2A79Y-X1Laser engraving machine

Please read this instruction manual carefully before use Please use the laser engraving machine correctly and safely X1 User Manual .PRO Please read the user manual carefully before use and keep it in a safe place for further reference. For warranty and any technical support, please contact our service team: [email protected] Thank you for choosing WAINLUX laser engraving machine 01 Warning To assure continued compliance, any changes or modifications not expressly approved by the party.Responsible for compliance could void the user’s authority to operate this equipment. FCC Statement This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: The equipment complies with FCC Radiation exposure limits set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Caution use of controls or adjustment of performance of procedures other than those specified herein may result in hazardous radiation exposure 02 SAFETY INSTRUCTIONS Important Statement! All losses caused by improper use or failure to follow the steps in the manual shall be borne by the individual. The final right of interpretation of the manual belongs to our company, which also reserves the right to modify all information, data, technical details, etc. in this manual. Warning: When you purchase only the bare device, the device level is: Class IV laser device. Please wear laser protective glasses during use! ! ! When you purchase a device with a cover, the device level is: Class I laser device, which can prevent you from being harmed. Safety Precautions ★Before operating the equipment, users must carefully read the manual and strictly follow the operating procedures. ★Laser processing may be risky, and users should carefully consider whether the object being processed is suitable for laser operation. ★The processing object and emissions should comply with local laws and regulations. ★The laser radiation may cause the following situations: ① Ignition of surrounding flammable materials; ② During laser processing, other radiation and toxic and harmful gases may be generated due to different processing objects; ③ Direct exposure to laser radiation can cause human harm. Firefighting equipment must be equipped in the use site. It is prohibited to stack flammable and explosive items around the workbench and equipment. At the same time, it must be well ventilated. ★The environment where the equipment is located should be dry, free of pollution, vibration, strong electricity, strong magnetism and other interference and influence. The working environment temperature is 5~30°C, and the working environment humidity is 30-65% rh (no condensation) ★Equipment operating voltage: AC100-240V. ★The engraving machine and other related equipment must be safely grounded before they can be turned on and operated. ★When the equipment is turned on, it is necessary to be on duty throughout the process. All power supplies must be cut off before leaving to prevent abnormal conditions. If any abnormal conditions occur, please turn off the power immediately! ★It is strictly forbidden to place any irrelevant total reflection or diffuse reflection objects in the equipment to prevent the laser from reflecting on the human body or flammable items. ★The equipment should be kept away from electrical equipment that is sensitive to electromagnetic interference, which may cause electromagnetic interference to it. ★There is high voltage or other potential dangers inside the laser equipment, and non-professionals are strictly prohibited from disassembling it. Thank you for purchasing the WAINLUX laser engraving machine. In order to better use and maintain this equipment, please read this manual carefully and follow the steps in the manual. ！ 02 SAFETY INSTRUCTIONS 03 1. After the laser is turned on, it is strictly forbidden to aim at people, animals and flammable objects to avoid skin burns and fire. 2. The brightness of the laser is harmful to the eyes. Please do not look directly at the laser. 3. Keep your hands away from the machine when it is working to avoid injury 4. Turn off the power of the machine when it is not in use to avoid misopera- tion by a third party Notice!Maintenance and Care The laser module is a consumable. It is recommended to turn off the machine power for 10 minutes after 4 hours of engraving and 1 hour of cutting. SAFETY INSTRUCTIONS Mode: X1-10W-24V Optical Output Power: 10W Operating Temperature: 10-35°C Wavelength: 455 ± 5nm Light Path: Focused Beam DANGER LASER MODULES LASER APERTURE 01 Product Parameters..............................................…

Text truncated - open the document above for the full version.

[DongguanXinjia Laser TechnologyCo.,Ltd.] [Room602, No.419,JinxingRoad,LiaobuTown ] [Dongguan] [China ] Date : [202 4-0 7-15 ] FederalCommunicationsCommission Authorizationand EvaluationDivision 7435 OaklandMills Road Columbia,MD 21046 FCC ID: 2A79Y-X1 FRN of the Applicant:[0032743528] US Agent – AttestationStatement/ Part 2.911(d)(7) [DongguanXinjia Laser TechnologyCo.,Ltd.]certifies,that as of [2024-07-15], we have designated FCC US Agent,LLC to acceptserviceof processon our behalffor FCC ID: 2A79Y-X1. [DongguanXinjia Laser TechnologyCo.,Ltd.], acceptsto maintainan agent of serviceof process in the UnitedStatesfor no less than one year after either the granteehas permanentlyterminated all marketingand importationof the applicableequipmentwithin the U.S., or the conclusionof any Commission-relatedadministrativeor judicialproceedinginvolvingthe equipment,whicheveris later. FCC US Agent,LLC, acceptsas of the date of the filing of this application,the obligationof being the designatedagent for the purposeof acceptingserviceof processon behalfof [Dongguan Xinjia Laser TechnologyCo.,Ltd.] for FCC ID: 2A79Y-X1. DesignatedAgentInformation: CompanyName:FCC US Agent,LLC FRN: 0033402884 Address:3722 IllinoisAvenue,Saint Charles,IL, 60174,USA ContactPerson:Tim Payne Phone:708-571-3148 Email:[email protected] Sincerely, Company:[DongguanXinjia Laser Technology Co.,Ltd.] DesignatedAgent:FCC US Agent,LLC CompanyRepresentative:[Peng Wang]DesignatedAgent Representative:Tim Payne Signature:Signature:

Rev1/26/2023 (DongguanXinjiaLaserTechnologyCo.,Ltd.) EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 USA Date:2024.07.22 Ref:AttestationStatementsPart2.911(d)(5)(i)Filing FCCID：2A79Y-X1 [DongguanXinjiaLaserTechnologyCo.,Ltd.](“theapplicant”)certifiesthattheequipmentforwhich authorizationissoughtisnot“covered”equipmentprohibitedfromreceivinganequipment authorizationpursuanttosection2.903oftheFCCrules. Sincerely, (Applicantsignature) (PengWang) Rev1/26/2023 (DongguanXinjiaLaserTechnologyCo.,Ltd.) EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 USA Date:2024.07.22 Ref:AttestationStatementsPart2.911(d)(5)(ii)Filing FCCID：2A79Y-X1 [DongguanXinjiaLaserTechnologyCo.,Ltd.](“theapplicant”)certifiesthat,asofthedateofthefilingof theapplication,theapplicantisnotidentifiedontheCoveredList(asaspecificallynamedentityorany ofitssubsidiariesoraffiliates)asanentityproducing“covered” equipment. Sincerely, (Applicantsignature) (PengWang)

Declarationonmodeldifference Wetheundersignedherebyconfirmthatthesemodelsareidentical,andallmodelshavethesame RFmodule,PCBlayout,Antenna,schematicsandcomponent.Onlydifferentonmodelname. ProductionnameTrademarkFCCModelno. LaserengravingmachineWAINLUX2A79Y-X1JL3Pro,A6,A6Pro,A6Plus, A6Max,L2,L2Pro,L2Plus, L2Max,X1,X1Pro,X1Plus, X1Max,JL9,JL9Pro,JL9 Plus,JL9Max,JL3 Confirmedby: PengWang DongguanXinjiaLaserTechnologyCo.,Ltd. 2024-07-15

Pleaseproducealetteronyourcompanyletterheadwiththefollowinginformation.The lettermustbesubmittedinPDFform. 2024.07.15 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:CONFIDENTIALITYREQUESTFOR( ProductName：Laserengravingmachine ModelNumber ： JL3Pro,A6,A6Pro,A6Plus,A6Max,L2,L2 Pro,L2Plus,L2Max,X1,X1Pro,X1Plus,X1 Max,JL9,JL9Pro,JL9Plus,JL9Max,JL3 FCCID：2A79Y-X1 ) ToWhomItMayConcern: Thisletterservesasanofficialrequestforconfidentialityundersections0.457and0.459 ofCFR47.Wehaverequestedthatthe(BlockDiagram,Schematics,Operational Description)requiredtobesubmittedwiththisapplicationbepermanentlywithheld frompublicreview. SPECIFYREASONFORREQUEST(Theabovematerialscontaintradesecrets andproprietaryinformationnotcustomarilyreleasedtothepublic.Thepublic disclosureofthesematerialsmaybeharmfultotheapplicantandprovide unjustifiedbenefitstoitscompetitors.) Pleasecontactmeifthereisanyinformationyoumayneed. Sincerely, PengWang Mustbesignedbytheapplicantcontactcitedastechnicalornon-technicalcontactonthe 731formprovidedtoEurofinsMETLabs,orbytheauthorizedagentifanappropriate authorizedagentletterhasbeenprovided.Letterssignedbytheapplicantshouldbe placedonapplicantletterhead.

DongguanXinjiaLaserTechnologyCo.,Ltd. 2024.07.15 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:LETTEROFAGENTAUTHORIZATION ToWhomItMayConcern: We,theundersigned,herebyauthorizeSamLvatEMTEK(DONGGUAN)CO.,LTD.toacton ourbehalfinallmattersrelatingtoapplicationforequipmentauthorization,includingthesigning ofalldocumentsrelatingtothesematters. Wealsoherebycertifythatnopartytotheapplicationauthorizedhereunderissubjecttothe denialofbenefits,includingFCCbenefits,pursuanttoSection5301oftheAnti-DrugAbuseAct of1988,21U.S.C.853(a). Thisagreementexpiresoneyearfromthecurrentdate. Sincerely, PengWang Mustbesignedbytheapplicantcontactcitedastechnicalornon-technicalcontactonthe 731formprovidedtoEurofinsMETLabs,orbytheauthorizedagentifanappropriate authorizedagentletterhasbeenprovided.Letterssignedbytheapplicantshouldbe placedonapplicantletterhead.

FCCID:2A79Y-X1

FCCID:2A79Y-X1

ReportNo.EDG2406250151E00102RPage1of7Ver.1.0 TESTREPORT ProductName：Laserengravingmachine ModelNumber： JL3Pro,A6,A6Pro,A6Plus,A6Max,L2,L2 Pro,L2Plus,L2Max,X1,X1Pro,X1Plus,X1 Max,JL9,JL9Pro,JL9Plus,JL9Max,JL3 FCCID：2A79Y-X1 Preparedfor:DongguanXinjiaLaserTechnologyCo.,Ltd. Address:Room602,No.419,JinxingRoad,LiaobuTown,Dongguan City,GuangdongProvince Preparedby:EMTEK(DONGGUAN)CO.,LTD. Address:-1&2/F.,Building2,ZoneA,ZhongdaMarineBiotechnology ResearchandDevelopmentBase,No.9,XinchengAvenue, SongshanhuHigh-technologyIndustrialDevelopmentZone, Dongguan,Guangdong,China TEL:+86-0769-22807078 FAX:+86-0769-22807079 ReportNumber:EDG2406250151E00102R Date(s)ofTests:june25,2024tojuly08,2024 Dateofissue:july08,2024 $二维码$ ReportNo.EDG2406250151E00102RPage2of7Ver.1.0 TableofContents 1.TESTRESULTCERTIFICATION...............................................................................................................................................3 2.EUTSPECIFICATION.................................................................................................................................................................5 3.TESTREQUIREMENT:...............................................................................................................................................................6 RFEXPOSUREEVALUATION...................................................................................................................................................6 4.MEASUREMENTRESULT.........................................................................................................................................................7 ReportNo.EDG2406250151E00102RPage3of7Ver.1.0 1.TESTRESULTCERTIFICATION Applicant:DongguanXinjiaLaserTechnologyCo.,Ltd. Address: Room602,No.419,JinxingRoad,LiaobuTown,DongguanCity,Guangdong Province Manufacturer:DongguanXinjiaLaserTechnologyCo.,Ltd. Address: Room602,No.419,JinxingRoad,LiaobuTown,DongguanCity,Guangdong Province Factory:DongguanXinjiaLaserTechnologyCo.,Ltd. Address: Room602,No.419,JinxingRoad,LiaobuTown,DongguanCity,Guangdong Province EUT:Laserengravingmachine ModelName: JL3Pro,A6,A6Pro,A6Plus,A6Max,L2,L2Pro,L2Plus,L2Max,X1,X1Pro, X1Plus,X1Max,JL9,JL9Pro,JL9Plus,JL9Max,JL3 Trademark:WAINLUX MeasurementProcedureUsed: APPLICABLESTANDARDS STANDARDTESTRESULT §15.247(i),§2.1093 PASS TheaboveequipmentwastestedbyEMTEK(DONGGUAN)CO.,LTD.Thetestdata,dataevaluation,test procedures,andequipmentconfigurationsshowninthisreportweremadeinaccordancewiththeprocedures