INSTRUCTION MANUAL EN DE DK ES FR IT NL RU SE EN STEP 1 Connect the power supply cable to the bottom of Autoblow A.I. and plug it into any electrical outlet (120v-240v). The device must remain plugged into the wall outlet during use. STEP 2 Move the slider to the ON position. The gripper will then move to the top position. STEP 3 Follow the actions in the drawings to insert the sl eeve into the gripper. Use the supplied white pl astic stick to assist sl eeve insertion. The sl eeve will be properly seated when the sl eeves bottom ridge rests below the gripper, and its top ridge sits above the gripper. THE MACHINE MUST BE USED WITH SLEEVE INSERTED OR INJURY MAY RESULT. STEP 4 Press the button to activate mode 1 and press it again to cycle through the 10 modes. Each of the 10 experiences can be enjoyed at 10 speeds. Press the and buttons to control the speed of each mode. Press the button to pause any mode. Press the button a second time to unpause. When paused, the LEDs will slowly BLUE. Modes appear as single blu e lights. Speeds appear as green lights. Fl ashing RED LEDs indicate the motor has temporarily overheated and the machine will stop. If this happens, turn the machine and wait 10 minutes before trying to operate it again. STEP 5 You must apply a water-based lubricant both to your penis and to the interior of the sl eeve prior to use. Every 10 minutes during use, apply more lu bricant. DO NOT USE SILICONE LUBRICANT AS IT WILL DAMAGE THE SLEEVE MATERIAL. STEP 6 Turn the machine before removi ng the sl eeve. To remove the sl eeve, gently pull it in an upwards direction. EN STEP 7 Pour out any liquid from inside the sl eeve and then wash it using soap and warm water. Spray a sex toy cleaner into the sl eeve and then rinse it again. To dry the interior of the sl eeve, insert a paper towel or small fabric towel and twist it several times in a downward manner to help soak up any water remaining inside. DO NOT ATTEMPT TO TURN THE SLEEVE INSIDE OUT. IT MAY TEAR. STEP 8 NEVER submerge the Autoblow A.I. in water. Use a damp cloth to clean its exterior surfaces only. Store the machine in a cool dry place out of direct sunlight. To extend the life of your Autoblows sl eeve and to maintain its si lky texture, dust the sl eeve with corn starch after cleaning it and store the sl eeve in a sealed pl astic bag. WARNINGS DO NOT BLOCK THE AIR EXHAUST VENT ON THE BOTTOM OF THE MACHINE. THIS IS AN ELECTRICAL APPLI ANCE. DO NOT USE IN OR NEAR WATER. INJURY OR DEATH MAY RESULT. THIS DEVICE MUST BE USED IN CONJUNCTION WITH AN AUTOBLOW A.I. SLEEVE. DO NOT USE THE PRODUCT WITHOUT A SLEEVE INSTALLED OR INJURY MAY RESULT. WARRANTY Autoblow warrants that the electrical parts and motor of Autoblow A.I. are covered for a period of one (1) year. The warranty is from the date of original purchase, against defects due to faulty workmanship or materials. The warranty covers the main body of the Autoblow A.I. product only, provided it has not been tampered with, or taken apart. The warranty does not cover the reusable sl eeve. The warranty does not cover cosmetic deterioration caused by normal wear and tear. The warranty also does not cover damage caused by accident, misuse, or neglect. Any attempt to open or take apart the Autoblow A.I. will void the warranty. DE SCHRITT 1 Schließen Sie das Stromversorgungskabel an der Unterseite des Autoblow A.I. an und stecken Sie es in eine Steckdose (120v-240v). Das Gerät muss während des Betriebs an der Steckdose angeschlossen bleiben. SCHRITT 2 Bewegen Sie den Schieber in die Position ON. Der Greifer bewegt sich dann in die oberste Position. SCHRITT 3 Folgen Sie den Anweisungen in den Zeichnungen, um die Hül se in den Greifer einzusetzen. Verwenden Sie den mitgelieferten weißen um das Einführen der Hül se zu erleichtern. Die Hül se sitzt richtig, wenn der untere Grat der Hül se unter dem Greifer liegt und sein oberer Grat über dem Greifer sitzt. DIE MASCHINE MUSS DER EINGESETZTEN HÜLSE VERWENDET WERDEN ODER ES KÖNNEN VERLETZUNG ENTSTEHEN. SCHRITT 4 Drücken Sie , um Modus 1 zu aktivieren, und erneut, um die 10 verschiedenen Modi zu durchl aufen. Jeder der 10 Modi kann mit 10 Geschwindigkeiten genossen werden. Drücken Sie die Tasten und , um die Geschwindigkeit der einzelnen Modi einzustellen. Drücken Sie die Taste , um einen beliebigen Modus anzuhalten. Drücken Sie die Taste ein zweites Mal, um die Wiedergabe zu beenden. Im Pausemodus blinken die LEDs langsam BLAU. Die Modi erscheinen als einzelne bl aue Lichter. Geschwindigkeiten erscheinen als grüne Lichter. Blinkende ROTE LEDs zeigen an, dass der Motor vorübergehend überhitzt ist und die Maschi ne stoppt. Schalten Sie in diesem Fall das Gerät aus und warten Sie 10 Min uten, bevor Sie es erneut bedienen. SCHRITT 5 Sie müssen vor der Verwendung ein Gleitmittel auf Wasserbasis sowohl auf Ihren Penis als auch auf das Innere der Hül se auftragen. Tragen Sie während des Gebrauchs alle 10 Min uten erneut Gleitmittel auf. VERWENDEN SIE KEIN GLEITMITTEL MIT SILIKON, DA DAS MATERIAL DER HÜLSE BESCHÄDIGT WERDEN KANN. SCHRITT 6 Schalten Sie die Maschine aus, bevor Sie die Hül se entfernen. Um die Hül se zu entfernen, ziehen Sie sie vorsichtig nach oben. DK TRIN 1 Forbind strømforsynin gskablet til bunden af Autoblow A.I . og tilslut enheden til en stikkontakt (129v-240v). Enheden skal være tils luttet stikkontakten under brug. TRIN 2 Slå kontakten over på ON-indstillingen. Grebsenheden vil derefter sig til toppositionen. TRIN 3 Følg vejledningen der er angivet på tegningen, for at indsætte mundstykket i grebsenheden. Brug den medfølgende hvide pl astikpind til at indsætte mundstykket. Mundstykket vil være korrekt indsat når mundstykkets bundkant hviler under grebsenheden og topkanten sidder over grebsenheden. MASKINEN SKAL BRUGES MED INDSAT MUNDSTYKKE, ELLERS KAN SKADER FOREKOMME. TRIN 4 Tryk på for at aktivere tilstand 1 og tryk igen for at gå videre gennem de 10 andre tilstande. Hver af de 10 tilstande kan nydes i…

