2A2UNR11P0111-Channel Receiver

FS-R11P-BS 接收机 Receiver Http://www.flysky-cn.com Copyright ©2023 Flysky Technology Co., Ltd. • 产品型号：FS-R11P-BS • 适配发射机：FS-MG11-BS • 适配模型：车、船 • PWM 通道数：11 • 无线频率：2.4GHz ISM • 发射功率：<20dBm • 天线类型：外置单天线（同轴） • 遥控距离： >150 米 ( 空旷无干扰地面距离 ) • 无线协议：2A-BS • 通道分辨率：4096 级 • 数据输出：PWM • 输入电源：3.5 ~ 8.4V/DC • 工作电流：20mA/5V • 在线更新：无 • 温度范围：-10°C ~ +60°C • 湿度范围：20% ~ 95％ • 防水等级：PPX4 • 外形尺寸：35.0mm*23.3mm*13.3mm • 机身重量：8g • 认证：CE，FCC ID: 2A2UNR11P01 FS-R11P-BS 是一款采用 2A-BS 通信协议，提供 11 通 道的双向接收机，外置单天线，输出 PWM 信号，可适 配多种模型车和模型船使用。 FS-R11P-BS based on 2A-BS protocol is a receiver which provides 11-channel and bidirectional transmission, featuring external single antenna and PWM signal output. It can adapted to a variety of model cars or boats. 产品介绍 Introduction 接收机概览 Overview 产品规格 Specifications [1] CH1 通道接口 [2] CH2 通道接口 [3] CH3 通道接口 [4] CH4 通道接口 [5] CH5 通道接口 [6] CH6 通道接口 [7] CH7 通道接口 [8] CH10 通道接口 [9] CH11 通道接口 [10] LED 指示灯 [11] 天线 [12] CH9 通道接口 [13] CH8 通道接口 [14] S ( 通道接口信号端 ) [15] "+" ( 通道接口正极） [16] "- "( 通道接口负极） 对码 Binding [1] CH1 Interface [2] CH2 Interface [3] CH3 Interface [4] CH4 Interface [5] CH5 Interface [6] CH6 Interface [7] CH7 Interface [8] CH10 Interface [9] CH11 Interface [10] LED [11] Antenna [12] CH9 Interface [13] CH8 Interface [14] S(CH Interface Signal Pin) [15] "+"(CH Interface Anode) [16] "-"(CH Interface Cathode) • Product Name: FS-R11P-BS • Adaptive Transmittes: FS-MG11-BS • Adaptive Models: Cars or boats • PWM Channels: 11 • RF: 2.4GHz ISM • Maximum Power: <20dBm (e.i.r.p.) （EU） • Antenna: Single External Antenna • Distance: >150m (Ground Distance without Interference) • 2.4G Protocol: 2A-BS • Resolution: 4096 • Data Output: PWM • Input Power: 3.5 ~ 8.4V/DC • Working Current:20mA/5V • Online Update: None • Temperature Range: -10°C ~ +60°C • Humidity Range: 20% ~ 95% • WaterProof: PPX4 • Dimensions: 35.0mm*23.3mm*13.3mm • Weight: 8g • Certifications: CE, FCC ID: 2A2UNR11P01 本款接收机上电即自动进入对码状态，操作步骤如下： 1. 将发射机进入对码状态（发射机进入对码状态的方式可能不同，请根据发射机的使用说明书进行操作）； 2. 接收机上电等待 1 秒没有连接将自动进入对码； 3. 对码成功后 , 接收机 LED 指示灯常亮 ; 4. 检查发射机、接收机是否正常工作。如需重新对码，请重复以上步骤。 注： 1. 对码时请先将发射机进入对码状态，再将接收机进入对码状态，若 10 秒内对码没有完成，接收机指示灯进入慢闪状态； 2. FS-R11P-BS 接收机采用 2A-BS 协议，只兼容该协议的发射机。 [1] [2] [3] [4] [5] [6] [7] [8][9][10] [11] [12] [13] [15] [16] [14] FS-R11P-BS 接收机 Receiver Http://www.flysky-cn.com Copyright ©2023 Flysky Technology Co., Ltd. 