2A3V8SG25SG25 Sheep/Goat Collar

6/29/23, 2:33 PMFCC USA Compliance Statement - Master User Guide - 2023 https://www.manula.com/manuals/nofence-as/master-user-guide/1/en/topic/fcc-usa-compliance-statement1/1 FCC USA Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Nofence has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Contains FCC ID: XPYUBX20VA01, ISED ID: 8595A-UBX20VA01 with an integrated antenna. This product emits radio frequency energy, but the radiated output power of this device is far below the FCC radio frequency exposure limits. This equipment complies with FCC RF radiation exposure limits for an uncontrolled environment. Nevertheless, the device should be used in such a manner that the potential for human contact with the antenna during normal operation is minimized. In order to comply with FCC RF Exposure requirements, this device must be installed to provide at least 20 cm separation from the human body at all times. Contact usISED Canada Compliance Statement

PRODUCTSHEET-SG25COLLAR Nofencecollarforsheepandgoat ElectricalSpecification Inputvoltage:3,4V-4,2V Peakpowerconsumption:1,5A Audiowarninglevel:82dB@1m Electricpulselevel:0,1J@3kVDuration=0,25sec Solarchargingmaxpeakpower:1385,3mW Communicationinterface Bluetooth™ LTECat-M1and2G GNSSReceiver-GlonassandGPS Environmental IngressProtection:IP67(@0,25mdepthin0,5hrs) Temperaturerange:-25to+55ºC(Operatingandstorage) Physical Dimension(box):84,8x90,5x109,0mm Weightcollarunit296g Weightbattery192g Weightneckstrap21g Totalweight,carriedbyanimal:509g SeeNofenceusermanualforinstructionsontheuseandmaintenanceofthisproduct.

COMPANY LETTERHEAD Covered Equipment Certification Attestation Letter DATE May 9 th 2023 Nemko North America, Inc. 303 River Road Ottawa K1V 1H2 Canada ATTN.: Reviewing Engineer FCC ID: 2A3V8SG25 Nofence AS certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. Nofence AS certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Signed: Printed name: Steinar Fagerli Title: Production Manager Company Name: Nofence AS Date: 6/26/2023

COMPANY LETTERHEAD * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter June 26, 2023 Nemko North America, Inc. 303 River Road Ottawa K1V 1H2 Canada ATTN.: Reviewing Engineer FCC ID: 2A3V8SG25 Per section 2.911(d)(7) of the FCC rules, Nofence AS (“the applicant”) certifies that the equipment for which authorization is sought is designated to the following U.S. Designated agent* for service of process: Company Name: Nofence Inc. Physical U.S. Company Address: 345 West Washington Ave, Suite #408, Madison, Wisconsin 53703 Agent name: Allysse Sorensen Agent Email Address: [email protected] FRN: 0033752312 The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Designated Agent Signed: (Required, if different to Applicant): Signed: Signed: Printed name: Steinar Fagerli Printed name: Allysse Sorensen Title: Production Manager Title: Sales Company Name: Nofence AS Company Name: Nofence AS Date: June 6, 2023 Date: May 9, 2023

Nofence AS Evjevegen 8 6631 Batnfjordsøra Norway 16. March 2023 Nemko North America, Inc. 303 River Road Ottawa, Ontario, Canada K1V 1H2 AUTHORITY TO ACT AS AGENT - FCC On our behalf, I appoint Nemko , to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in FCC regulations will have affixed to it a label identical to that submitted for approval with this application. In signing this letter, Applicant certifies that neither the applicant nor any party to the application is not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. § 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko North America Inc., still resides still resides with us. Sincerely, Printed name: Steinar Fagerli

16. March 2023 Nemko North America, Inc. 303 River Road Ottawa, Ontario, Canada K1V 1H2 REQUEST FOR CONFIDENTIALITY - FCC FCC ID: 2A3V8SG25 Pursuant to Sections 0.457(d) and 0.459 of the Commission’s Rules and FCC Guidance document 726920 , we hereby request permanent confidential treatment of exhibits identified as such in the table below and request they are permanently withheld from public review based on the documents containing trade secrets and proprietary information not customarily released to the public. The public disclosure of this information might be harmful to the applicant and provide unjustified benefits to its competitors. We also request short-term confidentiality on certain exhibits until the intended date of marketing as outlined below. We request the exhibits be withheld from public view for a period of insert number of days (cannot exceed 180 days) days. We attest marketing of the product will only commence after the period of short-term confidentiality expires, or if marketing is to commence before the requested number of days listed above, the grantee will inform Nemko to release the Short-Term Confidentiality information withheld on the FCC equipment authorization website. Exhibit Type of Confidentiality Requested Block Diagrams ☒ Permanent ☐ Short Term External Photos ------------------ ☐ Short Term Internal Photos ☐ Permanent* ☐ Short Term Operation Description ☒ Permanent ☐ Short Term Parts List & Placement/BOM ☒ Permanent ☐ Short Term Tune-Up Procedure ☐ Permanent ☐ Short Term Schematic Diagrams ☒ Permanent ☐ Short Term Test Setup Photos ------------------ ☐ Short Term User’s Manual ☐ Permanent* ☐ Short Term The asterisked items (*) require further information to be provided in this justification letter before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 D01 found at: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. Note: any documents held under the Short-Term confidentiality will automatically become public after the requested time if an appropriate extension request has not been received. Any exhibits (i.e., schematic diagrams) that may have already been requested to have “Permanent” confidentiality as shown above need not be repeated under Short-Term confidentiality request. Sincerely, Signed : Printed name: Steinar Fagerli Title: Production Manager Company Name: Nofence AS

