2A6P9-ADC930Dash camera

High-definition dashcam 1. Power socket 2. Rearview socket 3. In-car camera 4. Display area 5.SD card slot socket 6. Speaker 7. Front camera 2. The main functions are as follows： ① 3.2-inch full-view screen, IPS high-definition screen ② Front 4K(3840*2160)25fps+ rear 1080P 25fps+ interior 1080P 20fps ③ Supports Wi-Fi mobile phone interconnection function ④ Built-in G-SENSOR collision video locking function ⑤ Supports time-lapse video parking monitoring function ⑥ Supports GPS and ADAS functions ⑦ Supports up to 256G-TF cards ⑧ Supports OTA online upgrade when connected to WIFI 一、Installation Instructions Use a 12V to 5V voltage reduction cable. Connect the yellow power cord to the 12V power supply, the red ACC ignition control wire, and the black ground wire. Start the engine. The light will come on and be flashing. The machine starts and enters the video recording state. Or you can directly use a 12V to 5V step-down car charging cable. 1.Installation diagram of the voltage reduction line Figure 1 Wiring diagram Figure 2 Interior installation diagram 2.Schematic diagram of vehicle charger installation Figure 3 Schematic diagram of the vehicle charger Figure 4 Schematic diagram of vehicle charging 二、Download and install the APP 1. For the first time using the recorder, please scan the QR code below with your mobile phone to download the APP “GoLook”APP； 2. For iphones, you can search for "GoLook (or Luying)" in the Apple app store to download and install it. For Android phones, you can search for "GoLook (or Luying)" in the App Store to download and install it. 3. After starting the car and turning on the recorder to make it work, find the WIFI starting with "HisDvr_******" in the phone Settings and enter the default password 12345678 to connect. After the connection is completed, enter the APP. The time of the recorder will be synchronized with the current time on your phone. Additionally, you need to enter the recorder Settings option and select "Format SD Card". 1. Iii. Instructions for the Recorder 2. Description and explanation of key functions 3. Key function Quick function of the equipment "M key" Short press Menu Function/Return to Video Power button Short press Pause recording/Start recording Long press for 2 seconds Power off/Power on "Next key Short press Before and after switching. Internal video "Up key Short press Turn on recording/Turn off recording LCD menu function "M key" Short press Return Long press for 3 seconds Exit file management "Up key Short press Move left/up Down key Short press Move to the right/down Power button Short press Confirm to delete the file/confirm to lock the file ➢ 【M Key 】 Menu key/Back key Function 1: In the video recording mode; Press the [M key] briefly to enter the menu mode. Function 2: In the menu, briefly press the [M key] to return. In the file management mode, long press the [M key] for 3 seconds to exit file management. ➢ Flip up key/Play the previous video/recording to turn on/off Function 1: Page-flipping function In the menu Settings and playback mode, briefly pressing the "Up Key" activates the function of moving left or up. Function 2: Play the previous video In playback mode, during the video playback process, briefly press the [Up Key] to play the previous video. Function 3: In the video recording mode, briefly press the [Up Key] to turn off the recording, and briefly press it again to turn it on ➢ Power button/Video recording button/Confirm button Function 1: Power on/Off function When the machine is turned off, press and hold the [Power Button] for 2 seconds to turn on the power of this machine, and it will start working automatically. When the device is powered on, long press the [Power Button] and hold it for 2 seconds. The device will automatically save the video file and user Settings and then shut down. Function 2: In video recording mode, a short press can turn the recording on or off. Function 3: Briefly press "OK" on the menu page ➢ Scroll down/Play the next video/Turn WiFi on/off/Turn recording on/off Function 1: Page-flipping function. In the menu Settings and playback mode, briefly press the [Page-flipping Key] to move to the right or down Function 2: In playback mode, during the video playback process, briefly press the [Down Scroll Key] to play the next video. Function 3: In the video recording mode, briefly press the [Down Scroll Key] to switch between the front and rear camera views 2. Indicator light description Blue light Slow flash Video Chang Liang Not recorded Red light Flash The TF card is not inserted or the card is abnormal Chang Liang The TF card has been inserted Note: The red and blue lights are flashing rapidly simultaneously: The recorder device is upgrading its firmware 3.Description of the main functions of the APP Settings interface Recording switch On (default)/Off Time watermark On (default)/Off Video recording duration 1 minute (default)/2 minutes Speaker volume To adjust the playback volume of the recorder's speaker, you can choose off/low/medium (default)/high Emergency video trigger sensitivity The collision sensitivity adjustment during normal working video recording can be selected as off/low (default)/ high Vibration startup Parking monitoring switch on/off (default) Format the TF card Format the memory card (FAT32 64KB) Modify the Wi-Fi of the recorder Change the WIFI account/password (If you forget the WIFI password, you can long press the photo button to restore the factory Settings) factory data reset Reset Settings function (WiFi will also be restored to the default account and password) About the recorder Recorder firmware and APP information Dashcam ADAS refers to the application of Advanced Driver Assistance Systems in dashcams. ADAS utilizes a variety of sensors and algorithms to provide drivers with auxiliary functions for safe driving, helping them better perceive and respond to the road environment, thereby enhancing driving safety. The following are the main functions of the …

Text truncated - open the document above for the full version.

Rev 1/26/2023 (Promaster Electronic LLC) Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: February 5, 2026 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2A6P9-ADC930 [Promaster Electronic LLC] certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [Promaster Electronic LLC] certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, (Applicant signature) (Applicant printed name) Antonio Lopez Rev 1/26/2023 (Promaster Electronic LLC) Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: February 5, 2026 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2A6P9-ADC930 [Promaster Electronic LLC] certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Antonio Lopez

Promaster Electronic LLC U.S. Agent Letter of Attestation To: Federal Communications Commission 7435 Oakland Mills Road, Columbia, MD 21046, USA Date: February 6, 2026 Ref: Attestation Statement – Part 2.911(d)(7) filing FCC ID: 2A6P9-ADC930 Promaster Electronic LLC(“the applicant”) certifies that, as of the date of the filing of the application, Promaster Electronic LLC (“the agent”) is our designated U.S. agent for service of process for the above reference FCC ID. The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges it is our responsibility to inform the FCC whenever the agent information changes. Promaster Electronic LLC ("the agent) understand it is the agent's obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address. Designated U.S. Agent Company Name: Promaster Electronic LLC FRN: 0032356586 Address: 25275 Budde Rd, Suite 31, Spring, Texas, United States 77380 Signature: Contact Person: Antonio Lopez Tel: (832) 813-5123 Email: [email protected] Applicant Company Name: Promaster Electronic LLC FRN: 0032356586 Address: 25275 Budde Rd, Suite 31, Spring, Texas, United States 77380 Signature: Contact Person: Antonio Lopez Tel: (832) 813-5123 Email: [email protected]

