2AA2U-DTU110Wireless Portable Hard Drive

TOSHIBA Canvio Aero Cast ™ User’s Manual English 2 For the state of California only. Safety information and Rules and Regulations for wireless LAN Wireless LAN devices may cause interference with medical equipment such as cardiac pacemakers. If you use personal medical equipment, consult with your physician and medical equipment instructions before using the Product. The Product should not be used in environments with medical equipment such as hospitals and medical offices, or near users of personal medical equipment, as use of this Product may cause injury in such environments. Always turn off wireless functionality if the computer is near automatic control equipment or appliances such as automatic doors or fire detectors. Radio waves can cause malfunction of such equipment, possibly resulting in injury. Do not use the Wireless LAN functionality near a microwave oven or in areas subject to radio interference or magnetic fields. Interference from a microwave oven or other source can disrupt Wireless LAN operation. The transmission speed over the wireless LAN, and the distance over which the wireless LAN can reach, may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, client design and software/hardware configurations. The transmission rate described is the theoretical maximum speed as specified under the appropriate standard – the actual transmission speed will be lower than the theoretical maximum speed. 3 Federal Communications Commission (FCC) Notice (USA) Complies with FCC RF Exposure requirements. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ❖ Reorient or relocate the receiving antenna. ❖ Increase the separation between the equipment and the receiver. ❖ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ❖ Consult the dealer or an experienced radio or television technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radiation Exposure Statement: This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. 4 Declaration of Conformity for Products Marked with the FCC Logo (USA) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. Canadian Notice This device complies with the Canadian ICES-003 Class B specifications and RSS-210 of Industry Canada. Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Wireless operation is subject to 2 conditions. The first is that the wireless device may not cause interference. The second is that the wireless device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numérique de classe B satisfait à toutes les exigences des Normes sur le matériel brouilleur au Canada. Le fonctionnement sans fil est assujetti à 2 conditions. La première est que l'appareil sans fil ne doit pas causer d'interférence. La seconde est que l'appareil sans fil doit accepter toute interférence, y compris celle susceptible de causecauser un fonctionnement indésirable de l'appareil. To comply with the Canadian RF exposure compliance requirements, this device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. Pour être conforme aux exigences canadiennes en matière d'exposition aux fréquences radio, l'appareil et son antenne ne doivent pas être situés au même endroit qu'une autre antenne ou un autre émetteur ni fonctionner en même temps. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si …

Text truncated - open the document above for the full version.

Page 1 of 3 Report No.: 140701C04 CONSTRUCTION PHOTOS OF EUT Page 2 of 3 Report No.: 140701C04 Page 3 of 3 Report No.: 140701C04

FCC ID : 2AA2U-DTU110IC : 1365F-DTU110CAN ICES-3 (B)/NMB-3(B) BC FCC ID : 2AA2U-DTU110IC : 1365F-DTU110CAN ICES-3 (B)/NMB-3(B) BC FCC ID : 2AA2U-DTU110IC : 1365F-DTU110CAN ICES-3 (B)/NMB-3(B) BC Made in Philippines This device complies with Pat 15 of the FCC Rules.Operation is subject to the following two conditions:(1)This device may not cause harmful interference,and (2) this device must accept any interference received,including interference that may cause undesired operation. Pull-in way from vendor Example Label 3 MM 3 MM 2 MM Example Label 2 MM Made in Philippines This device complies with Pat 15 of the FCC Rules.Operation is subject to the following two conditions:(1)This device may not cause harmful interference,and (2) this device must accept any interference received,including interference that may cause undesired operation. FCC ID : 2AA2U-DTU110IC : 1365F-DTU110CAN ICES-3 (B)/NMB-3(B) BC 00 HSF (Hazardous Substances Free) COMPLIANCE 20147/02 Dora WH3A8(WIFI HDD) PRODUCT LABEL(TAIS) HGWH3A84B02 Joline 20147/02 +/- 0.2 SPEC: 47.8X30MM R1.1X4, 0.08T,1C-Black, Plastic Fasson_50micron WhitePET TC/S333/BG50#WHOvprlamimapion_25micron Glossy Glear PolyesterRIBBON:White for UL certification UL certification: 1) supplier, 2) product number, 3) UL certification number Ink (ribbon) 底材 : 白色 PET / / 覆膜 : 透明 PET / 白色碳帶 6 O’CLOCK FACE OUT 1:1 Die Cut 47.8MM 30 MM R 1.1 47.8MM 30 MM R 1.1 1:1 Artwork 1:1 Label printing area Made in Philippines This device complies with Pat 15 of the FCC Rules.Operation is subject to the following two conditions:(1)This device may not cause harmful interference,and (2) this device must accept any interference received,including interference that may cause undesired operation. FAC: F A www.toshibastorage.com DC+5V 2.0A xxxxB MM/YY MAC : XX:XX:XX:XX:XX:XX S/N: XXXXXXXXXXXX P/N: HDTU110XKWC1 Model : DTU110 Space of1.5~2.5mm 47MM 18MM 5.3MM Made in Philippines This device complies with Pat 15 of the FCC Rules.Operation is subject to the following two conditions:(1)This device may not cause harmful interference,and (2) this device must accept any interference received,including interference that may cause undesired operation. 47MM 18MM 5.3MM 47.8mm 8.15 mm 5.62 mm 5 mm 12 mm 5 mm 5.88 mm Label printing area

Page 1 of 7 Report No.: 140701C04 CONSTRUCTION PHOTOS OF EUT Page 2 of 7 Report No.: 140701C04 Page 3 of 7 Report No.: 140701C04 Page 4 of 7 Report No.: 140701C04 Page 5 of 7 Report No.: 140701C04 Page 6 of 7 Report No.: 140701C04 Page 7 of 7 Report No.: 140701C04

FCC SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 22 Report No. : SA140701C04 Issued Date : Jul. 16, 2014 FCC SAR Test Report Report No. : SA140701C04 Applicant : Cal-Comp Electrocins and communications Co.,Ltd. Address : No.147, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 22201, Taiwan (R.O.C.) Product : Wireless Portable Hard Drive FCC ID : 2AA2U-DTU110 Brand : TOSHIBA Model No. : DTU110; DTU1xx Standards : FCC 47 CFR Part 2 (2.1093) / IEEE C95.1:1992 / IEEE 1528:2003 IEEE 1528a-2005 / KDB 865664 D01 v01r03 KDB 248227 D01 v01r02 / KDB 447498 D01 v05r02 Sample Received Date : Jul. 01, 2014 Date of Testing : Jul. 11, 2014 CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch – Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Vera Huang / Specialist Approved By : Roy Wu / Manager This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. FCC SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 22 Report No. : SA140701C04 Issued Date : Jul. 16, 2014 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement System ................................................................................................................................................... 6 3.1 Definition of Specific Absorption Rate (SAR) ............................................................................................................... 6 3.2 SPEAG DASY System ................................................................................................................................................. 6 3.2.1 Robot .................................................................................................................................................................. 7 3.2.2 Probes ................................................................................................................................................................ 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................... 8 3.2.4 Phantoms ........................................................................................................................................................... 9 3.2.5 Device Holder ................................................................................................................................................... 10 3.2.6 System Validation Dipoles ................................................................................................................................ 10 3.2.7 Tissue Simulating Liquids ................................................................................................................................. 11 3.3 SAR System Verification ............................................................................................................................................ 14 3.4 SAR Measurement Procedure ................................................................................................................................... 15 3.4.1 Area & Zoom Scan Procedure ......................................................................................................................... 15 3.4.2 Volume Scan Procedure ................................................................................................................................... 15 3.4.3 Power Drift Monitoring ...................................................................................................................................... 16 3.4.4 Spatial Peak SAR Evaluation ........................................................................................................................... 16 3.4.5 SA…

Text truncated - open the document above for the full version.

Report No.: RF140701C04 1 of 51 Report Format Version 5.2.1 FCC TEST REPORT (15.247) REPORT NO.: RF140701C04 MODEL NO.: DTU110; DTU1xx FCC ID: 2AA2U-DTU110 RECEIVED: Jul. 01, 2014 TESTED: Jul. 03, 2014 ~ Jul. 11, 2014 ISSUED: Jul. 16, 2014 APPLICANT: Cal-Comp Electrocins and communications Co.,Ltd. ADDRESS: No.147, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 22201, Taiwan (R.O.C.) ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF140701C04 2 of 51 Report Format Version 5.2.1 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................................. 4 1. CERTIFICATION ................................................................................................................................. 5 2. SUMMARY OF TEST RESULTS ........................................................................................................ 6 2.1 MEASUREMENT UNCERTAINTY ............................................................................................. 6 3. GENERAL INFORMATION ................................................................................................................. 7 3.1 GENERAL DESCRIPTION OF EUT ........................................................................................... 7 3.2 DESCRIPTION OF TEST MODES ............................................................................................. 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................................ 9 3.3 DESCRIPTION OF SUPPORT UNITS ...................................................................................... 11 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................................... 11 3.4 DUTY CYCLE TEST SIGNAL ................................................................................................... 12 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................................... 13 4. TEST TYPES AND RESULTS (FOR 2.4GHz BAND) ....................................................................... 14 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................. 14 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................... 14 4.1.2 TEST INSTRUMENTS ................................................................................................. 15 4.1.3 TEST PROCEDURES ................................................................................................. 16 4.1.4 DEVIATION FROM TEST STANDARD ....................................................................... 16 4.1.5 TEST SETUP ............................................................................................................... 17 4.1.6 EUT OPERATING CONDITIONS ................................................................................ 18 4.1.7 TEST RESULTS........................................................................................................... 18 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................................... 31 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................... 31 4.2.2 TEST INSTRUMENTS ................................................................................................. 31 4.2.3 TEST PROCEDURES ................................................................................................. 32 4.2.4 DEVIATION FROM TEST STANDARD ....................................................................... 32 4.2.5 TEST SETUP ............................................................................................................... 33 4.2.6 EUT OPERATING CONDITIONS ................................................................................ 33 4.2.7 TEST RESULTS........................................................................................................... 34 4.3 6dB BANDWIDTH MEASUREMENT ....................................................................................... 36 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ........................................................ 36 4.3.2 TEST SETUP ............................................................................................................... 36 4.3.3 TEST INSTRUMENTS ...…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST

FCC SAR Test Report Report Format Version 5.0.0 Issued Date : Jul. 16, 2014 Report No. : SA140701C04 Appendix D. Photographs of EUT and Setup FCC SAR Test Report Report Format Version 5.0.0 Report No. : SA140701C04 <Photographs of EUT> <Antenna Location> The separation distance for antenna to edge: Antenna To Top Side (mm) To Bottom Side (mm) To Left Side (mm) To Right Side (mm) WLAN 5.37 114.41 14.83 67.97 EUT Top Side EUT Bottom Side EUT Right Side EUT Left Side WLAN Antenna <EUT Front View> FCC SAR Test Report Report Format Version 5.0.0 Report No. : SA140701C04 <Photographs of SAR Setup> Front Face of EUT with 0 cm Gap Rear Face of EUT with 0 cm Gap Left Side of EUT with 0 cm Gap Top Side of EUT with 0 cm Gap