31 August 2023 Nemko North America, Inc. 303 River Road Ottawa, Ontario, Canada K1V 1H2 ANTENNA – FCC JUSTIFICATION STATEMENT FCC ID: 2A3V8SG25 The 2.4GHz Antenna is an embedded PCB strip. The fundamental emission was measured conducted and radiated where the gain of the antenna is inherently accounted for because of the measurement. Sincerely, Signed : Printed name: Steinar Fagerli Title: Production Manager Company Name: Nofence AS

B DETAIL B SCALE 2 : 1 B C D 12 A 3214 B A 56 C SHEET SIZE New front geometri 2022-05-03 2022-06-22 2023-01-09 Approved Date MG MG MG Approved By moved text 2022-05-03 Q 2022-06-22 R S 2023-01-09 new text Changed By AS AS AS Revision Description Changed Date EUROPEAN PROJECTION Main casing SheepGoat S 523001 2019-08-22 AS WEIGHT: 85.67 Ra 3.2 PC/ABS Polyplend 65FS NT A4 SHEET 2 OF 2SCALE: 1:2 DWG NO. TITLE: REVISION DO NOT SCALE DRAWING MATERIAL: DATE SIGNATURE NAME FINISH: UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS Q.A MFG APPV'D CHK'D DRAWN Ral 7016 COLOR: DIN 16901-130 GENERAL TOLERANCE: PART NO. 270015

FCC ID: 2A3V8SG25 FCC 1.1310 General Population/Uncontrolled Exposure Frequency (F)Power (P) Duty Cycle (D) Antenna Gain (G)EIRP 1 EIRP Distance (R) Power Density 2 (PD)Limit 3 MarginPD/Limit MHzdBmdBdBidBmmWcm mW/m 2 mW/cm 2 dB DSSS24025.400.002.27.65.75200.00111.029.410.0011 IC: 28021-SG25 CANADA RSS-102, Issue 5 General Population/Uncontrolled Exposure Frequency (F)Power (P) Duty Cycle (D) Antenna Gain (G)EIRP 1 EIRP Distance (R) Power Density 2 (PD)Limit 4 MaginPD/Limit Exemption Limit 5 MHzdBmdBdBidBmWm W/m 2 W/m 2 dBW DSSS24025.400.002.27.60.005750.20.0115.3526.70.0022.68 1 EIRP = P + D + G 2 Power Density = EIRP/(4xπxR 2 ); Health Canada Technical Guide - Safety Code 6_2015, Eq 5-6 at 5.2; OET Bulletin 65, Edition 97-01, August 1997, Eq (4) 3 FCC 1.1310 Table 1; Limit = F/1500 (300 ≤ F ≤ 1,500); Limit = 1 (1,500 MHz ≤ F ≤ 100,000 MHz) 4 RSS-102 Issue 5 Table 4; Limit = 0.02619 x F 0.6834 (300 MHz ≤ F ≤ 6,000 MHz) 5 RSS-102 Issue 5 at 2.5.2; Exemption Limit = 1.31 x 10 -2 x F 0.6834 (300 MHz ≤ F < 6 GHz)

Total Exposure Ratio (TER) FCC ID: 2A3V8SG25 FCC ID: XPYUBX20VA01 47 CFR 1.1310(e)(1) Maximum Permissible Exposure (MPE) - Limits for General Population/Uncontrolled Exposure BANDMode Frequency (f) Power (P) Antenna Gain (G) Duty Cycle (D)EIRP 1 EIRP R Power Density 2 (PD) Power Density Limit Margin Exposure Ratio (ER) MHz dBm dBi%dBmmWcm mW/cm 2 mW/cm 2 dB eFDD 2NB-IoT185024.274.40100.028.67736200.1461.008.340.15 eFDD 4NB-IoT171024.704.40100.029.10813200.1621.007.910.16 eFDD 5NB-IoT82424.342.60100.026.94494200.0980.557.470.18 eFDD 13NB-IoT77724.942.60100.027.54568200.1130.526.620.22 eFDD 12NB-IoT69923.702.60100.026.30427200.0850.477.400.18 eFDD 66NB-IoT171025.304.40100.029.70933200.1861.007.310.19 eFDD 8NB-IoT89822.822.60100.025.42348200.0690.609.360.12 eFDD 85NB-IoT69824.812.60100.027.41551200.1100.476.280.23549 850GSM824.232.252.6012.525.82382200.0760.558.590.14 850EDGE824.228.002.6050.027.59574200.1140.556.820.21 1900GSM1850.229.054.4012.524.42277200.0551.0012.590.06 1900EDGE1850.226.894.4050.028.28673200.1341.008.730.13 eFDD 2Cat-M1185022.814.40100.027.21526200.1051.009.800.10 eFDD 4Cat-M1171022.864.40100.027.26532200.1061.009.750.11 eFDD 5Cat-M182422.672.60100.025.27337200.0670.559.140.12 eFDD 13Cat-M177722.862.60100.025.46352200.0700.528.700.14 eFDD 12Cat-M169922.792.60100.025.39346200.0690.478.310.15 eFDD 66Cat-M1171022.744.40100.027.14518200.1031.009.870.10 eFDD 25Cat-M1185022.994.40100.027.39548200.1091.009.620.11 eFDD 26Cat-M181422.832.60100.025.43349200.0690.548.930.13 eFDD 8Cat-M189822.832.60100.025.43349200.0690.609.350.12 2400BLE24805.442.2100.07.645.81200.00121.0029.370.0011554 1 EIRP dBm = P + G+10Log(D/100) 2 PD = EIRP mW /(4πR 2 ) TER=0.23549+0.0011554=0.23664< 1 Total Exposure Ratio (TER) IC: 28021-SG25 IC: 8595A-UBX20VA01 Canada RSS-102 Issue 5 (4. Exposure Limits) Table 4: RF Field Strength Limits for Devices Used by the General Public (Uncontrolled Environment) BANDMode Frequency (f) Power (P) Antenna Gain (G) Duty Cycle (D)EIRP 1 EIRP R Power Density 2 (PD) Power Density Limit Margin Exposure Ratio (ER) MHz dBm dBi%dBmWm W/m 2 W/m 2 dB eFDD 2NB-IoT185024.274.40100.028.670.7360.21.464.484.90.33 eFDD 4NB-IoT171024.704.40100.029.100.8130.21.624.244.20.38 eFDD 5NB-IoT82424.342.60100.026.940.4940.20.982.584.20.38 eFDD 13NB-IoT77724.942.60100.027.540.5680.21.132.473.40.46 eFDD 12NB-IoT69923.702.60100.026.300.4270.20.852.304.30.37 eFDD 66NB-IoT171025.304.40100.029.700.9330.21.864.243.60.44 eFDD 8NB-IoT89822.822.60100.025.420.3480.20.692.736.00.25 eFDD 85NB-IoT69824.812.60100.027.410.5510.21.102.303.20.47654 850GSM824.232.252.6012.525.820.3820.20.762.585.30.29 850EDGE824.228.002.6050.027.590.5740.21.142.583.50.44 1900GSM1850.229.054.4012.524.420.2770.20.554.489.10.12 1900EDGE1850.226.894.4050.028.280.6730.21.344.485.20.30 eFDD 2Cat-M1185022.814.40100.027.210.5260.21.054.486.30.23 eFDD 4Cat-M1171022.864.40100.027.260.5320.21.064.246.00.25 eFDD 5Cat-M182422.672.60100.025.270.3370.20.672.585.90.26 eFDD 13Cat-M177722.862.60100.025.460.3520.20.702.475.50.28 eFDD 12Cat-M169922.792.60100.025.390.3460.20.692.305.20.30 eFDD 66Cat-M1171022.744.40100.027.140.5180.21.034.246.10.24 eFDD 25Cat-M1185022.994.40100.027.390.5480.21.094.486.10.24 eFDD 26Cat-M181422.832.60100.025.430.3490.20.692.555.70.27 eFDD 8Cat-M189822.832.60100.025.430.3490.20.692.735.90.25 2400BLE24805.442.20100.07.640.005810.20.0125.4726.80.0021126 1 EIRP dBm = P + G+10Log(D/100) 2 PD = EIRP mW /(4πR 2 ) TER=0.47654+0.0021126=0.47866< 1

Report No. REP002970C Nemko Group Nemko Scandinavia AS, Instituttveien 6, 2007 Kjeller, Norway TEL +47 22 96 03 30 EMAIL [email protected] (Nemko template revision: 2022/01) Test Report Product Animal Collar for Sheep/Goat Name and address of the applicant Nofence Evjevegen 8, 6631 Batnfjordsøra, Norway Name and address of the manufacturer Nofence Evjevegen 8, 6631 Batnfjordsøra, Norway Model SG25 Rating 3.6VDC, rechargeable battery Trademark Nofence Serial number See page 3 Additional information This test report covers Bluetooth Low Energy and intermodulation measurements. This device contains following FCC/ISED certified modules: - U-blox LTE-M FCC ID: XPYUBX20VA01, ISED ID:8595A-UBX20VA01 Tested according to FCC Part 15.247 Frequency Hopping Transmitters / Digital Transmission Systems Industry Canada RSS-247, Issue 2 Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and Licence-Exempt Local Area Network (LE-LAN) Devices FCC KDB 996369 D04 Module Integration Guide V01, section 2e Modular transmitter integration guide-quidance for host product manufactures composite system operation (Co-Location) Order number PRJ0019249 Tested in period 2022-11-07 – 2022-11-25 Issue date 2023-06-05 Name and address of the testing laboratory Nemko Scandinavia AS Instituttveien 6, 2007 Kjeller, Norway CAB Number: FCC: NO0001 ISED: NO0470 An accredited technical test executed under the Norwegian accreditation scheme Prepared by [G.Suhanthakumar] Approved by [Frode Sveinsen] This report shall not be reproduced except in full without the written approval of Nemko. Opinions and interpretations expressed within this report are not part of the current accreditation. This report was originally distributed electronically with digital signatures. For more information please contact Nemko. TEST REPORT FCC Part 15.247 Report no.: REP002970C FCC ID: 2A3V8SG25 ISED ID:28021-SG25 Nemko Scandinavia AS, Instituttveien 6, Kjeller, Norway Page 2 (29) CONTENTS 1 INFORMATION ......................................................................................................................... 3 1.1 Test Item ................................................................................................................................................... 3 1.2 Normal test condition ................................................................................................................................. 4 1.3 Test Engineer(s) ........................................................................................................................................ 4 1.4 Antenna Requirement ................................................................................................................................ 4 1.5 EUT Operating Modes ............................................................................................................................... 4 1.6 Comments ................................................................................................................................................. 4 2 TEST REPORT SUMMARY ...................................................................................................... 5 2.1 General ..................................................................................................................................................... 5 2.2 Test Summary ........................................................................................................................................... 6 3 TEST RESULTS ........................................................................................................................ 7 3.1 Occupied Bandwidth (99% BW) ................................................................................................................. 7 3.2 DTS Bandwidth ......................................................................................................................................... 9 3.3 Peak Power Output ................................................................................................................................. 11 3.4 Conducted Emissions at Antenna Connector ........................................................................................... 13 3.5 Restricted Bands of operation .................................................................................................................. 15 3.6 Radiated Emissions, Band Edge.............................................................................................................. 16 3.8 Radiated Emission, 30 – 1000 MHz. ........................................................................................................ 18 3.9 Radiated Emissions, 1-26 GHz ................................................................................................................ 19 3.10 Power Spectral Density (PSD) ................................................................................................................. 25 4 Measurement Uncertainty ..................................................................................................... 27 5 LIST OF TEST EQUIPMENT................................................................................................... 28 6 BLOCK DIAGRAM .................................................................................................................. 29 6.1 Power Line Conducted Emission ............................................................................................................. 29 6.2 Test Site Radiated Emission .................................................................................................................... 29 TEST REPORT FCC Part 15.247 Report no.: REP002970C FCC ID: 2A3V8SG25 ISED ID:28021-SG25 Nemko Scandinavia AS, Instituttveien 6, Kjeller, Norway Page 3 (29) 1 INFORMATION 1.1 Test Item Name Nofence collar Model/version SG25 FCC ID 2A3V8SG25 ISED ID 28021-SG25 Serial number Radiated sample: 290113 Conducted sa…

Text truncated - open the document above for the full version.

TEST SET-UP PHOTOS Project no.: prj0019249 FCC ID: 2A3V8SG25 ISED ID: 28021-SG25 Page 1 (1) SG25- Goat Radiated Emissions 30 – 1000 MHz Radiated Emissions above 1GHz, XY plane Radiated Emissions above 1 GHz, XZ plane Radiated Emissions above 1 GHz, YZ plane Radiated Emissions above 1 GHz