2A64E-88405001Wireless charging assembly

WIRELESS CHARGING PRODUCT INTRODUCTION Due to the latest iPhone wireless charging system upgrade, the old wireless charging module cannot charge the iPhone before 2018. Therefore, the old one needs to be replaced with the latest wireless charging module to make it adapt to the latest iPhone.Our wireless charging module is fully developed according to the original structure and performance, which ensures the stability and safety of users when charging, and allows you to upgrade your car with the latest wireless charging function at a cheap price. HOW TO INSTALL 01 Remove the old wireless charging module (Different cars have different positions). 02 Unplug the old harness module. 03 Connect the harness to the adapter harness of the new module. 04 Connect the adapter harness plug with the new module. 05 Install the new module to the vehicle. HOW TO WORK When the new module is working, it still display a“ lightning icon” on the screen (Different cars have different positions). FCC REQUIREMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.

QI AUTOMOTIVE CO.,LTD. (2022.09.21) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR (Wireless charging assembly / 88405001/ FCC ID: 2A64E-88405001 ) To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☐ Internal Photos ☐ NOTE 1 ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No required to be submitted with this application be permanently withheld from public review. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. Please contact me if there is any information you may need. Sincerely, Signature: Name: Zhe Luo Title: Legal

QI AUTOMOTIVE CO.,LTD. (2022.09.22) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize (Shenzhen CTB Testing Technology Co., Ltd.) to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Signature: Name: Zhe Luo Title: Legal

External Photos

Model: 88405001 FCC ID: 2A64E-88405001 Label Location

Internal Photos ANT

S henzhen CTB Testing Technology Co., Ltd. Report No.: CTB220913037RFX EMF Report Te l : 4008-707-283 Web: http://www.ctb-lab.net Page1 of 7 RF EXPOSURE REPORT Compiled by: Reviewed by: Approved by: Arron Liu Bin Mei Rita Xiao / Director Note: If there is any objection to the inspection results in this report, please submit a written report to the company within 15 days from the date of receiving the report. The test report is effective only with both signature and specialized stamp. This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen CTB Testing Technology Co., Ltd. this report can’t be reproduced except in full. The tested sample(s) and the sample information are provided by the client. “*” indicates the testing items were fulfilled by subcontracted lab. “#” indicates the items are not in CNAS accreditation scope. P roduct Name: Wireless charging assembly FCC ID: 2A64E-88405001 Trademark: N/A Model Number: 88405001 Prepared For: QI AUTOMOTIVE CO., LT D. Address: No.1 Luanhe Road, Economic and Technological Development Zone, Jiaozhou, QingDao, Shandong Manufacturer: QI AUTOMOTIVE CO., LT D. Address: No.1 Luanhe Road, Economic and Technological Development Zone, Jiaozhou, QingDao, Shandong Prepared By: Shenzhen CTB Testing Technology Co., Ltd. Address: Floor 1&2, Building A, No. 26 of Xinhe Road, Xinqiao Community, Xinqiao Street, Baoan District, Shenzhen, Guangdong, China. Sample Received Date: Sep. 02, 2022 Sample tested Date: Sep. 02, 2022 to Sep. 13, 2022 Issue Date: Sep. 13, 2022 Report No.: CTB220913037RFX Test Standards FCC CFR 47 part1, 1.1307(b), 1.1310, 47 CFR§2.1091; KDB 680106 D01 RF Exposure Wireless Charging App v03r01 Test Results PA SS Remark: This is wireless charger EMF report. Shenzhen CTB Testing Technology Co., Ltd. Report No.: CTB220913037RFX EMF Report Te l : 4008-707-283 Web: http://www.ctb-lab.net Page2 of 7 Table of Contents Page 1 . GENERAL INFORMATION 3 1.1 . Independent Operation Mode 3 1.2 . Test Supporting System 3 2 .LIST OF T EST AND MEASUREMENT I NSTRUMENTS 4 2.1 . For conducted emission at the mains terminals test 4 3. METHOD OF MEASUREMENT 5 3. 1.Applicable Standard 5 4. TEST RESULT 5 4.1. Conducted Emission at the Mains Terminals Test 5 4.2. Equipment Approval Considerations: 6 4.3. E and H field Strength 6 Shenzhen CTB Testing Technology Co., Ltd. Report No.: CTB220913037RFX EMF Report Te l : 4008-707-283 Web: http://www.ctb-lab.net Page3 of 7 1. GENERAL INFORMATION 1.1. Independent Operation Mode The basic operation mode is: 1.1.1. wireless charger power: 15 W 1.2. Test Supporting System Adapter Description : Adapter Model No. : HP18A-0902000-AU Power Input : AC100-240V~ 1.0A 50/60Hz Output: 9V 2 .0A DC Line : Unshielded, Detachable 1.2m Shenzhen CTB Testing Technology Co., Ltd. Report No.: CTB220913037RFX EMF Report Te l : 4008-707-283 Web: http://www.ctb-lab.net Page4 of 7 2.LIST OF T EST AND MEASUREMENT I NSTRUMENTS 2.1. For conducted emission at the mains terminals test Item Equipment Brand Model No. Serial No. Last calibration Calibrated until 1 EMF TESTER Wavecontrol SMP160 19SN0989 2022.08. 20 2023.08.29 Shenzhen CTB Testing Technology Co., Ltd. Report No.: CTB220913037RFX EMF Report Te l : 4008-707-283 Web: http://www.ctb-lab.net Page5 of 7 3. METHOD OF MEASUREMENT 3. 1.Applicable Standard According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1091 RF exposure is calculated. According KDB680106 D01: RF Exposure Wireless Charging Apps v 03r01. 4. TEST RESULT 4.1. Conducted Emission at the Mains Terminals Test Note: Measurements should be made from all sides and the top of the primary/client pair, with the 15 cm measured from the center of the probe(s) to the edge of the device Test Procedure: a) The RF exposure test was performed on 360 degree turn table in anechoic chamber. b) The measurement probe was placed at test distance (15cm) which is between the edge of the charger and the geometric centre of probe. c) The turn table was rotated 360d degree to search of highest strength. d) The highest emission level was recorded and compared with limit as soon as measurement of each points were completed. e) The EUT were measured according to the dictates of KDB 680106v03r01. Shenzhen CTB Testing Technology Co., Ltd. Report No.: CTB220913037RFX EMF Report Te l : 4008-707-283 Web: http://www.ctb-lab.net Page6 of 7 4.2. Equipment Approval Considerations: The EUT does comply with item 5(b) of KDB 680106 V03R01 1) Power transfer frequency is less than 1MHz Yes, the device operate in the frequency range from 110KHz to 205KHz 2) Output power from each primary coil is less than or equal to 15 watts. Yes, the maximum output power of the primary coil is 15000mW. 3) The system may consist of more than one source primary coils, charging one or more clients. If more than one primary coil is present, the coil pairs may be powered on at the same time. Yes, the transfer system includes three primary coils. 4) Client device is inserted in or placed directly in contact with the transmitter. Yes, client device is placed directly in contact with the transmitter. 5) Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion). Yes, the EUT is a Mobile Wireless Charger 6) The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. Yes, the EUT field strength levels are less 50% x MPE limit. 4.3. E and H field Strength Shenzhen CTB Testing Technology Co., Ltd. Report No.: CTB220913037RFX EMF Report Te l : 4008-707-283 Web: http://www.ctb-lab.net Page7 of 7 E- Field Strength at 15 cm surrounding the EUT and for above the top surface of the EUT，15cm an…

Text truncated - open the document above for the full version.

ANT PHTOT L W H 98mm±0.2 55mm±0.2 0.2mm±0.1

S henzhen CTB Testing Technology Co., Ltd. Report No.: CTB220913036RFX Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 1 of 18 TEST REPORT Compiled by: Reviewed by: Approved by: Arron Liu Bin Mei Rita Xiao / Director N ote: If there is any objection to the inspection results in this report, please submit a written report to the company within 15 days from the date of receiving the report. The test report is effective only with both signature and specialized stamp. This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen CTB Testing Technology Co., Ltd. this report can’t be reproduced except in full. The tested sample(s) and the sample information are provided by the client. “*” indicates the testing items were fulfilled by subcontracted lab. “#” indicates the items are not in CNAS accreditation scope. Product Name: Wireless charging assembly FCC ID: 2A64E-88405001 Trademark: N/A Model Number: 88405001 Prepared For: QI AUTOMOTIVE CO., LT D. Address: No.1 Luanhe Road, Economic and Technological Development Zone, Jiaozhou, QingDao, Shandong Manufacturer: QI AUTOMOTIVE CO., LT D. Address: No.1 Luanhe Road, Economic and Technological Development Zone, Jiaozhou, QingDao, Shandong Prepared By: Shenzhen CTB Testing Technology Co., Ltd. Address: Floor 1&2, Building A, No. 26 of Xinhe Road, Xinqiao Community, Xinqiao Street, Baoan District, Shenzhen, Guangdong, China. Sample Received Date: Sep. 02 , 2022 Sample tested Date: Sep. 02, 2022 to Sep. 13, 2022 Issue Date: Sep. 13, 2022 Report No.: CTB220913036RFX Test Standards FCC Part 15 C Test Results PA SS Remark: This is wireless charger radio test report. Shenzhen CTB Testing Technology Co., Ltd. Report No.: CTB220913036RFX Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 2 of 18 TABLE OF CONTENTS 1. GENERAL INFORMATION .......................................................................................................................... 3 1.1. Report information ................................................................................................................................... 3 1.2. Measurement Uncertainty ....................................................................................................................... 3 1.3. Test Facility ............................................................................................................................................. 3 1.4. Test Uncertainty ...................................................................................................................................... 4 2. PRODUCT DESCRIPTION ........................................................................................................................... 5 2.1. EUT Description ...................................................................................................................................... 5 2.2. Block Diagram of EUT Configuration ...................................................................................................... 5 2.3. Test Conditions........................................................................................................................................ 5 2.4. D escriptionOfSupport Units (Conducted Mode) ...................................................................................... 6 3. TEST RESULTS SUMMARY ........................................................................................................................ 6 4. TEST EQUIPMENT USED ............................................................................................................................ 7 4.1. MEASUREMENT INSTRUMENTS LIST ................................................................................................. 7 5. CONDUCTED EMISSION TEST................................................................................................................... 9 5.1. Block Diagram of Test Setup ................................................................................................................... 9 5.2. Test Standard .......................................................................................................................................... 9 5.3. Conducted Emission Limit ....................................................................................................................... 9 5.4. EUT Configuration on Test ...................................................................................................................... 9 5.5. Operating Condition of EUT .................................................................................................................. 10 5.6. Test Procedure ...................................................................................................................................... 10 5. 7. Test Result ............................................................................................................................................ 10 6. RADIATED EMISSION MEASUREMENT .................................................................................................. 11 6.1. Block Diagram of Test Setup ................................................................................................................. 11 6.2. Test Standard ........................................................................................................................................ 12 6.3. EMI Test Receiver Setup ...................................................................................................................... 12 6.4. Test Procedure ...................................................................................................................................... 12 6.5. Test Result ............................................................................................................................................ 12 7. OCCUPIED BANDWIDTH ....................................…

Text truncated - open the document above for the full version.

Radiated Emission Below 1G 9KHz-30MHz