2A449-B0106RGB side mirror

1. Read these instructions and check to be sure all parts and tools are accounted for. 2. Please retain these installation instructions for future reference and parts ordering information. 1. Please read the installation instructions carefully before you start. 2. If the vehicle is clean and free of other debris, it will be easy to install. 3. For your safety and to ensure a satisfactory installation, please complete all the installation steps in the order shown below. PRODUCT MANUAL Complete journey of dreams BEFORE YOU BEGIN PRODUCT INFORMATION INSTALLATION TIPS FUNCTION IMPORTANT 1 1245 3 2 3 4 5 Left Mirror Right Mirror Bluetooth Controller Extension Harness Allen Wrench x1 x1 x1 x2 x1 STEP 1STEP 2 SKU: B0106-13601BK www.kemimoto.com Designed by Kemimoto Group Kemimoto All Rights Reserved,Inf ringement must be prosecuted. KKK 1 of 3 1.65-2.0inch 360° mirror 220° 01) It fits 1. 65 - 2.0 inches round pipe.02) Slightly loosen screw [E], the mirror body can be rotated 360°. 03) Slightly loosen screw [F], the mirror body can be swung f ront and back 220°. STEP 1: Install the mirror parts [A, B,C,D] on roll cage in order, and tighten the screws [A]. 010203 A B C F E D STEP 2: Repeat step 1 to install the other side. Complete journey of dreams 3 4 4 male connector female connector female connector male connector female connector male connector female connector STEP 3: Connect the mirror harness [4], extension harness [4], bluetooth controller [3] and vehicle power by following the wiring diagram shown above. STEP 3 Connect the extension wire harness Connect the extension wire harness Connect the extension wire harness Connect the extension wire harness Brown positive (+) Blue negative (-) Attach the bluetooth controller to relay(+) and vehicle power supply(-). STEP 4: Scan the QR code on the controller [3], download the control APP, then open the APP and connect to Bluetooth to control the RGB lights. SKU: B0106-13601BK www.kemimoto.com Designed by Kemimoto Group Kemimoto All Rights Reserved,Inf ringement must be prosecuted. KKK 2 of 3 ALL Devices ALL Devices MusicVoice pickupTask RGB patternPaletteDream pattern 1 2 3 STEP 4 The device list is automatically connected, and you can manually click to connect or disconnect. Click to enter group management Note: When the color and mode do not match: 1. Settings in the upper right corner of the APP. 2. RGB sequence. RGB sequences Cancel OK RGB BGR BRG GBR RBG GRB Please select correct sequence of your RGB LED strip among the checks above, and verify the result by clicking R,G,B button. REDGREENBLUE KEMIMOTO APP Complete journey of dreams SKU: B0106-13601BK www.kemimoto.com Designed by Kemimoto Group Kemimoto All Rights Reserved,Inf ringement must be prosecuted. KKK 3 of 3 FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

GUANGZHOU ISSYZONE TECHNOLOGY CO.,LTD U.S. Agent Designation for Service of Process (Applicant and U.S. Agent are Separate Parties) TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046, USA ATTENTION: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Bouge Tech Inc FRN: 0033768409 Contact Name: Jason Zheng Street Address: 457 E MCGLINCY LN, CAMPBELL, City/Province/Zip: CA 95008 Telephone No: +86-13450452927 Email: [email protected] This letter is to confirm that we (“the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature: Date: 2023/05/12 Signed by (Printed Name/Title): The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: GUANGZHOU ISSYZONE TECHNOLOGY CO.,LTD Grantee Code: 2A449 FCC ID: 2A449-B0106 Contact Name: Typing Yang Street Address: 3Floor,Tairong Business center C10, No.63 Xizeng Road, Liwan District, City/Province/Zip: Guangzhou, China Telephone No: 020-8545412 Email: [email protected] Applicant Signature: Date: 2023/05/12 Signed by (Printed Name/Title): Typing Yang /Manager

(GUANGZHOU ISSYZONE TECHNOLOGY CO.,LTD) (2023.05.16 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for (FCC ID: 2A449-B0106) [GUANGZHOU ISSYZONE TECHNOLOGY CO.,LTD] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, (Applicant signature) (Applicant printed name) Typing Yang (GUANGZHOU ISSYZONE TECHNOLOGY CO.,LTD) (2023.05.16) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for (FCC ID: 2A449-B0106) [GUANGZHOU ISSYZONE TECHNOLOGY CO.,LTD] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Typing Yang

GUANGZHOU ISSYZONE TECHNOLOGY CO.,LTD 2023.5.16 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: CONFIDENTIALITY REQUEST FOR EUT NAME: RGB side mirror Trademark: N/A MODEL : B0106-13701BK FCC ID: 2A449-B0106 To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the - Block Diagram - Schematics - Operational Description required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, Client’s signature: Client’s name / title : Typing Yang/Vic GM Contact information / address: 3Floor, Tairong Business center C10,No.63 Xizeng Road, Liwan District Guangzhou China 510000

GUANGZHOU ISSYZONE TECHNOLOGY CO.,LTD 2023.5.16 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen BCTC Testing Co., Ltd to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Client’s signature: Client’s name / title : Typing Yang/Vic GM Contact information / address: 3Floor, Tairong Business center C10,No.63 Xizeng Road, Liwan District Guangzhou China 510000

External Photos

Label & label location 5mm*10mm FCC ID:2A449-B0106

Internal Photos Antenna

FCC §15.247 (i), §2.1091 – RF Exposure FCC ID: 2A449-B0106 Applied procedures / limit According to FCC §15.247(i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm 2 ) Averaging Time |E| 2 ,|H| 2 or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 Note: ƒ is frequency in MHz * = Power density limit is applicable at frequencies greater than 100 MHz Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm 2 ) Averaging Time |E| 2 ,|H| 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1.0 30 Note: f = frequency in MHz * = Plane-wave equivalent power density MPE PREDICTION Predication of MPE limit at a given distance, Equation from OET Bulletin 65, Edition 97-01 Where: S = power density P = power input to antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna, R=0.2m TEST RESULTS Tune up Produce power Maximum peak output power (dBm) Output power to antenna (mW) Antenna Gain (numeric) Power Density (S) (mW/ cm2) Limit (mW / cm2 ) Result 2.4G 0±1 1 1.26 1.820(2.6dBi) 0.00046 1 Pass

Report No.: BL-SZ2350137-AA 1 / 1 EUT PHOTO --BLANK BELOW-- Antenna

Report No.: BL-SZ2350137-AO 1 / 2 TEST SETUP PHOTOS Report No.: BL-SZ2350137-AO 2 / 2 --BLANK BELOW--

Report No.: BL-SZ2350137-901 Tel: +86-755-66850100 E-mail: [email protected] Page No. 1 / 12 Web: www.titcgroup.com Template No.: TRP-Passive-EN (2022-09-07) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China TEST REPORT Applicant: GUANGZHOU ISSYZONE TECHNOLOGY CO., LTD Address: 3Floor, Tairong Business center C10, No.63 Xizeng Road, Liwan District, Guangzhou, China Equipment Type: PCB Onboard Antenna Model Name: B0106-13701BK Brand Name: N/A Test Standard: IEEE Std 149-2021 Sample Arrival Date: May 05, 2023 Test Date: May 08, 2023 Date of Issue: May 15, 2023 ISSUED BY: Shenzhen BALUN Technology Co., Ltd. Tested by: Mai Jintian Checked by: Zou Liu Approved by: Tolan Tu (Testing Director) _______________ _______________ _______________ Report No.: BL-SZ2350137-901 Tel: +86-755-66850100 E-mail: [email protected] Page No. 2 / 12 Web: www.titcgroup.com Template No.: TRP-Passive-EN (2022-09-07) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China Revision History Version Issue Date Revisions Rev. 01 May 15, 2023 Initial Issue TABLE OF CONTENTS 1 GENERAL INFORMATION ........................................................................................................ 3 1.1 Test Laboratory ................................................................................................................... 3 1.2 Test Location ....................................................................................................................... 3 2 PRODUCT INFORMATION ....................................................................................................... 4 2.1 Applicant Information ........................................................................................................... 4 2.2 Manufacturer Information .................................................................................................... 4 2.3 General Description for Equipment under Test (EUT) ......................................................... 4 2.4 Ancillary Equipment ............................................................................................................. 4 2.5 Technical Information .......................................................................................................... 4 3 SUMMARY OF TEST RESULTS ............................................................................................... 5 3.1 Test Standards .................................................................................................................... 5 3.2 Test Verdict ......................................................................................................................... 5 3.3 Test Uncertainty .................................................................................................................. 5 4 GENERAL TEST CONFIGURATIONS ...................................................................................... 6 4.1 Test Condition ..................................................................................................................... 6 4.2 Test Equipment List ............................................................................................................. 6 4.3 Test Setup ........................................................................................................................... 7 ANNEX A TEST RESULTS ........................................................................................................... 8 A.1 Gain and Efficiency ............................................................................................................. 8 A.2 VSWR ................................................................................................................................. 8 ANNEX B RADIATION PATTERN ................................................................................................ 9 ANNEX C TEST SETUP PHOTOS ............................................................................................. 11 ANNEX D EUT PHOTO .............................................................................................................. 11 Report No.: BL-SZ2350137-901 Tel: +86-755-66850100 E-mail: [email protected] Page No. 3 / 12 Web: www.titcgroup.com Template No.: TRP-Passive-EN (2022-09-07) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 1 GENERAL INFORMATION 1.1 Test Laboratory Name Shenzhen BALUN Technology Co., Ltd. Address Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China Phone Number +86 755 6685 0100 1.2 Test Location Name Shenzhen BALUN Technology Co., Ltd. Location Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 1/F, Building B, Ganghongji High-tech Intelligent Industrial Park, No. 1008, Songbai Road, Yangguang Community, Xili Sub-district, Nanshan District, Shenzhen, Guangdong Province, P. R. China Report No.: BL-SZ2350137-901 Tel: +86-755-66850100 E-mail: [email protected] Page No. 4 / 12 Web: www.titcgroup.com Template No.: TRP-Passive-EN (2022-09-07) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 2 PRODUCT INFORMATION 2.1 Applicant Information Applicant GUANGZHOU ISSYZONE TECHNOLOGY CO., LTD Address 3Floor, Tairong Business center C10, No.63 Xizeng Road, Liwan District, Guangzhou, China 2.2 Manufacturer Information Manufacturer N/A Address N/A 2.3 General Description for Equipment under Test (EUT) EUT Name PCB Onboard Antenna Model Name Under Test B0106-13701BK Antenna Type PCB Antenna Dimensions 12.2*5.9 mm 2.4 Ancillary Equipment Note: Not applicable. 2.5 Technical Information Test Frequencies 2400MHz, 2410MHz, 2420MHz, 2…

