2A6KK-S1002.1 CH Soundbar Speaker System

S100说明书 尺寸：120mm x 170mm 80g书写纸，黑白印刷，折页，双面印 料号：416-0D3P091-W00R

FCC warning statements: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IC warning statements: -English Warning Statement: RSS -GEN ISSUE 5, 8.4 User manual notice This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B). -French Warning Statement: RSS - Gen version 5, 8.4 avis du manuel de l'utilisateur Cet appareil contient un émetteur / récepteur sans licence conforme au RSS sans licence d'innovation, science et développement économique Canada.L'opération doit satisfaire aux deux conditions suivantes: Cet équipement peut ne pas causer d'interférence. L'équipement doit accepter toute interférence, y compris toute interférence qui pourrait entraîner un fonctionnement indésirable de l'équipement. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are deemed to comply without testing of specifc absorption ratio (SAR).Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation du débit d’absorption spécifque (DAS). This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Lors de l'installation et du fonctionnement de cet équipement, la distance minimale entre le radiateur et le corps doit être de 20 cm.

SHENZHEN WOPET SMART TECHNOLOGY CO., LTD. 2.911 (d)(5)(i) Equipment Type Attestation v1.2 Section 2.911(d)(5)(i) Certification – Equipment Type Company name: SHENZHEN WOPET SMART TECHNOLOGY CO., LTD. Address: ROOM 923, BLOCK A, ECONOMIC BUILDING, HUAFENG, HEADQUARTERS NO. 288, XIXIANG AVENUE, LAODONG COMMUNITY, XIXIANG STREET, BAOAN DISTRICT, SHENZHEN CHINA Product Name: 2.1 CH Soundbar Speaker System FCC ID: 2A6KK-S100 Model(s): S100 2.911(d)(5)(i) Equipment Type We, SHENZHEN WOPET SMART TECHNOLOGY CO., LTD. (“the applicant”) certify that the equipment for which authorization is sought through certification is not:  Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules.  Identified as an equipment type in the “Covered List” NOTE 1 Yours sincerely, Name: Sherry zeng Date: 7/11/2023 Title: General Manager Company name: SHENZHEN WOPET SMART TECHNOLOGY CO., LTD. NOTE 1 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

SHENZHEN WOPET SMART TECHNOLOGY CO., LTD. 2.911 (d)(5)(ii) Applicant Attestation v1.3 Section 2.911(d)(5)(ii) Certification – Applicant (Covered List ) Company name: SHENZHEN WOPET SMART TECHNOLOGY CO., LTD. Address: ROOM 923, BLOCK A, ECONOMIC BUILDING, HUAFENG, HEADQUARTERS NO. 288, XIXIANG AVENUE, LAODONG COMMUNITY, XIXIANG STREET, BAOAN DISTRICT, SHENZHEN CHINA Product Name: 2.1 CH Soundbar Speaker System FCC ID: 2A6KK-S100 Model(s): S100 2.911(d)(5)(ii) Applicant filing We, [SHENZHEN WOPET SMART TECHNOLOGY CO., LTD.] (“the applicant”) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the “Covered List” NOTE 2 , established pursuant to § 1.50002 of this chapter, as an entity producing covered communications equipment. Yours sincerely, Name: Sherry zeng Date: 7/11/2023 Title: General Manager Company name: SHENZHEN WOPET SMART TECHNOLOGY CO., LTD. NOTE 1 Delete option not applicable to this application. NOTE 2 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

JOC Australia Inc * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter 7/11/2023 ATTN.: Reviewing Engineer FCC ID: 2A6KK-S100 Per section 2.911(d)(7) of the FCC rules, SHENZHEN WOPET SMART TECHNOLOGY CO., LTD. (“the applicant”) certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: JOC Australia Inc Physical U.S. Company Address: 18351 Colima Road Ste 585 Rowland Heights, California, 91748 United States of America Agent contact name/Title : Benjamin. Smith/Vice President Agent Email Address: [email protected]/[email protected] Tel No.: +1(626) 217 4778 FRN No.: 0033379421 The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Agent Signed (if different to Applicant): Signed: Signed: Printed name: Sherry zeng Printed name: Benjamin. Smith Title: General Manger Title: Vice President Company Name: SHENZHEN WOPET SMART TECHNOLOGY CO., LTD. Company Name: JOC Australia Inc Date: 7/11/2023 Date: 7/11/2023

SHENZHEN WOPET SMART TECHNOLOGY CO., LTD. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2023-07-11 Subject; Request for Long Term Confidentiality FCC ID: 2A6KK-S100 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram BOM Operational Description Tune-up Procedure SOFTWARE SECURITY REQUIREMENTS FOR U-NII DEVICES It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Signature: July 11, 2023 Name Sherry zeng Position General Manager Company Name SHENZHEN WOPET SMART TECHNOLOGY CO., LTD. Address ROOM 923, BLOCK A, ECONOMIC BUILDING, HUAFENG, HEADQUARTERS NO. 288, XIXIANG AVENUE, LAODONG COMMUNITY, XIXIANG STREET, BAOAN DISTRICT, SHENZHEN CHINA Tel +86-15115879531 Fax / Email [email protected]