对码 Binding The receiver will automatically enter bind mode matching state upon power-on. The operation steps are as follows: 1. Put the transmitter in bind mode(The transmitter may enter bind mode in different ways, please follow the transmitter's instruction manual). 2. The receiver is powered on and wait 1 second. If there is no connection, the receiver will automatically enter bind mode. 3. The receiver LED will be solid on after the binding process is successful. 4. Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any problems arise. Notes: 1. During the bind mode, put the transmitter in bind mode first, then put the receiver in bind mode, If the binding process is not completed within 10 seconds, the receiver LED goes into a slow flashing state. 2. The FS-R11P-BS receiver complies with the 2A-BS protocol and is only compatible with transmitters conforming to this protocol. 注意事项： • 使用前必须确保本产品与模型安装正确，否则可能导致模型发生严重损坏。 • 关闭时，请务必先关闭接收机电源，然后关闭发射机。如果关闭发射机电源时，接收机仍然在工作，将会导致遥控设备失控。失控保 护设置不合理可能引起事故。 • 确保接收机安装在远离电机或电子噪声过多的区域。 • 接收机天线需远离导电材料，例如金属棒和碳物质。为了避免影响正常工作，请确保接收机天线和导电材料之间至少有1厘米以上的距离。 • 准备过程中，请勿连接接收机电源，避免造成不必要的损失。 失控保护 Failsafe Attentions: • Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury. • Make sure the receiver's battery is disconnected before turning off the transmitter, failure to do so can result out of control. Unreasonable setting of the Failsafe may cause accidents. • Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical noise. • Keep the receiver's antenna at least 1cm away from conductive materials such as carbon or metal. • Do not power on the receiver during the setup process to prevent loss of control. 失控保护功能用于当接收机无法正常收到发射机的信号不受控制时，保护模型和操作人员的安全。 本款接收机默认失控后保持最后输出，若已在发射机端设置，则按照设置值输出。 注：该接收机无论是否在发射端设置，当失控保护功能触发时，CH2 通道油门无输出信号。 The failsafe function is used to protect the model and personnel when the receiver loses its signal and is out of control . By default, the receiver will keep the final output after losing control. If it has been set at the transmitter end, it will output according to the set value. Note: Whether the receiver is set at the transmitting end or not, the CH2 channel throttle has no output signal when the failsafe function is triggered. FS-R11P-BS 接收机 Receiver Http://www.flysky-cn.com Copyright ©2023 Flysky Technology Co., Ltd. 认证相关 Certifications FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the us…

