2A5UA-W193 in 1 Wireless Charger

FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The FCC certification of this device refers to RF exposure testing performed in typical operating conditions, where a person is no closer than 20 centimeters from the device surface at all times, except for non-repetitive patterns with transient time intervals in the order of a second. Only in the stated conditions, the device is shown to fully comply with the FCC RF Exposure requirements of KDB 447498.

- Shenzhen Autige Technology Co., Ltd - Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 8/30/2024 U.S. Agent Designation Shenzhen Autige Technology Co., Ltd acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2A5UA-W19): Name and company of U.S. agent: UUX GROUP INC Physical U.S. address of agent: 36 South 18th Avenue, Suite A Brighton, CO USA 80601 FRN of U.S. agent: 0033701590 Email address of U.S. agent: [email protected] UUX GROUP INC acknowledges their obligation to accept service of process on behalf of Shenzhen Autige Technology Co., Ltd. Shenzhen Autige Technology Co., Ltd with the FRN 0032137861 accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Sam she Manager Shenzhen Autige Technology Co., Ltd Signature Jack Fu Manager UUX GROUP INC 48_[model] US_Agent_2.911(d)(7) - U, V05

Page 1 of 4 FCC ID: 2A5UA-W19 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. EUT Constructional Details External EUT Photo Photo 1 Photo 2 Page 2 of 4 FCC ID: 2A5UA-W19 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 3 Photo 4 Page 3 of 4 FCC ID: 2A5UA-W19 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 5 Photo 6 Page 4 of 4 FCC ID: 2A5UA-W19 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 7 ---The End---

Label Size: L45mm * W30mm 1. The label is silk-screen on the sample 3 in 1 Wireless Charger Model Name: W19 FCC ID: 2A5UA-W19 L W

Page 1 of 9 FCC ID: 2A5UA-W19 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. EUT Constructional Details Internal EUT Photo Photo 1 Photo 2 Page 2 of 9 FCC ID: 2A5UA-W19 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 3 Photo 4 Page 3 of 9 FCC ID: 2A5UA-W19 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 5 Photo 6 Phone Coil Watch Coil Page 4 of 9 FCC ID: 2A5UA-W19 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 7 Photo 8 Earphone Coil Page 5 of 9 FCC ID: 2A5UA-W19 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 9 Photo 10 Page 6 of 9 FCC ID: 2A5UA-W19 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 11 Photo 12 Page 7 of 9 FCC ID: 2A5UA-W19 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 13 Photo 14 Page 8 of 9 FCC ID: 2A5UA-W19 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 15 Photo 16 Page 9 of 9 FCC ID: 2A5UA-W19 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 17 ------End------

