2A9FA-07-0025-915-AThe portable reader T1074 is a user interface for the Ground Engaging Tool IoT sensor. Powered by a rechargeable battery it is using GSFK modulation at a rate of 250 kbps for bidirectional wireless communication in the 915MHz ISM band.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. PORTABLE READER Quick User Guide Warning: Any changes or modifications not expressively approved by CR Mining could void the user’s authority to operate this equipment For assistance, email [email protected] or call (+61) 1300 33 8482 F1 [➕] Add sensor to digger and activate. F2 [] Search for sensors. F3 [] Return to Home menu or [] Escape out of current function. F4 [➖] Remove a sensor from the digger and deactivate it. NOTE: Hold down the centre button ◎ for 3 seconds to turn off the Portable Reader Available Function Options Screen Heading Battery Level Indicator Menu List Function Options Function Buttons Identifies which screen the Portable Reader is currently on When the Battery level is low , connect to GET Trakka charger List of options for the user to select from Available function options appear as F1 - F4 F1 - F4 activate t he corresponding Function Navigation Pad Navigate the ‘ Screen Options ’ and select using the center button ◎ Connect the supplied GET Trakka DC Charger to this port. Green ‘Power’ LED =connected Orange ‘Charge’ LED = c harging DC Power In Portable reader overview For assistance, email [email protected] or call (+61) 1300 33 8482 Activate / Deactivate Sensors The following is a quick overview of the procedure to activate and deactivate Sensors with the GET Trakka Portable Reader. 1. Select ‘Digger List’, using center button ◎ 2. Select ‘SHOVEL13’ From Digger List using ◎ 3. Select ‘Lip Shroud’ by pressing then ◎ 4. Use and to navigate. Press ‘F1’ to find nearby Sensors 5. Activate ‘80166’ by pressing ◎ 6. GET index position is ‘filled’ to confirm activation 7. Once all index positions are ‘filled’, ‘✓’ is displayed 9. GET index position is ‘cleared’ to confirm deactivation 8. Use and to navigate. ‘F4’ then ◎ to deactivate a Sensor For assistance, email [email protected] or call (+61) 1300 33 8482 Search Mode Search Mode is used to detect and locate detached GET in the field. It will only be enabled once the Search Antenna has been connected to the Portable Reader. 1. Navigate to ‘Search for GET’ using . Select it by pressing the center button ◎ 2. Select the digger that is missing a component using ◎ 3. Navigate to the missing component by using and . Select it using ◎ 4. Navigate using and to select the missing Index Position 5. Search for the missing Sensor by pressing F2 6. Use the search bar to detect and locate the missing GET component. The bar will grow as the signal gets stronger.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required PORTABLE READER User Manual Rev 6.0 Jan 2023 Warning: Any changes or modifications not expressively approved by CR Mining could void the user’s authority to operate this equipment 1 TABLE OF CONTENTS 1. INTRODUCTION ................................................................................................................................................... 2 2. SENSOR TYPES .................................................................................................................................................... 3 2.1 GET SENSORS ................................................................................................................................................................ 3 2.2 REFERENCE SENSORS ....................................................................................................................................................... 3 2.3 BUCKET SENSORS ............................................................................................................................................................ 3 3. GET SENSOR OVERVIEW ...................................................................................................................................... 4 3.1 ACTIVE SENSORS ............................................................................................................................................................. 4 3.2 INACTIVE SENSORS .......................................................................................................................................................... 4 4. GET SENSOR INSTALLATION ................................................................................................................................ 5 5. PORTABLE READER OVERVIEW ........................................................................................................................... 6 6. POWER AND CHARGING ..................................................................................................................................... 8 6.1 POWER ......................................................................................................................................................................... 8 6.2 CHARGING ..................................................................................................................................................................... 8 7. KEYPAD AND LCD TOUCH SCREEN FUNCTIONS.................................................................................................... 8 8. DIGGER LIST ...................................................................................................................................................... 11 9. ADD GET SENSORS TO A DIGGER ....................................................................................................................... 12 10. DUPLICATE GET SENSORS .................................................................................................................................. 14 11. REMOVE GET SENSORS ..................................................................................................................................... 16 12. SEARCH SENSORS .............................................................................................................................................. 18 13.1 SEARCH ACTIVE SENSORS ............................................................................................................................................... 18 13.2 SEARCH INACTIVE (ASLEEP) SENSORS ................................................................................................................................ 18 13.3 SEARCH FOR LOST SENSORS ............................................................................................................................................ 19 13.4 SEARCH PROCESS .......................................................................................................................................................... 20 13. SETTINGS .......................................................................................................................................................... 22 14.1 BACKLIGHT MODE......................................................................................................................................................... 22 14.2 CALIBRATE TOUCH SENSOR ............................................................................................................................................. 22 14.3 RESET TOUCH SENSOR ................................................................................................................................................... 22 2 1. Introduction The GET Trakka system provides real-time actionable information to optimise mine-critical assets. GET Trakka monitors the real-time operation of digger buckets and GET, detects component loss when they occur and locates GET before they enter the downstream process. GET components include teeth, adapters, lip shrouds and side bars that make up a full protective wear package on a digger bucket. The key hardware components of a GET Trakka system are; a) GET Sensors – battery powered radio frequency sensors embedded into the GET components and mounted to digger buckets. b) Portable Reader – portable reader t…