SHENZHEN WOPET SMART TECHNOLOGY CO., LTD. Letter of Authorization Company: SHENZHEN WOPET SMART TECHNOLOGY CO., LTD. Address: ROOM 923, BLOCK A, ECONOMIC BUILDING, HUAFENG, HEADQUARTERS NO. 288, XIXIANG AVENUE, LAODONG COMMUNITY, XIXIANG STREET, BAOAN DISTRICT, SHENZHEN CHINA Product Name: 2.1 CH Soundbar Speaker System Model Number(s): S100 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: July 11, 2023 Name Sherry zeng Position General Manager Company Name SHENZHEN WOPET SMART TECHNOLOGY CO., LTD. Address ROOM 923, BLOCK A, ECONOMIC BUILDING, HUAFENG, HEADQUARTERS NO. 288, XIXIANG AVENUE, LAODONG COMMUNITY, XIXIANG STREET, BAOAN DISTRICT, SHENZHEN CHINA Tel +86-15115879531 Fax / Email [email protected]

FCC ID: 2A6KK-S100 IC: 30008-S100

Label Location FCC ID: 2A6KK-S100 IC: 30008-S100 2.1 CH Soundbar Speaker System Model No.: S100

FCC ID: 2A6KK-S100 IC: 30008-S100 BT ANT

FCC ID: 2A6KK-S100 Prediction of MPE at a given distance 1. Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) 2. Test Procedure Equation from page 18 of OET Bulletin 65, Edition 97-01 Where: S = power density P = power input to the antenna G = numeric gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna FCC ID: 2A6KK-S100 3. Result Mode Frequency (MHz) Prediction distance (cm) Maximum output power Prediction distance (cm) Rated Peak RF power output MPE (mW/cm 2 ) Limit (mW/cm 2 ) SAR Test Exclusion dBm mW BT 2402-2480 20 -5.601 20 -4 0.3981 0.0001 1 Yes WiFi Antenna Gain: -0.68dBi, 0.86(numeric) Then SAR evaluation is not required.

ALPHA's reports is using a digital certificate that is trusted on Adobe's official server. If there is no digital certificate or the digital certificate shows damaged in your report. Please do not accept the report. E-mail: [email protected] Tel: 4008300895 Website: http://www.a-lab.cn FCC TEST REPORT FCC ID: 2A6KK-S100 On Behalf of SHENZHEN WOPET SMART TECHNOLOGY CO., LTD. 2.1 CH Soundbar Speaker System Model No.: S100 Prepared for : SHENZHEN WOPET SMART TECHNOLOGY CO., LTD. Address : ROOM 923, BLOCK A, ECONOMIC BUILDING, HUAFENG, HEADQUARTERS NO. 288, XIXIANG AVENUE, LAODONG COMMUNITY, XIXIANG STREET, BAOAN DISTRICT, SHENZHEN CHINA Prepared By : Shenzhen Alpha Product Testing Co., Ltd. Address : Building i, No.2, Lixin Road, Fuyong Street, Bao’an District, 518103, Shenzhen, Guangdong, China Report Number : A2305205-C01-R01 Date of Receipt : July 4, 2023 Date of Test : July 4, 2023- July 7, 2023 Date of Report : July 7, 2023 Version Number : V0 Page 2 of 88 Report No.: A2305205-C01-R01 TABLE OF CONTENTS Description Page 1. Summary of Standards And Results ............................................................................................ 6 1.1. Description of Standards and Results ..................................................................................... 6 2. General Information........................................................................................................................ 7 2.1. Description of Device (EUT) .................................................................................................... 7 2.2. Accessories of Device (EUT) .................................................................................................. 8 2.3. Tested Supporting System Details .......................................................................................... 8 2.4. Block Diagram of connection between EUT and simulators ................................................... 8 2.5. Test Mode Description ............................................................................................................. 8 2.6. Test Conditions ........................................................................................................................ 9 2.7. Test Facility .............................................................................................................................. 9 2.8. Measurement Uncertainty ....................................................................................................... 9 2.9. Test Equipment List ............................................................................................................... 10 3. Maximum Peak Output power ..................................................................................................... 12 3.1. Limit ....................................................................................................................................... 12 3.2. Test Procedure ...................................................................................................................... 12 3.3. Test Setup .............................................................................................................................. 12 3.4. Test Result ............................................................................................................................. 12 4. Bandwidth ..................................................................................................................................... 13 4.1. Limit ....................................................................................................................................... 13 4.2. Test Procedure ...................................................................................................................... 13 4.3. Test Result ............................................................................................................................. 13 5. Carrier Frequency Separation ..................................................................................................... 24 5.1. Limit ....................................................................................................................................... 24 5.2. Test Procedure ...................................................................................................................... 24 5.3. Test Result ............................................................................................................................. 24 6. Number Of Hopping Channel ...................................................................................................... 26 6.1. Limit ....................................................................................................................................... 26 6.2. Test Procedure ...................................................................................................................... 26 6.3. Test Result ............................................................................................................................. 26 7. Dwell Time ..................................................................................................................................... 28 7.1. Test limit ................................................................................................................................. 28 7.2. Test Procedure ...................................................................................................................... 28 7.3. Test Result ............................................................................................................................. 28 8. Radiated emissions ...................................................................................................................... 38 8.1. Limit ....................................................................................................................................... 38 8…

Text truncated - open the document above for the full version.