Page 1 of 16 Report No.:AITSZ24062701W3 RF Exposure Evaluation Client Information: Applicant: Shenzhen Autige Technology Co., Ltd Applicant add.: 3rd Floor, Building B, Zhaofeng Industrial Zone, No. 3 Hangkong Road, Hangcheng Street, Baoan District,518126,Shenzhen,China Manufacturer: Shenzhen Autige Technology Co., Ltd Manufacturer add.: 3rd Floor, Building B, Zhaofeng Industrial Zone, No. 3 Hangkong Road, Hangcheng Street, Baoan District,518126,Shenzhen,China Product Information: Product Name: 3 in 1 Wireless Charger Model No.: W19 Brand Name: N/A FCC ID: 2A5UA-W19 Applicable standards: FCC CFR 47 PART 1, § 1.1310 KDB 680106 D01 Wireless Power Transfer v04 Prepared By: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Date of Receipt: Jun. 27, 2024 Date of Test: Jun. 27, 2024 ~ July 05, 2024 Date of Issue: July 05, 2024 Test Result: Pass This device described above has been tested by Guangdong Asia Hongke Test Technology Limited and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Note: This report shall not be reproduced except in full, without the written approval of Guangdong Asia Hongke Test Technology Limited, this document may be altered or revised by Guangdong Asia Hongke Test Technology Limited, personal only, and shall be noted in the revision of the document. This test report must not be used by the client to claim product endorsement. Reviewed by: Approved by: Leon.yi Sean She Page 2 of 16 Report No.:AITSZ24062701W3 1 CONTENTS COVER PAGE Page 1 CONTENTS 2 2 TEST FACILITY 4 2.1 Deviation from standard 4 2.2 Abnormalities from standard conditions 4 2.3 Test Location 4 3 GENERAL INFORMATION 5 4 TEST METHODOLOGY 6 4.1 Measuring Standard 6 4.2 Requirements 6 4.3 Limits 6 4.4 Test Setup 7 4.5 Test Procedure 7 5 Equipment Approval Considerations 8 5.1 Description of the test mode 9 5.2 Peripheral List 9 5.3 Test Instruments list 9 5.4 Test Result 10 5.5 Test Setup photo 14 Page 3 of 16 Report No.:AITSZ24062701W3 Revision History Revision Issue Date Revisions Revised By 00 July 05, 2024 Initial Issue Sean She Page 4 of 16 Report No.:AITSZ24062701W3 2 TEST FACILITY The test facility is recognized, certified or accredited by the following organizations: FCC-Registration No.: 251906 Designation Number: CN1376 Guangdong Asia Hongke Test Technology Limited has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. IC —Registration No.: 31737 CAB identifier: CN0165 The 3m Semi-anechoic chamber of Guangdong Asia Hongke Test Technology Limited has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 31737 A2LA-Lab Cert. No.: 7133.01 Guangdong Asia Hongke Test Technology Limited has been accredited by A2LA for technical competence in the field of electrical testing, and proved to be in compliance with ISO/IEC 17025: 2017 General Requirements for the Competence of Testing and Calibration Laboratories and any additional program requirements in the identified field of testing. 2.1 Deviation from standard None 2.2 Abnormalities from standard conditions None 2.3 Test Location Guangdong Asia Hongke Test Technology Limited Address: B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Page 5 of 16 Report No.:AITSZ24062701W3 3 GENERAL INFORMATION EUT Name: 3 in 1 Wireless Charger Model No: W19 Serial Model: W19B Brand Name: N/A Test sample(s) ID: AITSZ24062701-1 Sample(s) Status: Engineer sample Operation frequency: Coil1: For Phone: 113kHz-205kHz Coil2: For Earphone: 113kHz-205kHz Coil3: Watch: 300kHz-350kHz Modulation Technology: ASK Antenna Type: Coil1/Coil2/Coil3: Loop coil Antenna Antenna gain: Coil1/Coil2/Coil3: 0dBi Hardware version.: N/A Software version.: N/A Power supply: Input: DC 9V/2A,12V/2A Output (Phone): 5W/7.5W/ 10W/ 15W Output (Earphone): 3W Output (Smart watch): 2.5W Model different: The model names and colors are different Note: For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. Page 6 of 16 Report No.:AITSZ24062701W3 4 TEST METHODOLOGY 4.1 Measuring Standard According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1091 RF exposure is calculated. According KDB680106 D01: KDB 680106 D01 Wireless Power Transfer v04. 4.2 Requirements According to the item 3 of KDB 680106 D01v04: Inductive wireless power transfer applications that meet all of the following requirements are excluded from submitting an RF exposure evaluation. (1) Mobile Device and Portable Device Configurations (2) Equipment Authorization Procedures for Devices Operating at Frequencies Below 4 MHz (3) The aggregate H-field strengths anywhere at or beyond 15 cm surrounding the device, and 20 cm away from the top surface. 4.3 Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Page 7 of 16 Report No.:AITSZ24062701W3 4.4 Test Setup 4.5 Test Procedure 1) The RF exposure test was performed in anechoic chamber. 2) The measurement probe was placed at test distance (15 cm from all sides and 20 cm from the top) which is between the edge of the charger and the geometric center of probe. 3)…

Text truncated - open the document above for the full version.