Text truncated - open the document above for the full version.

ShenZhen FLYSKY Technology Co.,Ltd * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2A2UNR11P01 FRN of applicant: 0031248305 Per section 2.911(d)(7) of the FCC rules, ShenZhen FLYSKY Technology Co.,Ltd certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: Baihetian Innovative Solutions FCC Registration Number(FRN): 0033401605 Physical U.S. Company Address: 6837 Chase Rd, Dearborn, MI 48126, USA Contact Person: Kenneth Young Agent Email Address: [email protected] The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Signed: Printed name: Kyle Li Title: RD Manager Company Name: ShenZhen FLYSKY Technology Co.,Ltd Date: 7/6/2023 Agent Signed (if different to Applicant): Signed: Printed name: Kenneth Young Title: Manager Company Name: Baihetian Innovative Solutions Date: 7/6/2023

ShenZhen FLYSKY Technology Co.,Ltd Covered Equipment Certification Attestation Letter 7/6/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2A2UNR11P01 ShenZhen FLYSKY Technology Co.,Ltd certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. ShenZhen FLYSKY Technology Co.,Ltd certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Signed: Printed name: Kyle Li Title: RD Manager Company Name: ShenZhen FLYSKY Technology Co.,Ltd Date: 7/6/2023

DATE : 2023-07-06 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Jason Wu of Global United Technology Services Co., Ltd.and No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with ShenZhen FLYSKY Technology Co.,Ltd and 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China Signature: Name: Kyle Li Title: RD Manager Company: ShenZhen FLYSKY Technology Co.,Ltd

ShenZhen FLYSKY Technology Co.,Ltd DATE : 2023-07-06 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2A2UNR11P01 Product Name: 11-CHANNEL RECEIVER Request for Confidentiality To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Signature: Name: Kyle Li Title: RD Manager

Test Model No.: FS‐R11P‐BS

20230420 0.175磨砂PC+3M467胶 19.6*15.1mm 01 彩色印刷 FS-R11P-BS接收机 FS-R11P-BS接收机贴纸 B-TFSR11PBS-01 Adobe Illustrator CC 2016 李德平 产品经理确认 PANTONE 478 C PANTONE Black 6C White

Test Model No.: FS‐R11P‐BS

FCC ID: 2A2UNR11P01 RF Exposure Evaluation Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3–3.0 614 1.63 *(100) 6 3.0–30 1842/f 4.89/f *(900/f 2 ) 6 30–300 61.4 0.163 1.0 6 300–1500 f/300 6 1500–100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f 2 ) 30 30–300 27.5 0.073 0.2 30 300–1500 f/1500 30 1500–100,000 1.0 30 f = frequency in MHz Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 , Pout = output power to antenna in mW; G = gain of antenna in linear scale, Pi = 3.1416; R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. FCC ID: 2A2UNR11P01 Test Result of RF Exposure Evaluation Channel Output power to antenna (dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm2) Limit (mW/cm2) Result 2440MHz 11.6 14.45 0.0022 1.0 PASS Remark: antenna gain=-1.11dBi

Global United Technology Services Co., Ltd. Report No.: GTS2023060374F01 Authorized Signature: Robinson Luo Laboratory Manager This results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Page 1 of 38 TEST REPORT Applicant: ShenZhen FLYSKY Technology Co.,Ltd Address of Applicant: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China Manufacturer: ShenZhen FLYSKY Technology Co.,Ltd Address of Manufacturer: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China Factory: Dongguan Flysky RC Model technology Co.,Ltd Address of Factory: West building 3, HuangjinyuanInd Park, Qiaoli North Gate, Changping Town, Dongguan, China Equipment Under Test (EUT) Product Name: 11-CHANNEL RECEIVER Model No.: FS-R11P-BS Trade Mark: FLYSKY FCC ID: 2A2UNR11P01 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Date of sample receipt: June 16, 2023 Date of Test: June 16, 2023-July 06, 2023 Date of report issued: July 06, 2023 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No.: GTS2023060374F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 38 2 Version Version No. Date Description 00 July 06, 2023 Original Prepared By: Date: July 06, 2023 Project Engineer Check By: Date: July 06, 2023 Reviewer Report No.: GTS2023060374F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 38 3 Contents Page 1 COVER PAGE ................................................................................................................................................ 1 2 VERSION ........................................................................................................................................................ 2 3 CONTENTS .................................................................................................................................................... 3 4 TEST SUMMARY ........................................................................................................................................... 4 4.1 MEASUREMENT UNCERTAINTY .................................................................................................................. 4 5 GENERAL INFORMATION ............................................................................................................................ 5 5.1 GENERAL DESCRIPTION OF EUT ............................................................................................................... 5 5.2 TEST MODE .............................................................................................................................................. 7 5.3 TEST FACILITY .......................................................................................................................................... 7 5.4 TEST LOCATION ....................................................................................................................................... 7 5.5 DESCRIPTION OF SUPPORT UNITS ............................................................................................................. 7 5.6 DEVIATION FROM STANDARDS ................................................................................................................... 7 5.7 ABNORMALITIES FROM STANDARD CONDITIONS ......................................................................................... 7 5.8 ADDITIONAL INSTRUCTIONS ....................................................................................................................... 7 6 TEST INSTRUMENTS LIST ........................................................................................................................... 8 7 TEST RESULTS AND MEASUREMENT DATA .......................................................................................... 10 7.1 ANTENNA REQUIREMENT ......................................................................................................................... 10 7.2 CONDUCTED EMISSIONS ......................................................................................................................... 11 7.3 CONDUCTED PEAK OUTPUT POWER ........................................................................................................ 14 7.4 20DB EMISSION BANDWIDTH .................................................................................................................. 15 7.5 CARRIER FREQUENCIES SEPARATION ...................................................................................................... 16 7.6 HOPPING CHANNEL NUMBER .................................................................................................................. 17 7.7 DWELL TIME ........................................................................................................................................... 18 7.8 SPURIOUS EMISSION IN NON-RESTRICTED & RESTRICTED BANDS ............................................................. 19 7.8.1 Conducted Emission Method ........................................................................................................... 19 7.8.2 Radiated Emission Method .............................................................................................................. 20 8 TEST SETUP PHOTO ...............................…