Text truncated - open the document above for the full version.

T1074 USER MANUAL January 2023 PORTABLE READER For assistance, email [email protected] or call (+61) 1300 33 8482 The Portable Reader is a device used to wirelessly communicate with GET Trakka Sensor Tags in order to activate / deactivate tags as required. In the case of a GET breakage the Portable Reader can be used in search mode to locate a missing component by locking on to an RFID signal using a high gain external antenna. The rugged hand held unit is designed for mine duty in all weather applications and features a high contrast LCD screen for bright daylight and night time use with large tactile buttons. The integrated 2.9Ah rechargeable lithium ion battery provides days of continuous use, while the fast 250 kbps transmissions rates and strong active RFID signal allow the user to check the nearby sensors in real-time and view the sensor traffic and health information without disruptions to a live system. T1074 Operating Bandwidth 920 – 925 MHz Channels 4 Selectable Channel Spacing 1 MHz RFID Type Active Transmitter / Receiver / Transceiver Transceiver Transmission Power 10 mW (Max) - Fixed Transmission Rate 250 kbps Transmission Frequency / Period Manual Duty Cycle N/A Battery Type 3.6 V Rechargeable Lithium - Ion Nominal Capacity 2.9 Ah Product Operating Temperature -10 to +70 °C Dimensions 105 mm W x 275mm H x 104mm D Weight 750 g Accessories Wall charger (12V), High-gain patch antenna (BNC), Rugged carry case. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required. Warning: Any changes or modifications not expressively approved by the grantee could void the user's authority to operate this equipment.

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 04-11-2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: 2A9FA-07-0025-915-A FRN: 0033098336 CR Mining certifies that, as of the date of the filing of the application, Capitol Corporate Services, Inc is our designated U.S. agent for service of process for the above referenced FCC ID. CR Mining accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Capitol Corporate Services, Inc accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Name: Capitol Corporate Services, Inc Address: 698 12th St SE Ste 200, Salem OR 97301 Contact Person: Yvette Cleveland Tel.: 800-345-4647 Email: [email protected] Sincerely, CR Mining Capitol Corporate Services, Inc JULIEN LOPEZ Yvette Cleveland, Assistant Secretary

Rev 1/26/2023 CR Mining 3/271 Treasure Rd N, Welshpool WA 6106 Australia Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 03-01-2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2A9FA-07-0025-915-A Julien Lopez (“CR Mining”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Julien Lopez

Rev 1/26/2023 CR Mining 3/271 Treasure Rd N, Welshpool WA 6106 Australia Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 03-01-2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2A9FA-07-0025-915-A Julien Lopez (“CR Mining”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Julien Lopez

EMC Technologies Pty Ltd, 176 Harrick Road, Keilor Park VIC 3042 Australia www.emctech.com.au To: Federal Communications Commission Attention: Certification Officer Date: April 21, 2023 EMC Ref: M2211024 Subject: FCC FILING – FCC ID: 2A9FA-07-0025-915-A (Original Certification) CR Mining is applying for FCC certification of a portable reader. The portable reader T1074 is a user interface for the Ground Engaging Tool IoT sensor. Powered by a rechargeable battery it is using GSFK modulation at a rate of 250 kbps for bidirectional wireless communication in the 915MHz ISM band. EUT Transmitter Details: Type: User Interface Operating Freq: 903 to 927 MHz Antenna: 4 SMD antennas EMC Technologies is acting as agent CR Mining in this application. Regards _____________ Shabbir Ahmed CEO EMC Technologies Pty Ltd 176 Harrick Road, Keilor Park, VIC 3042 Australia Ph: +61 3 9365 1000 www.emctech.com.au EMC Technologies Pty Ltd ABN 82 057 105 549 176 Harrick Road, Keilor Park, VIC 3042 Australia Ph: + 613 9365 1000 Fax: + 613 9331 7455 Email: [email protected]