Page 70 of 88 Report No.: A2305205-C01-R01 Band Edge(Hopping) NVNT 3-DH1 2480MHz Ant1 Hopping Ref Band Edge(Hopping) NVNT 3-DH1 2480MHz Ant1 Hopping Emission Page 71 of 88 Report No.: A2305205-C01-R01 10. POWER LINE CONDUCTED EMISSIONS 10.1.Block Diagram of Test Setup 10.2.Limit Frequency Maximum RF Line Voltage Quasi-Peak Level dB(V) Average Level dB(V) 150kHz ~ 500kHz 66 ~ 56* 56 ~ 46* 500kHz ~ 5MHz 56 46 5MHz ~ 30MHz 60 50 Notes: 1. * Decreasing linearly with logarithm of frequency. 2. The lower limit shall apply at the transition frequencies. 10.3.Test Procedure (1) The EUT was placed on a non- metallic table, 80cm above the ground plane. (2) Setup the EUT and simulator as shown in 10.1 (3) The EUT Power connected to the power mains through a power adapter and a line impedance stabilization network (L.I.S.N1). The other peripheral devices power cord connected to the power mains through a line impedance stabilization network (L.I.S.N2), this provided a 50-ohm coupling impedance for the EUT (Please refer to the block diagram of the test setup and photographs). Both sides of power line were checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipments and all of the interface cables were changed according to ANSI C63.10 :2013on conducted Emission test. (4) The bandwidth of test Receiver is set at 10KHz. (5) The frequency range from 150 KHz to 30MHz is checked. 10.4.Test Result Pass Note: If peak Result comply with AV limit, QP and AV Result is deemed to comply with AV limit EUT LISN LISN PC System 80cm Receiver :50 Terminator 0.8m Page 72 of 88 Report No.: A2305205-C01-R01 Line: Page 73 of 88 Report No.: A2305205-C01-R01 Neutral: Remark: This report only shall the worst case mode for GFSK 2402MHz, and the power supply mode is DC 15V from adapter with AC 120V/60Hz Page 74 of 88 Report No.: A2305205-C01-R01 11. ANTENNA REQUIREMENTS 11.1.Limit For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section 15.247 (b), if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. 11.2.Result The EUT antenna is Internal Antenna. It c omplies with the standard requirement. Page 75 of 88 Report No.: A2305205-C01-R01 12. TEST SETUP PHOTO 12.1.Photos of Radiated Emission test Page 76 of 88 Report No.: A2305205-C01-R01 12.2.Photos of Conducted Emission test Page 77 of 88 Report No.: A2305205-C01-R01 13. EUT PHOTO Page 78 of 88 Report No.: A2305205-C01-R01 Page 79 of 88 Report No.: A2305205-C01-R01 Page 80 of 88 Report No.: A2305205-C01-R01 Page 81 of 88 Report No.: A2305205-C01-R01 Page 82 of 88 Report No.: A2305205-C01-R01 Page 83 of 88 Report No.: A2305205-C01-R01 Page 84 of 88 Report No.: A2305205-C01-R01 Page 85 of 88 Report No.: A2305205-C01-R01 Page 86 of 88 Report No.: A2305205-C01-R01 Page 87 of 88 Report No.: A2305205-C01-R01 BT ANT Page 88 of 88 Report No.: A2305205-C01-R01 -------END OF REPORT-------

Inverted F Antenna Specification Summary ITEM ANT SPEC Model Name 2.4G ANT Horizontal Vertical 2400MHz 2400MHz2500MHz2400MHz2400MHz 2500MHz Center Frequency -1.73 -0.84 -0.68 -6.15 -3.70 -2.32 MAX. Gain -0.68 Polarization Horizontal and Vertical Azimuth Beam Pattern Omni-directional Impedance 50 Ohm Antenna Length 38.20mm Manufacture ZHUHAI JIELI TECHNOLOGY CO.,LTD Antenna Photo & Length (mm) Horizontal: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -40 Scale: 5/div Gain(dB) Frequency (MHz) Max Min Avg 2400 -1.73178 -30.0815 -8.48713 2450 -0.845801 -38.5605 -7.88012 2500 -0.685586 -24.0318 -6.79139 Vertical: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -30 Scale: 5/div Gain(dB) Frequency (MHz) Max Min Avg 2400 -6.1530 -24.1420 -13.0295 2450 -3.7054 -26.5836 -10.6700 2500 -2.32122 -30.4301 -9.70536 ANT Test Labs：Attestation of Global Compliance Co., Ltd.

FCC ID: 2A6KK-S100 IC: 30008-S100 1.1. Photos of Radiated Emission test 1.2. Photos of Conducted Emission test