2A337-BOXER-ELRSBOXER

WWW.RADIOMASTERRC.COM Quick start guide Boxer Introduction Thank you for purchasing the RadioMaster Boxer 2.4g remote control system. The system is versatile and can be used by beginners and professionals. In order to ensure the correct and safe use of this product, please read this manual carefully before use. Due to constant improvements in software and hardware this manual may change over time. The information contained in this manual is subject to change without notice. Visit our website for the most up to date information. Boxer remote control is suitable for all types of fixed-wing aircraft, gliders, helicopters, cars, boats, robotics, multi-rotor aircraft and anything else you might create, if you can build it RadioMaster can control it. The Boxer uses a powerful operating system called EdgeTX, for more information visit the links below. -The RadioMaster team. Many remote-control models are equipped with powerful motors and sharp propellers. When using or maintaining models, proceed with caution. When performing assembly or maintenance, make sure to disconnect the power to the model and remove the propellers. Do not operate the Boxer remote control system under the following conditions: • In severe weather or strong windy conditions, such as rain, hail, snow, storms or electromagnetic environ- ments. • In any situation where visibility is limited. • In areas where people, property, high-voltage power lines, public roads, vehicles or animals may be present. • If you feel tired or unwell, or under the influence of drugs or alcohol. • If the remote control or model seems to be damaged or not working properly. • In areas with high 2.4GHz interference or where 2.4GHz radio is prohibited. • When the radios battery voltage is too low to be used. • In areas where local regulations prohibit the use of aviation models. Safety Information Manual and firmware download Boxer is pre-installed with factory approved EdgeTX firmware. To download the latest software manual, please visit the RadioMaster website: https://www.radiomasterrc.com To download the latest firmware for your Boxer remote control, please visit the EdgeTX website: https://www.Edge-tx.org Important ANTENNA: Install the provided antenna in the top of the radio BEFORE installing batteries and turning on the radio. DO NOT operate the radio without the antenna installed and the internal RF module powered on. Doing so will damage the internal RF module and will not be covered under warranty. FIRMWARE: The Boxer is pre-installed with the most stable firmware at the factory at time of release. please only attempt to update the firmware if you are confident in the process. Incorrect firmware updates may cause the remote control to become inoperable. 1 Remote control overview Batteries and charging 2 Boxer has a built-in USB-C charging function for 3.7V lithium batteries. The charging circuit is only designed to charge 2x 3.7V Li-ion 18650 or 2x 3.7V Li-Poly batteries (2s 7.4v Lipo battery pack), the nominal battery voltage is 3.7V, the charged voltage is 4.2V/Cell. Do not use LiFE battery packs or 18650 lithium-ion batteries with a nominal voltage of 3.6v with a fully charged voltage of 4.10V. Charging the incorrect type of battery may damage the charger or cause a fire. If using Li-ion, ensure the cells are not protected and are button-top cells. Please check the voltage and condition of the battery regularly and never charge unattended. Always charge in a safe area away from combustible materials. Refrain from charging if the remote control gets wet or damaged in any way. Do not charge with the polarity reversed RadioMaster does not assume any responsibility for any adverse consequences caused by the use or misuse of this product. Antenna Type-C Data Port 6 Pos Buttons Trainer Port LCD Screen Headphone Jack SF Momentary switch S1 DialS2 Dial SE Latching switch SB 3 Position SA 2 PositionSD 2 Position SC 3 Position Speaker Right Gimbal Left Gimbal Power Button Lanyard Loop MDL Button SYS Button RTN Button PAGE> Button PAGE< Button TELE Button Scroll wheel TYPE-C Charger Port Trim Buttons Model and protocol selection (multi-protocol module) Notes 3 Model selection and protocol selection (ELRS version) The Boxer comes with 4in1 or CC2500 multi-protocol internal RF module, which is compatible with several different protocols. To view the latest list of all compatible protocols, please visit https://www.- multi-module.org/ Please note that new protocols will be constantly updated and added to the latest firmware. Some new protocols may require firmware upgrades. Boxer ELRS units are equipped with an internal ELRS module, capable of providing 25mW-1000mW RF output. In non-extreme circumstances, 100mW output at 500Hz update rate is recommended, as higher RF output and update rates may significantly reduce battery life and generate excessive heat. Bind instructions 1Turn off the transmitter 2Cycle power to the receiver 3 times, the receiver LED will flash twice- indicating bind mode. 3Turn on the transmitter, long press the SYS button and choose the ExpressLRS LUA under the TOOLS menu. Scroll down to [Bind] and press enter. 4The LED on the receiver should now be solid, indicating successful bind. • Long press the MDL button to enter the model settings, select MULTI in the SETUP page, and select the protocol to be used in the sub-options. The system will automatically turn on the corresponding RF module according to the RF protocol you selected. • Bind [BND] is used to start the binding process. • Range [RNG] button can reduce the power to 1/30 to facilitate testing of remote-control distance. EdgeTX software is very powerful, and has a large number of programming and mixing functions. Please download the comprehensive software installation guide from the link below for more detailed instructions: https://www.Edge-tx.org or https://www.radiomasterrc.com 4 Specifications Size: 235*178*77mm Weight: 532.5g Frequency: 2.400GHz-2.480GHz Internal RF…