Connect with us www.CRmining.com Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 16/01/2023 SUBJECT: FCC Application for FCC ID: 2A9FA-07-0025-915-A To Whom It May Concern: We, CR Mining, hereby authorize Shabbir Ahmed at EMC Technologies Pty Ltd to act on our behalf, to apply to the Federal Communications Commission for FCC approval of our equipment. Any and all acts carried out by Shabbir Ahmed at EMC Technologies on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Julien Lopez Production Engineer (Electronics)

Connect with us www.CRmining.com Federal Communications Commission Authorization and Evaluation Division Date: 16/01/2023 Conf identiality Request regarding application f or certif ication of FCC ID: 2A9FA-07-0025-915-A, Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request conf idential treatment of inf ormation accompanying this application as outlined below: Exhibit Type for 2A9FA-07-0025-915-A File Name Schematic 2A9FA-07-0025-915-A.Portable Reader-Hand Held GET Tag Controller Part1_Schematic.pdf Schematic 2A9FA-07-0025-915-A.Portable Reader-Hand Held GET Tag Controller Part 2_Schematic.pdf Block Diagram 2A9FA-07-0025-915-A.Portable Reader-HW_Architec- ture.pdf Operational Description 2A9FA-07-0025-915-A.Portable Reader-FCC Operation Description_Specif ication.pdf The above materials contain trade secrets and proprietary inf ormation not customarily released to the public. The public disclosure of these materials may be harmf ul to the applicant and provide unjustif ied benef its to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompany- ing documentation will not be made bef ore the date of the Grant f or this application. Sincerely, Julien Lopez Production Engineer (Electronics)

Page 1 of 4 EMC ENGINEERS & LABORATORIES EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South, Victoria, 3136, Australia Telephone: +61 3 9761 5888 Facsimile: +61 3 8761 6547 Email: [email protected] ABN: 49 112 221 333 Photograph Annex A: External - EUT Photographs CR Mining T1074 Portable Reader REPORT: E2211-1609D-2 Annex A DATE: April, 2023 EMC Bayswater Test Report E2211-1609D-2 Annex A Page 2 of 4 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photographs Number Photograph Description 1 EUT – External views 2 3 4 5 6 7 8 9 10 EUT – External antenna connector 11 EUT – USB port (Factory use only) 12 EUT – Battery charger port EMC Bayswater Test Report E2211-1609D-2 Annex A Page 3 of 4 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 1 Photograph 2 Photograph 3 Photograph 4 Photograph 5 Photograph 6 EMC Bayswater Test Report E2211-1609D-2 Annex A Page 4 of 4 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 7 Photograph 8 Photograph 9 Photograph 10 Photograph 11 Photograph 12

2A9FA-07-0025-915-A Label Draft Proposed Label Detail 1 1 THE DESIGN AND TECHNICAL INFORMATION DETAILED ON THIS DRAWING IS THE EXCLUSIVE PROPERTY OF CQMS RAZER PTY LTD. IT IS ISSUED ON THE STRICT CONDITION THAT, EXCEPT WITH OUR WRITTEN PERMISSION, IT MUST NOT BE USED FOR ANY PURPOSE OTHER THAN ITS STATED PURPOSE OF ISSUE. PH: 1800 987 525 WEB: www.crmining.com Page of REVISIONS REVDESCRIPTIONDATEAPPROVED NOTES: The product will have the label on the back section as illustrated below. The proposed label will be using the ORAGET 3551G PVC film, Silicone coated paper 86x14 (mm) in size. The label will be marked the FCC ID: 2A9FA-07-0025-915-A, and the compliance statement from FCC Part 15.19. 1Draft23/01/2023 NH 1Draft23/01/2023 NH Proposed label area Proposed label area Handheld reader FCC ID: 2A9FA-07-0025-915-A (1) This device may cause interference; and This device complies with Part 15 of the FCC Rules. Operation is subjected to the following two conditions: (2) This device must accept any interference, including interference that may cause undesired operations of the device FCC ID: 2A9FA-07-0025-915-A (1) This device may cause interference; and This device complies with Part 15 of the FCC Rules. Operation is subjected to the following two conditions: (2) This device must accept any interference, including interference that may cause undesired operations of the device