Text truncated - open the document above for the full version.

Report No.: GTS2023060374F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 1 of 10 AppendixA: 20dB Emission Bandwidth Test Result Test Mode Antenna Frequency[MHz] 20db EBW[MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict Tx Ant1 2408 0.534 2407.721 2408.255 --- --- Tx Ant1 2440 0.510 2439.739 2440.249 --- --- Tx Ant1 2475 0.534 2474.727 2475.261 --- --- Test Graphs Tx-Ant1-2408 Tx-Ant1-2440 / Tx-Ant1-2475 / Report No.: GTS2023060374F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 10 AppendixB: Occupied Channel Bandwidth Test Result Test Mode Antenna Frequency[MHz] OCB [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict Tx Ant1 2408 0.52959 2407.7184 2408.2480 --- --- Tx Ant1 2440 0.52031 2439.7318 2440.2521 --- --- Tx Ant1 2475 0.52296 2474.7276 2475.2505 --- --- Test Graphs Tx-Ant1-2408 Tx-Ant1-2440 / Tx-Ant1-2475 / Report No.: GTS2023060374F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 10 AppendixC: Maximum conducted output power Test Result Test Mode Antenna Frequency[MHz] Result[dBm] Limit[dBm] Verdict Tx Ant1 2408 10.96 ≤20.97 PASS Tx Ant1 2440 11.60 ≤20.97 PASS Tx Ant1 2475 11.18 ≤20.97 PASS Test Graphs Tx-Ant1-2408 Tx-Ant1-2440 / Tx-Ant1-2475 / Report No.: GTS2023060374F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 4 of 10 AppendixD: Carrier frequency separation Test Result Test Mode Antenna Frequency[MHz] Result[MHz] Limit[MHz] Verdict Tx Ant1 Hop_2408 2.52 ≥0.534 PASS Tx Ant1 Hop_2422.5 2.00 ≥0.534 PASS Tx Ant1 Hop_2475 1.98 ≥0.534 PASS Test Graphs Tx-Ant1-Hop-2408 Tx-Ant1-Hop-2422.5 / Tx-Ant1-Hop-2475 / Report No.: GTS2023060374F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 5 of 10 AppendixE: Time of occupancy Test Result Test Mode Antenna Frequency[MHz] BurstWidth [ms] Observation Period[s] TotalHops [Num] Result[s] Limit[s] Verdict Tx Ant1 Hop_2408 0.770 6.4 9 0.0069 ≤0.4 PASS Test Graphs Tx-Ant1-Hop-2408 Tx-Ant1-Hop-2408 Report No.: GTS2023060374F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 6 of 10 AppendixF: Number of hopping channels Test Result Test Mode Antenna Frequency[MHz] Result[Num] Limit[Num] Verdict Tx Ant1 Hop 16 ≥15 PASS Test Graphs / Tx-Ant1-Hop / Report No.: GTS2023060374F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 7 of 10 AppendixG:Band edge measurements Test Result Test Mode Antenna ChName Frequency[MHz] RefLevel [dBm] Result [dBm] Limit [dBm] Verdict Tx Ant1 Low 2408 10.86 -38.97 ≤-9.14 PASS Tx Ant1 High 2475 11.07 -43.09 ≤-8.94 PASS Tx Ant1 Low Hop_2408 9.59 -48.60 ≤-10.41 PASS Tx Ant1 High Hop_2475 9.92 -51.23 ≤-10.08 PASS Test Graphs Tx-Ant1-2408 Tx-Ant1-2475 Tx-Ant1-Hop_2408 Tx-Ant1-Hop_2475 Report No.: GTS2023060374F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 8 of 10 AppendixH:Conducted Spurious Emission Test Result Test Mode Antenna Frequency[MHz] FreqRange [MHz] RefLevel [dBm] Result [dBm] Limit [dBm] Verdict Tx Ant1 2440 0~Reference 11.60 11.60 --- PASS Tx Ant1 2440 30~1000 11.60 -50.91 ≤-8.4 PASS Tx Ant1 2440 1000~26500 11.60 -33.93 ≤-8.4 PASS Tx Ant1 2408 0~Reference 10.88 10.88 --- PASS Tx Ant1 2408 30~1000 10.88 -50.98 ≤-9.12 PASS Tx Ant1 2408 1000~26500 10.88 -39.31 ≤-9.12 PASS Tx Ant1 2475 0~Reference 11.08 11.08 --- PASS Tx Ant1 2475 30~1000 11.08 -51.07 ≤-8.92 PASS Tx Ant1 2475 1000~26500 11.08 -38.22 ≤-8.92 PASS Report No.: GTS2023060374F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 9 of 10 Test Graphs Tx-Ant1-2440-0~Reference Tx-Ant1-2440-30~1000 Tx-Ant1-2440-1000~26500 Tx-Ant1-2408-0~Reference Tx-Ant1-2408-30~1000 Tx-Ant1-2408-1000~26500 Report No.: GTS2023060374F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 10 of 10 Tx-Ant1-2475-0~Reference Tx-Ant1-2475-30~1000 / Tx-Ant1-2475-1000~26500 / ---End---