Text truncated - open the document above for the full version.

Attestation Statements

VERYINTELLIGENTECOMMERCEINC. Declarationonmodeldifference Wetheundersignedherebyconfirmthatthesemodelsareidentical,andallmodelshave thesameRFmoduleandantenna,PCBlayout,schematicsandcomponent.thedifferenceis themodelNumbersandenclosuretype.AutoblowAI+，AutoblowA.I.Plus,CG573are Non-transparentshell，Othermodelsaretransparentshells. Production name FCCIDTrademarkModelno. Motorized Penis Stroking MachineWith Insertable Sleeve 2A4AW-AUTOBLOW-AIAutoblowAI+,AutoblowAI+ Clear,AutoblowA.I.Plus, AutoblowA.I.PlusClear, CG573 Sincerely, BrianSloan Manager VERYINTELLIGENTECOMMERCEINC. VERYINTELLIGENTECOMMERCEINC. 109E,17thSt,Suite4,Cheyenne,WY82001,UnitedStates

Cover Letter(s)

VERY INTELLIGENT ECOMMERCE INC. 2022-12-16 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR (EUT Name: Motorized Penis Stroking Machine With Insertable Sleeve/Model: Autoblow AI+, Autoblow AI+ Clear, Autoblow A.I. Plus, Autoblow A.I. Plus Clear, CG573 /FCC ID: 2A4AW-AUTOBLOW-AI) To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the (Block Diagram ,Operational Description,Schematics) required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, Brian Sloan Manager VERY INTELLIGENT ECOMMERCE INC. 109 E, 17th St, Suite 4, Cheyenne, WY 82001, United States

Cover Letter(s)

VERY INTELLIGENT ECOMMERCE INC. 2022-12-16 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize DongGuan Anci Electronic Technology Co., Ltd. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Brian Sloan Manager VERY INTELLIGENT ECOMMERCE INC. 109 E, 17th St, Suite 4, Cheyenne, WY 82001, United States

External Photos

Models: Autoblow AI+, Autoblow A.I. Plus, CG573 Models: Autoblow A.I. Plus Clear, Autoblow AI+ Clear

Internal Photos

ANT

RF Exposure Info

RF EXPOSURE EVALUATION EUT Specification EUT Motorized Penis Stroking Machine With Insertable Sleeve Model Number Autoblow AI+ FCC ID 2A4AW-AUTOBLOW-AI Antenna gain (Max) -2.49dBi Operation Frequency 2402-2480MHz Input Rating DC 12V, 3A Classification Per Stipulated Test Standard §15.247(i), §2.1093 Modulation 802.11b: DSSS(DBPSK/DQPSK/CCK) 802.11g/n: OFDM(BPSK/QPSK/16QAM/64QAM) Max. output power 802.11b: 6.45dBm 802.11g: 6.40dBm 802.11n(HT20): 6.27dBm Test Requirement: According to §15.247(i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Routine SAR evaluation refers to that specifically required by §2.1093, using measurements or computer simulation. When routine SAR evaluation is not required, portable transmitters with output power greater than the applicable low threshold require SAR evaluation to quality for TCB approval. One antenna is available for the EUT. The minimum separation distance is 5mm. WIFI: According to KDB 447498, no stand-alone required for BT antenna, and no simultaneous SAR measurement is required. Signature: Tiger Xu Date: 2022-12-28 Transmit Frequency (MHz) Mode Measured Power (dBm) Tune up Power (dBm) Max tune up power(dBm) Calculation Result 1-g SAR 2412 802.11b 6.45 0±1 7 1.556789 3 2437 6.14 0±1 7 1.564836 3 2462 6.19 0±1 7 1.572842 3 2412 802.11g 6.32 0±1 7 1.556789 3 2437 6.28 0±1 7 1.564836 3 2462 6.40 0±1 7 1.572842 3 2412 802.11n2 0 6.09 0±1 7 1.556789 3 2437 6.18 0±1 7 1.564836 3 2462 6.27 0±1 7 1.572842 3

Test Report

OTA TEST REPORT Applicant Espressif Systems Product ESP-ANT A Model ESP-ANT A Report No. YXA1711-1424OTA01R3 Issue Date November 27, 2020 TA Technology (Shanghai) Co., Ltd. tested the above equipment in accordance with the requirements in ANSI/IEEE Std 149-2008. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Prepared b y: Peng Tao Approved by: Kai Xu TA Technology (Shanghai) Co., Ltd. No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai, China TEL: +86‐021‐50791141/2/3 FAX: +86‐021‐50791141/2/3‐8000 OTA Test Report Report No: YXA1711-1424OTA01R3 TA Technology (Shanghai) Co., Ltd. TA-MB-04-008O P age 2 of 11 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. TABLE OF CONTENTS 1. General Information ....................................................................................................................... 3 1.1. Notes of the Test Report ................................................................................................... 3 1.2. Testing laboratory .............................................................................................................. 3 1.3. Laboratory Environment .................................................................................................... 3 2. General Description of Equipment under Test ............................................................................... 4 2.1. Applicant Information ......................................................................................................... 4 2.2. Manufacturer Information .................................................................................................. 4 2.3. Information of EUT ............................................................................................................ 4 2.4. Test Date ........................................................................................................................... 4 2.5. Applied Standards ............................................................................................................. 5 3. Test Conditions .............................................................................................................................. 6 3.1. Test Configuration ............................................................................................................. 6 3.2. Test Measurement ............................................................................................................. 6 4. Test Results ................................................................................................................................... 7 4.1. Gain and Efficiency ............................................................................................................ 7 4.2. Voltage Standing Wave Ratio (VSWR) .............................................................................. 8 4.3. Antenna S11 ...................................................................................................................... 8 5. Test Equipment List ....................................................................................................................... 9 APPENDIX A: 2-D Pattern Plots ............................................................................................................. 10 APPENDIX B: The EUT Appearance and Test Configuration .................................................................. 11 B.1 EUT Appearance ................................................................................................................... 11 OTA Test Report Report No: YXA1711-1424OTA01R3 TA Technology (Shanghai) Co., Ltd. TA-MB-04-008O P age 3 of 11 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 1. General Information 1.1. Notes of the Test Report This report shall not be reproduced in full or partial, without the written approval of TA technology (shanghai) co., Ltd.The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein .Measurement Uncertainties were not taken into account and are published for informational purposes only. This report is written to support regulatory compliance of the applicable standards stated above. This report must not be used by the client to claim product certification, approval, or endorsement by any government agencies. 1.2. Testing laboratory Company: TA Technology (Shanghai) Co., Ltd. Address: No.145, Jintang Rd, Tangzhen Industry Park, Pudong City: Shanghai Post code: 201201 Country: P. R. China Contact: Xu Kai Telephone: +86-021-50791141/2/3 Fax: +86-021-50791141/2/3-8000 Website: http://www.ta-shanghai.com E-mail: [email protected] 1.3. Laboratory Environment Temperature Min. =19°C，Max. = 25°C Relative humidity Min. =40%，Max. =72% Shield effect 0.7-6GHz > 100dB Ground resistance <0.5 OTA Test Report Report No: YXA1711-1424OTA01R3 TA Technology (Shanghai) Co., Ltd. TA-MB-04-008O P age 4 of 11 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 2. General Description of Equipment under Test 2.1. Applicant Information Company: Espressif Systems Address: #204, Block 2, 690 Bibo Road, Zhang Jiang High-Tech Park, Shanghai, P. R. China 2.2. Manufacturer Information Company: Espressif Systems Address: #204, Block 2, 690 Bibo Road, Zhang Jiang High-Tech Park, Shanghai, P. R. China 2.3. Information of EUT General information EUT Description Product Name: ESP-ANT A Model ESP-ANT A HW Version: / SW Version: / Antenna Type: Fixed Antenna (PCB Antenna) Antenna Manufacturer: Espressif Systems Test Frequency: 2400MHz ~ 2500MHz Test lab. of the antenna gain and radiation pattern measurement: TA Technology (Shanghai) Co., Ltd. This revised report (R…

Text truncated - open the document above for the full version.