2AAGE-TAB10RK664GTablet

M10 Pro and M10 Lite User Manual M10 PRO AND M10 LITE Hardware User Manual Product Version: 1.0 Date: 2021-1-7 For any question, please contact Chengdu Vantron Technology, Ltd. Copyright © Vantron Technology, Ltd. All rights reserved. Change History This table describes the version and release date. Rev. Date Description Author 1.0 2021-1-7 First release. Shun Zhang Foreword Copyright While all information contained herein have been carefully checked to assure its accuracy in technical details and printing, Vantron assumes no responsibility resulting from any error or features of this manual, or from improper uses of this manual or the software. Please contact our technical department for relevant operation solutions if there is any problem that cannot be solved according to this manual. Vantron reserves all rights of this manual, including the right to change the content, form, product features, and specifications contained herein at any time without prior written notice. The trademarks and registered trademarks in this manual are properties of their respective owners. No part of this manual may be copied, reproduced, translated or sold. No changes or other purposes are permitted without the prior written consent of Vantron. Vantron reserves the right of all publicly-released copies of this manual. Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Type Description Notice Important information and regulations Caution Caution for latent damage to system or harm to personnel Statement & Disclaimer It is recommended to read and comply with this manual which provides important guidance and helps decreasing the danger of injury, electric shock, fire, or any damage to the device. Vantron assumes no legal liability of accidents resulting from failure of conforming to the safety instructions. Limitation of Liability/Non-warranty For direct or indirect damage to this device or other devices of Vantron caused by failure of conforming to this manual or the safety instructions on device label, Vantron assumes neither warranty nor legal liability even if the device is still under warranty. The device should be installed, debugged and maintained by professionals. The outside antennas are not permitted to be installed or to be changed by non- professionals. To run the device normally, only specified antennas are approved to be assembled together by professionals. Unit shall be used with indoor-use antenna only. No antenna for this unit can be installed outdoor. Safety Instructions  Keep and comply with all operation instructions, warnings, and information.  Pay attention to warnings on this device.  Read the following precautions so as to decrease the danger of injury, electric shock, fire, or any damage to the device.  Operations and service instructions are provided with the equipment.  Unit shall be used with indoor-use antenna only. No antenna for this unit can be installed outdoor.  The maximum operation temperature is 45°C. Precautions  Pay attention to the product labels/safety instructions printed on silk screens.  Do not try repairing this product unless declared in this manual.  Keep away from heat source, such as heater, heat dissipater, or engine casing.  Do not insert other items into the slot (if any) of this device. ◆ Ensure ventilation of the ventilation slot. ◆ System fault may arise if other items are inserted into this device.  Installation: ensure correct installation according to instructions from the manufacturer with recommended installation tools.  Ensure ventilation and smoothness according to relevant ventilation standards. Safety Instructions for Power Cables and Accessories Use Proper power source only. Start only with power source that satisfies voltage label and the voltage necessary according to this manual. Please contact technical support personnel of Vantron for any uncertainty about the requirements of necessary power source. Use tested power source. This product still contains a button lithium battery as a real-time clock after its external power source is removed and therefore should not be short-circuited during transportation or placed under high temperature. Place cables properly: Do not place cables at any place with extrusion danger. Cleaning Instructions  Please power off before cleaning the device.  Do not use spray detergent.  Clean with a damp cloth.  Do not try cleaning exposed electronic components unless with a dust collector.  Support for special fault: Power off and contact technical support personnel of Vantron in case of the following faults: ➢ The device is damaged. ➢ The temperature is excessively high. ➢ Fault is still not solved after operations according to the manual. Contents 1 INTRODUCTION ................................................................................................................................................ 1 1.1 PRODUCT DESCRIPTION ................................................................................................................................................ 1 1.2 CONNECTOR DESCRIPTION .......................................................................................................................................... 1 2 OVERVIEW .......................................................................................................................................................... 3 2.1 INTRODUCTION ............................................................................................................................................................. 3 2.2 FEATURE ........................................................................................................................................................................ 3 2.3 ORDER INFORMATION .................................................................................................................................................. 4 3 HARDWARE INSTRUCTIONS .....…

Text truncated - open the document above for the full version.

Chengdu Vantron Technology Co., Ltd. To: Office of Engineering Techno l o g y Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 United States From: Chengdu Vantron Technology Co., ltd. N o. 5 GaoPeng Road, Hi-Tech Zone, Chengdu, SiChuan Chen g Du China Regarding: Confidentiality Request regarding application for FCC ID: 2AAGE-TAB10RK664G LONG TERM CONFIDENTIALITY P ursuant to 47 CFR Section 0.459 and 0.457 of the commission's ru ' les, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application ref ere need above. Schematic(s) Block Diagrams Operational Descriptions NII Software Security Info T une Up The documents above contain prop「ietary in formation not released to the public. Public disclosure of this information may p「ove ha rmful to the business of the applicant. 二:;:: X}i 、 W 千 Printed Name (on file with the FCC associ a ted with the Grantee Code): Xi Wang Title: VP Company Name: Chengdu Vantron Technology Co., Ltd.

Compliance Certification Services (Kunshan) Inc. Page: 1 of 7 External Photos for KSCR2204000420AT Test Model No.: M10 Pro Compliance Certification Services (Kunshan) Inc. Page: 2 of 7 EUT Constructional Details (EUT Photos) Compliance Certification Services (Kunshan) Inc. Page: 3 of 7 Compliance Certification Services (Kunshan) Inc. Page: 4 of 7 Compliance Certification Services (Kunshan) Inc. Page: 5 of 7 Compliance Certification Services (Kunshan) Inc. Page: 6 of 7 Compliance Certification Services (Kunshan) Inc. Page: 7 of 7

Remark:It’s hard to put FCC statement on the product due to device’s irregular appearance. FCC statement will be placed in the user manual which the device is marketed.

Compliance Certification Services (Kunshan) Inc. Page: 1 of 12 Internal Photos for KSCR2204000420AT Test Model No.: M10 Pro Compliance Certification Services (Kunshan) Inc. Page: 2 of 12 EUT Constructional Details (EUT Photos) Compliance Certification Services (Kunshan) Inc. Page: 3 of 12 Compliance Certification Services (Kunshan) Inc. Page: 4 of 12 Compliance Certification Services (Kunshan) Inc. Page: 5 of 12 Compliance Certification Services (Kunshan) Inc. Page: 6 of 12 Compliance Certification Services (Kunshan) Inc. Page: 7 of 12 Compliance Certification Services (Kunshan) Inc. Page: 8 of 12 Compliance Certification Services (Kunshan) Inc. Page: 9 of 12 Compliance Certification Services (Kunshan) Inc. Page: 10 of 12 Compliance Certification Services (Kunshan) Inc. Page: 11 of 12 Compliance Certification Services (Kunshan) Inc. Page: 12 of 12

Compliance Certification Services (Kunshan) Inc. Page: 1 of 28 Appendix C for KSCR220400042006 Calibration Certificate Object Apply No Model SN Calibration Date Dipole 1 CLA150 4025 2021/04/26 2 D450V3 1103 2021/04/21 3 D750V3 1188 2022/03/29 4 D835V2 4d114 2022/03/31 5 D900V2 1d079 2022/06/07 6 D1800V2 2d170 2022/03/31 7 D1900V2 5d136 2022/06/07 8 D2000V2 1041 2022/06/06 9 D2300V2 1096 2022/03/31 10 D2450V2 817 2022/04/01 11 D2600V2 1158 2022/03/31 12 D5GHzV2 1095 2022/06/01 DAE 13 DAE4 1245 2022/05/30 Probe 14 EX3DV4 7346 2022/03/30 Compliance Certification Services (Kunshan) Inc. Page: 2 of 28 1 Dip ole 1.1 CLA150 - SN 4025 Compliance Certification Services (Kunshan) Inc. Page: 3 of 28 1.2 D450V3 - SN 1103 Compliance Certification Services (Kunshan) Inc. Page: 4 of 28 Compliance Certification Services (Kunshan) Inc. Page: 5 of 28 1.3 D750V3 - SN 1188 Compliance Certification Services (Kunshan) Inc. Page: 6 of 28 1.4 D835V2 - SN 4d114 Compliance Certification Services (Kunshan) Inc. Page: 7 of 28 Compliance Certification Services (Kunshan) Inc. Page: 8 of 28 1.5 D900V2 - SN 1d079 Compliance Certification Services (Kunshan) Inc. Page: 9 of 28 1.6 D1800V2 - SN 2d170 Compliance Certification Services (Kunshan) Inc. Page: 10 of 28 Compliance Certification Services (Kunshan) Inc. Page: 11 of 28 1.7 D1900V2 - SN 5d136 Compliance Certification Services (Kunshan) Inc. Page: 12 of 28 1.8 D2000V2 - SN 1041 Compliance Certification Services (Kunshan) Inc. Page: 13 of 28 Compliance Certification Services (Kunshan) Inc. Page: 14 of 28 1.9 D2300V2 - SN 1096 Compliance Certification Services (Kunshan) Inc. Page: 15 of 28 1.10 D2450V2 - SN 817 Compliance Certification Services (Kunshan) Inc. Page: 16 of 28 Compliance Certification Services (Kunshan) