2A6XTANC-007Wireless Bluetooth Headphone

Hd sound quality Bluetooth noise-cancelling headphones The instructions ANC-007 stereo sound voice calling 正面 反面 Operation long press the power button 2S, and the blue light will be on1. Power on: when the power on sound is heard; long press the power button 6s, the red light will be on for 1s,Power off: then the red and blue lights will be off. long press the power button 4S, the red and blue2. Bluetooth pairing: lights flash alternately, the bluetooth is switched on to enter the pairing state, and the mobile phone searches for the Bluetooth device "AH-007" and connects the pairing. Short press the power button;3. Answer/hang up: long press the power button 2s;4. Reject: long press the power key 4S5. Voice call: short press the power button;6. Play/pause: short press -/+ button to control the volume;7. Volume increase or decrease: long press -/+ button to control up/down music;8. Up/down music: 9. Double-click the power button to redial the last broadcast number Product features Support for voice calls Support phone answer/hang up/refuse/redial Support wireless stereo music Support music play/pause/volume up/volume down Product Specification V4.0Bluetooth version: HSP V1.2,HFP V1.6,A2DP V1.2,Bluetooth protocol support: AVRCP V1.4 2402MHz-2480MHzFrequency range: 10MTransmission distance: -80dbmSensitivity: 3.7VWorking voltage: 450mAhBattery capacity: ANC- OFF 10H, ANC-ON 9HMusic listening time: 14HTalk time: 200HStandby time: 3HCharging time: Matters needing attention A. Do not disassemble, repair or modify the product by yourself; B. Please store and use the product in room temperature environment; C. Do not drop the product to avoid damage caused by falling; D. Please use the rated voltage of the headset for charging; E. Unauthorized disassembly will invalidate the warranty; F. Prolonged exposure to high volume may cause hearing damage, so excessive volume should be avoided; 此处需 对折 FCC warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the device and receiver. --Connect the device into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment

Dongguan City Shengqiang Electronics Co., Ltd Statement We Dongguan City Shengqiang Electronics Co., Ltd Hereby Declare that The product Wireless Bluetooth Headphone, models no. ANC-007 and ANC-001 are all identical in interior structure, electrical circuits and components, and just the appearance are different for the marketing requirement. Your assistance on this matter is highly appreciated. Yours sincerely, Signature： Name：WEN WU DENG Title：Manager

November 01, 2022 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen Timeway Testing Laboratories/ Zone C, 1st Floor, Zone C, 1st Floor, Block B, Jun Xiang Da Building, Zhongshan Park Road West, Tong Le Village, Nanshan District, Shenzhen, China (Name of Agent company name and address) to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Dongguan City Shengqiang Electronics Co., Ltd / Shijiezhen sijiaxihegongyequ dongguanshi guangdongsheng 523290 <Signature>： Name：WEN WU DENG Title：Manager Applicant Company：Dongguan City Shengqiang Electronics Co., Ltd

November 01, 2022 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2A6XTANC-007 Product Name: Wireless Bluetooth Headphone Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: • Schematics • Block diagram • Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature>： Name：WEN WU DENG Title：Manager Applicant Company：Dongguan City Shengqiang Electronics Co., Ltd

Inverted F Antenna Specification Summary ITEMANT SPEC Model Name 2.4G ANT HorizontalVertical 2400MHz 2400MHz2500MHz2400MHz2400MHz 2500MHz Center Frequency -1.26-0.76-0.58-5.25-2.46-1.86 MAX. Gain -0.58dBi PolarizationHorizontal and Vertical Azimuth Beam Pattern Omni-directional Impedance50 Ohm Antenna Length 38.20mm Manufacture ZHUHAI JIELI TECHNOLOGY CO.,LTD Antenna Photo & Length (mm) Horizontal: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -40 Scale: 5/div Gain(dB) Frequency (MHz) Max Min Avg 2400 -1.26174 -30.0801 -7.18716 2450 -0.765802 -36.5604 -7.48023 2500 -0.585582 -22.0315 -6.59127 Vertical: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -30 Scale: 5/div Gain(dB) Frequency (MHz) Max Min Avg 2400 -5.2537 -22.1424 -12.4294 2450 -2.4652 -24.5837 -10.4702 2500 -1.86120 -29.5214 -9.20432 ANT Test Labs：Attestation of Global Compliance Co., Ltd.