深圳市德威玛通讯设备有限公司 2 1.目的 objective 对于深圳市德威玛通讯设备有限公司出品的移动通信终端天线产品规格、测试方法 进行规范，避免因测试条件，方法的不同引起误差。 To standardize the product specifications and test methods of mobile communication terminal antenna produced by Shenzhen Devima Communication Equipment Co., LTD., to avoid errors caused by different test conditions and methods. 2.技术指标与实验设备technical index 2.1 技术指标technical index 产品电气性能指标 Electrical performance index of products 工作频率范围 operating frequency range 2400~2500MHz 驻波比 SWR 2400~2500MHz<5.0 天线增益 antenna gain 2400~2500MHz:-1.11dBi 辐射效率 radiant efficiency 2400~2500MHz>15% 阻抗 impedance 50ohm 产品材料说明 Product material Description 灰色1.13 同轴线100mm Gray 1.13 coaxial line 100mm 产品环境说明 Product Environment Description 工作温度 Operation Temperature - 30 ̊C ~ + 85 ̊C 储藏温度 Store Temperature - 30 ̊C ~ + 85 ̊C 深圳市德威玛通讯设备有限公司 3 3. 产品结构图 Product structure drawing 深圳市德威玛通讯设备有限公司 4 4. 产品实物图 Product picture 5.天线性能：（驻波图、增益、效率、方向图） Antenna performance:(standing wave, gain, efficiency, direction diagram) 深圳市德威玛通讯设备有限公司 5 深圳市德威玛通讯设备有限公司 6 深圳市德威玛通讯设备有限公司 7 6.包装方式 manner of packing 包装方式 manner of packing 包装材料 packing material 包装规格 packing size 包装数量 package quantity 备注 remark 包装 pack PE 袋 PE bag 85*120mm1000pcs 焊接处包气泡膜 The welding place is covered with bubble film

Test Model No.: FS‐R11P‐BS Radiated Emission Conduct Emission