2A5ZQ-RD02Deadbolt lock

13 15 5 16 17 10 CHECK THE DOOR’S DIMENSIONS Step 1: Measure to confirm that the door is between ( 35mm ~54mm) thick. Step 2 : Measure to confirm that the hole in the door is (54mm). Step 3 : Measure to confirm that the backset is either-(60-70mm). Step 4 : Measure to confirm that the hole in the door edge is 1" (25 mm). Note : If you have a new door, please drill the holes according to Drill Template. 1"~ 3 8 / 2" 1 8 / 2" 3 8 / 2" 3 4 / 2" 1 8 / 1"~ 3 8 / 2" 1 8 / (35~54mm) 2" 3 4 / (70mm) 2" 3 8 / (60mm) 2" 1 8 / (54mm) " 1 (25mm) or 4 Strike plate 2" 3 4 / (70mm) 2" 3 8 / (60mm) or INSTALL LATCH AND STRIKE PLATE 1.Install latch into the door, make sure latch fits inside the door opening. 2. Install the strike into the door frame, make sure the latch can go into the strike smoothly. Screws A 2 " 3 4 / 2 " 3 4 / - 2 " 3 8 / If your door’s backset is ( 70mm), pull-out the face plate to extend. 60 OR 70MM Angle faces jamb 11 Deadbolt latch 2 PRODUCT DESCRIPTION Exterior panel Fingerprint reader Mechanical key hole Type-C USB interface LED indicator Socket Reset button Interior panel Battery cover Set button Deadbolt knob 3 INCLUDED IN THE BOX ASSEMBLY DIAGRAM Keys 2PCS Screws C 3PCS Screws B 3PCS Screws A 4PCS Strike plateDeadbolt 1PC Interior mounting plate 1PC Interior panel 1PC Exterior panel 1PC Warranty card 1PC Exterior panel Deadbolt Interior panel Interior mounting plate Battery cover Screws A Screws B Screws C INSTALL EXTERIOR PANEL 7 DO NOT CLOSE THE DOOR UNTIL THE DOOR LOCK IS FULLY INSTALLED AND THE BATTERIES ARE INSTALLED. If the deadbolt latch is extended, use a flat-head screwdriver to retract it. From outside of your door,align the spindle vertically through the latch and push the exterior panel in unit it fit against the door. Step 1 : Install the interior mounting plate from the inside of the door. Make sure the connect cable is running through the small hole below spindle. Use the provided srews B to secure the mount plate to the exterior panel. Step 2 : Cable Screws B CHECK BEFORE INSTALLATION 6 RIGHT OR LEFT OPEN FOR YOUR DOOR. RIGHT HINGE Indoor Indoor Outdoor Outdoor LEFT HINGE Indoor Indoor Outdoor Outdoor 9 Very important Step 3 : The Interior Panel Knob should be kept in a vertical position, see image on the left. Insert the cable connector into the socket of the interior panel. Make sure the connector is firmly connected with the socket. Push the excess wire into the door, align the interior panel against the mounting plate. Step4: Use Screw C provided and tighten the interior panel. Note: Turn the interior panel knob to check if the deadbolt protrudes and retracts smoothly. Close the door to check if the deadbolt protrudes and retracts smoothly. If not, please review your installation or contact support our centre. INSTALL INTERIOR PANEL FOR RIGHT HINGR Screws C INSTALLING BATTERIES Insert 4 * AA batteries according to positive and negative polarity. Do not use rechargeable batteries. DOWNLOAD THE GEEKSMART APP 1. App Download Instructions A. Scan the QR code on the right you can use Android and iOS to download the APP. B. Android version software can be downloaded in the Google Play store. Search "GeekSmart". C. iOS version of the software can be downloaded in the iPhone App Store. Search "GeekSmart". 2. Register and log in with your E-mail address. FCC WARNING Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. TROUBLESHOOTING ADDING DEVICE Tap the add button”+”.Select the smart lock. 1 . Adding new door lock by app (Note : Keep your phone close by the door during this process). HOW TO ADD FINGERPRINT Click member mangement. Continue to follow the instruction on the App interface. Click me. 14 HOW TO DELETE FINGERPRINT Tap the fingerprint you want to delete. Tap delete. 12 Select your lock.The door opening direction is automatically identified successfully. After adding the device(as ) , you will see the F02 main page (as ). At the same time the lock will identify left or right hinge door automatically, and the bolt will come out in 40 seconds, which means the lock system is well prepared. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio /TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 18 SPECIFICATIONS Technical Parameters NameParameter DescriptionNo. 1 2 3 4 5 6 7 8 9 10 11 USB Fingerprints max Low power warning Voltage range Stand-by current Working current Unlock time Range of working Temperature Type-C/ 5V2A 50 4.8V±0.2 ≈1.5 sec Exterior panel -13°F~158°F Interior panel 14°F~131°F Door thickness Material Alluminum alloy lock+ plastic cover plate body Power4*AA alkaline batteries 4.5~6.5V Connect to APP 75uA Without connect to …

Text truncated - open the document above for the full version.