Text truncated - open the document above for the full version.

ShenzhenRadiomasterTechnologyCo.,Ltd 2.911(d)(5)(ii)ApplicantAttestationv1.2 Section2.911(d)(5)(ii)Certification–Applicant(CoveredList) Companyname:ShenzhenRadiomasterTechnologyCo.,Ltd Address:4FYangTianBuilding,Area72XingDongcommunity,XinAnStreet,BaoAndistrict,Shen Zhencity,GuangdongProvince,China ProductName:BOXER FCCID:2A337-BOXER-ELRS Model(s):BOXERELRS,BOXERELRSMAX,BOXERELRSMAXPRO,BOXERCC2500,BOXERSE, BOXERELRSPRO,BOXERELRSLITE,BOXERMAX,BOXERMAXPRO 2.911(d)(5)(ii)Applicantfiling We,[ShenzhenRadiomasterTechnologyCo.,Ltd]certifythat,asofthedateofthefilingofthe application,theapplicantisnotidentified NOTE1 onthe“CoveredList” NOTE2 ,establishedpursuantto §1.50002ofthischapter,asanentityproducingcoveredcommunicationsequipment. Yourssincerely, Name:OwenLeeDate:2023-04-03 TitleandCompanyname:generalmanager/ShenzhenRadiomasterTechnologyCo.,Ltd NOTE1 Deleteoptionnotapplicabletothisapplication. NOTE2 “CoveredList ” ;istheListofEquipmentandServicesCoveredBySection2ofTheSecureNetworksAct,availableat https://www.fcc.gov/supplychain/coveredlist References; 1)986446D01CoveredEquipmentv01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2)FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

ShenzhenRadiomasterTechnologyCo.,Ltd 2.911(d)(5)(i)EquipmentTypeAttestationv1.2 Section2.911(d)(5)(i)Certification–EquipmentType Companyname:ShenzhenRadiomasterTechnologyCo.,Ltd Address:4FYangTianBuilding,Area72XingDongcommunity,XinAnStreet,BaoAndistrict,Shen Zhencity,GuangdongProvince,China ProductName:BOXER FCCID:2A337-BOXER-ELRS Model(s):BOXERELRS,BOXERELRSMAX,BOXERELRSMAXPRO,BOXERCC2500,BOXERSE, BOXERELRSPRO,BOXERELRSLITE,BOXERMAX,BOXERMAXPRO 2.911(d)(5)(i)EquipmentType We,[ShenzhenRadiomasterTechnologyCo.,Ltd]certifythattheequipmentforwhichauthorization issoughtthroughcertificationisnot: Prohibitedfromreceivinganequipmentauthorizationpursuantto§2.903;oftheFCCrules. Identifiedasanequipmenttypeinthe“CoveredList” NOTE1 Yourssincerely, Name:OwenLeeDate:2023-04-03 TitleandCompanyname:generalmanager/ShenzhenRadiomasterTechnologyCo.,Ltd NOTE1 “CoveredList ” ;istheListofEquipmentandServicesCoveredBySection2ofTheSecureNetworksAct,availableat https://www.fcc.gov/supplychain/coveredlist References; 1)986446D01CoveredEquipmentv01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2)FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