Text truncated - open the document above for the full version.

No.：BCTC/RF-EMC-007 Page: 1 of 40 Edition：A.5 TEST REPORT Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC2303996222E Applicant: GUANGZHOU ISSYZONE TECHNOLOGY CO.,LTD Product Name: RGB side mirror Model/Type reference: B0106-13701BK Tested Date: 2023-03-31 to 2023-04-25 Issued Date: 2023-04-25 Report No.: BCTC2303996222E No.：BCTC/RF-EMC-007 Page: 2 of 40 Edition：A.5 FCC ID:2A449-B0106 The test report is effective only with both signature and specialized stamp.This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Testing Co., Ltd, this report can’t be reproduced except in full.The tested sample(s) and the sample information are provided by the client. Product Name: RGB side mirror Trademark: N/A Model/Type reference: B0106-13701BK Prepared For: GUANGZHOU ISSYZONE TECHNOLOGY CO.,LTD Address: 3Floor, Tairong Business center C10,No.63 Xizeng Road, Liwan District Guangzhou China 510000 Manufacturer: GUANGZHOU ISSYZONE TECHNOLOGY CO.,LTD Address: 3Floor, Tairong Business center C10,No.63 Xizeng Road, Liwan District Guangzhou China 510000 Prepared By: Shenzhen BCTC Testing Co., Ltd. Address: 1-2/F., Building B, Pengzhou Industrial Park, No.158, Fuyuan 1st Road, Zhancheng, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, China Sample Received Date: 2023-03-31 Sample tested Date: 2023-03-31 to 2023-04-25 Issue Date: 2023-04-25 Report No.: BCTC2303996222E Test Standards: FCC Part15.247 ANSI C63.10-2013 Test Results: PASS Remark: This is Bluetooth BLE radio test report. Tested by: Approved by: Kelsey Tan/ Project Handler Zero Zhou/Reviewer Report No.: BCTC2303996222E No.：BCTC/RF-EMC-007 Page: 3 of 40 Edition：A.5 Table Of Content Test Report Declaration Page 1. Version .................................................................................................................. 5 2. Test Summary ....................................................................................................... 6 3. Measurement Uncertainty ..................................................................................... 7 4. Product Information And Test Setup ..................................................................... 8 4.1 Product Information ............................................................................................... 8 4.2 Test Setup Configuration ...................................................................................... 9 4.3 Support Equipment ............................................................................................... 9 4.4 Channel List ........................................................................................................ 10 4.5 Test Mode ........................................................................................................... 10 4.6 Table of parameters of text software setting ....................................................... 10 5. Test Facility And Test Instrument Used ............................................................... 11 5.1 Test Facility ......................................................................................................... 11 5.2 Test Instrument Used .......................................................................................... 11 6. Conducted Emissions .......................................................................................... 13 6.1 Block Diagram Of Test Setup .............................................................................. 13 6.2 Limit .................................................................................................................... 13 6.3 Test procedure .................................................................................................... 13 6.4 EUT Operating Conditions .................................................................................. 13 6.5 Test Result .......................................................................................................... 13 7. Radiated Emissions ............................................................................................. 14 7.1 Block Diagram Of Test Setup .............................................................................. 14 7.2 Limit .................................................................................................................... 15 7.3 Test procedure .................................................................................................... 16 7.4 EUT operating Conditions ................................................................................... 17 7.5 Test Result .......................................................................................................... 17 8. Radiated Band Emission Measurement And Restricted Bands Of Operation ..... 21 8.1 Block Diagram Of Test Setup .............................................................................. 21 8.2 Limit .................................................................................................................... 21 8.3 Test Procedure ................................................................................................... 22 8.4 EUT Operating Conditions .................................................................................. 22 8.5 Test Result .......................................................................................................... 23 9. Power Spectral Density Test ............................................................................... 24 9.1 Block Diagram Of Test Setup .............................................................................. 24 9.2 Limit .................................................................................................................... 24 9.3 Test procedure .................................................................................................... 24 9.4 EUT Operating Conditions ..........................................................…

Text truncated - open the document above for the full version.

Report No.: BCTC2303996222E No.：BCTC/RF-EMC-007 Page: 39 of 40 Edition：A.5 15. EUT Test Setup Photographs Radiated Measurement Photos