GEEKTECHNOLOGYCO.LTD 2023-06-27 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:AttestationStatementsPart2.911(d)(5)(i)requestfor(FCCID: 2A5ZQ-RD02 ) [ GEEKTECHNOLOGYCO.LTD ](“theapplicant”)certifiesthattheequipmentfor whichauthorizationissoughtisnot“covered”equipmentprohibitedfromreceivingan equipmentauthorizationpursuanttosection2.903oftheFCCrules. Sincerely, ACTEURZHONG testengineer GEEKTECHNOLOGYCO.LTD 1275BloomfieldAve.Unit141,Building16,Fairfield,NewJerseyUnitedStates GEEKTECHNOLOGYCO.LTD 2023-06-27 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:AttestationStatementsPart2.911(d)(5)(ii)requestfor(FCCID:2A5ZQ-RD02) [GEEKTECHNOLOGYCO.LTD](“theapplicant”)certifiesthat,asofthedateofthe filingoftheapplication,theapplicantisnotidentifiedontheCoveredListasanentity producing“covered”equipment. Sincerely, ACTEURZHONG testengineer GEEKTECHNOLOGYCO.LTD 1275BloomfieldAve.Unit141,Building16,Fairfield,NewJerseyUnitedStates

Attestation Statements (2023-06-26) TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046, USA RE: Attestation Statements Part 2.911(d)(7) request for (FCC ID:2A5ZQ-RD02，FRN： 0032168296) (GEEK TECHNOLOGY CO.LTD), the undersigned, hereby authorize (Lucky Cowboy Global Services, LLC) to act as our designated U.S. agent for service of process, (GEEK TECHNOLOGY CO.LTD) accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. (Lucky Cowboy Global Services, LLC) accepts the responsibility to act as designated U.S. agent for service of process. Applicant Information： Company name: GEEK TECHNOLOGY CO.LTD Contact Name: ACTEUR ZHONG Address: 1275Bloomfield Ave. Unit 141，Building16，Fairfield，New Jersey，United States Telephone No: 18124901378 Email: [email protected] Signature [ACTEUR ZHONG] U.S. Agent Information: Company Name: Lucky Cowboy Global Services, LLC Address: 2213 S. Braeswood Blvd. #12E Houston, TX 77030 USA FRN: 0033510934 Contact Name: Louie Liu Telephone No: +1 (713) 992-3369 Email: [email protected] Signature [Louie Liu]

Declarationonmodeldifferenc GEEK TECHNOLOGY CO.LTD e Wetheundersignedherebyconfirmthatthesemodelsareidentical,andallmodelshavethe sameRFmoduleandantenna,PCBlayout,schematicsandcomponent.Onlythemodelsnameare different. Productionname FCCI Trademark D Deadbolt lock GEEK TAL E 2A5 ZQ -RD02 Model no. RD02 , RD03 Sincerely, ACTEUR ZHONG

GEEKTECHNOLOGYCO.LTD 2022-06-27 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:CONFIDENTIALITYREQUESTFOR(EUTName:Deadboltlock/Model:RD02, RD03/FCCID:2A5ZQ-RD02) ToWhomItMayConcern: Thisletterservesasanofficialrequestforconfidentialityundersections0.457and0.459 ofCFR47.Wehaverequestedthatthe(BlockDiagram,OperationalDescription,Schematics)required tobesubmittedwiththisapplicationbepermanentlywithheldfrompublicreview. Theabovematerialscontaintradesecretsandproprietaryinformationnotcustomarilyreleasedtothepublic.The publicdisclosureofthesematerialsmaybeharmfultotheapplicantandprovideunjustifiedbenefitstoitscompetitors. Pleasecontactmeifthereisanyinformationyoumayneed. Sincerely, ACTEURZHONG testengineer GEEKTECHNOLOGYCO.LTD 1275BloomfieldAve.Unit141,Building16,Fairfield,NewJerseyUnitedStates

Figure 1. Overall view Figure 2. Overall view Figure 3. Overall view Figure 4. Overall view

Figure 1. Internal view Figure 2. Internal view Figure 3. Internal view Figure 4. Internal view Antenna Figure 5. Internal view Figure 6. Internal view

