ] 2450 Eff.[%] 43.35 Antenna Max.Peak Gain 1.0dbi Minimum Peak Gain of Antenna -0.65dbi Radiation [email protected] Antenna Max.Peak Gain:0.9dbi Freq.[MHZ] 2500 Eff.[%] 38.77 Antenna Max.Peak Gain 0.dbi Minimum Peak Gain of Antenna -1.07dbi

Test Model No.: MG11 Radiated Emission