2A2UNR11D0011-Channel Receiver

FS-R11D-ESC-BS 接收机 Receiver Http://www.flysky-cn.com Copyright ©2023 Flysky Technology Co., Ltd. • 产品型号：FS-R11D-ESC-BS • 适配发射机：FS-MG11-BS • 适配模型：1 /8 攀爬车、平路、越野短卡和卡车 • 通道个数：11 • 车灯组数：6（LED 车灯接口连接 FS-DB01 车灯驱动板） • 无线频率：2.4GHz ISM • 发射功率：< 20dBm • 无线协议：2A-BS • 天线类型：外置单天线（同轴天线） • 输入电源：LiPo（2~3S）/NiMH(5~9Cell) • BEC 输出：6V/5A • 持续 / 峰值电流：60A/240A • 支持电机类型：有刷电机 • 适配电机：370、390、540 或 550 有刷电机 • 数据输出：PWM • 通道分辨率：4096 • 温度范围：-10°C ~ +60°C • 湿度范围：20% ~ 95％ • 遥控距离：>150 米（空旷无干扰地面距离） • 防水等级：PPX7 • 在线更新：无 • 外形尺寸：44.0mm*30.0mm*16.7mm • 机身重量：45g • 认证： CE，FCC ID: 2A2UNR11D00 FS-R11D-ESC-BS 采用 2A-BS 协议，是一款带电调 和 LED 灯组控制的二合一 11 通道接收机。它具有 外置单天线，可输出 PWM 信号和车灯控制信号 , 能 够实现双向传输，通电自动对码，可在发射机端设 置电调的相关参数，可适配多种车型使用。 FS-R11D-ESC-BS, in compliance with 2A-BS protocol, is a 2-in-1 CH11 receiver combining the Electronic Speed Control (ESC) and LED light set control board. It is equipped with a single external antenna, with the output of PWM signals and car light control signals. It can realize two-way transmission, with binding automatically upon power-up. Users can set ESC parameters at the transmitter side. FS-R11D-ESC-BS can be adapted to a variety of car models. 产品介绍 Introduction 接收机概览 Receiver Overview 产品规格 Product Specifications [1] CH1 通道接口 [2] CH3 通道接口 [3] CH4 通道接口 [4] LED 车灯接口 [5] CH6 通道接口 [6] CH7 通道接口 [7] CH8 通道接口 [8] CH9 通道接口 [9] CH10 通道接口 [10] CH11 通道接口 [16] LED 指示灯 [17] 天线 [18] S ( 通道 / 车灯接口信号端 ) [19] "+" (通道/车灯接口正极） [20] "- "( 通道 / 车灯接口负极） • Product Name: FS-R11D-ESC-BS • Adaptive Transmitters: FS-MG11-BS • Adaptive Models: 1 /8 crawler, on-road car, off-road short course truck, and truck • Number of Channels: 11 • Number of Car Light Interfaces: 6 (LED car light interface connects to FS-DB01) • RF: 2.4GHz ISM • Maximum Power: < 20dBm (e.i.r.p.) （EU） • 2.4G Protocol: 2A-BS • Antenna: Single External Antenna(Coaxial Antenna) • Input Power: LiPo (2~3S)/NiMH(5~9Cell) • BEC Output: 6V/5A • Continuous / Peak Current: 60A/240A • Motor Type: Brushed Motor • Applicable Motors : 390, 370,540 or 550 Brushed Motor • Data Output: PWM • Resolution: 4096 • Temperature Range: -10°C ~ +60°C • Humidity Range: 20% ~ 95% • Distance: >150 M(Ground Distance without Interference) • WaterProof: PPX7 • Online Update: None • Dimensions: 44mm*30mm*16.7mm • Weight: 45g • Certifications: CE, FCC ID: 2A2UNR11D00 对码 Binding 本款接收机上电即自动进入对码状态。 1. 将发射机进入对码状态（发射机进入对码状态的方式 可能不同，请根据发射机的使用说明书进行操作）； 2. 接收机上电等待 1 秒没有连接将自动进入对码； 3. 对码成功后 , 接收机 LED 指示灯常亮 ; 4. 检查发射机、接收机是否正常工作。如需重新对码， 请重复以上步骤。 注： 1. 对码时请先将发射机进入对码状态，再将接收机进入 [6] CH7 [7] CH8 [8] CH9 [9] CH10 [10] CH11 [11] Heatsink [12] Motor Interface "-" [13] Battery Interface [14] Motor Interface "+" [15] Power Switch [11] 散热片 [12] 马达接口 "-" [13] 电池接口 [14] 马达接口 "+" [15] 电源开关 注： 1. 所有通道接口均采用标准 2.54mm*3 Pin 排针；电池接口采用 XT60 公头接口；马达接口采用 4.0 mm 子弹头母型接口。 2. LED 车灯接口用于连接 FS-DB01 车灯驱动板。 [1] [17] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [19] [20] [18] [1] CH1 Interface [2] CH3 Interface [3] CH4 Interface [4] LED Car Light Interface [5] CH6 Interface Notes: 1. All channel interfaces are 2.54mm*3 Pin standard pins, and the battery interface is XT60 male interface, and the spec of motor interface is a 4.0 mm bullet female connector. 2. The LED car light interface is used to connect FS-DB01 car light drive board. [16] LED [17] Antenna [18] S (CH/Car Light Interface Signal Pin) [19] "+"(CH/Car Light Interface Anode ) [20] "-" (CH/Car Light Interface Cathode) The receiver automatically enters the binding state once it is powered on. 1. First put the transmitter into the binding mode. (See the transmitter's user manual for instructions on how to activate binding mode.) 2. Turn on the receiver, and it will wait for 1 second for connection. If without connection, the receiver will enter the binding mode automatically. 3. After the binding is successful, the receiver LED is solid on. 4. Verify that the transmitter and receiver are working properly. If you need to re-bind, repeat the above steps. Notes: 1. Set the transmitter to its binding state first, and then set the receiver to FS-R11D-ESC-BS 接收机 Receiver Http://www.flysky-cn.com Copyright ©2023 Flysky Technology Co., Ltd. 车灯控制 Car Light Control 本接收机支持 6 组车灯：左转灯、右转灯、日行灯、前大灯、刹车灯和倒车灯（此 6 组车灯通过 FS-DB01 车灯驱动板与本接收机建立连接）。 车灯状态由 FS-MG11-BS 发射机的相应控件控制。左、右转向灯亮灭状态由手轮控制；日行灯和前大灯亮灭状态由 CH5 旋钮控制；刹车灯和倒车灯 亮灭状态由扳机控制。具体有如下所述： 车灯车灯状态控制状态控件触发条件备注 左转灯慢闪左转手轮逆时针打手轮 方向通道设置反向后对左、右转向灯无影响。 右转灯慢闪右转手轮顺时针打手轮 日行灯 常灭 /CH5 旋钮 CH5 旋钮位于左侧 常亮CH5 旋钮位于中间 常亮CH5 旋钮位于右侧 前大灯 常灭 /CH5 旋钮触发条件同日行灯常灭 常亮 刹车灯常亮刹车扳机前推扳机当电调运行模式设置为正转 / 反转模式时（无刹车），前推扳机刹车灯不亮。 倒车灯常亮倒车扳机前推扳机/ 注： 1. 接收机开机后，所有车灯常亮一秒后灭； 2. 方向通道 CH1 和油门通道 CH2 具有自动识别中位的功能 , 当调过微调后，需重新给接收机上电以完成中位自动识别。 Car LightsCar Light StateControl StateControlTrigger ConditionNotes Left Turn Signal Llight Slow FlashTurn Left Steering Wheel Turn the sterring wheel counterclockwise. If you set the steering channel in reverse, the trigger condition for left and right turn signal lights will not be affected. Right Turn Signa lLlight Slow FlashTurn Right Steering Wheel Turn the sterring wheel clockwise. Daytime Running Light OFF /CH5 Knob CH5 Knob is located at the left side. Solid ONCH5 Knob is located in the middle. Solid ONCH5 Knob is located at the right side. Headlight OFF /CH5 KnobSame as the DRL aboveOFF Solid ON Brake LightSolid ONBrakeTiggerPush the throttle trigger forward. When the running mode of ESC is set to Forward/Reverse mode (no brake), the Brake Light will not on when pushing the throttle trigger forward. Back LightSolid ONBack upTriggerPush the throttle trigger forward./ 左侧 右侧 Left Side Right Side 保护功能 Protection 本接收机具有电池电压过低和过高保护功能。 • 电压过低保护：当检测到电池电压过低时，CH2 通道无输出，所有车灯慢闪提示。 • 电压过高保护：当电池电压过高时，所有通道无输出，所有车灯快闪提示。 本接收机电调具有过热保护功能。 • 过热保护：当检测到电调内部温度过高时，CH2 通道无输出，所有车灯快闪提示；当温度正常后，通道恢复输出。 This receiver has low/high voltage protection function. • Low Voltage Protection: When the voltage is detected to be low, CH2 has no output and all the car lights flash slowly. • High Voltage Protection: When the voltage is detected to be high, all channels will…

Text truncated - open the document above for the full version.

ShenZhen FLYSKY Technology Co.,Ltd * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2A2UNR11D00 FRN of applicant: 0031248305 Per section 2.911(d)(7) of the FCC rules, ShenZhen FLYSKY Technology Co.,Ltd certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: Baihetian Innovative Solutions FCC Registration Number(FRN): 0033401605 Physical U.S. Company Address: 6837 Chase Rd, Dearborn, MI 48126, USA Contact Person: Kenneth Young Agent Email Address: [email protected] The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Signed: Printed name: Kyle Li Title: RD Manager Company Name: ShenZhen FLYSKY Technology Co.,Ltd Date: 7/6/2023 Agent Signed (if different to Applicant): Signed: Printed name: Kenneth Young Title: Manager Company Name: Baihetian Innovative Solutions Date: 7/6/2023

ShenZhen FLYSKY Technology Co.,Ltd Covered Equipment Certification Attestation Letter 7/6/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2A2UNR11D00 ShenZhen FLYSKY Technology Co.,Ltd certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. ShenZhen FLYSKY Technology Co.,Ltd certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Signed: Printed name: Kyle Li Title: RD Manager Company Name: ShenZhen FLYSKY Technology Co.,Ltd Date: 7/6/2023

DATE : 2023-07-06 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Jason Wu of Global United Technology Services Co., Ltd.and No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with ShenZhen FLYSKY Technology Co.,Ltd and 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China Signature: Name: Kyle Li Title: RD Manager Company: ShenZhen FLYSKY Technology Co.,Ltd

ShenZhen FLYSKY Technology Co.,Ltd DATE : 2023-07-06 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2A2UNR11D00 Product Name: 11-CHANNEL RECEIVER Request for Confidentiality To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Signature: Name: Kyle Li Title: RD Manager

Test Model No.: FS‐R11D‐ESC‐BS

20230420 0.175磨砂PC+3M9448A胶 01 彩色印刷 FS-R11D-ESC-BS FS-R11D-ESC-BS 接收机贴纸 Adobe Illustrator CC 2017 李德平 产品经理确认 PANTONE Black 6C White

Test Model No.: FS‐R11D‐ESC‐BS

FCC ID: 2A2UNR11D00 RF Exposure Evaluation Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3–3.0 614 1.63 *(100) 6 3.0–30 1842/f 4.89/f *(900/f 2 ) 6 30–300 61.4 0.163 1.0 6 300–1500 f/300 6 1500–100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f 2 ) 30 30–300 27.5 0.073 0.2 30 300–1500 f/1500 30 1500–100,000 1.0 30 f = frequency in MHz Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 , Pout = output power to antenna in mW; G = gain of antenna in linear scale, Pi = 3.1416; R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. FCC ID: 2A2UNR11D00 Test Result of RF Exposure Evaluation Channel Output power to antenna (dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm2) Limit (mW/cm2) Result 2440MHz 10.24 10.57 0.0016 1.0 PASS Remark: antenna gain=-1.11dBi

Global United Technology Services Co., Ltd. Report No.: GTS2023060372F01 Authorized Signature: Robinson Luo Laboratory Manager This results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Page 1 of 38 TEST REPORT Applicant: ShenZhen FLYSKY Technology Co.,Ltd Address of Applicant: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China Manufacturer: ShenZhen FLYSKY Technology Co.,Ltd Address of Manufacturer: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China Factory: Dongguan Flysky RC Model technology Co.,Ltd Address of Factory: West building 3, HuangjinyuanInd Park, Qiaoli North Gate, Changping Town, Dongguan, China Equipment Under Test (EUT) Product Name: 11-CHANNEL RECEIVER Model No.: FS-R11D-ESC-BS Trade Mark: FLYSKY FCC ID: 2A2UNR11D00 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Date of sample receipt: June 16, 2023 Date of Test: June 16, 2023-July 06, 2023 Date of report issued: July 06, 2023 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No.: GTS2023060372F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 38 2 Version Version No. Date Description 00 July 06, 2023 Original Prepared By: Date: July 06, 2023 Project Engineer Check By: Date: July 06, 2023 Reviewer Report No.: GTS2023060372F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 38 3 Contents Page 1 COVER PAGE ................................................................................................................................................ 1 2 VERSION ........................................................................................................................................................ 2 3 CONTENTS .................................................................................................................................................... 3 4 TEST SUMMARY ........................................................................................................................................... 4 4.1 MEASUREMENT UNCERTAINTY .................................................................................................................. 4 5 GENERAL INFORMATION ............................................................................................................................ 5 5.1 GENERAL DESCRIPTION OF EUT ............................................................................................................... 5 5.2 TEST MODE .............................................................................................................................................. 7 5.3 TEST FACILITY .......................................................................................................................................... 7 5.4 TEST LOCATION ....................................................................................................................................... 7 5.5 DESCRIPTION OF SUPPORT UNITS ............................................................................................................. 7 5.6 DEVIATION FROM STANDARDS ................................................................................................................... 7 5.7 ABNORMALITIES FROM STANDARD CONDITIONS ......................................................................................... 7 5.8 ADDITIONAL INSTRUCTIONS ....................................................................................................................... 7 6 TEST INSTRUMENTS LIST ........................................................................................................................... 8 7 TEST RESULTS AND MEASUREMENT DATA .......................................................................................... 10 7.1 ANTENNA REQUIREMENT ......................................................................................................................... 10 7.2 CONDUCTED EMISSIONS ......................................................................................................................... 11 7.3 CONDUCTED PEAK OUTPUT POWER ........................................................................................................ 14 7.4 20DB EMISSION BANDWIDTH .................................................................................................................. 15 7.5 CARRIER FREQUENCIES SEPARATION ...................................................................................................... 16 7.6 HOPPING CHANNEL NUMBER .................................................................................................................. 17 7.7 DWELL TIME ........................................................................................................................................... 18 7.8 SPURIOUS EMISSION IN NON-RESTRICTED & RESTRICTED BANDS ............................................................. 19 7.8.1 Conducted Emission Method ........................................................................................................... 19 7.8.2 Radiated Emission Method .............................................................................................................. 20 8 TEST SETUP PHOTO ...........................…

Text truncated - open the document above for the full version.

Report No.: GTS2023060372F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 1 of 10 AppendixA: 20dB Emission Bandwidth Test Result Test Mode Antenna Frequency[MHz] 20db EBW[MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict TX Ant1 2408 0.531 2407.727 2408.258 --- --- TX Ant1 2440 0.534 2439.730 2440.264 --- --- TX Ant1 2475 0.534 2474.727 2475.261 --- --- Test Graphs TX-Ant1-2408 TX-Ant1-2440 / TX-Ant1-2475 / Report No.: GTS2023060372F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 10 AppendixB: Occupied Channel Bandwidth Test Result Test Mode Antenna Frequency[MHz] OCB [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict TX Ant1 2408 0.53009 2407.7270 2408.2571 --- --- TX Ant1 2440 0.52600 2439.7291 2440.2551 --- --- TX Ant1 2475 0.52556 2474.7286 2475.2542 --- --- Test Graphs TX-Ant1-2408 TX-Ant1-2440 / TX-Ant1-2475 / Report No.: GTS2023060372F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 10 AppendixC: Maximum conducted output power Test Result Test Mode Antenna Frequency[MHz] Result[dBm] Limit[dBm] Verdict TX Ant1 2408 10.09 ≤20.97 PASS TX Ant1 2440 10.24 ≤20.97 PASS TX Ant1 2475 10.10 ≤20.97 PASS Test Graphs TX-Ant1-2408 TX-Ant1-2440 / TX-Ant1-2475 / Report No.: GTS2023060372F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 4 of 10 AppendixD: Carrier frequency separation Test Result Test Mode Antenna Frequency[MHz] Result[MHz] Limit[MHz] Verdict TX Ant1 Hop_2408 2.50 ≥0.534 PASS TX Ant1 Hop_2422.5 2.00 ≥0.534 PASS TX Ant1 Hop_2475 2.00 ≥0.534 PASS Test Graphs TX -Ant1-Hop-2408 TX -Ant1-Hop-2422.5 / TX -Ant1-Hop-2475 / Report No.: GTS2023060372F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 5 of 10 AppendixE: Time of occupancy Test Result Test Mode Antenna Frequency[MHz] BurstWidth [ms] Observation Period[s] TotalHops [Num] Result[s] Limit[s] Verdict TX Ant1 Hop_2439.5 0.771 6.4 9 0.0069 ≤0.4 PASS Test Graphs Tx-Ant1-Hop-2439.5 Tx-Ant1-Hop-2439.5 Report No.: GTS2023060372F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 6 of 10 AppendixF: Number of hopping channels Test Result Test Mode Antenna Frequency[MHz] Result[Num] Limit[Num] Verdict TX Ant1 Hop 16 ≥15 PASS Test Graphs / Tx-Ant1-Hop / Report No.: GTS2023060372F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 7 of 10 AppendixG:Band edge measurements Test Result Test Mode Antenna ChName Frequency[MHz] RefLevel [dBm] Result [dBm] Limit [dBm] Verdict TX Ant1 Low 2408 9.84 -43.39 ≤-10.16 PASS TX Ant1 High 2475 9.91 -45.76 ≤-10.09 PASS TX Ant1 Low Hop_2408 10.96 -48.55 ≤-9.04 PASS TX Ant1 High Hop_2475 11.03 -50.78 ≤-8.97 PASS Test Graphs TX-Ant1-2408 TX-Ant1-2475 TX-Ant1-Hop_2408 TX-Ant1-Hop_2475 Report No.: GTS2023060372F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 8 of 10 AppendixH:Conducted Spurious Emission Test Result Test Mode Antenna Frequency[MHz] FreqRange [MHz] RefLevel [dBm] Result [dBm] Limit [dBm] Verdict TX Ant1 2408 0~Reference 9.89 9.89 --- PASS TX Ant1 2408 30~1000 9.89 -61.17 ≤-10.11 PASS TX Ant1 2408 1000~26500 9.89 -45.38 ≤-10.11 PASS TX Ant1 2440 0~Reference 10.11 10.11 --- PASS TX Ant1 2440 30~1000 10.11 -62.29 ≤-9.89 PASS TX Ant1 2440 1000~26500 10.11 -42.63 ≤-9.89 PASS TX Ant1 2475 0~Reference 9.91 9.91 --- PASS TX Ant1 2475 30~1000 9.91 -61.14 ≤-10.09 PASS TX Ant1 2475 1000~26500 9.91 -42.98 ≤-10.09 PASS Report No.: GTS2023060372F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 9 of 10 Test Graphs TX-Ant1-2408-0~Reference TX-Ant1-2408-30~1000 TX-Ant1-2408-1000~26500 TX-Ant1-2440-0~Reference TX-Ant1-2440-30~1000 TX-Ant1-2440-1000~26500 Report No.: GTS2023060372F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 10 of 10 TX-Ant1-2475-0~Reference TX-Ant1-2475-30~1000 / TX-Ant1-2475-1000~26500 / ---End---

深圳市德威玛通讯设备有限公司 2 1.目的 objective 对于深圳市德威玛通讯设备有限公司出品的移动通信终端天线产品规格、测试方法 进行规范，避免因测试条件，方法的不同引起误差。 To standardize the product specifications and test methods of mobile communication terminal antenna produced by Shenzhen Devima Communication Equipment Co., LTD., to avoid errors caused by different test conditions and methods. 2.技术指标与实验设备technical index 2.1 技术指标technical index 产品电气性能指标 Electrical performance index of products 工作频率范围 operating frequency range 2400~2500MHz 驻波比 SWR 2400~2500MHz<5.0 天线增益 antenna gain 2400~2500MHz:-1.11dBi 辐射效率 radiant efficiency 2400~2500MHz>15% 阻抗 impedance 50ohm 产品材料说明 Product material Description 灰色1.13 同轴线100mm Gray 1.13 coaxial line 100mm 产品环境说明 Product Environment Description 工作温度 Operation Temperature - 30 ̊C ~ + 85 ̊C 储藏温度 Store Temperature - 30 ̊C ~ + 85 ̊C 深圳市德威玛通讯设备有限公司 3 3. 产品结构图 Product structure drawing 深圳市德威玛通讯设备有限公司 4 4. 产品实物图 Product picture 5.天线性能：（驻波图、增益、效率、方向图） Antenna performance:(standing wave, gain, efficiency, direction diagram) 深圳市德威玛通讯设备有限公司 5 深圳市德威玛通讯设备有限公司 6 深圳市德威玛通讯设备有限公司 7 6.包装方式 manner of packing 包装方式 manner of packing 包装材料 packing material 包装规格 packing size 包装数量 package quantity 备注 remark 包装 pack PE 袋 PE bag 85*120mm1000pcs 焊接处包气泡膜 The welding place is covered with bubble film

Test Model No.: FS‐R11D‐ESC‐BS Radiated Emission Conduct Emission