2A73O-FFP02Solar Bird Bath Fountain Pump

User Manual Model name: Solar Bird Bath fountain pump Model number: FFP02 Instruction manual Product Introduction: (Line chart marks name) • Nozzle installation diagram: (Mark: vertical insertion) • Product usage: 1. Place the product on the water surface of the bird bath or pond without obvious incline (incline <6 after air exhaust). The water surface should be submerged in the machine box, and the water pump should start to work when the light intensity meets the working requirements of the water pump. (1) When the light intensity is greater than 8500LUX, the fountain will work normally; When the light intensity is greater than 27,000 LUX, the fountain sprays water at the same time the battery starts charging, and the spray height is 30~60 (cm). (2) When the light intensity is between 500Lux and 8000 LUX, the pump will work intermittently. (3) When the light intensity is less than 240LUX, the fountain will switch to night mode, the water pump will spray water stably, and the LED will light up in a colorful gradient. When the battery power is sufficient, it will be put to sleep after working for 4 hours. (4) The fountain is equipped with water shortage protection function. When the fountain leaves the water, the pump will stop working. 2. Different fountain effects can be achieved through different sprinkler heads. 3. Small stones can be loaded into the counterweight net bag, and the counterweight bag is suspended in a fixed position at the lower part of the pump 4. Supplement Cleaning and maintenance: 1. It is recommended to clean the surface of the solar water pump every week. Dust and impurities may affect the working efficiency of the solar cells. 2. After a period of use, the panel will accumulate scale, affecting the working efficiency of solar cells. You can use citric acid, vinegar or scale remover mixed with tap water for scale cleaning. Rinse with tap water after cleaning to avoid contamination of water quality by residual substances. 3. Impurities and algae in the water environment may block the front filter cotton of the water pump. Use a screwdriver to remove the water inlet protection cover. Take out the pre-filter cotton and clean it, and then reinstall it. 4. If abnormal water flow is found in the sprinkler head, remove the sprinkler head for cleaning. Because the size of the nozzle hole is small, sharp tools can be used to dredge the blockage. Cleaning and maintenance: FAQ: 1. Can the solar water pump work on cloudy days or under shade? Solar cells need bright light to generate enough power, so they need to be in a bright place. The remote version can be charged by a polymer battery to help the pump work in low-light conditions. For details, refer to the product instructions. 2. Will water scarcity damage the water pump? No, the pump has the function of water protection, water shortage will stop automatically. The work can resume after being placed in water again. 3. How many hours can I work at night? During the day, when the polymer battery is full and the light is bright, it can work for four hours. 4. How to adjust the water flow if it is too big or too small? Different nozzle can be used to achieve different fountain effects, remote control version can be controlled by remote control water flow size. Basic parameter information： 1. Host weight: 500g 2. Pump voltage: DC8V head: 75CM 3. Polymer battery capacity: 7.4V 1000mA/h 4. Solar cell: 4W 8V (test condition: incandescent 38000LUX). 5. The solar fountain is 10-60CM high. Remote controller function description *Only compatible with the remote controller pump version Light color adjustment Light mode switch Light brightness(+) Water pump pressure (+) Light on/off Light brightness(-) Water pump pressure (-) Water pump on/off FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. FCC Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

1/1 US Agent for Service of Process LETTER OF ATTESTATION TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process: Company Name: FCC US Agent, LLC FRN: 0033402884 Contact Name: Tim Payne Address: 3722 Illionis Avenue, Saint Charles, IL, 60174, USA Telephone No: 708-571-3148 Email: Support@FCCUSAgent. com Applicant: Company name: FOOFEE intelligent manufacturing Technology (dongguan) Co., Ltd. Product Description: Solar Bird Bath Fountain Pump Grantee code: 2A73O FCC ID: 2A73O-FFP02 Contact Name: Jie Li Address: Room 401, Building 15, No.1 Pushi First Road Qiaotou Town, Dongguan City, Guangdong Province Telephone No: 13816419171 Email: [email protected] [FOOFEE intelligent manufacturing Technology (dongguan) Co., Ltd.] certifies that, as of the date of this filing of the application with the TCB, [FCC US Agent, LLC] is our designated US agent for service of process for the above referenced FCC ID. [FOOFEE intelligent manufacturing Technology (dongguan) Co., Ltd.] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [FCC US Agent, LLC] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. Date: 2023/05/12 Applicant’s Name: Jie Li US Agent’s Name: Tim Payne Title: corporate representative Title: Manager Signature Signature

C5266091_X24_Ed.2 1/1 “Attestation Statements” TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: FOOFEE intelligent manufacturing Technology (dongguan) Co., Ltd. Grantee code: 2A73O FCC ID: 2A73O-FFP02 Contact Name: Jie Li Address: Room 401, Building 15, No.1 Pushi First Road Qiaotou Town, Dongguan City, Guangdong Province Telephone No: 13816419171 Fax No: 13816419171 Email: [email protected] i. [FOOFEE intelligent manufacturing Technology (dongguan) Co., Ltd. ] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [FOOFEE intelligent manufacturing Technology (dongguan) Co., Ltd. ] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. [FOOFEE intelligent manufacturing Technology (dongguan) Co., Ltd. ] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing “covered” equipment. Date: 2023-05-09 Applicant’s Name: Jie Li Title: corporate representative Signature 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist

FCC ID: 2A73O-FFP02 External photos FCC ID: 2A73O-FFP02 FCC ID: 2A73O-FFP02 FCC ID: 2A73O-FFP02

FCC ID: 2A73O-FFP02 Internal photos FCC ID: 2A73O-FFP02 FCC ID: 2A73O-FFP02 RF Antenna RF Chip

Report No.: NTC2304142F01 Dongguan Nore Testing Center Co., Ltd. Address: Building D, Gaosheng Science and Technology park, Hongtu road, Nancheng district, Dongguan city, Guangdong province, China Web: www.ntc-c.com Tel:+86-769-2202 2444 Fax:+86-769-2202 2799 Page 1 of 10 RF EVALUATION TEST REPORT Applicant/ Manufacturer....... : FOOFEE intelligent manufacturing Technology (dongguan) Co., Ltd. Address........................... : Room 401, Building 15, No.1 Pushi First Road, Qiaotou Town, Dongguan City, Guangdong Province, China Manufacturer.................... : FOOFEE intelligent manufacturing Technology (dongguan) Co., Ltd. Address........................... : Room 401, Building 15, No.1 Pushi First Road, Qiaotou Town, Dongguan City, Guangdong Province, China Factory........................... : FOOFEE intelligent manufacturing Technology (dongguan) Co., Ltd. Address.......................... : Room 401, Building 15, No.1 Pushi First Road, Qiaotou Town, Dongguan City, Guangdong Province, China Product Name................... : Solar Bird Bath Fountain Pump Brand Name..................... : ERAARK Model No. ....................... : FFP02 FCC ID........................... : 2A73O-FFP02 Measurement Standard....... : 47 CFR PART 2, Section 2.1093 Receipt Date of Samples.... : April 11, 2023 Date of Tested.................. : April 11, 2023 to May 08, 2023 Date of Report.................. : May 10, 2023 This report shows that above equipment is technically compliant with the requirements of the standards above. All test results in this report apply only to the tested sample(s). Without prior written approval of Dongguan Nore Testing Center Co., Ltd, this report shall not be reproduced except in full. Prepared by Rose Hu / Project Engineer Approved by Iori Fan / Authorized Signatory Report No.: NTC2304142F01 Page 2 of 10 Table of Contents 1. General Description of EUT ................................................................................................................................ 4 2. Test Facility and Location ................................................................................................................................... 6 3. Applicable Standards and References ................................................................................................................ 