2AACXXCVR2Modular Tansceiver

Green Edge Technologies, Inc. Confidential shared under NDA Page 1 of 2 User Manual 21 October 2014 Antenna Selection The antenna for Gen2 devices is a copper trace antenna integrated within the Transceiver PCB. The antenna has been tuned to operate most effectively at 915MHz. The module’s antenna is integrated into the PCB of the module, thus it require no external antenna. It is recommended that the module is placed such that it antenna is more that 10mm from any metal as to not degrade the performance of the antenna. Labeling Instructions Per FCC and IC requirements, any host device that contains this transceiver module must have the module’s FCC & IC ID clearly labeled on the host device’s exterior. The label must include the module’s FCC & IC ID and must indicate that it “contains” the module. For example: "Contains Transmitter Module FCC ID: 2AACXXCVR2 - IC: 11483A-XCVR2" or "Contains FCC ID: 2AACXXCVR2" "Contains IC: 11483A-XCVR2" FCC Statements Changes or modification not expressly approved by Green Edge Technologies, Inc. (Green Edge) could void the user’s authority to operate the device. Green Edge Technologies, Inc. Confidential shared under NDA Page 2 of 2 The following FCC statements apply to this module. Additionally, the statements must be included in the host device’s user manual. Important Note: Changes or modification not expressly approved by Green Edge Technologies, Inc. (Green Edge) could void the user’s authority to operate the device. The Federal Communication Commission Radio Interference Statement includes the following paragraph: This equipment has been tested and found to comply with the limits for a class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device uses, generates and can radiate radio frequency energy, and if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with respect to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by the following measures: 1) Separate the devices from this equipment. 2) Reorient the device with respect to this equipment. 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio technician for help. Operation is subject to the following two conditions: . 1) This device may not cause interference . 2) This device must accept any interference, including interference that may cause undesired operation of the device This information must appear in the user manual. It can be provided as a paper manual or in electronic form provided the user can be reasonably expected to have the capability to access the manual in that form.

15333 Avenue of Science, Suite 110, San Diego, CA 92128 / T: 858.799.0360 www.edgehome.com October 21, 2014 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2AACXXCVR2 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Antenna Specification Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-­‐1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-­‐term confidentiality request for 180 days on the following attachments: Internal Photos External Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, William Rice SVP of Engineering Green Edge Technologies, Inc.

15333 Avenue of Science, Suite 110, San Diego, CA 92128 / T: 858.799.0360 www.edgehome.com October 16, 2014 UL LLC Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Bart Mucha, an employee of UL LLC, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL LLC on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-­‐Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL LLC as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; 15333 Avenue of Science, Suite 110, San Diego, CA 92128 / T: 858.799.0360 www.edgehome.com i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, William Rice SVP of Engineering Green Edge Technologies, Inc.

Green Edge Technologies FCC ID:2AACXXCVR2 Request for transmitter modular approval Transmitter Module Characteristics Item Requirements EUT 1 Have its own RF shielding Device is equipped with Metal shielding to cover RF section. Refer to device photos 2 Have buffered modulation/data inputs (if such inputs are provided), All inputs to the modules are buffered through logic or microprocessor inputs. 3 Have it own power supply regulation It has on onboard 3.3V power regulator. Refer to Block diagram 4 Meet the antenna requirements of Section 15.203 Device is equipped PCB trace antenna. No external antenna can be used with this device. 5 Be tested in a stand-alone configuration, i.e., the antenna, AC or DC power and data input/output lines must be connected to the module but, the module must not be inside another case during testing Device was tested using a power adapter. It was not inside any other case during testing. Refer to setup photos. 6 Be labeled with its own FCC ID number, and if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. Two proposed FCC ID label format are included in the filing. One of label is to be placed on the module and the other label is to be placed on the outside of system. Refer to FCC ID label format and location file. 7 The modular transmitter is manufactured so that the user cannot influence the operation of the transmitter that will operate outside of the scope of the regulations. Refer to “User’s Guide” Exhibit 8 Address compliance with the Commission's RF exposure limits in Sections 1.1310 and 2.1093. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF exposure compliance in accordance with Section 15.247(b)(4). The devices complies with Section 1.1310 and 2.1093 since the device’s transmit power is significatly below the required limits. Additionally, it is not a “portable device” nor is designed to be used within 20cm of the body of the user. The device complies with Secion 15.247(b)(4) since the directional gain of the device’s antenna is less than 6dbi.

FCC ID Label: Module Label Label Location: •The FCC ID will be place on a small label on the module •Alternately, the FCC ID will be silkscreened directly on the PCB of the Module 20-00001-01 Rev B FCC ID: 2AACXXCVR2 IC:11483A-XCVR2 Label Format: FCC ID Label: External Label •FCC ID will visible on the external label the device hosting the module Example External Label Format: Contains FCC ID: 2AACXXCVR2 Contains IC: 11483A-XCVR2

NVLAP Lab code: 100414-0 FCC 47 CFR PART 15 SUBPART C INDUSTRY CANADA RSS-210 ISSUE 8 CERTIFICATION TEST REPORT FOR Modular Transceiver MODEL NUMBER: 20-00001-01 FCC ID: 2AACXXCVR2 IC: 11483A-XCVR2 REPORT NUMBER: 10165600A ISSUE DATE: October 6, 2014 Prepared for Green Edge Technologies 15333 Avenue of Science San Diego, CA 92128 USA Prepared by UL LLC 333 Pfingsten Rd. Northbrook, IL 60062 TEL: (847) 272-8800 REPORT NO: 10165600A DATE: October 6, 2014 FCC ID: 2AACXXCVR2 IC: 11483A-XCVR2 Page 2 of 51 UL LLC FORM NO: CCSUP4701i 333 Pfingsten Rd., Northbrook, IL 60062, USA TEL: (847) 272-8800 This report shall not be reproduced except in full, without the written approval of UL LLC Revision History Rev. Issue Date Revisions Revised By -- October 6, 2014 Initial Issue BM REPORT NO: 10165600A DATE: October 6, 2014 FCC ID: 2AACXXCVR2 IC: 11483A-XCVR2 Page 3 of 51 UL LLC FORM NO: CCSUP4701i 333 Pfingsten Rd., Northbrook, IL 60062, USA TEL: (847) 272-8800 This report shall not be reproduced except in full, without the written approval of UL LLC TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................................................ 4 2. TEST METHODOLOGY ...................................................................................................................................... 5 3. FACILITIES AND ACCREDITATION .............................................................................................................. 5 4. CALIBRATION AND UNCERTAINTY ............................................................................................................. 5 4.1. MEASURING INSTRUMENT CALIBRATION................................................................................................. 5 4.2. SAMPLE CALCULATION ................................................................................................................................ 5 4.3. MEASUREMENT UNCERTAINTY .................................................................................................................. 6 5.6. DESCRIPTION OF TEST SETUP .................................................................................................................... 8 6. TEST AND MEASUREMENT EQUIPMENT .................................................................................................. 10 7. TEST RESULTS ................................................................................................................................................... 11 7.1.1. 99% BANDWIDTH ............................................................................................................................... 11 7.2. RADIATED EMISSIONS ................................................................................................................................ 15 7.2.1. FUNDAMENTAL FREQUENCY RADIATED EMISSION ................................................................ 16 7.2.2. TRANSMITTER BAND EDGES .......................................................................................................... 17 7.2.3. HARMONICS AND SPURIOUS EMISSIONS ABOVE 1GHz ........................................................... 21 7.2.4. WORST-CASE BELOW 1 GHz ............................................................................................................ 39 8. AC MAINS LINE CONDUCTED EMISSIONS ............................................................................................... 41 9. SETUP PHOTOS .................................................................................................................................................. 46 REPORT NO: 10165600A DATE: October 6, 2014 FCC ID: 2AACXXCVR2 IC: 11483A-XCVR2 Page 4 of 51 UL LLC FORM NO: CCSUP4701i 333 Pfingsten Rd., Northbrook, IL 60062, USA TEL: (847) 272-8800 This report shall not be reproduced except in full, without the written approval of UL LLC 1. ATTESTATION OF TEST RESULTS COMPANY NAME: Green Edge Technologies 15333 Avenue of Science San Diego, CA 92128 EUT DESCRIPTION: 902MHz-928MHz Modular Transceiver MODEL: 20-00001-01 SERIAL NUMBER: 010000105F DATE TESTED: September 22, 2014 – September 23, 2014 APPLICABLE STANDARDS STANDARD TEST RESULTS CFR 47 Part 15 Subpart C Pass INDUSTRY CANADA RSS-210 Issue 8 Annex 8 Pass INDUSTRY CANADA RSS-GEN Issue 3 Pass UL LLC tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by UL LLC based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by UL LLC and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL LLC will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, any agency of the Federal Government, or any agency of any government. Approved & Released For UL LLC By: Tested By: Michael Ferrer Bart Mucha EMC Engineer EMC Engineer UL LLC UL LLC REPORT NO: 10165600A DATE: October 6, 2014 FCC ID: 2AACXXCVR2 IC: 11483A-XCVR2 Page 5 of 51 UL LLC FORM NO: CCSUP4701i 333 Pfingsten Rd., Northbrook, IL 60062, USA TEL: (847) 272-8800 This report shall not be reproduced except in full, without the written approval of UL LLC 2. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4-2003, FCC CFR 47 Part 2, FCC CFR 47 Part 15, RSS-GEN Issue 3, and RSS-210 Issu…

Text truncated - open the document above for the full version.

REPORT NO: 10165600A DATE: October 6, 2014 FCC ID: 2AACXXCVR2 IC: 11483A-XCVR2 Page 46 of 51 UL LLC FORM NO: CCSUP4701i 333 Pfingsten Rd., Northbrook, IL 60062, USA TEL: (847) 272-8800 This report shall not be reproduced except in full, without the written approval of UL LLC 9. SETUP PHOTOS Near Field Measurements REPORT NO: 10165600A DATE: October 6, 2014 FCC ID: 2AACXXCVR2 IC: 11483A-XCVR2 Page 47 of 51 UL LLC FORM NO: CCSUP4701i 333 Pfingsten Rd., Northbrook, IL 60062, USA TEL: (847) 272-8800 This report shall not be reproduced except in full, without the written approval of UL LLC RADIATED RF MEASUREMENT SETUP X-Axis REPORT NO: 10165600A DATE: October 6, 2014 FCC ID: 2AACXXCVR2 IC: 11483A-XCVR2 Page 48 of 51 UL LLC FORM NO: CCSUP4701i 333 Pfingsten Rd., Northbrook, IL 60062, USA TEL: (847) 272-8800 This report shall not be reproduced except in full, without the written approval of UL LLC Y-Axis REPORT NO: 10165600A DATE: October 6, 2014 FCC ID: 2AACXXCVR2 IC: 11483A-XCVR2 Page 49 of 51 UL LLC FORM NO: CCSUP4701i 333 Pfingsten Rd., Northbrook, IL 60062, USA TEL: (847) 272-8800 This report shall not be reproduced except in full, without the written approval of UL LLC Z-Axis REPORT NO: 10165600A DATE: October 6, 2014 FCC ID: 2AACXXCVR2 IC: 11483A-XCVR2 Page 50 of 51 UL LLC FORM NO: CCSUP4701i 333 Pfingsten Rd., Northbrook, IL 60062, USA TEL: (847) 272-8800 This report shall not be reproduced except in full, without the written approval of UL LLC Line Conducted Emissions Setup REPORT NO: 10165600A DATE: October 6, 2014 FCC ID: 2AACXXCVR2 IC: 11483A-XCVR2 Page 51 of 51 UL LLC FORM NO: CCSUP4701i 333 Pfingsten Rd., Northbrook, IL 60062, USA TEL: (847) 272-8800 This report shall not be reproduced except in full, without the written approval of UL LLC END OF REPORT