Page 1 of 7 EMC ENGINEERS & LABORATORIES EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South, Victoria, 3136, Australia Telephone: +61 3 9761 5888 Facsimile: +61 3 8761 6547 Email: [email protected] ABN: 49 112 221 333 Photograph Annex B: Internal - EUT Photographs CR Mining T1074 Portable Reader REPORT: E2211-1609D-2 Annex B DATE: April, 2023 EMC Bayswater Test Report E2211-1609D-2 Annex B Page 2 of 7 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photographs Number Photograph Description 1 EUT – Internal views 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 EMC Bayswater Test Report E2211-1609D-2 Annex B Page 3 of 7 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 1 Photograph 2 Photograph 3 Photograph 4 Photograph 5 Photograph 6 EMC Bayswater Test Report E2211-1609D-2 Annex B Page 4 of 7 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 7 Photograph 8 Photograph 9 Photograph 10 Photograph 11 Photograph 12 EMC Bayswater Test Report E2211-1609D-2 Annex B Page 5 of 7 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 13 Photograph 14 Photograph 15 Photograph 16 Photograph 17 Photograph 18 EMC Bayswater Test Report E2211-1609D-2 Annex B Page 6 of 7 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 19 Photograph 20 Photograph 21 Photograph 22 Photograph 23 Photograph 24 EMC Bayswater Test Report E2211-1609D-2 Annex B Page 7 of 7 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 25 Photograph 26 Photograph 27

Page 1 of 7 EMC ENGINEERS & LABORATORIES EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South, Victoria, 3136, Australia Telephone: +61 3 9761 5888 Facsimile: +61 3 8761 6547 Email: [email protected] ABN: 49 112 221 333 RF Radiation Exposure Evaluation In accordance with: CFR47 FCC Part 2, Subpart J, 2.1093 FCC KDB 447498 D01 v06 CR Mining T1074 Portable Reader FCC ID: 2A9FA-07-0025-915-A REPORT: E2211-1609D-3 DATE: April, 2023 EMC Bayswater Test Report E2211-1609D-3 Page 2 of 7 Prepared by: Approved by: 12/04/2023 13:08 Adnan Zaman (EMC Test Engineer) Neville Liyanapatabendige (Manager) Date This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. RF Radiation Exposure Evaluation Report EMC Bayswater Test Report: E2211-1609D-3 Issue Date: April, 2023 Product: Portable Reader Model No: T1074 Serial No: 2022-081 FCC ID: 2A9FA-07-0025-915-A Customer Details: Mr Julien Lopez CR Mining 3/271 Treasure Road North Welshpool WA 6106 Australia Phone No: +61 (08) 6253 3913 e-mail: [email protected] Standard(s): CFR47 FCC Part 2, Subpart J, 2.1093 Radiofrequency radiation exposure evaluation: portable devices. FCC KDB 447498 D01 v06 RF EXPOSURE PROCEDURES AND EQUIPMENT AUTHORIZATION POLICIES FOR MOBILE AND PORTABLE DEVICES Results Summary: RF Radiation exposure requirements Complied Test Date(s): 3 rd of February, 2023 Test House (Issued By): EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South Victoria, 3136 Australia FCC Accredited Test Firm Registration number: 527798 FCC Accredited Test Firm Designation number: AU0004 Phone No: +61 3 9761 5888 Email: [email protected] Fax: +61 3 8761 6547 Web: www.emcbayswater.com.au The CR Mining, T1074, Portable Reader, measured EIRP is below the SAR exception threshold (50mm distance) and the calculated power density level at a distance of 20cm are below the maximum levels allowed by regulations therefore complied with the requirements of CFR47 FCC Part 2, Subpart J, 2.1093. This is to certify that the necessary evaluations were made by EMC Bayswater Pty Ltd, and that the CR Mining, T1074, Portable Reader, has been tested in accordance with requirements contained in the appropriate commission regulations. EMC Bayswater Test Report E2211-1609D-3 Page 3 of 7 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. RF Radiation Exposure Evaluation for CR Mining Contents 1. Introduction ................................................................................................................... 4 2. Test Report Revision History ........................................................................................ 4 3. Report Information ........................................................................................................ 4 4. Product Details .............................................................................................................. 5 4.1. Product Sample Details ........................................................................................... 5 4.2. Product description .................................................................................................. 5 5. SAR and RF Exposure exception evaluation ............................................................... 6 5.1. SAR exception evaluation ........................................................................................ 6 5.2. RF Exposure Evaluation (MPE) ............................................................................... 7 6. Conclusion ..................................................................................................................... 7 EMC Bayswater Test Report E2211-1609D-3 Page 4 of 7 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. 1. Introduction RF Radiation Exposure evaluation was performed on a CR Mining, T1074, Portable Reader in accordance with CFR47 FCC Part 2, Subpart J, 2.1093. 2. Test Report Revision History None 3. Report Information EMC Bayswater Pty Ltd reports apply only to the specific samples tested under the stated test conditions. All samples tested were in good operating condition throughout the entire test program unless otherwise stated. EMC Bayswater Pty Ltd does not in any way guarantees the later performance of the product/equipment. It is the manufacturer's responsibility to ensure that additional production units of the tested model are manufactured with identical electrical and mechanical components. EMC Bayswater Pty Ltd shall have no liability for any deductions, inference or generalisations drawn by the clients or others from EMC Bayswater Pty Ltd issued reports. This report shall not be used to claim, constitute or imply product endorsement by EMC Bayswater Pty Ltd. This report shall not be reproduced except in full, without the written approval of EMC Bayswater Pty Ltd. This document may be altered or revised by EMC Bayswater Pty Ltd personnel only, and shall be noted in the revision section of the document. Any alteration of this document not carried out by EMC Bayswater Pty Ltd will nullify the document. EMC Bayswater Test Report E2211-1609D-3 Page 5 of 7 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. 4. Product Details 4.1. Product Sample Details The device, as supplied by the client, is described as follows: Product: Portable Reader Model No: T1074 Serial No: 2022-081 Firmware: 5.0.3.9 Software: 4.1.1.7 Power Specifications: Rechargeable battery 1x 3.6V lithium NCR18650PF Dimensions: 104 x 105 x 275 (mm) (Length x Width x Height) Weight: 750g EUT Type: Tested as table top. Transmitter Details: Description: Portable Reader Type: User interface Modulation: GSFK Channels: 903 to 927Mhz Max power: 10mW Antenna: 4 SMD antennas FCC ID: 2A9FA-07-0025-915-A (Customer supplied product information) 4.2. Product description The dev…

Text truncated - open the document above for the full version.

Page 1 of 98 EMC Bayswater Pty Ltd EMC ENGINEERS & LABORATORIES 18/88 Merrindale Drive Croydon South, Victoria, 3136, Australia Telephone: +61 3 9761 5888 Facsimile: +61 3 8761 6547 Email: [email protected] ABN: 49 112 221 333 RADIO COMPLIANCE REPORT Certification Test Report In accordance with: CFR47 FCC Part 15, Subpart C, 15.247 CR Mining T1074 Portable Reader FCC ID: 2A9FA-07-0025-915-A REPORT: E2211-1609D-2 DATE: April, 2023 Accreditation Number: 18553 Accredited for compliance with ISO/IEC 17025 - Testing The results of the tests, calibrations and/or measurements included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing and calibration reports. This document may not be reproduced except in full without approval from EMC Bayswater, with the exception of the certificate on page 2. EMC Bayswater Test Report E2211-1609D-2 Page 2 of 98 Prepared & tested by: Approved by: 21/04/2023 10:46 Adnan Zaman (EMC Test Engineer) Neville Liyanapatabendige (Manager) Date Accreditation number: 18553. The results of the tests, calibrations and/or measurements included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document may not be reproduced except in full without approval from EMC Bayswater, with the exception of the certificate on page 2. Certificate of Compliance Certification Compliance Report EMC Bayswater Test Report: E2211-1609D-2 Issue Date: April, 2023 Test Sample(s): Portable Reader Model No: T1074 Serial No: 2022-081 FCC ID: 2A9FA-07-0025-915-A Customer Details: Mr Julien Lopez CR Mining 3/271 Treasure Road North Welshpool WA 6106 Australia Phone No: +61 (08) 6253 3913 e-mail: [email protected] Test Specification: CFR47 FCC Part 15, Subpart C, 15.247 Results Summary: 15.203 - Antenna requirement Complied 15.247 (a)(2) - 6dB Bandwidth Complied 15.247 (b)(3) - Maximum Output Power Complied 15.247 (d) - Out-of-Band Emissions - – 100kHz, -20dBc Complied 15.247 (d) - Emissions on the Band edge Complied 15.247 (d), 15.209 - Radiated emissions in Restricted bands Complied 15.247 (e) - Power Spectral Density Complied 15.247 (i) - Radio frequency hazard Complied 15.109 - Radiated Emissions (Receive Mode) Complied 15.111 - Antenna power conduction limits for receivers Complied Test Date(s): 19 th of December, 2022 to 3 rd of February, 2023 Test House (Issued By): EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South Victoria 3136 Australia FCC Accredited Test Firm …

Text truncated - open the document above for the full version.