giveninANSIC63.10(2013)andtheenergyemittedbythesampleEUTtestedasdescribedinthisreportisin compliancewiththerequirementsofFCCRulesFCC§15.247(i),§2.1093. Thetestresultsofthisreportrelateonlytothetestedsampleidentifiedinthisreport DateofTest:june25,2024tojuly08,2024 Preparedby: WarrenDeng/Editor Reviewer: TimDong/ Supervisor Approve&AuthorizedSigner: SamLv/Manager ReportNo.EDG2406250151E00102RPage4of7Ver.1.0 ModifiedHistory VersionReportNo.RevisionDateSummary EDG2406250151E00102R/OriginalReport ReportNo.EDG2406250151E00102RPage5of7Ver.1.0 2. EUTSpecification CharacteristicsDescription Product:Laserengravingmachine ModelNumber: JL3Pro,A6,A6Pro,A6Plus,A6Max,L2,L2Pro,L2Plus,L2Max,X1,X1 Pro,X1Plus,X1Max,JL9,JL9Pro,JL9Plus,JL9Max,JL3 Note:Allmodelsarethesame,exceptthemodelname.SelectmodelJL3Pro heretocompleteallthetests. Sample:2# DeviceType: 2.4GWIFI DataRate: 802.11b 802.11g 802.11n(20MHzchannelbandwidth) 802.11n(40MHzchannelbandwidth) Modulation: DSSSwithDBPSK/DQPSK/CCKfor802.11b; OFDMwithBPSK/QPSK/16QAM/64QAMfor802.11g/n; OperatingFrequency Range(s): 2412-2462MHzfor802.11b/g/n(HT20); 2422-2452MHzfor802.11n(HT40); NumberofChannels: 11channelsfor802.11b/g/n(HT20); 7Channelsfor802.11n(HT40); TransmitPowerMax: 14.53dBm(0.028379W) AntennaGain:3.05dBi Powersupply: AC100-240V,50/60Hz Evaluationapplied:MPEEvaluation SAREvaluation ReportNo.EDG2406250151E00102RPage6of7Ver.1.0 3. TestRequirement: RFEXPOSUREEVALUATION Accordingto§15.247(i)and§1.1307(b)(1),systemsoperatingundertheprovisionsofthissectionshallbe operatedinamannerthatensuresthatthepublicisnotexposedtoradiofrequencyenergylevelinexcessof theCommission’sguidelines. RoutineSARevaluationreferstothatspecificallyrequiredby§2.1093,usingmeasurementsorcomputer simulation.WhenroutineSARevaluationisnotrequired,portabletransmitterswithoutputpowergreaterthan theapplicablelowthresholdrequireSARevaluationtoqualityforTCBapproval. OneantennaisavailablefortheEUT.Theminimumseparationdistanceis5mm. ReportNo.EDG2406250151E00102RPage7of7Ver.1.0 4. MeasurementResult Antennagain: 2.4G:3.05dBi 802.11b:AntennaA Channe l Channe lFreq. (MHz) Outpu t Power (dBm) E.I.R.P(d Bm) TargetPower W/tolerance (dBm) Maxtune up power(dBm )tolerance Max tuneup power(mW )tolerance Power Densityat R=20cm (mW/cm2 ) Power density Limits (mW/cm2 ) 1241214.5317.5817±11863.100.0253351 6243713.7516.8016±11750.120.0201251 11246214.2617.3117±11863.100.0253351 802.11g:AntennaA Channe l Channe lFreq. (MHz) Outpu t Power (dBm) E.I.R.P(d Bm) TargetPower W/tolerance (dBm) Maxtune up power(dBm )tolerance Max tuneup power(mW )tolerance Power Densityat R=20cm (mW/cm2 ) Power density Limits (mW/cm2 ) 1241211.714.7514±11531.620.0126981 6 243712.34 15.3915±11639.810.015986 1 11246210.9714.0214±11531.620.0126981 802.11nHT20:AntennaA Channe l Channe lFreq. (MHz) Outpu t Power (dBm) E.I.R.P(d Bm) TargetPower W/tolerance (dBm) Maxtune up power(dBm )tolerance Max tuneup power(mW )tolerance Power Densityat R=20cm (mW/cm2 ) Power density Limits (mW/cm2 ) 1241211.5414.5914±11531.620.0126981 6243710.5613.6113±11425.120.0100861 11246210.7513.8013±11425.120.0100861 802.11nHT40:AntennaA Channe l Channe lFreq. (MHz) Outpu t Power (dBm) E.I.R.P(d Bm) TargetPower W/tolerance (dBm) Maxtune up power(dBm )tolerance Max tuneup power(mW )tolerance Power Densityat R=20cm (mW/cm2 ) Power density Limits (mW/cm2 ) 3242210.5813.6313±11425.120.0100861 6243710.1213.1713±11425.120.0100861 9245210.2113.2613±11425.120.0100861 AccordingtoKDB447498,nostand…

Text truncated - open the document above for the full version.

Antenna specification Customer name： Customer item： Ke Xin Liao Hao： Specification: 2.4G new soft built-in -RG1.13 line /12CM/IPEX Date of production: July 10, 2024 DepartmentReview approve 刘RF department啸 李斌 李志 Structural department 晓李斌 王 Quality department 飞 李斌 TEL:0755-2822057 B u i l d i n g H , Ho n g y o n g l i In d u s t r i a l Z o n e, S h a b e i l i e, B a o l o n g S t r e e t, Lo n g g a n g Di s t r i c t, S h e n z h e n C Co m p a n y a d d r e s s： i t y 2 FAX：0755-28483275 第1页共4页 Manufacturer: Shenzhen Kexin Wireless Technology Co., Ltd. 1.Product picture ： 2．Electrical performance test report,VSWR： 第2页共4页 频率范围 FrequencyRange(MHz 电性能指标ElectricalSpecification 3 ． Product performance parameters s ) 2400-2500 输入阻抗 InputImpendence(Ω) 50 电压驻波比V.S.W.R≤2.0（未匹配设备，仅供参考） 增益 Gain(dBi) 3 ± 0.5 （未匹配设备，仅供参考） 极化形式 PolarizationType 垂直 Vertical 最大功率Maximumpower(W) 10W 垂直面波瓣角度 VerticallobeAngle （ E ） 45~60° 水平面波瓣角度 WaterplanelobeAngle （ H ） 360° 机械指标MechanicalSpecifications 天线材质 Material FPC 连接器型号ConnectType IPEX1代 天线尺寸 Size 45*10*0.25mm 工作温度OperatingTemp -20~+65 ̊C 第3页共4页 4． 2D： 第4页共4页

ReportNo.EDG2406250151E00101RPage1of86Ver.1.0 TESTREPORT ProductName：Laserengravingmachine ModelNumber ： JL3Pro,A6,A6Pro,A6Plus,A6Max,L2,L2 Pro,L2Plus,L2Max,X1,X1Pro,X1Plus,X1 Max,JL9,JL9Pro,JL9Plus,JL9Max,JL3 FCCID：2A79Y-X1 Preparedfor:DongguanXinjiaLaserTechnologyCo.,Ltd. Address:Room602,No.419,JinxingRoad,LiaobuTown,Dongguan City,GuangdongProvince Preparedby:EMTEK(DONGGUAN)CO.,LTD. Address:-1&2/F.,Building2,ZoneA,ZhongdaMarineBiotechnology ResearchandDevelopmentBase,No.9,XinchengAvenue, SongshanhuHigh-technologyIndustrialDevelopmentZone, Dongguan,Guangdong,China TEL:+86-0769-22807078 FAX:+86-0769-22807079 ReportNumber:EDG2406250151E00101R Date(s)ofTests:june25,2024tojuly08,2024 Dateofissue:july08,2024 $二维码$ ReportNo.EDG2406250151E00101RPage2of86Ver.1.0 TABLEOFCONTENTS 1TESTRESULTCERTIFICATION........................................................................................................................3 2EUTTECHNICALDESCRIPTION......................................................................................................................5 3SUMMARYOFTESTRESULT.............................................................................................................................6 4TESTMETHODOLOGY........................................................................................................................................7 4.1GENERALDESCRIPTIONOFAPPLIEDSTANDARDS...............................................................................7 4.2MEASUREMENTEQUIPMENTUSED...........................................................................................................7 4.3DESCRIPTIONOFTESTMODES...................................................................................................................8 5FACILITIESANDACCREDITATIONS...............................................................................................................9 5.1FACILITIES........................................................................................................................................................9 5.2LABORATORYACCREDITATIONSANDLISTINGS...................................................................................9 6TESTSYSTEMUNCERTAINTY........................................................................................................................10 7SETUPOFEQUIPMENTUNDERTEST...........................................................................................................11 7.1RADIOFREQUENCYTESTSETUP1...........................................................................................................11 7.2RADIOFREQUENCYTESTSETUP2...........................................................................................................11 7.3CONDUCTEDEMISSIONTESTSETUP......................................................................................................14 7.4BLOCKDIAGRAMCONFIGURATIONOFTESTSYSTEM......................................................................15 7.5SUPPORTEQUIPMENT.................................................................................................................................15 8TESTREQUIREMENTS......................................................................................................................................16 8.1DTS6DBBANDWIDTH.................................................................................................................................16 8.2DTS99%BANDWIDTH.................................................................................................................................24 8.3MAXIMUMPEAKCONDUCTEDOUTPUTPOWER.................................................................................32 8.4MAXIMUMPOWERSPECTRALDENSITY................................................................................................40 8.5UNWANTEDEMISSIONSINNON-RESTRICTEDFREQUENCYBANDS..............................................48 8.6RADIATEDSPURIOUSEMISSION..............................................................................................................73 8.7CONDUCTEDEMISSIONTEST....................................................................................................................81 8.8ANTENNAAPPLICATION.............................................................................................................................84 ReportNo.EDG2406250151E00101RPage3of86Ver.1.0 1TESTRESULTCERTIFICATION Applicant:DongguanXinjiaLaserTechnologyCo.,Ltd. Address: Room602,No.419,JinxingRoad,LiaobuTown,DongguanCity,Guangdong Province Manufacturer:DongguanXinjiaLaserTechnologyCo.,Ltd. Address: Room602,No.419,JinxingRoad,LiaobuTown,DongguanCity,Guangdong Province Factory:DongguanXinjiaLaserTechnologyCo.,Ltd. Address: Room602,No.419,JinxingRoad,LiaobuTown,DongguanCity,Guangdong Province EUT:Laserengravingmachine ModelName: JL3Pro,A6,A6Pro,A6Plus,A6Max,L2,L2Pro,L2Plus,L2Max,X1,X1Pro, X1Plus,X1Max,JL9,JL9Pro,JL9Plus,JL9Max,JL3 Trademark:WAINLUX MeasurementProcedureUsed: APPLICABLESTANDARDS STANDARDTESTRESULT FCC47CFRPart2,SubpartJ FCC47CFRPart15,SubpartC PASS ICRSS-GEN,Issue5(04-2018)+A1(03-2019)+A2(02-2021) ICRSS-247Issue2(02-2017) PASS TheaboveequipmentwastestedbyEMTEK(DONGGUAN)CO.,LTD.Thetestdata,dataevaluation, testprocedures,andequipmentconfigurationsshowninthisreportweremadeinaccordancewiththe proceduresgiveninANSIC63.10(2013)andtheenergyemittedbythesampleEUTtestedasdescribed inthisreportisincompliancewiththerequirementsofFCCRulesPart2andPart15.247 Thetestresultsofthisreportrelateonlytothetestedsampleidentifiedinthisreport. DateofTest:june25,2024tojuly08,2024 Preparedby: WarrenDeng/ Editor Reviewer: TimDong/Supervisor Approve&AuthorizedSigner: SamLv/Manager ReportNo.EDG2406250151E00101RPage4of86Ver.1.0 ModifiedHistory VersionReportNo.RevisionDateSummary V1.0EDG2406250151E00101R/OriginalReport ReportNo.EDG2406250151E00101RPage5of86Ver.1.0 2EUTTECHNICALDESCRIPTION Note:formoredetails,pleaserefertotheUser’smanualoftheEUT. C…

Text truncated - open the document above for the full version.

ReportNo.EDG2406250151E00101RPage39of86Ver.1.0 11N40SISO-Ant1-2437-PASS 11N40SISO-Ant1-2452-PASS ReportNo.EDG2406250151E00101RPage40of86Ver.1.0 8.4MAXIMUMPOWERSPECTRALDENSITY 8.4.1ApplicableStandard AccordingtoFCCPart15.247(e)andKDB558074D0115.247MeasGuidancev05r02 AccordingtoRSS-2475.2(b)andRSS-Gen6.12 8.4.2ConformanceLimit Thetransmitterpowerspectraldensityconductedfromthetransmittertotheantennashallnotbegreater than8dBminany3kHzbandduringanytimeintervalofcontinuoustransmission.Thispowerspectral densityshallbedeterminedinaccordancewiththeprovisionsofsection5.4(d),(i.e.thepowerspectral densityshallbedeterminedusingthesamemethodasisusedtodeterminetheconductedoutputpower). 8.4.3TestConfiguration Testaccordingtoclause6.1radiofrequencytestsetup 8.4.4TestProcedure Thisprocedureshallbeusedifmaximumpeakconductedoutputpowerwasusedtodemonstrate compliance Thetransmitteroutput(antennaport)wasconnectedtothespectrumanalyzer SetanalyzercenterfrequencytoDTSchannelcenterfrequency. Setthespanto1.5timestheDTSbandwidth. SettheRBWto:3kHz SettheVBWto:10kHz. SetDetector=peak. SetSweeptime=autocouple. SetTracemode=maxhold. Allowtracetofullystabilize. UsethepeakmarkerfunctiontodeterminethemaximumamplitudelevelwithintheRBW. 8.4.5TestResults Temperature: 25 ̊C RelativeHumidity: 45  ATMPressure:1011mbar Note:N/A ReportNo.EDG2406250151E00101RPage41of86Ver.1.0 TestModeAntennaFrequency[MHz]Result[dBm/3-100kHz]Limit[dBm/3kHz]Verdict 11BAnt12412-14.02≤8.00PASS 11BAnt12437-14.60≤8.00PASS 11BAnt12462-13.19≤8.00PASS 11GAnt12412-17.84≤8.00PASS 11GAnt12437-18.46≤8.00PASS 11GAnt12462-16.68≤8.00PASS 11N20SISOAnt12412-18.13≤8.00PASS 11N20SISOAnt12437-16.83≤8.00PASS 11N20SISOAnt12462-16.73≤8.00PASS 11N40SISOAnt12422-19.10≤8.00PASS 11N40SISOAnt12437-17.89≤8.00PASS 11N40SISOAnt12452-17.71≤8.00PASS ReportNo.EDG2406250151E00101RPage42of86Ver.1.0 11B-Ant1-2412-PASS 11B-Ant1-2437-PASS ReportNo.EDG2406250151E00101RPage43of86Ver.1.0 11B-Ant1-2462-PASS 11G-Ant1-2412-PASS ReportNo.EDG2406250151E00101RPage44of86Ver.1.0 11G-Ant1-2437-PASS 11G-Ant1-2462-PASS ReportNo.EDG2406250151E00101RPage45of86Ver.1.0 11N20SISO-Ant1-2412-PASS 11N20SISO-Ant1-2437-PASS ReportNo.EDG2406250151E00101RPage46of86Ver.1.0 11N20SISO-Ant1-2462-PASS 11N40SISO-Ant1-2422-PASS ReportNo.EDG2406250151E00101RPage47of86Ver.1.0 11N40SISO-Ant1-2437-PASS 11N40SISO-Ant1-2452-PASS ReportNo.EDG2406250151E00101RPage48of86Ver.1.0 8.5UNWANTEDEMISSIONSINNON-RESTRICTEDFREQUENCYBANDS 8.5.1ApplicableStandard AccordingtoFCCPart15.247(d)andKDB558074D0115.247MeasGuidancev05r02 AccordingtoRSS-2475.5 8.5.2ConformanceLimit AccordingtoFCCPart15.247(d): Inany100kHzbandwidthoutsidethefrequencybandinwhichthespreadspectrumordigitally modulateddeviceisoperating,theRFpowerthatisproducedshallbeatleast20dBbelowthatinthe100 kHzbandwidthwithinthebandthatcontainsthehighestlevelofthedesiredpower,basedoneitheranRF conductedoraradiatedmeasurement,providedthatthetransmitterdemonstratescompliancewiththe peakconductedpowerlimits.Ifthetransmittercomplieswiththeconductedpowerlimitsbasedontheuse ofroot-mean-squareaveragingoveratimeinterval,aspermittedundersection5.4(d),theattenuation requiredshallbe30dBinsteadof20dB.Attenuationbelowthegeneralfieldstrengthlimitsspecified inRSS-Genisnotrequired. 8.5.3TestConfiguration Testaccordingtoclause6.1radiofrequencytestsetup 8.5.4TestProcedure Thetransmitteroutput(antennaport)wasconnectedtothespectrumanalyzer Referencelevelmeasurement Establishareferencelevelbyusingthefollowingprocedure: SetinstrumentcenterfrequencytoDTSchannelcenterfrequency. Setthespanto≥1.5timestheDTSbandwidth. SettheRBW=100kHz. SettheVBW≥3xRBW. SetDetector=peak. SetSweeptime=autocouple. SetTracemode=maxhold. Allowtracetofullystabilize. UsethepeakmarkerfunctiontodeterminethemaximumPSDlevel. NotethatthechannelfoundtocontainthemaximumPSDlevelcanbeusedtoestablishthereference level. Band-edgemeasurement Usethefollowingspectrumanalyzersettings: Span=wideenoughtocapturethepeakleveloftheemissionoperatingonthechannelclosesttothe band-edge,aswellasanymodulationproductswhichfalloutsideoftheauthorizedbandofoperation SetRBW  1%ofthespan=100kHzSetVBW  3xRBW SetSweep=autoSetDetectorfunction=peakSetTrace=maxhold Allowthetracetostabilize.Setthemarkerontheemissionatthebandedge,oronthehighest modulationproductoutsideoftheband,ifthislevelisgreaterthanthatatthebandedge.Enablethe marker-deltafunction,thenusethemarker-to-peakfunctiontomovethemarkertothepeakofthein-band emission.Themarker-deltavaluenowdisplayedmustcomplywiththelimitspecifiedinthisSection. Emissionlevelmeasurement Setthecenterfrequencyandspantoencompassfrequencyrangetobemeasured. SettheRBW=100kHz. SettheVBW=300kHz. SetDetector=peak Sweeptime=autocouple. Tracemode=maxhold. Allowtracetofullystabilize. Usethepeakmarkerfunctiontodeterminethemaximumamplitudelevel. Ensurethattheamplitudeofallunwantedemissionsoutsideoftheauthorizedfrequencyband(excluding restrictedfrequencybands)areattenuatedbyatleasttheminimumrequirements.Reportthethree highestemissionsrelativetothelimit. ReportNo.EDG2406250151E00101RPage49of86Ver.1.0 8.5.5TestResults Temperature: 25 ̊ C RelativeHumidity: 45  ATMPressure:1011mbar Note:N/A TestModeAntennaFrequency[MHz] FreqRange [Mhz] RefLevel [dBm] Result [dBm] Limit [dBm] Verdict 11BAnt124120~Reference4.624.62---PASS 11BAnt1241230~10004.62-53.4≤-25.38PASS 11BAnt124121000~265004.62-50.15≤-25.38PASS 11BAnt124370~Reference3.113.11---PASS 11BAnt1243730~10003.11-53.69≤-26.89PASS 11BAnt124371000~265003.11-49.95≤-26.89PASS 11BAnt124620~Reference3.503.50---PASS 11BAnt1246230~10003.50-56.29≤-26.5PASS 11BAnt124621000~265003.50-51.04≤-26.5PASS 11GAnt124120~Reference-1.71-1.71---PASS 11GAnt1241230~1000-1.71-54.44≤-31.71PASS 11GAnt124121000~26500-1.71-50.16≤-31.71PASS 11GAnt124370~Reference-1.59-1.59---PASS 11GAnt1243730~1000-1.59-55.56≤-31.59PASS 11GAnt124371000~26500-1.59…

Text truncated - open the document above for the full version.