2A6XTBL-005Wireless Headphone

BT WIRELESS HEADPHONES USER MANUAL MODEL: BL-005 BL-005 4.0 10 meters specifications. Customer Name Customer Address Product Name Purchase Date Contacts Telephone Number Product Model Serial Number 1 23 BL-005说明书 备注：双面印刷，2折页 103.00 mm 146.00 mm TURNABLE DESIGN Power on/off: Long pressing the“ ”power on/off button to turn on/off the headphones. Bluetooth Pairing: Turn on the Bluetooth function on the Bluetooth devices, then pressing the “ ” power on button about 5 seconds until the blue and red LED light flashing together to pair the Bluetooth devices with pairing name "BL-005" successfully. Play/Pause: Short pressing “ ” power on/off button to play and pause music. Answer/End calls: Short pressing“ ”power on/off button to answer and end phone calls. Recent Calling: When get paired with smart phones, short pressing the“ ” power on/off button two time continuously, it would dial the calling from your most recent phone address lists. Volume Up/Down: Long pressing the Volume“ ”button to turn up/down volume. Previous Song: Short pressing the Volume“ ”button to switch to the previous song when music playing. Next Song: Short pressing the Volume“ ”button to switch to the next songs when music playing. Wired Audio: Plug the 3.5mm audio cable to audio line to hole as a wired headphones using. Charging: With the Micro USB cables for charging, then the Red LED indicator would on automatically. Reminds: Please kindly turn off it when not using to saving powers, Be caution of during charging!!! This BL-005 Bluetooth Wireless Headphones has a full 12 months replacement warranty and Battery is only 6 months. Conditions apply. For more details, please visit our website www.aesonic.com against manufacturing defects starting from the purchase date. 正面 反面 FCC warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the device and receiver. --Connect the device into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment

Dongguan City Shengqiang Electronics Co., Ltd Statement We Dongguan City Shengqiang Electronics Co., Ltd Hereby Declare that The product Wireless Headphone, models no. BL-005, BL-003, BL-006 are all identical in interior structure, electrical circuits and components, and just the appearance is different for the marketing requirement. Your assistance on this matter is highly appreciated. Yours sincerely, <Signature>： Name：DENG WEN WU Title：Manager

July 12, 2022 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen Timeway Testing Laboratories/ Zone C, 1st Floor, Zone C, 1st Floor, Block B, Jun Xiang Da Building, Zhongshan Park Road West, Tong Le Village, Nanshan District, Shenzhen, China (Name of Agent company name and address) to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Dongguan City Shengqiang Electronics Co., Ltd / Xihe Industrial, Sijia, Shijie Town, Dongguan City <Signature>： Name：DENG WEN WU Title：Manager Applicant Company：Dongguan City Shengqiang Electronics Co., Ltd

July 12, 2022 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2A6XTBL-005 Product Name: Wireless Headphone Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: • Schematics • Block diagram • Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature>： Name：DENG WEN WU Title：Manager Applicant Company：Dongguan City Shengqiang Electronics Co., Ltd

BL-005 BL-003 BL-006

FCC ID: 2A6XTBL-005

Acc eir whe pt gt E = d = Sop Ant Fie So <2. The ording to p = pt x re: = transmi = numeri c = electric = measurem t = (EXd) t gain = eld stre Pt={ [1 0 .79 mW n SAR eva o 447498 D gt = (EXd tter outp c gain of c field st ment dista 2 /30 x gt =-0.58dBi ngth =90 0 (90.25/20) aluation i RF Expo D04 Interi d) 2 /30 put power the tran s trength in ance in me i so Ant 0.25dBμV /10 6 x3 s not req osure eval im General in watts, smitting a n V/m, --- eters (m)- t numeri V/m @3m@2 ] 2 /（30x0 quired luation l RF Expos antenna (u - 10 ((dBuV ---3m ic gain= 2402MHz 0.875）} sure Guida unitless), V/m)/20) /10 6 0.875 x1000 mW ance v01 W = 0.363mW

Report No.: TW2206380-01E File reference No.: 2022-07-11 Applicant: Dongguan City Shengqiang Electronics Co., Ltd Product: Wireless Headphone Model No.: BL-005, BL-003, BL-006 Trademark: Test Standards: FCC Part 15.249 Test result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.10 & FCC Part 15 Subpart C, Paragraph 15.249 regulations for the evaluation of electromagnetic compatibility Approved By Terry Tang Manager Dated: July 11, 2022 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TESTING LABORATORIES Zone C, 1st Floor, Block B, Jun Xiang Da Building, Zhongshan Park Road West, Tong Le Village, Nanshan District, Shenzhen, China Tel (755) 83448688, Fax (755) 83442996, E-Mail: [email protected] Report No.: TW2206380-01E Page 2 of 51 Date: 2022-07-11 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Special Statement： The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19. The testing quality system of our laboratory meet with ISO/IEC-17025 requirements, which is approved by CNAS. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAS-LAB Code: L2292 The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:2017 General Requirements) for the Competence of testing Laboratories. FCC-Registration No.: 744189 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 744189. Industry Canada (IC) —Registration No.:5205A The EMC Laboratory has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 5205A. A2LA (Certification Number:5013.01) The EMC Laboratory has been accredited by the American Association for Laboratory Accreditation (A2LA). Certification Number:5013.01 Report No.: TW2206380-01E Page 3 of 51 Date: 2022-07-11 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Test Report Conclusion Content 1.0 General Details ............................................................................................... 4 1.1 Test Lab Details................................................................................................ 4 1.2 Applicant Details.............................................................................................. 4 1.3 Description of EUT .......................................................................................... 4 1.4 Submitted Sample............................................................................................. 4 1.5 Test Duration................................................................................................... 5 1.6 Test Uncertainty................................................................................................ 5 1.7 Test By......................................................................................................... 5 2.0 List of Measurement Equipment......................................................................... 6 3.0 Technical Details............................................................................................. 7 3.1 Summary of Test Results.................................................................................... 7 3.2 Test Standards................................................................................................. 7 4.0 EUT Modification............................................................................................. 7 5.0 Power Line Conducted Emission Test..................................................................... 8 5.1 Schematics of the Test....................................................................................... 8 5.2 Test Method and Test Procedure............................................................................ 8 5.3 Configuration of the EUT...........................................................................…

Text truncated - open the document above for the full version.

Conducted Emission Test Setup: Radiated Emission Test Setup: