2A8ZSH0010IGBRemote Camera Assistant mini

InstallationandusemanualofRemoteCameraAssistant mini Canonversion Without written authorization from Zhongshan Yueguang Intelligent Imaging Technology Co ., Ltd., any form of complete or partial replication of this manual is strictly prohibited (exceptforsimplequotationsforarticleorcommentevaluationpurposes). June2023 ZhongshanYueguangIntelligentImagingTechnologyCo.,Ltd. Address:ZoneC,R306,#7,ZhangqiTechnologyBusinessIncubator,No.70,ZhongshanCity, China Phone:0086-0760-89878172 Website:www.ueleret.cn Preface ThankyouforyourtrustinchoosingUeleretRemoteCameraAssistantmini. Wewillservewholeheartedlyforyou. TheRemoteCameraAssistantminicanberemotelycontrolthedigitalcameraandsmart stabilizer.Therearetwodifferentcommunicationdistanceoptionsavailable.Betweenthe stabilizerandoperator,itallowstocontrolwithinarangeof0m-500mwithoutblockingor slightlyblockingthetransmissionsignal. Thismanualisapplicabletobothmodelsofcommunicationdistancesof500m. Theremotecameraassistantminicanbeupgradedtotheinfraredtriggerversionwhich addsautocapturefunctionandbringsmoreconvenienceforyourphotography. Toensureasmoothuserexperience,readingthemanual,wekindlyasktheownerto carefullyreadandfamiliarizethemselveswiththeoperatingandinspectionprocedures outlinedinthismanual. Pleasereadthisusermanualthoroughlyandstartanenjoyablejourneyofexperience. 3 Content Installationand use manual of Remote Camera Assistantmini .................................................1 Canon version ...............................................................................................................................................1 Preface ......................................................................................................................................................................2 Chapter 1. Product Structureand parts introductionof Remote Camera Assistantmini ........... 5 Structurediagram of smart stabilizer ...................................................................................................5 Name of each parts of Remote Camera Assistantmini .................................................................7 Each interface functionsof smart stabilizer ........................................................................................8 Lens zoom controlleraccessories..........................................................................................................9 Parts functionsintroductionof Remote Camera Assistantmini ...............................................10 Chapter 2: Installationof Smart PhotographyHandheldMini Product ..........................................13 Prepare in advance,inspect items and pack neatly (StronglyRecommended,develop aHabit) ...................................................................................................................................................................................13 Site Survey and Selectionfor Shooting(StronglyRecommended,Develop aHabit) ............... 14 Installationsteps of smart stabilizer .............................................................................................................15 Case 1: Smart stabilizerinstalled on ahard floor ....................................................................................15 1. Mount the shootingdirectionbase on the tripod. ...................................................................15 2.Mount the smart stabilizeron the shootingdirectionbase. ..................................................15 3.Install the lens zoom controller........................................................................................................15 4. Attach the zoom ring to the camera lens. ...................................................................................16 5. Mount the camera onto the smart stabilizer ..............................................................................16 6. Install the camera battery converter..............................................................................................16 7.Match and connect the cables according to the markings on the main control board.17 8. Screw the two omnidirectionalantennasclockwiseonto the correspondinginterfaces at the top of the stabilizerantenna arm. ..........................................................................................18 9. Move the lens zoom controller.....................................................................................................18 10. Ensure atight fit between the lens zoom controllerand the camera lens zoom gear. 18 Case2: Installingthe smart stabilizeron water or muddy ground ..................................................19 1. Install the shootingdirectionbase. ................................................................................................19 2. Place the smart stabilizeron the car seat or ahard surface. ................................................19 Chapter 3. On-site debuggingof the smart stabilizer ..........................................................................20 Chapter 4. On-site preparationfor remote shooting ...........................................................................21 Chapter 5. On-site debuggingof the remote camera assistant for remote shooting .............. 21 Chapter 6. Power-savingoperationand hibernationmode settings for the remote camera assistant mini ........................................................................................................................................................22 Chapter 7. Product specificationsand technicalparameters.............................................................24 Chapter 8. Safety precautionsfor the remote camera assistant mini .............................................24 Chapter 9. Power supply specificationsand maintenance..................................................................27 1.Batteryspecificationsand parameterslist ...................................................................…

Text truncated - open the document above for the full version.