7 4. Maximum Permissible Exposure Limit ................................................................................................................ 8 5. RF Exposure Evaluation Results ...................................................................................................................... 10 Report No.: NTC2304142F01 Page 3 of 10 Revision History Report Number Description Issued Date NTC2304142F01 Initial Issue 2023-05-10 Report No.: NTC2304142F01 Page 4 of 10 1. General Description of EUT Product Information Product name: Solar Bird Bath Fountain Pump Main Model Name: FFP02 Additional Model Name: N/A Model Difference: N/A S/N: 2304-1847 Brand Name: ERAARK Hardware version: FF-P02_V1.0 Software version: HZ1226-12 Rating: DC 1.5V AAA battery* 2 Typical arrangement: Table-top I/O Port: N/A Accessories Information Adapter: N/A Cable: N/A Other: N/A Additional information Note: N/A Remark: All the information above are provided by the manufacturer. More detailed feature of the EUT please refers to the user manual. Report No.: NTC2304142F01 Page 5 of 10 Technical Specification Declaring the Frequency: 434MHz Modulation Type: ASK Antenna Type: PCB antenna Antenna Gain: 2 dBi (Declared by manufacturer) Number of Channels: 1 Report No.: NTC2304142F01 Page 6 of 10 2. Test Facility and Location Test Site : Dongguan Nore Testing Center Co., Ltd. (Dongguan NTC Co., Ltd.) Accreditations and Authorizations : The Laboratory has been assessed and proved to be in compliance with CNAS/CL01 Listed by CNAS, August 13, 2018 The Certificate Registration Number is L5795. The Certificate is valid until August 13, 2024 The Laboratory has been assessed and proved to be in compliance with ISO17025 Listed by A2LA, November 01, 2017 The Certificate Registration Number is 4429.01 Listed by FCC, November 06, 2017 Test Firm Registration Number: 907417 Listed by Industry Canada, June 08, 2017 The Certificate Registration Number. Is 46405-9743A Test Site Location : Building D, Gaosheng Science and Technology Park, Hongtu Road, Nancheng District, Dongguan City, Guangdong Province, China Report No.: NTC2304142F01 Page 7 of 10 3. Applicable Standards and References According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: Test Standards: 47 CFR Part 1, 1.1307 47 CFR Part 2, 2.1093 KDB 447498 D04 v01 Report No.: NTC2304142F01 Page 8 of 10 4. Maximum Permissible Exposure Limit According to 47 CFR Part 1, 1.1307, for single RF sources (i.e., any single fixed RF source, mobile device, or portable device, as defined in paragraph (b)(2) of this section): A single RF source is exempt if: 47 CFR Part 1, 1.1307 (A) The available maximum time- averaged power is no more than 1 mW, regardless of separation distance. This exemption may not be used in conjunction with other exemption criteria other than those in paragraph (b)(3)(ii)(A) of this section. Medical implant devices may only use this exemption and that in paragraph (b)(3)(ii)(A); (B) Or the available maximum time- averaged power or effective radiated power (ERP), whichever is greater, is less than or equal to the threshold P th (mW) described in the following formula. This method shall only be used at separation distances (cm) from 0.5 centimeters to 40 centimeters and at frequencies from 0.3 GHz to 6 GHz (inclusive). P th is given by: Where, And, d = the minimum separation distance (cm) in any direction from any part of the device antenna(s) or radiating structure(s) to the body of the device user. For multiple RF sources: Multiple RF sources are exempt if: Report No.: NTC2304142F01 Page 9 of 10…

