2AABGBTAC1000Bluetooth module

Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: 2AABGBTAC1000”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

EnzyTek Technology, Inc. 7F, No. 35, Hsueh Fu Rd., Hsinchu 300, Taiwan , R.O.C. TEL：886-3-573-6708 FAX： 886-3-573-8749 1 EnzyTek EnzyTek Technology, Inc . BTA-C1000-2 Preliminary Datasheet Issued date: May 22, 2013 EnzyTek Technology, Inc. 7F, No. 35, Hsueh Fu Rd., Hsinchu 300, Taiwan , R.O.C. TEL：886-3-573-6708 FAX： 886-3-573-8749 2 EnzyTek EnzyTek Technology, Inc . EnzyTek Bluetooth ® Low Energy Module With on Board Antenna BTA-C1000-2 OVERVIEW Highly integration BT 4.0 Low Energy Class II module, CSR CS1000 + Memory + Filter + X’Tal + Chip Antenna. Wireless communications module conforming to Bluetooth Version 4.0. UART, SPI interfaces available to various applications. 5 GPIO ports available for user’s application. 3 Analog IO ports available for user’s application. BT Chipset : CSR CSR1000 Standards : Bluetooth 4.0 Low Energy. Frequency : 2402 ~ 2480 MHz TX Output Power : 4 dBm (max) RX Sensitivity : -88 dBm (min) Range : > 10 m (line-of-sight at open space) Memory : EEPROM (512K bits) Operation Voltage : 1.8V ~ 3.6V Dimension : 18 x 13 x 2.2 (max) mm 3 (L×W×H) Environmental Range : Operation Temperature : 0~+70 o C, Relative humidity : 0~95% EnzyTek Technology, Inc. 7F, No. 35, Hsueh Fu Rd., Hsinchu 300, Taiwan , R.O.C. TEL：886-3-573-6708 FAX： 886-3-573-8749 3 EnzyTek EnzyTek Technology, Inc . System Block Diagram CSR CSR1000 EEPROM Filter 16MHz XTAL UART (PIO[1:0]) SPI PIO[4:3] PIO[11:9] 32KHz XTAL AIO[2:0] WAKE EnzyTek Technology, Inc. 7F, No. 35, Hsueh Fu Rd., Hsinchu 300, Taiwan , R.O.C. TEL：886-3-573-6708 FAX： 886-3-573-8749 4 EnzyTek EnzyTek Technology, Inc . Pinout Diagram / Dimension Unit : mm Note: Please contact EnzyTek to get the detail footprint of the module to do the PCB design. H3 HOLE_1mm 1 VDD_IO SPI_CSB 0.3mm Bottom J15SPI_CSB IO PIO_9 2.5 mm J6PIO[1]/UART_RX IO 18 mm TP1 0.8MM_PAD 1 2 0.8mm J2AIO[2] IO H5 HOLE_0.4X1.8mm 1 0.4mm0.57mm SPI_MISO J17WAKE IO Top J18VDD_IN IO J9VDD_IO IO VDD_IN PIO_3 SPI_CLK J14SPI_MOSI IO 10.4 mm J7PIO[3] IO SPI_MOSI H6 HOLE_0.4X1.8mm 1 Antenna Keepout Area H1 HOLE_1mm 1 0.57mm J8PIO[4] IO PIO_10 0.4mm J12PIO[11] IO H4 HOLE_0.4X1.8mm 1 UART_RX AIO_0 J13SPI_MISO IO J5PIO[0]/UART_TX IO PIO_11 7.5 mm 3.9 mm 13 mm J4AIO[0] IO AIO_1 J3AIO[1] IO 3.65 mm J10PIO[10] IO 3.65 mm PIO_4 PCB thickness : 0.8mm H2 HOLE_1mm 1 J11PIO[9] IO J16SPI_CLK IO WAKE 1 mm UART_TX PAD Size J1GND IO AIO_2 EnzyTek Technology, Inc. 7F, No. 35, Hsueh Fu Rd., Hsinchu 300, Taiwan , R.O.C. TEL：886-3-573-6708 FAX： 886-3-573-8749 5 EnzyTek EnzyTek Technology, Inc . I/O PIN LISTING Pin No. Pin Name Type Description J1 GND Power Ground J2 AIO_2 Analog bi-directional Programmable input/output line J3 AIO_1 Analog bi-directional Programmable input/output line J4 AIO_0 Analog bi-directional Programmable input/output line J5 UART_TX (PIO_0) CMOS output, tri-state, with weak internal pull-up UART data output t, optional PIO0 which is defined by FW. J6 UART_RX (PIO_1) CMOS input with weak internal pull-down UART data input, optional PIO1 which is defined by FW. J7 PIO_3 Bi-directional with programmable strength internal pull-up/down Programmable input/output line J8 PIO_4 Bi-directional with programmable strength internal pull-up/down Programmable input/output line J9 VDD_IO Power IO VDD, NC. J10 PIO_10 Bi-directional with programmable strength internal pull-up/down Programmable input/output line J11 PIO_9 Bi-directional with programmable strength internal pull-up/down Programmable input/output line J12 PIO_11 Bi-directional with programmable strength internal pull-up/down Programmable input/output line J13 SPI_MISO CMOS output, tri-state, with weak internal pull-down Serial Peripheral Interface data output J14 SPI_MOSI CMOS input with weak internal pull-down Serial Peripheral Interface data input J15 SPI_CSB CMOS input with weak internal pull-up Chip select for Synchronous Serial Interface active low J16 SPI_CLK CMOS input with weak internal pull-down Serial Peripheral Interface clock J17 WAKE Input has no internal pull-up or pull-down, use external pull-down. Input to wake the module from hibernate or dormant. J18 VDD_IN Power 3.3V input EnzyTek Technology, Inc. 7F, No. 35, Hsueh Fu Rd., Hsinchu 300, Taiwan , R.O.C. TEL：886-3-573-6708 FAX： 886-3-573-8749 6 EnzyTek EnzyTek Technology, Inc . Electrical Characteristics Absolute Maximum Ratings : Min. Typ. Max. Unit Supply Voltage - - 3.6 V Storage Temperature -40 - 85 o C Recommend Operation Conditions : Min. Typ. Max. Unit Supply Voltage 1.8 - 3.6 V Storage Temperature 0 - 70 o C Input/Output Terminal Characteristics : Min. Typ. Max. Unit Digital (UART, PIO) V IL Input Voltage Low -0.4 - +0.4 V V IH Input Voltage High 0.7xVDD - VDD+0.4 V V OL Output Voltage Low, (I O is 4mA) - - 0.4 V V OH Output Voltage High, (I O is -4mA) 0.75xVDD - - V EnzyTek Technology, Inc. 7F, No. 35, Hsueh Fu Rd., Hsinchu 300, Taiwan , R.O.C. TEL：886-3-573-6708 FAX： 886-3-573-8749 7 EnzyTek EnzyTek Technology, Inc . Radio Characteristics VCC = 3.3V Min Typ Max Limits(BLE SPEC)Unit Output Power Max Power 4 <10 dBm Min Power -20 >-20 dBm Peak to Average 0 <3 dBm Carrier drift Fn -150 150 <=150 kHz Drift rate -20 20 <20 kHz/50us Max Power -50 50 <50 kHz Modulation Characteristic F1avg','F1max' 225 275 225<= <=275 kHz F2avg','F2max' 185 >=185 kHz F1/F2 Ratio 0.8 >=0.8 Sensitivity (-88dBm) Frame Error Rate 0 30.8 <=30.8(-70dBm) % PER Integrity Frame Error Rate 50 65.4 50<= <=65.4 % Max Input Power Frame Error Rate 0 <=30.8(-40dBm) % EnzyTek Technology, Inc. 7F, No. 35, Hsueh Fu Rd., Hsinchu 300, Taiwan , R.O.C. TEL：886-3-573-6708 FAX： 886-3-573-8749 8 EnzyTek EnzyTek Technology, Inc . Current Consumption HW BTM‐C1000‐2 FW version F‐Serial_Port‐v003 FW configuration Role Gatt Server, device side Service SPS Service Baud Rate 2400 Default PowerScale 0 BT BLE Host iPhone 4S (ios5) Current Meter Fluke 189 Min. Avg. Max. Power On No connection 5.93 uA 6.79 uA 39.90uA Power On advertising 202 uA 365 uA 567 uA Connected No Data Transfer 15 uA 69 uA 143 uA Connected…

Text truncated - open the document above for the full version.

FCC ID: 2AABGBTAC1000 Report No.: RF130418C16 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch May 24, 2013 Dear Application Examiner, EnzyTek Technology, Inc., FCC ID: 2AABGBTAC1000 would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of Public Notice DA00-1407 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip CSR1000. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is CSR1000. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a convertible board. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: 2AABGBTAC1000 Report No.: RF130418C16 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Robert Huang Senior Engineer Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch

Page 1 CONSTRUCTION PHOTOS OF EUT

FCC Label Location FCC ID:2AABGBTAC1000 Logo by laser marking

Page 2 Page 3

Report No.: SA130418C16A 1 of 6 Report Format Version 5.0.0 Ref. no.: 130516C02 RF EXPOSURE REPORT REPORT NO.: SA130418C16A MODEL NO.: BTA-C1000-2_V02 FCC ID: 2AABGBTAC1000 RECEIVED: Apr. 18, 2013 TESTED: May 03 ~ May 07, 2013 ISSUED: May 20, 2013 APPLICANT: EnzyTek Technology, Inc. ADDRESS: 7F, No.35, Hsueh Fu Rd., Hsinchu 300, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: SA130418C16A 2 of 6 Report Format Version 5.0.0 Ref. no.: 130516C02 Table of Contents RELEASE CONTROL RECORD .............................................................................................................. 3 1. CERTIFICATION ....................................................................................................................... 4 2. RF EXPOSURE ........................................................................................................................ 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) .................................................. 5 2.2 MPE CALCULATION FORMULA .............................................................................................. 5 2.3 CLASSIFICATION ..................................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ........................................... 6 Report No.: SA130418C16A 3 of 6 Report Format Version 5.0.0 Ref. no.: 130516C02 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA130418C16A Original release May 20, 2013 Report No.: SA130418C16A 4 of 6 Report Format Version 5.0.0 Ref. no.: 130516C02 1. CERTIFICATION PRODUCT:Bluetooth module MODEL NO.:BTA-C1000-2_V02 BRAND: NA APPLICANT:EnzyTek Technology, Inc. TESTED:May 03 ~ May 07, 2013 TEST SAMPLE:ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: BTA-C1000-2_V02) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :May 20, 2013 Ivy Lin / Specialist APPROVED BY : , DATE :May 20, 2013 Ken Liu / Senior Manager Report No.: SA130418C16A 5 of 6 Report Format Version 5.0.0 Ref. no.: 130516C02 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA130418C16A 6 of 6 Report Format Version 5.0.0 Ref. no.: 130516C02 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2402 ~ 2480 4.50 2.5 20 0.001 1 --- END ---

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 3 RADIATED EMISSION TEST