Zhongshan Yueguang Intelligent Imaging Technology Co., Ltd. Address: Zone C, R 306, #7, Zhangqi Technology Business Incubator, No. 70, Zhongshan City, China Tel.: 18023068606 E‐mail: [email protected] Date: 2023-08-28 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attestation letter Dear Sir or Madam, We, Zhongshan Yueguang Intelligent Imaging Technology Co., Ltd., declare that our product name: Remote Camera Assistant mini, model name: H0010, FCC ID: 2A8ZSH0010IGB) wh ich chip (Model: AR9344) supports 5G WiFi band 1/band 4 (802.11a, 802.11n20), for marketing purpose, other functions have been shielded by manufacturer though software and the end user can not have the capability to activate these functions. Sincerely, Signature: Name: Wenhong Wan Title: Assistant

ZhongshanYueguangIntelligentImagingTechnologyCo.,Ltd. CFR47§2.911(d)(5)(i)AttestationLetter AttestationLetter Date:08/28/2023 FEDERALCOMMUNICATIONSCOMMISSIONS AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 Ref:AttestationStatementsCFR47§2.911(d)(5)(i)Filing FCCID:2A8ZSH0010IGB ZhongshanYueguangIntelligentImagingTechnologyCo.,Ltd.(“theapplicant”)certifiesthat theequipmentforwhichauthorizationissoughtisnot “covered”equipmentprohibitedfrom receivinganequipmentauthorizationpursuanttosection2.903oftheFCCrules. Sincerely, Signature Name:WenhongWan Title:Assistant Address:ZoneC,R306,#7,ZhangqiTechnologyBusinessIncubator,No.70,ZhongshanCity, China Tel.:18023068606 E-mail:[email protected]

ZhongshanYueguangIntelligentImagingTechnologyCo.,Ltd. CFR47§2.911(d)(5)(ii)AttestationLetter AttestationLetter Date:08/28/2023 FEDERALCOMMUNICATIONSCOMMISSIONS AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 Ref:AttestationStatementsCFR47§2.911(d)(5)(ii)Filing FCCID:2A8ZSH0010IGB ZhongshanYueguangIntelligentImagingTechnologyCo.,Ltd.(“theapplicant”)certifiesthatas ofthedateofthefilingoftheapplication,theapplicantisnot identifiedontheCoveredListas anentityproducing“covered”equipment. Sincerely, Signature Name:WenhongWan Title:Assistant Address:ZoneC,R306,#7,ZhangqiTechnologyBusinessIncubator,No.70,ZhongshanCity, China Tel.:18023068606 E-mail:[email protected]

ZhongshanYueguangIntelligentImagingTechnologyCo.,Ltd. Address:ZoneC,R306,#7,ZhangqiTechnologyBusinessIncubator,No.70,Zhongshan City,China Tel.:18023068606 E-mail:[email protected] QA-FR-170-B FCCAuthorization Date:2023-08-28 FEDERALCOMMUNICATIONSCOMMISSIONS AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 Subject:AgentAuthorization Towhomitmayconcern: We, Zhongshan Yueguang Intelligent Imaging Technology Co., Ltd. hereby authorize China Certification ICT Co., Ltd (Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd (Dongguan) on our behalf shall have the same effect as our own action. We,ZhongshanYueguangIntelligentImagingTechnologyCo.,Ltd.theundersigned, herebycertifythatwearenotsubjecttoadenialoffederalbenefits,thatincludesFCC benefits,pursuanttoSection5301oftheAnti-DrugAbuseActof1988,21U.S.C.862. Thisauthorizationisvaliduntilfurtherwrittennoticefromtheapplicant. SincerelyYours, Signature Name:WenhongWan Title:Assistant