RF EXPOSURE EVALUATION EUT Specification EUT Deadbolt lock Model Number RD02, RD03 (All models are the same except the material of the rear shell is different, We choose model RD02 for all tests.) FCC ID 2A5ZQ-RD02 Antenna gain (Max) 1.3 dBi Operation Frequency 2402 MHz to 2480 MHz Input Rating DC 6V Max. output power -7.82 dBm Test Requirement: According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency(RF) Radiation as specified in §1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density(mW/cm 2 ) Average Time (A) Limits for Occupational/Control Exposures 300-1500 -- -- F/300 6 1500-100000 -- -- 5 6 (B) Limits for General Population/Uncontrol Exposures 300-1500 -- -- F/1500 6 1500-100000 -- -- 1 30 11.1 Friis transmission formula: Pd= (Pout*G)\ (4*pi*R 2 ) Where Pd= Power density in mW/cm 2 Pout=output power to antenna in mW G= Numeric gain of the antenna relative to isotropic antenna Pi=3.1416 R= distance between observation point and center of the radiator in cm=20cm Pd the limit of MPE, 1mW/cm 2 . If we know the maximum gain of the nd total power input to the antenna, through the calculation, we will know the distance where the MPE limit is reached. 11.2 Measurement Result Antenna gain: 1.3dBi BLE: Mode Channel Freq. (MHz) Measured power (dBm) Tune-up power (dBm) Max tune-up power (dBm) Antenna Gain （Numeric） Evaluation result (mW/cm2 ) Power density Limits (mW/cm2 ) GFSK 2402 -8.02 -8±1 -7 1.349 -0.002152 1 GFSK 2440 -8.44 -8±1 -7 1.349 -0.002265 1 GFSK 2480 -7.82 -8±1 -7 1.349 -0.002099 1 Signature: Tiger Xu Date: 2023-06-26

1/12DD321606-CD DD321606-CD规格书 SPECIFICATION DESCRIPTION ChipAntenna PARTNO. DD321606-CD VERSION V1.1 2 /12DD321606-CD Contents 1.NamingRules3 2.AntennaSpecification4 3.AntennaDimension5 4.TestData6-8 5.LayoutGuide9 6.SolderingConditions10 7.PackagingInformation 11-12 3 /12DD321606-CD 1.NamingRules Type：DD-ABCDEF-GH 1.DD：ShortcutforDongDianTechnology 2.ABCDEF：ABLength(mm)CD：Width(mm) EFHeight(mm) Forexample:5020105.0mm*2.0mm 3.G ： Material （ C-CeramicP-Polymer ） 4.H：Feeding（S-SingleD-Dual） 4 /12DD321606-CD 2.AntennaSpecification OutlineDimensions3.2x1.6x0.6(mm) GroundPlane 3.2x1.6(mm) FrequencyRange2.4GHz~2.5GHz Impedance50OhmNominal Bandwidth (under-10dBreturnloss) 100MHz(Typ.) RadiationOmni-directional PeakGain 1.3dB i(Typ.) Efficiency 60% (Typ.) PolarizationLinearPolarization StorageTemp -40°C~+85°C Color Brown 5 /12DD321606-CD 3.AntennaDimension TypeLWTa SKT3216 3.2 ±0.2 1.6 ±0.2 0.6 ±0.2 0.4 ±0.2 TypeW1W2W3W4 SKT3216 0.4 ±0.2 0.4 ±0.2 2.4 ±0.2 1.6 ±0.2 6 /12DD321606-CD 4.TestData: 4.1ELECTRICALCHARACTERISTICSS11 7 /12DD321606-CD 4.2RadiationPattern EfficiencyPeakGainDirectivity 2400MHz57.45%1.3dBi2.45dBi 2450MHz60.65%1.75dBi2.89dBi 2500MHz56.75%1.45dBi2.23dBi 8 /12DD321606-CD ChamberCoordinateSystem 9 /12DD321606-CD 5.LayoutGuide: SolderLandPattern: Landpatternforsoldering(blackmarkingareas)isas shownbelow.Matchingcircuitisneededforgood performance,whencustomer’sdeviceisdifferent. 10 /12DD321606-CD 6.SolderingConditions: TypicalSolderingProfileforLead-freeProcess 11 /12DD321606-CD 7.TapingSpecifications: TapeDimensions(Unit:mm)&Quantity TypeAA’BCDEFT Qantity/ Reel Type Material SKT3216 4.0 ±0.1 4.0 ±0.1 1.95 ±0.1 3.50 ±0.1 2.0 ±0.05 3.5 ±0.1 8.0 ±0.1 0.85 ±0.1 4,000pcs Plastic (Embossed) ReelDimensions(Unit:mm) TypeABCDEF SKT3216 2.3 ±0.5 17 ±0.5 13.5 ±0.5 178 ±1 75 ±3 1.4 ±0.2 12 /12DD321606-CD LeaderandTrailerTape SolderingConditions: (1)Temperature:5~35°C,relativehumidity(RH):45~75%. (2)Non-corrosiveenvironment

TRF No.: 01-R001-3A-LE TRF Originator: GTG TRF Date: 2022-06-29 Web: www.gtggroup.com E-mail: [email protected] Tel.: 86-400 755 8988 ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT FCC PART 15 SUBPART C REQUIREMENT OF Deadbolt lock Model No.: RD02, RD03 Trademark: GEEK TALE FCC ID: 2A5ZQ-RD02 Report No.: E01A23040185F00101 Issue Date: June 26, 2023 Prepared for GEEK TECHNOLOGY CO.LTD 1275Bloomfield Ave. Unit 141, Building16, Fairfield, New Jersey, United States Prepared by Dong Guan Anci Electronic Technology Co., Ltd. 1-2 Floor, Building A, No.11, Headquarters 2 Road, Songshan, Lake Hi-tech Industrial Development Zone, Dongguan City, Guangdong Pr., China. This report shall not be reproduced, except in full, without the written approval of Dong Guan Anci Electronic Technology Co., Ltd. 1 of 48 Report No.: E01A23040185F00101 TRF No.: 01-R001-3A-LE Global Testing , Great Quality. VERIFICATION OF COMPLIANCE Applicant: GEEK TECHNOLOGY CO.LTD 1275Bloomfield Ave. Unit 141, Building16, Fairfield, New Jersey, United States Manufacturer: HOMEEASY INDUSTRIAL CO., LIMITED Flat/Rm 17/F Royal Commercial Centre, 56 Parkes Street, Jordan Kowloon, HONG KONG Product Description: Deadbolt lock Trade Mark: GEEK TALE Model Number: RD02, RD03 (All models are the same except the material of the rear shell is different, We choose model RD02 for all tests.) Sample number: A23040185 001 We hereby certify that: The above equipment was tested by Dong Guan Anci Electronic Technology Co., Ltd. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10-2013 and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.247(2022). Date of Test : May 31, 2022 to June 02, 2023 Prepared By: Checked By: Duke Dyson Project Engineer Project Engineer Approved By: Tiger Laboratory Supervisor 2 of 48 Report No.: E01A23040185F00101 TRF No.: 01-R001-3A-LE Global Testing , Great Quality. Modified Information Version Summary Revision Date Report No. Ver.1.0 Original Report / E01A23040185F00101 3 of 48 Report No.: E01A23040185F00101 TRF No.: 01-R001-3A-LE Global Testing , Great Quality. Table of Contents THIS REPORT SHALL NOT BE REPRODUCED, EXCEPT IN FULL, WITHOUT THE WRITTEN APPROVAL OF ................................................................................................................. 0 1. GENERAL INFORMATION ................................................................................................... 5 1.1 PRODUCT DESCRIPTION .......................................................................................................... 5 1.2 TEST METHODOLOGY .............................................................................................................. 5 2. TEST FACILITY ...................................................................................................................... 6 3. DESCRIPTION OF TEST MODES....................................................................................... 7 4. SUMMARY OF TEST RESULTS ......................................................................................... 9 6DB BANDWIDTH MEASUREMENT ............................................................................................... 9 5. TEST SYSTEM UNCERTAINTY ........................................................................................ 10 6. RADIATED EMISSION TEST ............................................................................................. 11 7.1 MEASUREMENT PROCEDURE ................................................................................................. 11 7.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ............................................................ 13 7.3 MEASUREMENT EQUIPMENT USED: ........................................................................................ 14 7.4 RADIATED EMISSION LIMIT .......................................................................................................... 15 7.5 MEASUREMENT RESULT .......................................................................................................... 16 7.6 RADIATED MEASUREMENT PHOTOS: ........................................................................................... 22 7. 6DB BANDWIDTH MEASUREMENT ............................................................................... 23 8.1 MEASUREMENT PROCEDURE ................................................................................................. 23 8.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ............................................................ 23 8.3 MEASUREMENT EQUIPMENT USED: ............................................................................................ 23 8.4 LIMIT ........................................................................................................................................ 23 8.5 MEASUREMENT RESULTS: ..................................................................................................... 23 9. MAXIMUM PEAK OUTPUT POWER TEST .............................................................................. 26 9.1 MEASUREMENT PROCEDURE ................................................................................................. 26 9.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ............................................................ 26 9.3 MEASUREMENT EQUIPMENT USED: ............................................................................................ 26 9.4 PEAK POWER OUTPUT LIMIT ....................................................................................................... 26 9.5 MEASUREMENT RESULTS: ...................................................................................................... 26 10. POWER SPECTRAL DENSITY MEASUREMENT ............................................................…

Text truncated - open the document above for the full version.