2.4GHz 3216 Chip Antenna: HT-3216-M02 3216 Chip antenna For Bluetooth / WLAN Applicationsd P/N: 1.66士0.20 1.23士0.20 Shenzhen Hetuo Technology Co.,Ltd. Address: Room 1202B, Comprehensive Building, Building C6, Hengfeng Industrial City, No. 739 Zhoushi Road, Hezhou Community, Hangcheng Street, Bao'an District, Shenzhen City 18665849001/18665934465 第1页共10页 忆 2.4GHz 3216 Chip Antenna: HT-3216-M02 忆 Part Number Information HT 3216 —— A B F 垄 G- D E F A Product Series Antenna B Dimension L x W 3.2Xl.6mm (+-0.2mm) C Material High K 、material D Working Frequency 2.4 ~ 2.5GHz E Feeding mode Monopole & Single Feeding F Antenna type ＼ ，， 八 一． T ype =02 1. Electrical Specification Central Frequency 2450 MHz Bandwidth ）） 100 (Min. ) MHz Return Loss -6.5 (Max) dB Peak Gain 2.71 dBi Impedance 50 Ohm Operating Temperature -40 ~ +85 o c Maximum Power 4 w Resistance to Soldering Heats 10 (@ 260 ° () sec. Polarization Linear Azimuth Beamwidth Omni-directional Termination Cu/ Sn (Leadless) Remark: Bandwidth & Peak Gain was measured under evaluation board of next page 深圳市合拓科技有限公司 Shenzhen Hetuo Technology Co.,Ltd. 第2页共10页 18665849001 / 1 8665934465 2.4GHz 3216 Chip Antenna: HT-3216-M02 忆 2. Recommended PCB Pattern Evaluation Board Dimension ....... . . ... ...... ． ． ．．． ．． ．． ． ． ．． ．． ．． ．．． ．．．．．．． ．．． ．．．．．．． ．． ．． ．． ．． ．． ．． ．． •••••••• . ) ·· ········· · • ••••••••• ．． ．．． ．．．． ． ．．．．． ．． ．．． ......... .......... ．． ．．．．． ．． ．．． ． ． ． ． ． ．．．．． ......... .......... ．． ．．．．． ．． ．．． ．． ．．． ．．．．． . . .... ．． ．． ．．． ．．．．． ．． ．．． ．．．．． ........ ．． ．． ．．． ．． ． ．． ．．．．． ．． ．．． ． ．． ．． ．．． ．． ．．． ．．．．． ．．．．． ....... 40.0001 TOP Copper Unit: mm 仁二］ VIA Suggested Matching Circuit 1.1 nH Feeding 1 . DpF 深圳市合拓科技有限公司 Shenzhen Hetuo Technology Co.,Ltd. 第3页共10页 18665849001 / 18665934465 2.4GHz 3216 Chip Antenna: HT-3216-M02 Layout Dimensions in Clearance area1Size=S.2*5.0mm1 50 ohm transmission Line 5 '. 000( 29000l j ootPrint (Unit : mm) 丁 2.6000酝I 11.6000 � 1.2000 t--。，7 000 七—叫 深圳市合拓科技有限公司 Shenzhen Hetuo Technology Co.,Ltd. 18665849001 / 18665934465 第4页共10页 忆 2.4GHz 3216 Chip Antenna: HT-3216-M02 3. Measurement Results Return Loss Trc1国王IdB Mag 10 dB/ RefO dB Cal 至 卜 — 20 卜 — 10 � -10 —~ � -20 ＼／ � -30 � -40 尸－50 尸－60 深圳市合拓科技有限公司 1 2 • 3 E/ 2.40 0000 GI -lz -10. 2.45 booo GI -lz -20. 2.50 0000 GI -lz -11. Shenzhen Hetuo Technology Co.,Ltd. 18665849001/18665934465 第5页共10页 让 1 D70 dB 1267 dB D39 dB - 2.4GHz 3216 Chip Antenna: HT-3216-M02 忆 Radiation Pattern ｀｀ 42 . L - 2 (ESP) 』 0兰Od x 」 Y Z 了 ． 一一一一一． 一一一一 一 •-- - --· - － － － -· ＿ ＿ ＿ ＿, _ ＿ ＿ ＿, - － － － －. 4 - 6 3 -1 0 -1 2 - 1 4 l 1 } 尸 Efficiency Peak Gain Directivity 2400MHz , 55.21 % 1.45 dBi 5.32 dBi 2450MHz 66.45 % 2.71 dBi 5.21 dBi 2500MHz 57.53 % 1.98 dBi 5.29 dBi Chamber Coordinate System 深圳市合拓科技有限公司 Shenzhen Hetuo Technology Co.,Ltd. 第6页共10页 18665849001 / 1 8665934465 2.4GHz 3216 Chip Antenna: HT-3216-M02 忆 ZJXY DUT Turning Support 4.Reliabilitv and Test Condictions ITEM Solderab小ty Solder heat Resistance Component Adhesion (Push test) Component Adhesion (Pull test) REQUIREMENTS 1.Wetting shall exceed 90% coverage 2.No visible mechanical damage TEMP ( ° C) 『 一 230 ° ( 150 ° 1.No visible mechanical damage 2.Central Freq. change :within土6% 260 ° C 1 50 ° C 1.No visible mechanical damage 1.No visible mechanical damage 深圳市合拓科技有限公司 TEST CONDITION Pre-heating temperature:150 ° C/60sec Sp ider temperature:230土5 ° C Duration:4士1sec 、 Solder:Sn-Ag3.0-Cu0.5 Flux for lead free: rosin Pre-heating temperature:150 ° C/60sec Solder temperature:260土5 ° C Duration:10士0.5sec Solder:Sn-Ag3.0-Cu0.5 Flux for lead free: rosin The device should be reflow soldered(230士5 ° C for 10sec.) to a tinned copper substrate A dynometer force gauge should be applied the side of the component. The device must with-ST-F 0.5 Kg without failure of the termination attached to component Insert 10cm wire into the remaining open eye bend,the ends of even wire lengths upward and wind together Terminal shall not be remarkably damaged Shenzhen Hetuo Technology Co.,Ltd. 18665849001/18665934465 第7页共10页 2.4GHz 3216 Chip Antenna: HT-3216-M02 忆 Thermal shock 1. No visible mechanical damage ±e:::o 2 +85±5 ° ( ＿ Room Temperature 圣 Within 3sec +85 ° (=>30土3m1n -40 ° (=>30土3min Test cycle:10 cycles The chip shall be stab小zedat normal condition for 2-3 hours before measuring 3-4 -40±2 ° ( ＿ Room Temperature 30±3 ＿ Within 3sec Resistance to High Temperature 1. No visible mechanical damage 2. Central Freq. change :within土6% 3. No disconnection or short circu仆 Resistance to Low Temperature 1. No visible mechanical damage 2. Central Freq. change :within土6% 3. No disconnection or short circu仆 Hum昢ty 1. No visible mechanical damage ， 2. Central Freq. change :within土6% 3. No disconnection or short circu仆 5.Soldering and Mounting Temperature: 85土5 ° C Duration: 1000土12hrs The chip shall be stab小zedat normal condition for 2-3 hours before measuring Temperature:-40土5 ° C Duration: 1000土12hrs The chip shall be stab小zedat normal condition for 2-3 hours before measuring Tem·perature: . 40土2 ° c ， Hum昢ty:90% to 95% RH Duration: 1000土12hrs The chip shall be stab小zedat normal condition for 2-3 hours before measuring Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansLon between solder, chip and substrate. The terminations are suitable for all wave and re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air soldering tools. Reflow Soldering Iron Soldering SOLDERING 10s max NATURAL COOLING SOLDERING within 3s NATURAL COOLING (0°)W正nLV丘wdWWL 6°)3�nl\1�3dml TIME(sec.) TIME(sec.) Recommended temperature profiles for re-flow soldering in Figure 1. Products attachment with a soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be emploved the following precautions are recommended. 深圳市合拓科技有限公司 Shen…

Text truncated - open the document above for the full version.

Promaster Electronic LLC Date: February 5, 2026 Product Model Number: ADC-930, ADC-931, ADC-932, G930, G931, G932, D4 FCC ID: 2A6P9-ADC930 To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following: • Testing • Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. Signature： By: Antonio Lopez Title: President Email: [email protected] Telephone: (832) 813-5123 On behalf of: Promaster Electronic LLC

Promaster Electronic LLC Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: February 5, 2026 Subject; Request for Confidentiality FCC ID: 2A6P9-ADC930 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements for UNII devices In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: By: Antonio Lopez Title: President

Promaster Electronic LLC Model Difference Statement Dear Sir/Madam, FCC ID: 2A6P9-ADC930 Date: February 6, 2026 Added models ADC-931, ADC-932, G930, G931, G932, D4 basis of the original product ADC-930 The color of appearance and model name of series models listed are different from the main model, but the circuit and the electronic construction are the same, declared by the manufacturer. Sincerely, Signature： By: Antonio Lopez Title: President Email: [email protected] Telephone: (832) 813-5123 On behalf of: Promaster Electronic LLC

Report No: SSP26010304-1E FCC ID: 2A6P9-ADC930 Annex of Test Report Annex A. EUT External Photos Model: ADC-930 EUT View 1 EUT View 2 Report No: SSP26010304-1E FCC ID: 2A6P9-ADC930 Annex of Test Report EUT View 3 EUT View 4 Report No: SSP26010304-1E FCC ID: 2A6P9-ADC930 Annex of Test Report EUT View 5 EUT View 6 Report No: SSP26010304-1E FCC ID: 2A6P9-ADC930 Annex of Test Report EUT View 7

Report No: SSP26010304-1E FCC ID: 2A6P9-ADC930 Annex of Test Report Annex D. Label and Information FCC Label Sample Label Size : 3cm * 1.5cm FCC Label Specifications Text is Black in color and is justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Where the EUT is constructed in two or more sections connected by wires and marketed together, the above statement is required to be affixed only to the main control unit. When the EUT is so small or for such use that it is not practicable to place the statement on it, the above information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. FCC Label Location

Report No: SSP26010304-1E FCC ID: 2A6P9-ADC930 Annex of Test Report Annex B. EUT Internal Photos EUT Internal View 1 EUT Internal View 2 Report No: SSP26010304-1E FCC ID: 2A6P9-ADC930 Annex of Test Report EUT Internal View 3 EUT Internal View 4 Report No: SSP26010304-1E FCC ID: 2A6P9-ADC930 Annex of Test Report EUT Internal View 5 EUT Internal View 6 Report No: SSP26010304-1E FCC ID: 2A6P9-ADC930 Annex of Test Report EUT Internal View 7 EUT Internal View 8 SMD ANT Report No: SSP26010304-1E FCC ID: 2A6P9-ADC930 Annex of Test Report EUT Internal View 9 EUT Internal View 10 GPS ANT Report No: SSP26010304-1E FCC ID: 2A6P9-ADC930 Annex of Test Report EUT Internal View 11 EUT Internal View 12