Text truncated - open the document above for the full version.

Report No.: NTC2304142FV00 Dongguan Nore Testing Center Co., Ltd. Address: Building D, Gaosheng Science and Technology park, Hongtu road, Nancheng district, Dongguan city, Guangdong province, China Web: www.ntc-c.com Tel:+86-769-2202 2444 Fax:+86-769-2202 2799 Page 1 of 29 FCC RADIO TEST REPORT Applicant............................ : FOOFEE intelligent manufacturing Technology (dongguan) Co., Ltd. Address............................. : Room 401, Building 15, No.1 Pushi First Road, Qiaotou Town, Dongguan City, Guangdong Province, China Manufacturer....................... : FOOFEE intelligent manufacturing Technology (dongguan) Co., Ltd. Address.............................. : Room 401, Building 15, No.1 Pushi First Road, Qiaotou Town, Dongguan City, Guangdong Province, China Factory ............................ : FOOFEE intelligent manufacturing Technology (dongguan) Co., Ltd. Address ............................. : Room 401, Building 15, No.1 Pushi First Road, Qiaotou Town, Dongguan City, Guangdong Province, China Product Name..................... : Solar Bird Bath Fountain Pump Brand Name....................... : ERAARK Model No. .......................... : FFP02 FCC ID ............................... : 2A73O-FFP02 Measurement Standard.......... : 47 CFR FCC Part 15, Subpart C (Section 15.231) Receipt Date of Samples....... : April 11, 2023 Date of Tested..................... : April 11, 2023 to May 08, 2023 Date of Report..................... : May 10, 2023 This report shows that above equipment is technically compliant with the requirements of the standards above. All test results in this report apply only to the tested sample(s). Without prior written approval of Dongguan Nore Testing Center Co., Ltd, this report shall not be reproduced except in full. Prepared by Rose Hu / Project Engineer Approved by Iori Fan / Authorized Signatory Report No.: NTC2304142FV00 Page 2 of 29 Table of Contents 1. Summary of Test Result ............................................................................................................. 4 2. General Description of EUT ........................................................................................................ 5 3. Test Channels and Modes Detail ................................................................................................ 7 4. Configuration of EUT .................................................................................................................. 7 5. Modification of EUT .................................................................................................................... 7 6. Description of Support Device .................................................................................................... 7 7. Test Facility and Location ........................................................................................................... 8 8. Applicable Standards and References ....................................................................................... 9 9. Deviations and Abnormalities from Standard Conditions ............................................................ 9 10. Test Conditions ......................................................................................................................... 9 11. Measurement Uncertainty ...................................................................................................... 10 12. Sample Calculations ............................................................................................................... 11 13. Duty Cycle .............................................................................................................................. 12 14. Test Items and Results ........................................................................................................... 13 14.1 Conducted Emissions Measurement .................................................................................... 13 14.2 Radiated Spurious Emissions Measurement ........................................................................ 15 14.3 20dB Occupied Bandwidth ................................................................................................... 24 14.4 Transmission time ................................................................................................................ 26 14.5 Antenna Requirement ........................................................................................................... 28 15. Test Equipment List ................................................................................................................ 29 Report No.: NTC2304142FV00 Page 3 of 29 Revision History Report Number Description Issued Date NTC2304142FV00 Initial Issue 2022-05-10 Report No.: NTC2304142FV00 Page 4 of 29 1. Summary of Test Result FCC Rules Description of Test Result Remarks §15.207 (a) AC Power Line Conducted Emission N/A see note --- §15.231(b) & 15.209 Radiated Spurious Emission PASS --- §15.231(c) 20 dB Occupied bandwidth PASS --- §15.231(a) Transmission time PASS --- §15.203 Antenna Requirement PASS --- Note: AC Power Conducted Emission is not applicable due to the EUT only can be powered by battery. Report No.: NTC2304142FV00 Page 5 of 29 2. General Description of EUT Product Information Product Name: Solar Bird Bath Fountain Pump Main Model Name: FFP02 Additional Model Name: N/A Model Difference: N/A S/N: 2304-1847 Brand Name: ERAARK Hardware Version: FF-P02_V1.0 Software Version: HZ1226-12 Rating: DC 1.5V AAA battery* 2 Classification: Class B Typical arrangement: Table-top I/O Port: N/A Accessories Information Adapter: N/A Cable: N/A Other: N/A Additional Information Note: This product consists of two units, the fountain and the remote control, and this report only applies to remote control unit. Remark: All the information above are provided by the manufacturer. More detailed feature of the EUT please refers to the user manual. Report No.: NTC2304142FV00 Page …

Text truncated - open the document above for the full version.

产品承认书 SPECIFICATION FOR APPROVAL 产品名称/Model name： 天线/Antenna 产品型号/Model number： FFP02 版 次/Version： V1.0 日 期/Date： 2023-03-11 1、产品概述/ Product Information 1.1、外观图示/Appearance diagram： 图1 1.2、产品参数/Product specification： 产品测试参数表/Product specification 产品名称 Model name 433MHZ天线 产品型号 Model number FFP02 电性参数/ Electrical parameter 频率范围/ Frequency Range 433MHZ 输入阻抗/ Input Resistance 50Ω 极化方式/ Polarization 垂直 Vertical 辐射方向/ Radiation direction 全向 / Omnidirectional 驻波比/SWR ≤2.5 功率容量/ Power capacity 10W 增益/Gain 2dBi 带宽/ Bandwidth 433±5MHZ 尺寸/Size 155mm 铜泊厚度/ Cuprum thickness 1盎司 铜泊宽度/ Cuprum width 1.0mm 天线材料/ Antenna material 铜 工作温度/ Temperature range -20°C - ＋85°C 存放温度/ Storage temperature -40°C - ＋85°C 天线/ Antenna 2、天线尺寸/Antenna Size：

FCC ID: 2A73O-FFP02 Test Photo Radiated emission (Below 30MHz) Radiated emission (30-1000MHz) FCC ID: 2A73O-FFP02 Radiated emission (Above 1000MHz)