ShenzhenRadiomasterTechnologyCo.,Ltd 2.911(d)(7)USAAgentv1.2 Section2.911(d)(7)USAAgentforServiceofProcess Companyname:ShenzhenRadiomasterTechnologyCo.,Ltd Address:4FYangTianBuilding,Area72XingDongcommunityXinAnStreet,BaoAn district,ShenZhencity,GuangdongProvince,China ProductName:BOXER FCCID:2A337-BOXER-ELRS Model(s):BOXERELRS,BOXERELRSMAX,BOXERELRSMAXPRO,BOXER CC2500,BOXERSE,BOXERELRSPRO,BOXERELRSLITE,BOXERMAX, BOXERMAXPRO 2.911(d)(7)USADesignatedAgentforServiceofProcess We,[ShenzhenRadiomasterTechnologyCo.,Ltd](“theapplicant”)designate[SUN BEYONDCONSULTYINGLTD] NOTE1 forthepurposeofacceptingserviceofprocess onbehalfoftheapplicant. Applicantconsent:WeAcknowledgeourconsenttoacceptserviceofprocessinthe UnitedStatesformattersrelatedtotheapplicableequipment,andatthephysicalU.S. addressandemailaddressofthedesignatedagentandacknowledgeour acceptanceofourobligationtomaintainanagentforserviceofprocessintheUnited Statesfornolessthanoneyearaftereitherthegranteehaspermanentlyterminated allmarketingandimportationoftheapplicableequipmentwithintheU.S.,orthe conclusionofanyCommission-relatedadministrativeorjudicialproceedinginvolving theequipment,whicheverislater. Agentobligation:WeAcknowledgeourobligationtoacceptserviceofprocessinthe UnitedStatesformattersrelatedtotheapplicableequipmentatourphysicalU.S. addressandemailaddressfornolessthanoneyearaftereitherthegranteehas permanentlyterminatedallmarketingandimportationoftheapplicableequipment withintheU.S.,ortheconclusionofanyCommission-relatedadministrativeorjudicial proceedinginvolvingtheequipment,whicheverislater. USAAgentApplicant Companyname:SUNBEYOND CONSULTYINGLTD Companyname:ShenzhenRadiomaster TechnologyCo.,Ltd Address:OFFICENO.448,4THFLOOR,90 CANALSTREET, BOSTON,MASSACHUSETTS,USA Address:4FYangTianBuilding,Area72 XingDongcommunityXinAnStreet,Bao Andistrict,ShenZhencity,Guangdong Province,China FRN:0033598426FCCIDNumber:2A337-BOXER-ELRS ContactName:WenchaoXiangContactName:OwenLee ShenzhenRadiomasterTechnologyCo.,Ltd 2.911(d)(7)USAAgentv1.2 TelephoneNo:+1(508)4700660TelephoneNo:18601573500 Email:[email protected]:[email protected] Signature: Title:generalmanager Date:2023-04-10Date:2023-04-10 NOTE1:AnapplicantlocatedintheUnitedStatesmaydesignateitselfastheagentforservice ofprocess. Reference;FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-nation al-security-threats-to-the-communications-supply-chain-through-the

ShenzhenRadiomasterTechnologyCo.,Ltd AgentAuthorization Company:ShenzhenRadiomasterTechnologyCo.,Ltd Address:4FYangtianBuilding,Xin'anStreet,Bao'anDistrict,Shenzhen, Guangdong,China ProductName:BOXER ModelNumber(s):BOXERELRS,BOXERELRSMAX,BOXERELRSMAXPRO,BOXER CC2500,BOXERSE,BOXERELRSPRO,BOXERELRSLITE,BOXERMAX,BOXER MAXPRO ProductDescription:BOXER WeauthorizeMiCOMLabsInc.,575BoulderCourt,Pleasanton,California94566,USA, toactonourbehalfonallmattersconcerningthecertificationofabovenamed equipment. WedeclarethatMiCOMLabsInc.isallowedtoforwardallinformationrelatedtothe approvalandcertificationofequipmenttotheregulatoryagenciesasrequiredandto discussanyissuesconcerningtheapprovalapplication.Anyandallactscarriedoutby MiCOMLabsonourbehalfshallhavethesameeffectasactsofourown. Signature:Date:2023-04-03 Name:OwenLee Title:GeneralManager Company:ShenzhenRadiomasterTechnologyCo.,Ltd

ShenzhenRadiomasterTechnologyCo.,Ltd DeclarationonModelDifferences We, ShenzhenRadiomasterTechnologyCo.,Ltd 4FYangTianBuilding,Area72XingDongcommunity,XinAnStreet,BaoAndistrict, ShenZhencity,GuangdongProvince,China Declarethatthefollowingproduct(s): FCCID:2A337-BOXER-ELRS ProductName:BOXER ModelNo.:BOXERELRS,BOXERELRSMAX,BOXERELRSMAXPRO,BOXERCC2500, BOXERSE,BOXERELRSPRO,BOXERELRSLITE,BOXERMAX,BOXERMAXPRO Utilizetheidenticalcircuitdesign,PCBlayout,shieldingandinterfacewith(BOXERELRS), onlythemodelnamedifferent.Thereforethisapplicationcanberegardedasidenticalin performancetothesubmittedtestsample. Themanufacturerwouldtakealltheresponsibilitiesfortheaboveproduct(s). Forandonbehalfof Authorizedperson Name:OwenLee Position:generalmanager Dateofissue:2023-04-10 *IherebydeclarethatIamentitledtosignonbehalfoftheapplicantandthattheinformationsuppliediscorrectandcomplete.

ShenzhenRadiomasterTechnologyCo.,Ltd OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USA Date:2023-04-03 Subject;RequestforConfidentiality FCCID:2A337-BOXER-ELRS ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,we arerequestingtheCommissiontowithholdthefollowingattachment(s)asconfidential documentsfrompublicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredas proprietaryinformationinoperationoftheequipment.Thepublicdisclosureofthesedocuments mightbeharmfultoourcompanyandwouldgivecompetitorsanunfairadvantageinthemarket. SchematicDiagram BlockDiagram OperationalDescription SWSECURITYDESCRIPTION PartsList Tuneup Inadditionaltoabovementioneddocuments,inordertocomplywiththemarketingregulations inTitle47CFR§2.803andtheimportationrulesinTitle47CFR§2.1204,whileensuringthat businesssensitiveinformationremainsconfidentialuntiltheactualmarketingofnewly authorizeddevices,werequestShortTermConfidentialityofthefollowingattachment(s); ExternalPhotos TestSetupPhotos InternalPhotos UserManual For45days,pursuanttoPublicNoticeDA04-1705. OR For180dayspursuanttoKDB726920D01. Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondenceduringthecertificationreviewprocesscannotbegrantedasconfidential documentsandthisinformationwillbeavailableforpublicreviewoncethegrantofequipment authorizationisissued. Sincerely, Signature: Name:OwenLee Title:generalmanager

Code:AB-RF-05-b ExternalPhotograph Code:AB-RF-05-b Code:AB-RF-05-b Code:AB-RF-05-b

Model: BOXER 6.6-8.4V FCC-ID 2A337-BOXER-ELRS Shenzhen Radiomaster Co. LTD Made in China 37.5*11.5mm Boxer认证贴纸

Code:AB-RF-05-b InternalPhotograph 2.4GANT Code:AB-RF-05-b Code:AB-RF-05-b Code:AB-RF-05-b WIFIANTBTANT Code:AB-RF-05-b Code:AB-RF-05-b

Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 1 of 71 FCC SAR Test Report Client Name: Shenzhen Radiomaster Technology Co.,Ltd Address: 4F Yang Tian Building, Area 72 Xing Dong community Xin An Street, Bao An district, Shen Zhen city, Guangdong Province, China Product Name: BOXER Date: Apr. 03, 2023 Shenzhen Anbotek Compliance Laboratory Limited Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 2 of 71 Contents 1. Statement of Compliance ................................................................................................6 2. General Information ........................................................................................................ 7 2.1Client Information ............................................................................................................................................... 7 2.2Description of Equipment Under Test (EUT) ...................................................................................................... 7 2.3Device Category and SAR Limits .......................................................................................................................9 2.4Applied Standard ................................................................................................................................................9 2.5Environment of Test Site .................................................................................................................................... 9 2.6Test Configuration .............................................................................................................................................. 9 3. Specific Absorption Rate (SAR) ....................................................................................10 3.1Introduction ...................................................................................................................................................... 10 3.2SAR Definition ..................................................................................................................................................10 4. SAR Measurement System ...........................................................................................11 4.1E-Field Probe ................................................................................................................................................... 12 4.2Data Acquisition Electronics (DAE) .................................................................................................................. 12 4.3Robot ................................................................................................................................................................13 4.4Measurement Server ........................................................................................................................................14 4.5Phantom ...........................................................................................................................................................14 4.6Device Holder ...................................................................................................................................................16 4.7Data Storage and Evaluation ........................................................................................................................... 17 5. Test Equipment List ...................................................................................................... 19 6. Tissue Simulating Liquids ............................................................................................. 20 7. System Verification Procedures ....................................................................................22 8. EUT Testing Position.................................................................................................... 24 8.1.Body Worn Position ..........................................................................................................................................24 9. Measurement Procedures .............................................................................................25 9.1Spatial Peak SAR Evaluation ...........................................................................................................................25 9.2Power Reference Measurement ...................................................................................................................... 26 9.3Area Scan Procedures ..................................................................................................................................... 26 9.4Zoom Scan Procedures ................................................................................................................................... 27 9.5Volume Scan Procedures .................................................................................................................................28 9.6Power Drift Monitoring ......................................................................................................................................28 10. Conducted Power ......................................................................................................... 29 11. Antenna Location .......................................................................................................... 31 12. SAR Test Results Summary ......................................................................................... 32 13. Simultaneous Transmission Analysis ........................................................................... 34 Simultaneous TX SAR Considerations ........................................................................................................................ 34 Evaluation of Simultaneous SAR .................................................................................................................................35 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPag…

Text truncated - open the document above for the full version.

Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 46 of 71 Appendix D. DASY System Calibration Certificate Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 47 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 48 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 49 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 50 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 51 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 52 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 53 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 54 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 55 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 56 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 57 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 58 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 59 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 60 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 61 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 62 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 63 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 64 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 65 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 66 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 67 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 68 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 69 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 70 of 71 Report No.: 18220WC20268401FCC ID: 2A337-BOXER-ELRSPage 71 of 71 *****END OF REPORT*****

ReportNo.:18220WC20268202FCCID:2A337-BOXER-ELRSPage1of32 Code:AB-RF-05-b FCCTestReport ClientName:ShenzhenRadiomasterTechnologyCo.,Ltd ClientAddress: 4FYangTianBuilding,Area72XingDong communityXinAnStreet,BaoAndistrict, ShenZhencity,GuangdongProvince,China ProductName:BOXER ReportDate:Apr.03,2023 ShenzhenAnbotekComplianceLaboratoryLimited ReportNo.:18220WC20268202FCCID:2A337-BOXER-ELRSPage2of32 Code:AB-RF-05-b Contents 1.GeneralInformation...........................................................................................................................................6 1.1.ClientInformation....................................................................................................................................6 1.2.DescriptionofDevice(EUT)..................................................................................................................6 1.3.AuxiliaryEquipmentUsedDuringTest................................................................................................7 1.4.DescriptionofTestConfiguration.........................................................................................................7 1.5.DescriptionofTestSetup.......................................................................................................................8 1.6.TestEquipmentList.................................................................................................................................9 1.7.MeasurementUncertainty...................................................................................................................10 1.8.DescriptionofTestFacility...................................................................................................................10 2.SummaryofTestResults................................................................................................................................11 3.ConductedEmissionTest................................................................................................................................12 3.1.TestStandardandLimit.......................................................................................................................12 3.2.TestSetup...............................................................................................................................................12 3.3.TestProcedure.......................................................................................................................................12 3.4.TestData.................................................................................................................................................12 4.RadiationSpuriousEmissionandBandEdge............................................................................................15 4.1.TestStandardandLimit.......................................................................................................................15 4.2.TestSetup...............................................................................................................................................15 4.3.TestProcedure.......................................................................................................................................16 4.4.TestData.................................................................................................................................................17 5.MaximumPeakOutputPowerTest...............................................................................................................27 5.1.TestStandardandLimit.......................................................................................................................27 5.2.TestSetup...............................................................................................................................................27 5.3.TestProcedure.......................................................................................................................................27 5.4.TestData.................................................................................................................................................27 6.6DBOccupyBandwidthTest..........................................................................................................................28 6.1.TestStandardandLimit.......................................................................................................................28 6.2.TestSetup...............................................................................................................................................28 6.3.TestProcedure.......................................................................................................................................28 6.4.TestData.................................................................................................................................................28 7.PowerSpectralDensityTest...........................................................................................................................29 7.1.TestStandardandLimit.......................................................................................................................29 7.2.TestSetup...............................................................................................................................................29 7.3.TestProcedure.......................................................................................................................................29 7.4.TestData.................................................................................................................................................29 8.100kHzBandwidthofFrequencyBandEdgeRequirement.....................................................................30 8.1.TestStandardandLimit.......................................................................................................................30 8.2.…

Text truncated - open the document above for the full version.

Page1of54 AppendixTestData ReportNo.:18220WC20268202TestSampleNo.:1-2-2 StartTestDate:2022.12.14FinishTestDate:2022.12.20 TestEngineer:Auditor: Temperature:24.2°CRelativeHumidity:40% Pressure:1012hPa AppendixA:DTSBandwidth TestResult TestModeAntennaFrequency[MHz] DTSBW [MHz] FL[MHz]FH[MHz]Limit[MHz]Verdict 11BAnt1 24129.0402407.5202416.560≥0.5PASS 24379.0802432.4402441.520≥0.5PASS 24629.0802457.4802466.560≥0.5PASS 11GAnt1 241216.3602403.8402420.200≥0.5PASS 243716.3602428.8002445.160≥0.5PASS 246216.3602453.8002470.160≥0.5PASS 11N20Ant1 241217.6402403.2002420.840≥0.5PASS 243717.5602428.2402445.800≥0.5PASS 246217.6002453.2002470.800≥0.5PASS 11N40Ant1 242235.5802404.2402439.820≥0.5PASS 243735.9402418.8802454.820≥0.5PASS 245236.0002433.8802469.880≥0.5PASS Page2of54 TestGraphs 11B_Ant1_2412 11B_Ant1_2437 11B_Ant1_2462 Page3of54 11G_Ant1_2412 11G_Ant1_2437 Page4of54 11G_Ant1_2462 11N20_Ant1_2412 Page5of54 11N20_Ant1_2437 11N20_Ant1_2462 Page6of54 11N40_Ant1_2422 11N40_Ant1_2437 Page7of54 11N40_Ant1_2452 Page8of54 AppendixB:OccupiedChannelBandwidth TestResult TestModeAntenna Channel Frequency[MHz] OCB [MHz] FL[MHz]FH[MHz]Limit[MHz]Verdict 11BAnt1 241212.3222405.92282418.2448------ 243712.3382430.84522443.1832------ 246212.4362455.74652468.1825------ 11GAnt1 241217.0642403.53152420.5955------ 243717.0342428.47242445.5064------ 246217.0962453.39512470.4911------ 11N20Ant1 241217.9492403.08092421.0299----…

Text truncated - open the document above for the full version.