Page 1 of 25 Report No.: AITSZ24062701W2 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. FCC TEST REPORT Client Information: Applicant: Shenzhen Autige Technology Co., Ltd Applicant add.: 3rd Floor, Building B, Zhaofeng Industrial Zone, No. 3 Hangkong Road, Hangcheng Street, Baoan District,518126,Shenzhen,China Manufacturer: Shenzhen Autige Technology Co., Ltd Manufacturer add.: 3rd Floor, Building B, Zhaofeng Industrial Zone, No. 3 Hangkong Road, Hangcheng Street, Baoan District,518126,Shenzhen,China Product Information: Product Name: 3 in 1 Wireless Charger Model No.: W19 Brand Name: N/A FCC ID: 2A5UA-W19 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Prepared By: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Date of Receipt: Jun. 27, 2024 Date of Test: Jun. 27, 2024 ~ July 05, 2024 Date of Issue: July 05, 2024 Test Result: Pass This device described above has been tested by Guangdong Asia Hongke Test Technology Limited and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Note: This report shall not be reproduced except in full, without the written approval of Guangdong Asia Hongke Test Technology Limited, this document may be altered or revised by Guangdong Asia Hongke Test Technology Limited, personal only, and shall be noted in the revision of the document. This test report must not be used by the client to claim product endorsement. Reviewed by: Approved by: Leon.yi Sean She Page 2 of 25 Report No.: AITSZ24062701W2 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. 1 Contents Page COVER PAGE 1 CONTENTS ........................................................................................................................................................... 2 2 TEST SUMMARY .................................................................................................................................................. 5 2.1 STATEMENT OF THE MEASUREMENT UNCERTAINTY ............................................................................................. 5 2.2 MEASUREMENT UNCERTAINTY ............................................................................................................................ 5 3 TEST FACILITY ..................................................................................................................................................... 6 3.1 DEVIATION FROM STANDARD ............................................................................................................................... 6 3.2 ABNORMALITIES FROM STANDARD CONDITIONS .................................................................................................... 6 3.3 TEST LOCATION ................................................................................................................................................. 6 4 GENERAL INFORMATION ................................................................................................................................... 7 4.1 EUT TEST MODE ............................................................................................................................................... 8 4.2 DESCRIPTION OF TEST SETUP............................................................................................................................. 8 4.3 PERIPHERAL LIST ............................................................................................................................................... 9 4.4 EUT PERIPHERAL LIST ....................................................................................................................................... 9 5 EQUIPMENTS LIST FOR ALL TEST ITEMS ..................................................................................................... 10 6 CONDUCTED EMISSION TEST ......................................................................................................................... 11 6.1 CONDUCTED EMISSION MEASUREMENT ................................................................................................ 11 6.2 POWER LINE CONDUCTED EMISSION LIMITS ........................................................................................... 11 6.3 TEST PROCEDURE ...................................................................................................................................... 11 6.4 DEVIATION FROM TEST STANDARD ......................................................................................................... 11 6.5 TEST SETUP ................................................................................................................................................. 12 6.6 EUT OPERATING CONDITIONS .................................................................................................................. 12 6.7 TEST RESULT .................................................................................................................................................. 13 7 RADIATED EMISSION MEASUREMENT .......................................................................................................... 15 7.1 RADIATED EMISSION LIMITS .............................................................................................................................. 15 7.2 ANECHOIC CHAMBER TEST SETUP DIAGRAM ..................................................................................................... 16 7.3 TEST PROCEDURE ...........…

Text truncated - open the document above for the full version.

1. Coil attached magnetic disc, magnetic disc size 43.5±1mm, L first slot 2. Wrap tape 1-2Ts around the coil outlet position Coil and diskette Hot air wire Lead-free tin strip Magnetic sheet glue High-temperature adhesive paper Copper wire temperature Hot air wire 0.08*24 strands Lead-free tin strip Manganese zinc hard disk with L slot Yellow gum 9999 8mm wide high temperature adhesive paper G43 Headphone coil

                  !"# $%!&'())'#* &"))+,%!&'())'#!")"(  -.$ /$ 012 34 562 34 782 34 9:;<; => ?@A BCBDEFEBD GH BCBDEFEBD IJK BCBDEFEBD LMN BCBDEFEBD IOA BCBDEFEBD IOA BCBDEFEBD   +  + $   P Q$"")"   +   R *)S#! 012 34 562 34 782 34 9:;<; =>             !"#$%!"#&'()* +,- ./  0 11 234 5 354 6476 8 9: ;( <=> ?@ A A B   0  : C D E F G H IJKLMN :FFS ;< ; >TU V62W 4X436Y9Z2 Y[\X3] ]6W9 ~V484] ~ )==T€ ‚ XZ9V49† Y[\X 3] ˆ‰Š ‹Œ ‹Œ ŽE:[F[:‘]8 Y[\X3] 563 9Y 3Z3X4 ‘]8 Y[\X3] šZY]Y ŽEE[› 3Z~Z Y[\X3] B  Ÿ A    ABB 99¥Z9†¥Z99Z9†Y \X3] -,,¦§ ̈, € ©u %&ª -,,¦§ ̈, € « ¬­!-,® «, ̄° ±²³'¬­!- ®  ́=T; < ́¶ 2¹º ¡P»[›:F”” C‘4W :C32 ¼6½¾¿ À>ÀÁ <=>¶>);TU ¶T )==T€)À 2363¹ºZ9Z2VWZ64 3~543‘692 - !$#&,'!,, :F+ 1. The coil is attached to the magnetic disc, the magnetic disc size is 43.5±1mm, the thickness is 0.8±0.05mm, and the L-slot is opened 2. Wrap tape 1-2Ts around the coil outlet position 3. The bottom of the magnetic separator should be affixed with back glue Coil and diskette Individual coil value Silk covered thread 0.08*105 strands Acetone silk-covered wire 0.08*105 strands Lead-free tin strip Lead-free tin strip Magnetic sheet Manganese zinc hard disk with L slot glue Yellow gum 9999 High-temperature adhesive paper 7mm wide high temperature adhesive paper Rubber backing Copper wire temperature G43 slotted magnetic coil 3M           !"#  $%&%& '""""  $&(%$ ')")" ' $&(%( '*+," + $&&-$& ' "" " $&%%%- +"" ) * ,  ! +', ')  ""+")" .+' *'"**)'"'"+," /01+',')*,+) '*"" 0 2 345  6. 789:   )"; <= )>?@ABC )"++ )",+' ')" +" +)"*+ "))+'" ))+, * ,  ! ))+" .)+,+ /01)")+" DEF   G 6.G60 06/H H I JK"L M 6  345 NAOPQ'K' RSRTU V WXYZ['>>\ 0].^  I ^ _`a DEF  06/ ^ 0 ]H 06.  6bH cdeRfg

           !"# $%  &' () * +* * ,-.&-'  /,-.''. 012 34 562 34 782 34 9:; <=<>?@?<> AB <=<>?@?<> 012 34 562 34 782 34 CDEFE GH 9IJ <=<>?@?<> KL; <=<>?@?<>  M N*  CDEFE GH OPQ <=<>?@?<> 9:; <=<>?@?<> RSTU                !"##$%&'("# )*  + ,, -./ 0 .0/ 1/21 3 45 6%7 89%: ;< = = >   +  5 ? @ A B C 5BBH 01. 4I J# KL" #MNOO RS4TI IUVW. T 89%::X6YJ Y$ X99$YZX[ .S.W/ _`ab cdcef`ghiea eg'jdfk pI4qrIs/SIVW .T  -.1.tuS4S-p -tu [ 8v wS1/ .x0/ yzUz{|?A}} ?~/w NX >   =   "#v"‚ƒ„ …„†‡"#Z ‹‹‹‹ f ‘’“f ‘’“ X99$YZ% ” p/3/T rxT1w4 rx ~T3 IUVW.T „v9Y6•– .~14- 5?.- —1˜™š .SxS IUVW.T =>> ~q?B 44sS4qsS44S4qI VW.T 44sS4qsS44S4qIVW.T œzUz{}}|?A ?~/w žŸ7 ¡¢ 6%8 6 :YJ :$ 8v : 8v ‘'("# £¤¥‘ Magnetic core magnet Copper wire gum Lead-free tin strip Lead-free tin strip glue Copper wire temperature Soft magnetism Gauss 18 Double-sided adhesive backing Watch coil      !"#$   %$&' ((( )'$)&&&'* ) ++, )*$%$&' % , &$$*&'-  (, )*$$'&'& .$%& -)$$ )'$$&'- /$*$%)' &-)$$$ %)&&&' 0   %& '*)$-* )$ %*&'  1 234  5/ 67 89 : &;&-<= %$>? @ABC &'$$ &*$$$ )&'$$ %&-$$)$ &'*$%$ * . &-$$ /&'$$$ 0 &&$& DEF GAHI)J) = K L MNO :   5/ 5::50P  $$K=QJ$R STUVWX  YZ[\ 234 ]^ P _/L =;:5 ::50 L

Page 1 of 2 FCC ID: 2A5UA-W19 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Test Setup Photo DCD Conduction Radiation (9KHz-30MHz) Page 2 of 2 FCC ID: 2A5UA-W19 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Radiation (30MHz-1000MHz) ------End------