Model: ANC-007 Model: ANC-007 Model: ANC-007 Model: ANC-001 Model: ANC-001 Model: ANC-001

Wireless Bluetooth Headphone Model No.: ANC-007 Trade Name: AUOUA FCC ID: 2A6XTANC-007

Label Location

Inside view

Acc eir whe pt gt E = d = Sop Ant Fie So <2 . The ording to p = pt x re: = transmi = numeri c = electric = measurem t = (EXd) t gain = eld stre Pt={ [1 .786 mW n SAR eva o 447498 D gt = (EXd tter outp c gain of c field st ment dista 2 /30 x gt =-0.58dBi ngth =96 0 (96.89/20) aluation i RF Expo D04 Interi d) 2 /30 put power the tran s trength in ance in me i so Ant 6.89dBμV /10 6 x3 s not req osure eval im General in watts, smitting a n V/m, --- eters (m)- t numeri V/m @3m@2 3] 2 /30x0. quired luation l RF Expos antenna (u - 10 ((dBuV ---3m ic gain= 2402MHz .875}x100 sure Guida unitless), V/m)/20) /10 6 0.875 00 mW = ance v01 1.675mW

Report No.: TW2205221E File reference No.: 2022-05-25 Applicant: Dongguan City Shengqiang Electronics Co., Ltd Product: Wireless Bluetooth Headphone Model No.: ANC-007, ANC-001 Trademark: Test Standards: FCC Part 15.249 Test result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.10 & FCC Part 15 Subpart C, Paragraph 15.249 regulations for the evaluation of electromagnetic compatibility Approved By Terry Tang Manager Dated: May 25, 2022 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TESTING LABORATORIES Zone C, 1st Floor, Block B, Jun Xiang Da Building, Zhongshan Park Road West, Tong Le Village, Nanshan District, Shenzhen, China Tel (755) 83448688, Fax (755) 83442996, E-Mail:[email protected] Report No.: TW2205221E Page 2 of 49 Date: 2022-05-25 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Special Statement： The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19. The testing quality system of our laboratory meet with ISO/IEC-17025 requirements, which is approved by CNAS. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAS-LAB Code: L2292 The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:2017 General Requirements) for the Competence of testing Laboratories. FCC-Registration No.: 744189 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 744189. Industry Canada (IC) —Registration No.:5205A The EMC Laboratory has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 5205A. A2LA (Certification Number:5013.01) The EMC Laboratory has been accredited by the American Association for Laboratory Accreditation (A2LA). Certification Number:5013.01 Report No.: TW2205221E Page 3 of 49 Date: 2022-05-25 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Test Report Conclusion Content 1.0 General Details ............................................................................................. 4 1.1 Test Lab Details............................................................................................. 4 1.2 Applicant Details.............................................................................................. 4 1.3 Description of EUT .......................................................................................... 4 1.4 Submitted Sample............................................................................................. 4 1.5 Test Duration................................................................................................... 5 1.6 Test Uncertainty................................................................................................ 5 1.7 Test By......................................................................................................... 5 2.0 List of Measurement Equipment......................................................................... 6 3.0 Technical Details.......................................................................................... 7 3.1 Summary of Test Results.................................................................................... 7 3.2 Test Standards................................................................................................. 7 4.0 EUT Modification............................................................................................. 7 5.0 Power Line Conducted Emission Test..................................................................... 8 5.1 Schematics of the Test....................................................................................... 8 5.2 Test Method and Test Procedure............................................................................ 8 5.3 Configuration of the EUT................................................................................. 8 5.4 EU…

Text truncated - open the document above for the full version.

Conducted Emission Test Setup: Conducted Emission Test Setup: