2A94QVA-SP009Portable Smart Projector 1080P

1. The projector is connected to the internet: Click " " select and connect to the same network as the projector; 2. Click " " and select "VA-SP009-XXXXXX" to finish. Contents Projector Introduction 1.1 Packaging overview 1.2 Projector Introduction 1.3 Instruction of Remote Controller Use the Projector 2.1 Turn on/off projector 2.2 Focus adjustment 2.3 Bluetooth remote control pairing 2.4 Connect to the Wi-Fi network 2.5 Home interface 2.6 Instruction of the top navigation bar 2.7 Mirror function 2.8-3.4 Other functions FCC STATEMENT WEEE Compliance / Warranty Product Specifications 01-03 01 02 03 04-18 04 04-05 06 07 08 09 10-13 14-18 19-20 21 22 EN 1.1 Packaging overview 1.2 Projector lntroduction -01--02- Projector IntroductionProjector Introduction Projector Adaptor User ManualRemote Controller 1.3 Instruction of Remote Controller 2.1 Turn on/off the projector -03--04- Projector Introduction Bluetooth pairing mode Hold both "OK" and "Volume -" button five seconds to start remote control pairing mode Mouse mode Start: click mouse button Close: click navigation button Indicator light status Slow flash: unpaired mode Indicator light Power Button Direction navigation key Menu key OK key (Confirm key) When entering characters, the keyboard can be called up Home keyReturn key Mouse Volume -Volume + Focusing (Left and right direction keys to adjust focus) Turn on Press and hold the right on/off button for 3 seconds to turn on the device. Turn off Press and hold the power button for 1 second to turn off the device (Figure 1), or press and hold the power button on the remote control to power off. 2.2 Focus adjustment 2.2.1 Manual focus Press and hold the" "button of the remote control for 1 second. After the focusing circle appears, press and hold the "Left/Right" direction key of the remote control to focus manually. Use the Projector -05--06- Pairing method: 1. When the Bluetooth interface appears for the first time as the device is turned on, press the "OK + Volume -" button of the remote controller for about 5 seconds, the remote controller indicator flashes quickly, and the remote controller enters automatic pairing mode. 2. Enter the "Settings-Bluetooth" interface through the "Direction/Confirm" button on the body, press the "OK + Volume -"button of the remote controller for about 5 seconds. The remote control indicator flashes quickly and then click "Scan to find Device", the remote controller enters automatic pairing mode. 2.2.2 Auto focus method (1) The distance between the projector and the wall is about 0.5-1.5M, short press the " " button of the projector, the focus circle will pop up and auto focus will be performed, and the focus circle disappears after focusing; (2) Tilt the projector back and forth about 45 degrees, the focusing ring will pop up, and auto focus will be activated and complete itself. (3) Short press the " " button of the remote control, the focus ring will pop up, and the auto focus will be activated and complete itself. 2.3 Bluetooth remote control pairing Use the Projector Use the Projector -07--08- 2.4 Connect to the Wi-Fi network Use the Projector Enter the system, Settings - -> NETWORK--> select network and enter the password. 2.5 Home interface Use the Projector SEARCHHOME APPSVIDEO MUSIC SETTINGWEATHERHDMI WIFI OPTION -09--10- 2.6 Instruction of the top navigation bar 2.7 Mirror Function According to the devices of the mirror function, open the corresponding applications (Apple Screen Mirror / Android Mirror Apple wired Mirror), or you can open the relevant applications in "Settings-Mirror" interface to start Screen Mirror function. 2.7.1 Apple Mirror function iPhone device connection (1) Connect the device to the network; (2) Enter iPhone connection operation, there are two methods for iPhone ΍ Under Wi-Fi environment: Open the "Settings" of the mobile phone --- "Wireless LAN" Connect the mobile phone to the same network as the projector; ΎWithout Wi-Fi environment: Open the "Settings" of the mobile phone ---"Personal Hot spot" Turn on the hot spot and connect the projector to the hot spot; (3) Go back to the main interface of the phone, slide up to open the control panel, and click Airplay; (4) Select "VA-SP009-XXXXX", open "Mirror", complete -11--12- 2.7.2 Mac device connection2.7.3 Android screen mirror function 1. Open the "Android Projection Screen" application on the projector; 2. Connect the Android phone and the projector under the same Wi-Fi: 3. In the mobile phone "Settings" "NETWORK" "Wireless Screen projection", turn on the wireless projection function, and search for the device"VA-SP009-XXXXXX" (random number), select connection; 4. Most Androids can be found in the "Shortcut Bar > Screen Sharing/ Screen mirroring/projection screen/WLAN/wireless display/ multi-screen interaction" Search the device under the menu and connect. Please read the instruction carefully before operating the unit, the pictures are for reference only Model: VA-SP009 Portable Smart Projector 1080P User Manual MADE IN CHINA -13--14- 2.7.4 Wired screen mirror function (Android) 1. Enter: SETTING-->INPUT SOURCE-->TYPE-C, press “OK” 2. Connect phone and projector as picture shows. 3. Select “Agree” in the pop-up question of the phone. The phone which have to support Type-C data mirroring. e.g.: Samsung Galaxy S,Note;HUAWEI P/Mate;OPPO Find X VIVO X,iQOO;SONY Xpreria;OnePlus 9...... 2.8 Description of external equipment How to connect a USB flash drive 1. Insert the U disk into the USB port, open the "File Management" application, and the device can be identified. 2. You can also go to "MY APPS" ---> File Manager to check. -15--16- 2.9 Software upgrade Local upgrade Copy the downloaded firmware update.zip file to the root directory of the USB flash drive, and insert the USB flash drive (in FAT32 format); the system can automatically recognize the upgrade package and follow the prompts to upgrade (make sure the battery is sufficient when upgrading). Online upgrade In the "S…

Text truncated - open the document above for the full version.

ShenzhenAspironTechnologyCompanyLimited 3rdFloor,YibenBuilding,No.1063ChaguangRoad,XiliStreet,NanshanDistrict,Shenzhen,Guangdong, China FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 USA Date:09-08-2023 Ref:AttestationStatementsPart2.911(d)(5)(i)Filing FCCID:2A94QVA-SP009 ProductName:PortableSmartProjector1080P ModelName:VA-SP009 [ShenzhenAspironTechnologyCompanyLimited](“theapplicant”)certifiesthattheequipmentfor whichauthorizationissoughtisnot“covered”equipmentprohibitedfromreceivinganequipment authorizationpursuanttosection2.903oftheFCCrules. Sincerely, (Applicantsignature) (BobbyZou)

ShenzhenAspironTechnologyCompanyLimited 3rdFloor,YibenBuilding,No.1063ChaguangRoad,XiliStreet,NanshanDistrict,Shenzhen,Guangdong, China FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 USA Date:09-08-2023 Ref:AttestationStatementsPart2.911(d)(5)(ii)Filing FCCID:2A94QVA-SP009 ProductName:PortableSmartProjector1080P ModelName:VA-SP009 [ShenzhenAspironTechnologyCompanyLimited](“theapplicant”)certifiesthat,asofthedateofthe filingoftheapplication,theapplicantisnotidentifiedontheCoveredListasanentityproducing “covered”equipment. Sincerely, (Applicantsignature) (BobbyZou)

Shenzhen Aspiron Technology Company Limited 3rd Floor, Yiben Building, No.1063 Chaguang Road, Xili Street, Nanshan District, Shenzhen, Guangdong, China FederalCommunicationsCommission Authorizationand EvaluationDivision 7435OaklandMillsRoad Columbia,MD 21046 USA Date:02 -06-2023 Ref:2.911(d)(7)USA DesignatedAgentfor Serviceof Process FCC ID: 2A94QVA-SP009 ShenzhenAspironTechnologyCompanyLimited. (“the applicant”) certifiesthat,as of the dateof the filingof the application,VAVAINTERNATIONALINC.is our designatedU.S. agentfor serviceof process for the abovereferencedFCC ID.ShenzhenAspironTechnologyCompanyLimited.acceptsto maintain an agentfor no less thanone year afterthe granteehas terminatedall marketingand importationor the conclusionof any Commission-relatedproceedinginvolvingthe equipment. VAVAINTERNATIONALINC.accepts,as of the dateof the filingof the application,the obligationof the designatedU.S. agentfor serviceof processfor the abovereferencedFCC ID. DesignatedU.S. AgentInformation: Name:VAVAINTERNATIONALINC. FRN:0033406802 Address:20370TownCenterLaneSuite208Cupertino,CA 95014, UnitedStates FRN: 0033406802 ContactPerson:Ning Liang Tel.: 510-767-8112 Email:[email protected] Sincerely, [Applicantname]ShenzhenAspironTechnologyCompanyLimited. (Applicantprintedname)Bobby.zou (Applicantsignature) (U.S.agentsignature)

Agent Authorization Company: Shenzhen Aspiron Technology Company Limited Address: 3rd Floor, Yiben Building, No.1063 Chaguang Road, Xili Street, Nanshan District, Shenzhen, Guangdong, China Product Name: Portable Smart Projector 1080P Model Number(s): VA-SP009 Product Description: Portable Smart Projector 1080P We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: Sep. 08, 2023 Name: Bobby Zou Title: Approbation Manager Company: Shenzhen Aspiron Technology Company Limited

ShenzhenAspironTechnologyCompanyLimited 3rd Floor, Yiben Building,No.1063ChaguangRoad,Xili Street,NanshanDistrict,Shenzhen,Guangdong,China Office of EngineeringTechnology FederalCommunicationsCommission 7435 OaklandMills Road Columbia,MD 21046 USA Date: Sep. 08, 2023 Subject;Requestfor Confidentiality FCC ID: 2A94QVA-SP009 To WhomIt May Concern, Pursuantto the provisionsof the Commission’s rules Title 47 Sections§0.457 and §0.459,we are requestingthe Commissionto withholdthe followingattachment(s)as confidential documentsfrom public disclosureindefinitely. Thesedocumentscontaindetailedsystemand equipmentdescriptionsand are consideredas proprietaryinformationin operationof the equipment.The public disclosureof these documents might be harmfulto our companyand would give competitorsan unfair advantagein the market. SchematicDiagram Block Diagram OperationalDescription Parts List AntennaSpecificationFCC_Confidential SoftwareSecurityDescription In additionalto abovementioneddocuments,in order to complywith the marketingregulations in Title 47 CFR §2.803 and the importationrules in Title 47 CFR §2.1204,while ensuringthat businesssensitiveinformationremainsconfidentialuntil the actualmarketingof newly authorizeddevices,we requestShort Term Confidentialityof the followingattachment(s); ExternalPhotos Test Setup Photos InternalPhotos User Manual For 45 days, pursuantto PublicNoticeDA 04-1705. OR For 180 days pursuantto KDB 726920D01. It is our understandingthat all measurementtest reports,FCC ID label formatand correspondenceduringthe certificationreviewprocesscannotbe grantedas confidential documentsand this informationwill be availablefor public reviewonce the grant of equipment authorizationis issued. Sincerely, Signature: Name: BobbyZou Title:ApprobationManager

Report No.: AGC13454230712AP02 Page 1 of 4 EXTERNAL PHOTOS All VIEW OF EUT TOP VIEW OF EUT Report No.: AGC13454230712AP02 Page 2 of 4 BOTTOM VIEW OF EUT FRONT VIEW OF EUT Report No.: AGC13454230712AP02 Page 3 of 4 BACK VIEW OF EUT LEFT VIEW OF EUT Report No.: AGC13454230712AP02 Page 4 of 4 RIGHT VIEW OF EUT ADAPTER VIEW OF EUT ****************************************End of Report*************************************

FCC ID Label Location 10mm*15mm FCC ID: 2A94QVA-SP009

Report No.: AGC13454230712AP02 Page 1 of 5 INTERNAL PHOTOS OPEN VIEW OF EUT (FIGURE 1) OPEN VIEW OF EUT (FIGURE 2) Report No.: AGC13454230712AP02 Page 2 of 5 OPEN VIEW OF EUT (FIGURE 3) OPEN VIEW OF EUT (FIGURE 4) Report No.: AGC13454230712AP02 Page 3 of 5 OPEN VIEW OF EUT (FIGURE 5) OPEN VIEW OF EUT (FIGURE 6) Report No.: AGC13454230712AP02 Page 4 of 5 INTERNAL VIEW OF EUT (FIGURE 1) INTERNAL VIEW OF EUT (FIGURE 2) 2.4G&5G WIFI ANT.1 2.4G&5G WIFI ANT.2 BT Antenna Report No.: AGC13454230712AP02 Page 5 of 5 INTERNAL VIEW OF EUT (FIGURE 3) INTERNAL VIEW OF EUT (FIGURE 4) ****************************************End of Report*************************************

RF EXPOSURE EVALUATION 1. PRODUCT INFORMATION FCC ID 2A94QVA-SP009 Product Description Portable Smart Projector 1080P Model Name VA-SP009 Frequency Band (Operating) WLAN: 2.412GHz ~ 2.462GHz WLAN: 5.18GHz ~ 5.32GHz / 5.50GHz ~ 5.70GHz WLAN: 5.745GHz ~ 5825GHz Bluetooth: 2.402GHz ~ 2.480GHz Others Device Category Portable (<20cm separation) Mobile (≥20cm separation) Antenna Diversity Single antenna Multiple antennas Max. Output Power(Average) 2.4G BT: 7.876dBm 2.4G WIFI: 14.29dBm 5G WIFI: 13.98dBm Antenna Gain 2.4GHz BT: 2.3dBi; 2.4GHz WIFI: Ant 1:1.6dBi; Ant 2: 1.8dBi 5GHz WIFI: Ant 1: 2.1dBi; Ant 2: 2.3dBi Minimum Assessment Distance 20cm Evaluation Applied MPE Evaluation SAR Evaluation Evaluation Result Pass 2. PORTABLE DEVICE EVALUATION METHOD AND LIMIT Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] [if(GHz)] s 3.0 for 1-g SAR and ñ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz.  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50mm) ( f(MHz)/150)] mW, at 100MHz to 1500 MHz; b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)-10] mW at > 1500 MHz and ≤6 GHz; 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by 1/2 for test separation distances ñ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. 3. MOBILE DEVICE EVALUATION METHOD AND LIMIT Human exposure to RF emissions from mobile devices (47 CFR §2.1091) may be evaluated based on the MPE limits adopted by the FCC for electric and magnetic field strength and/or power density, as appropriate, since exposures are assumed to occur at distances of 20 cm or more from persons. LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE Frequency Range (MHz) E-field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Time |E| 2 , |H| 2 or S (Minutes) 0.3 -- 1.34 614 1.63 (100)* 30 1.34 -- 30 824/f 2.19/f (180/f 2 )* 30 30 -- 300 27.5 0.073 0.2 30 300 -- 1500 -- -- f/1500 30 1500 -- 100,000 -- -- 1.0 30 *Note: 1. f= Frequency in MHz * Plane-wave Equivalent Power Density 2. The averaging time for General Population/Uncontrolled exposure to fixed transmitters is not applicable for mobile and portable transmitters. See 47 CFR §§2.1091 and 2.1093 on source-based time-averaging requirement for mobile and portable transmitters. S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 4. MEASUREMENT RESULT A minimum test separation distance ≥ 20 cm is required between the antenna and radiating structures of the device and nearby persons to apply mobile device exposure limits. The distance must be at least 20 cm and fully supported by the operating and installation configurations of the transmitter and its antenna(s), according to the source-based time-averaged maximum power requirements of § 2.1091(d)(2). In cases where cable losses or other attenuations are applied to determine compliance, the most conservative operating configurations and exposure conditions must be evaluated. 2.4G BT: Antenna Gain=2.3dBi (Numeric 1.70), π=3.14 2.4G WLAN-Ant.1: Antenna Gain=1.6dBi (Numeric 1.45), π=3.14 2.4G WLAN-Ant.2: Antenna Gain=1.8dBi (Numeric 1.51), π=3.14 5G WLAN-Ant.1: Antenna Gain=2.1dBi (Numeric 1.62), π=3.14 5G WLAN-Ant.2: Antenna Gain=2.3dBi (Numeric 1.70), π=3.14 Note： 1. Calculate the SAR test to eliminate thresholds from chapter 2 conditions "3" formula. 2. Max Power (mW) = 10^(Max power (dBm)/10) 3. The 2.4G and 5G WIFI can transmit simultaneously: 4. 0.012/1+0.013/1=0.025＜1 Test Mode Test Frequency (MHz) Max. Output Power (dBm) Max. Output Power (mW) Power Density (mW/cm 2 ) Measurement Limit (mW/cm 2 ) 2.4G BT(BR/EDR) 2480 7.876 6.132 0.002 1 2.4G BT(BLE) 2440 0.943 1.243 0.0004 1 2.4GWIFI Ant 1 2412 14.29 26.853 0.008 1 2.4GWIFI Ant 2 2412 12.99 19.907 0.006 1 2.4GWIFI MIMO 2422 16.00 39.811 0.012 1 5GWIFI Ant 1 5240 13.13 20.559 0.007 1 5GWIFI Ant 2 5240 13.98 25.003 0.008 1 5GWIFI MIMO 5240 15.92 39.084 0.013 1

Page 1 of 70 FCC Test Report Report No.: AGC13454230712FR01 FCC ID : 2A94QVA-SP009 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Portable Smart Projector 1080P BRAND NAME : VAVA MODEL NAME : VA-SP009 APPLICANT : Shenzhen Aspiron Technology Company Limited DATE OF ISSUE : Sep. 08, 2023 STANDARD(S) : FCC Part 15 Subpart C §15.247 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC13454230712FR01 Page 2 of 70 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Sep. 08, 2023 Valid Initial Release Report No.: AGC13454230712FR01 Page 3 of 70 TABLE OF CONTENTS 1. VERIFICATION OF CONFORMITY .................................................................................................................. 5 2. GENERAL INFORMATION .............................................................................................................................. 6 2.1. PRODUCT DESCRIPTION ........................................................................................................................ 6 2.2. TABLE OF CARRIER FREQUENCYS ....................................................................................................... 6 2.3. RECEIVER INPUT BANDWIDTH .............................................................................................................. 7 2.4. EXAMPLE OF A HOPPING SEQUENCY IN DATA MODE ......................................................................... 7 2.5. EQUALLY AVERAGE USE OF FREQUENCIES AND BEHAVIOUR ......................................................... 7 2.6. RELATED SUBMITTAL(S) / GRANT (S) .................................................................................................... 8 2.7. TEST METHODOLOGY ............................................................................................................................. 8 2.8. SPECIAL ACCESSORIES ......................................................................................................................... 8 2.9. EQUIPMENT MODIFICATIONS ................................................................................................................. 8 2.10. ANTENNA REQUIREMENT..................................................................................................................... 8 3. MEASUREMENT UNCERTAINTY ................................................................................................................... 9 4. DESCRIPTION OF TEST MODES ................................................................................................................. 10 5. SYSTEM TEST CONFIGURATION ................................................................................................................ 11 5.1. CONFIGURATION OF EUT SYSTEM ...................................................................................................... 11 5.2. EQUIPMENT USED IN TESTED SYSTEM .............................................................................................. 11 5.3. SUMMARY OF TEST RESULTS .............................................................................................................. 11 6. TEST FACILITY .............................................................................................................................................. 12 7. PEAK OUTPUT POWER ................................................................................................................................ 13 7.1. MEASUREMENT PROCEDURE ............................................................................................................. 13 7.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 13 7.3. LIMITS AND MEASUREMENT RESULT .................................................................................................. 14 8. 20DB BANDWIDTH ........................................................................................................................................ 19 8.1. MEASUREMENT PROCEDURE ............................................................................................................. 19 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 19 8.3. LIMITS AND MEASUREMENT RESULTS ............................................................................................... 20 9. CONDUCTED SPURIOUS EMISSION........................................................................................................... 25 9.1. MEASUREMENT PROCEDURE ............................................................................................................. 25 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 25 9.3. MEASUREMENT EQUIPMENT USED .................................................................................................... 25 9.4. LIMITS AND MEASUREMENT RESULT .................................................................................................. 25 10. RADIATED EMISSION ................................................................................................................................. 46 10.1. MEASUREMENT PROCEDURE ........................................................................................................... 46 Report No.: AGC13454230712FR01 Page 4 of 70 10.2. TEST SETUP ......................................................................................................................................... 48 10.3. LIMITS AND MEASUREMENT RESULT ............................................................................................... 49 10.4. TEST RESULT........................................................................................................................................ 49 11. NUMBER OF HOPPING FREQUENCY .................................…

Text truncated - open the document above for the full version.

ShenzhenGolden-Resource ElectronicCo.,Ltd. SPECIFICATIONFORAPPROVAL Date 2023/08/02 FileNo 23080201 Revision 1.0 CUSTOMER:ShenzhenSuichenTechnologyCo.,Ltd CUSTOMERNO: 1.SD.3711.700172/1.SD.3711.700173/1.SD.3711.700174 PARTNAME: WiFi1Antenna/WiFi2Antenna/BTAntenna Antennatype： FPCAntenna SUPPLIERNO: YJWO1.029.064.301A/YJWO1.029.064.302A/YJW01.029.064.303A Date:Q"TY:PCS CUSTOMERAPPROVEDBY APPROVALCHIEFSUPERVISOR SUPPLIERSIGNATURE APPROVALCHECKDESIGN ChenGuoqiangXieLiChenXingcheng YJ-RD-F04-A add：17A-03A,BlockB,NanxianCommercialPlaza,MeilongRoad,LonghuaNewDistrict,Shenzhen SpecItem NO . 内容 （Contents） Numberof Page PageCode 1SpecCover11 2SpecItem12 3Drawing33~5 4AntennaSpecification36~8 5SParameter39~11 6PassiveTest612~17 7ActiveTest118 8AntennaProfile519~23 9MaterialCertificate3424~57 10RoHSTestReport**** 11N/AN/AN/A 12--- 13--- add：17A-03A,BlockB,NanxianCommercialPlaza,MeilongRoad,LonghuaNewDistrict,Shenzhen RoHSI CUSTOMER PARTNO DESCRIPTION InitialIssue ModifyLineLengthAndColor DATE 2021-03-23 2021-04-09 PARTNO.:YJW01.029.064.301A APPROVEDBYCHECKEDBYDESIGNEDBY G再司 llNITS:mm ShenzhenGolden-ResourceElectronicCo.,Ltd. PARTNAME:WiFi1Antenna DATE:2021-04·09 T 口 Ieranee x.x±0.50 YinTao LiaoMingyuLvSenhuaSCALE:1/1 X.XX±0.15 REVISION:AX" 土 3• ElE 口 150.0士4.0 2 3 回 日 3 FPCB40.0*7.3MMFPCBFPC1OOOXA.P01 叫 2 CoaxialCableO.D.0.81日lackO.D.0.81 COA1000XA.P01 MiniConnectorAuPlated3代 CuTER1OOOXA.P01 NOIPARTNAMEDESCRIPTION MaterialPa此Number Q.TY 阳 － A － A 40.0 阳 － A － A CUSTOMER PARTNO DESCRIPTION InitialIssue DATE 2021-03-23 ModifyLineColo「 2021-04-09 ElE 口｜ Cl 回日 ShenzhenGolden-ResourceElectronicCo.,Ltd. NOIPARTNAMEDESCRIPTION Mate『ialPa此Numbe『 Q.TY 5 _l 67 T口le阻nee Al x.X土 0.50 X.XX±0.15 X'土3' RoHSI 40.0 30.0±3.0 3 FPCB 40.0*9.0MM FPCB FPC1OOOXA.P01 2 CoaxialCableO.D.0.81日lack O.D.0.81 GOA1OOOXA.P01 MiniConnector AuPlated3代 CuTER1OOOXA.P01 PARTNAME:WiFi2Antenna PARTNO.:YJW01皿9.064.302A APPROVEDBYCHECKEDBYDESIGNEDBY ＠司 YinTao LiaoMingyu LvSenhua 111\11Tmm SCALE:1/1 目EVISION·A SCALE:1月 x.x EE 口｜ 110.0±4.0 一 B 39.6 口｜ 日 ShenzhenGolden-ResourceElectronicCo.,Ltd. PARTNAME:BTAntenna PARTNO.:YJW01.029.064.303A DATE:2021-04-09 APPROVEDBYCHECKEDBYDESIGNEDBY＠司 Tolerance TIJJl'Tl>:mm YinTao LiaoMingyc LvSenhua 言 目Vll':ll'IN·A ±0.50 x.xx土0.15 x· 土3• RoHSI CUSTOMER PARTNO DESCRIPTION InitialIssue ModifyLineColor DATE 2021-03-23 2021-04-09 阳 － A － A Al AL3 FPCB 39.6*5.7MM FPCB FPC1OOOXA.P01 2 Co创alCable MiniConnecto『 0.D.0.81Black 0.D.0.81 COA1OOOXA.P01 AuPl自恒d3 代 Cu TER1000XA.P01 NO PARTNAME DESCRIPTION Mate「ial PartNumbe「 Q.TY AntennaSpecificationWiFi1 ElectricalProperties Frequency 2.4-2.5GHz 5.15-5.85GHz Impedance50OhmNominal [email protected] V.S.W.R [email protected] Gain [email protected] [email protected] RadiationOmni-directional PolarizationLinear PhysicalProperties Connector3GenerationIPEX CableTypeO.D.0.81mm CableLength150mm CableColorBlack OperatingTemp.-40~+85 ̊C StorageTemp/Humidity25±5 ̊C/<70% add：17A-03A,BlockB,NanxianCommercialPlaza,MeilongRoad,LonghuaNewDistrict,Shenzhen AntennaSpecificationWiFi2 ElectricalProperties Frequency 2.4-2.5GHz 5.15-5.85GHz Impedance50OhmNominal [email protected] V.S.W.R [email protected] Gain [email protected] [email protected] RadiationOmni-directional PolarizationLinear PhysicalProperties Connector3GenerationIPEX CableTypeO.D.0.81mm CableLength30mm CableColorBlack OperatingTemp.-40~+85 ̊C StorageTemp/Humidity25±5 ̊C/<70% add：17A-03A,BlockB,NanxianCommercialPlaza,MeilongRoad,LonghuaNewDistrict,Shenzhen AntennaSpecificationBT ElectricalProperties Frequency 2.4-2.5GHz Impedance50OhmNominal V.S.W.R2.0Max Gain 2.3dBi RadiationOmni-directional PolarizationLinear PhysicalProperties Connector3GenerationIPEX CableTypeO.D.0.81mm CableLength110mm CableColorBlack OperatingTemp.-40~+85 ̊C StorageTemp/Humidity25±5 ̊C/<70% add：17A-03A,BlockB,NanxianCommercialPlaza,MeilongRoad,LonghuaNewDistrict,Shenzhen add：17A-03A,BlockB,NanxianCommercialPlaza,MeilongRoad,LonghuaNewDistrict,Shenzhen Agilent E5071B S Parameter Test// WIFI(1) Antenna add：17A-03A,BlockB,NanxianCommercialPlaza,MeilongRoad,LonghuaNewDistrict,Shenzhen Agilent E5071B S Parameter Test// WIFI(2) Antenna add：17A-03A,BlockB,NanxianCommercialPlaza,MeilongRoad,LonghuaNewDistrict,Shenzhen Agilent E5071B S Parameter Test// BT Antenna add：17A-03A,BlockB,NanxianCommercialPlaza,MeilongRoad,LonghuaNewDistrict,Shenzhen AntennaPassiveTest Z Y X Y Z X add：17A-03A,BlockB,NanxianCommercialPlaza,MeilongRoad,LonghuaNewDistrict,Shenzhen PassiveTestForWIFI(1)2.4G FreqEffiEffiGain (MHz)(%)(dB)(dBi) 2400 47.3-3.31.2 2410 48.5-3.11.3 2420 48.5-3.11.4 2430 50.0-3.01.5 2440 50.3-3.01.5 2450 52.5-2.81.6 2460 52.7-2.81.6 2470 51.7-2.91.6 2480 51.4-2.91.6 2490 48.6-3.11.4 2500 48.5-3.11.4 add：17A-03A,BlockB,NanxianCommercialPlaza,MeilongRoad,LonghuaNewDistrict,Shenzhen PassiveTestForWiFi（1）5.8G FreqEffiEffiGain (MHz)(%)(dB)(dBi) 5150 34.4-4.60.1 5200 36.3-4.40.2 5250 37.2-4.30.5 5300 39.9-4.01.7 5350 40.3-3.91.8 5400 41.2-3.92.1 5450 40.3-3.91.9 5500 39.1-4.11.5 5550 38.5-4.10.9 5600 35.7-4.50.1 5650 34.9-4.60.1 5700 34.4-4.60.1 5750 34.9-4.60.1 5800 35.7-4.50.1 5850 36.3-4.40.2 add：17A-03A,BlockB,NanxianCommercialPlaza,MeilongRoad,LonghuaNewDistrict,Shenzhen PassiveTestForWIFI(2)2.4G FreqEffiEffiGain (MHz)(%)(dB)(dBi) 2400 37.2-4.30.4 2410 38.5-4.10.7 2420 39.4-4.00.8 2430 40.7-3.91.2 2440 40.7-3.91.4 2450 42.5-3.71.7 2460 42.9-3.71.8 2470 41.7-3.81.6 2480 41.1-3.91.6 2490 40.6-3.91.0 2500 40.5-3.90.9 add：17A-03A,BlockB,NanxianCommercialPlaza,MeilongRoad,LonghuaNewDistrict,Shenzhen PassiveTestForWiFi（2）5.8G FreqEffiEffiGain (MHz)(%)(dB)(dBi) 5150 31.2-5.1-0.1 5200 36.2-4.41.0 5250 36.7-4.41.5 5300 38.9-4.11.8 5350 39.9-4.02.0 5400 40.4-3.92.3 5450 40.3-3.92.1 5500 37.7-4.21.7 5550 37.3-4.31.6 5600 35.4-4.50.5 5650 34.4-4.60.1 5700 31.2-5.1-0.1 5750 34.4-4.60.1 5800 35.4-4.50.5 5850 36.2-4.41.0 add：17A-03A,BlockB,NanxianCommercialPlaza,MeilongRoad,LonghuaNewDistrict,Shenzhen PassiveTestForBT2.4G FreqEffiEffiGain (MHz)(%)(dB)(dBi) 2400 33.3-4.80…

Text truncated - open the document above for the full version.

Report No.: AGC13454230712AP01 Page 1 of 3 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 1GHz RADIA…

Text truncated - open the document above for the full version.