FCC ID: 2A6P9-ADC930 RF Exposure Evaluation Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm2) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3–3.0 614 1.63 *(100) 6 3.0–30 1842/f 4.89/f *(900/f2) 6 30–300 61.4 0.163 1.0 6 300–1500 f/300 6 1500–100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f2) 30 30–300 27.5 0.073 0.2 30 300–1500 f/1500 30 1500–100,000 1.0 30 f = frequency in MHz Friis transmission formula: Pd = (Pout*G)/(4*pi*r2) Where Pd = power density in mW/cm2, Pout = output power to antenna in mW; G = gain of antenna in linear scale, Pi = 3.1416; R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm2. If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. Test Result of RF Exposure Evaluation 2.4G Wi-Fi Mode Output power to antenna (dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result 802.11b 13.58 46.77 0.0085 1.0 PASS Remark: 2.4G antenna gain=2.71dBi

Report No: SSP26010304-1E FCC Test Report Page 1 of 46 FCC TEST REPORT FCC ID: 2A6P9-ADC930 Report No. : SSP26010304-1E Applicant : Promaster Electronic LLC Product Name : Dash camera Model Name : ADC-930 Test Standard : FCC Part 15.247 Date of Issue : 2026-01-23 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.ccuttest.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: SSP26010304-1E FCC Test Report Page 2 of 46 Test Report Basic Information Applicant..................................: Promaster Electronic LLC Address of Applicant...............: 25275 Budde Rd, Suite 31, Spring, Texas, United States 77380 Manufacturer..........................: Guangdong zhonglian Mobile Technology Co., Ltd. Address of Manufacturer........: No. 602-B1, 6th Floor, Building 3, Liandong U Valley, No. 1 Shuiqing Road, Shuikou Sub-district, Huicheng District, Huizhou City Product Name.........................: Dash camera Brand Name.............................: Autosky Main Model..............................: ADC-930 Series Models..........................: ADC-931, ADC-932, G930, G931, G932, D4 Test Standard..........................: FCC Part 15 Subpart C KDB 558074 D01 15.247 Meas Guidance v05r02 ANSI C63.4-2014 ANSI C63.10-2020 + COR.1-2023 Date of Test .............................: 2026-01-13 to 2026-01-15 Test Result...............................: PASS Tested By ................................: (Colin Chen) Reviewed By............................: (Lorzix Luo) Authorized Signatory............: (Lahm Peng) Note : This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd.. All test data presented in this test report is only applicable to presented test sample. Report No: SSP26010304-1E FCC Test Report Page 3 of 46 CONTENTS 1. General Information ....................................................................................................................................................5 1.1 Product Information .............................................................................................................................................5 1.2 Test Setup Information..........................................................................................................................................6 1.3 Compliance Standards ...........................................................................................................................................7 1.4 Test Facilities ........................................................................................................................................................7 1.5 List of Measurement Instruments ..........................................................................................................................8 1.6 Measurement Uncertainty .....................................................................................................................................9 2. Summary of Test Results ........................................................................................................................................... 10 3. Antenna Requirement ............................................................................................................................................... 11 3.1 Standard and Limit.............................................................................................................................................. 11 3.2 Test Result .......................................................................................................................................................... 11 4. Conducted Emissions ................................................................................................................................................ 12 4.1 Standard and Limit.............................................................................................................................................. 12 4.2 Test Procedure.................................................................................................................................................... 12 4.3 Test Data and Results .......................................................................................................................................... 13 5. Radiated Emissions ................................................................................................................................................... 14 5.1 Standard and Limit.............................................................................................................................................. 14 5.2 Test Procedure.................................................................................................................................................... 14 5.3 Test Data and Results .......................................................................................................................................... 16 6. Band-edge Emissions(Radiated) ............................................................................................................................... 20 6.1 Standard and Limit.............................................................................................................................................. 20 6.2 Test Procedure.................................................................................................................................................... 20 6.3 Test Data and Results ...............................................................................................................…

Text truncated - open the document above for the full version.

Report No: SSP26010304-1E FCC ID: 2A6P9-ADC930 Annex of Test Report Annex C. Test Photos Radiated Emission Test View Below 1GHz Radiated Emission Test View Above 1GHz