Zhongshan Yueguang Intelligent Imaging Technology Co., Ltd. Address: Zone C, R 306, #7, Zhangqi Technology Business Incubator, No. 70, Zhongshan City, China Tel.: 18023068606 E-mail: [email protected] FCC Confidential Authorization Date: 2023-08-28 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2A8ZSH0010IGB In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Zhongshan Yueguang Intelligent Imaging Technology Co., Ltd. hereby requests long-term confidential treatment of information accompanying this application as outlined below: Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature Name: Wenhong Wan Title: Assistant  SOFTWARE SECURITY DESCRIPTION

China Certification ICT Co., Ltd (Dongguan) Report No.: CR230550738-EXP Page 1 of 11 EUT EXTERNAL PHOTOGRAPHS Page 2 of 11 Page 3 of 11 Page 4 of 11 Page 5 of 11 Page 6 of 11 Page 7 of 11 Page 8 of 11 Page 9 of 11 ANT ANT Page 10 of 11 Page 11 of 11 ANT1 PORT(Chain 0) ANT2 PORT(Chain 1)

FCC ID Label

China Certification ICT Co., Ltd (Dongguan) Report No.: CR230550738-INP Page 1 of 8 EUT INTERNAL PHOTOGRAPHS uncover Page 2 of 8 Page 3 of 8 Page 4 of 8 Page 5 of 8 chip chip Page 6 of 8 chip chip Page 7 of 8 chip Page 8 of 8 chip

China Certification ICT Co., Ltd (Dongguan) Report No.: CR230550738-00 Page 62 of 64 5. RF EXPOSURE EVALUATION 5.1 Applicable Standard FCC §15.407 and subpart §1.1307 Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. 5. 2 Procedure According to §1.1307(b)(3)(i) (C) Or using Table 1 and the minimum separation distance (R in meters) from the body of a nearby person for the frequency (f in MHz) at which the source operates, the ERP (watts) is no more than the calculated value prescribed for that frequency. For the exemption in Table 1 to apply, R must be at least λ/2π, where λ is the free-space operating wavelength in meters. If the ERP of a single RF source is not easily obtained, then the available maximum time-averaged power may be used in lieu of ERP if the physical dimensions of the radiating structure(s) do not exceed the electrical length of λ/4 or if the antenna gain is less than that of a half-wave dipole (1.64 linear value). Table 1 to § 1.1307(b)(3)(i)(C) - Single RF Sources Subject to Routine Environmental Evaluation RF Source frequency (MHz) Threshold ERP (watts) 0.3-1.34 1,920 R 2 . 1.34-30 3,450 R 2 /f 2 . 30-300 3.83 R 2 . 300-1,500 0.0128 R 2 f. 1,500-100,000 19.2R 2 . 5.3 Measurement Result Radio Frequency (MHz) λ/2Π (mm) Distance (mm) Exemption ERP (mW) Maximum Conducted Power including Tune-up Tolerance (dBm) Antenna Gain (dBi) ERP dBmmW 5.2G WLAN 5180-5240 9.22 200 768 21 1.38 20.23 105.44 5.8G WLAN 5745-5825 8.31 200 768 20 1.63 19.48 88.72 Note: The Maximum Conducted Power including Tune-up Tolerance was declared by manufacturer. Result: The device compliant the MPE-Based Exemption at 20cm distances.

承认书 SPECIFICATION FORAPPROVAL 5150-5850MHz rubber duck Antenna KXWX-5150-5850MHz J-Z Customer: Customer’s part number: Product description: Product part number: Issue Date: Note: 2019/11/07 5150-5850MHz Customer Use Customer's authorized signature Remarks Full approved Conditional approved Rejected Shenzhen Kexin Wireless Technology Co., Ltd 3F, Building H, Hongyong Li Industrial Zone, Shabeili, Longxin Community, Longgang Street, Shenzhen 一、产品参数 型号KXWX-433E-4 主要技术指标 频率范围（MHz） 5150-5850±5MHZ 电压驻波比≤1.5 增益（dBi） 最大功率（W 1.63 ）50 输入阻抗（Ω）50 极化形式垂直极化 天线尺寸（mm）200+/-5 Model Main Technical Specifications Frequency Range（MHz） 5150-5850±5MHZ VSWR≤1.5 Gain（dBi） Max Input power（W 1.63 ）50 Input Impedance（Ω）50 Polarization TypeVertical Antenna Size（mm）200+/-5 (Product parameterts) 二、产品规格 (Specifications) 1. 电气测试 (ElectricalCharacteristic) ITEM项目TESTCONDITION测试环境SPECIFICATION 规格 1 电压驻波比 VSWR UsingPROTEKA333networkinganalyzer tomeasureAntennaS1VSWR characteristics 使用 PROTEKA333 网路分析仪测试天线 S1 之电压驻波比参数 PIC1 2阻抗 SmithChart UsingPROTEKA333networkinganalyzer tomeasureAntennaS1SmithChart characteristics 使用PROTEKA333网路分析仪测试天线 S1之史密斯阻抗参数 PIC2 3增益响应 GainResponse UsingPROTEKA333networkinganalyzer tomeasureAntennaS1GainResponse characteristics 使用PROTEKA333网路分析仪测试天线 S1之史密斯阻抗参数 2. 机械性能（ MECHANICALCHARACTERISTICS ） 1摇摆测试 BENDINGTEST Putload120gattheendofthewire, fixedjoints,swayingtestatanangleof 60degrees,testfeaturesafter1000 times 放离接头30CM的线端上荷重120g，固 定接头后进行摇摆测试，左右角度各60 度，1000次后测试特性. Nosignofdamage 2 强度测试 STRENGTEST 15poundsofstaticloadappliedtothe bottomoftheactinomycetesendforone minute. 一个 15 磅之静负荷施加放线端底部持续 一分钟. Nosignofdamage 3拉力测试 PULLINGFORCE Pulltestwithatensionmeterbetween connectorandwire 用拉力计接头及线材间进行拉力测试. Nosignofdamage 4振动测试 VIBRATIONTEST theX-axisdirectionfor120minutes,and theY-axisdirection120minutes,the Z-axisdirection240minutesasvibration testingof1.1mmamplitudeand 33.30Hz/secoffrequency 以1.10mm和振幅和33.30Hz/sec振动频率 以X轴方向振动120分钟，Y轴方向振动 120分钟，Z轴方向振动240分钟. Nosignofdamage 3.耐久性测试（DURABILITY） 1 盐雾试验 SAIT SPRAYTEST 盐水喷雾试验：依GB1266-86 标准 SAIT SPRAY TEST:according to GB1266-8 蒸馏水(Distilled water)：一次蒸馏 (Once) PH6.5~7 喷雾量(Spray fog)：1.4me80cm²/h 压缩空气压力(Compressed air pressure)： 1Kgf/ cm² 温度(Temperature)：45°~47° 压力温度(Pressure)：35° 所有规格变华范 围初始值30% All characteristic range is 30% of the initial value 2 高温试验 HEAT TEST 在 50 +/- 2 °C环境中放 96 小时，再放在正 常环境中 30 分钟后进行测试 50 +/- 2 °C for 96 hours, after keep in normalconditionfor 30mimthe to test . 3温试验 HUMIDITYTEST 在40+2°C90-95%RH环境中放96小时， 再放在正常环境中30分钟后进行测试 40+2°C90-95%RHfor 96hours,after keep in normalconditionfor 30mimthe to test. 4低温试验 COLDTEST 在-40+2°C 环境中放96小时，再置放正常 环境中30分钟后进行测试 -40+2°Cfor 96hours,after keep in normal conditionfor 30mimthe to test. PIC 1 5150.0MHz H+V, Eff: 42.0% Back View 1.38dbi 1.05dbi 0.24dbi -0.53dbi -1.23dbi -1.58dbi -2.35dbi -2.89dbi -3.54dbi -4.69dbi -5.69dbi -6.78dbi -7.58dbi -8.69dbi -9.76dbi -10.2dbi -11.3dbi 5150.0MHz Total(E1-XZ), Max= -0.62dBi 5150.0MHz Total(E2-YZ), Max= 1.05dBi Total(H-XY), Max= -1.79dBi, CirD=7.14 5510.0MHz H+V, Eff: 56.4% Back View 5510.0MHz Total(E1-XZ), Max= -0.26dBi 5510.0MHz Total(E2-YZ), Max= 0.88dBi Total(H-XY), Max= 0.38dBi, CirD=4.07 1.1dbi -0.74dbi -2.59dbi -4.43dbi -6.27dbi -9.96dbi -11.8dbi -13.6dbi -14.6dbi -15.8dbi -17.6dbi -19.7dbi -20.6dbi -22.7dbi -24.5dbi -26.8dbi -28.5dbi 5810.0MHz H+V, Eff: 70.6% Back View 5810.0MHz Total(E1-XZ), Max= 0.84dBi 5810.0MHz Total(E2-YZ), Max= 1.17dBiTotal(H-XY), Max= 1.63dBi, CirD=2.75 1.63dbi 1.52dbi 1.48dbi 0.52dbi -0.02dbi -1.23dbi -2.23dbi -3.25dbi -4.25dbi -5.36dbi -7.52dbi -9.32dbi -11.25dbi -13.56dbi -15.68dbi -17.58dbi

TEST REPORT Applicant: Zhongshan Yueguang Intelligent Imaging Technology Co., Ltd Address: Zone C, R 306, #7, Zhangqi Technology Business Incubator, No. 70, Zhongshan City, China FCC ID: 2A8ZSH0010IGB Product Name: Remote Camera Assistant mini Standard(s): 47 CFR Part 15, Subpart E(15.407) ANSI C63.10-2013 KDB 789033 D02 General U-NII Test Procedures New Rules v02r01 The above equipment has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR230550738-00 Date Of Issue: 2023/9/5 Reviewed By: Calvin Chen Title: RF Engineer Approved By:Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230550738-00 Page 2 of 64 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR230550738-00 Page 3 of 64 CONTENTS T EST FACILITY .......................................................................................................................................... 2 DECLARATIONS .......................................................................................................................................... 2 DOCUMENT REVISION HISTORY .......................................................................................... 5 1. GENERAL INFORMATION .................................................................................................... 6 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................... 6 1.2 DESCRIPTION OF TEST CONFIGURATION ........................................................................................... 7 1.2.1 EUT Operation Condition: ............................................................................................................................. 7 1.2.2 Support Equipment List and Details .............................................................................................................. 8 1.2.3 Support Cable List and Details ...................................................................................................................... 8 1.2.4 Block Diagram of Test Setup ......................................................................................................................... 8 1.3 MEASUREMENT UNCERTAINTY .......................................................................................................... 9 2. SUMMARY OF TEST RESULTS .......................................................................................... 10 3. REQUIREMENTS AND TEST PROCEDURES .................................................................. 11 3.1 AC LINE CONDUCTED EMISSIONS .................................................................................................... 11 3.1.1 Applicable Standard ..................................................................................................................................... 11 3.1.2 EUT Setup.................................................................................................................................................... 12 3.1.3 EMI Test Receiver Setup ............................................................................................................................. 12 3.1.4 Test Procedure ............................................................................................................................................. 13 3.1.5 Corrected Amplitude & Margin Calculation ................................................................................................ 13 3.2 RADIATION SPURIOUS EMISSIONS .................................................................................................... 14 3.2.1 Applicable Standard ..................................................................................................................................... 14 3.2.2 EUT Setup.................................................................................................................................................... 15 3.2.3 EMI Test Receiver & Spectrum Analyzer Setup ......................................................................................... 15 3.2.4 Test Procedure ............................................................................................................................................. 16 3.2.5 Corrected Amplitude & Margin Calculation ................................................................................................ 16 3.3 EMISSION BANDWIDTH ..............…

Text truncated - open the document above for the full version.

China Certification ICT Co., Ltd (Dongguan) Report No.: CR230550738-00-TSP TEST SETUP PHOTOGRAPHS Radiated Emission Below 1GHz View Radiated Emission Above 1GHz View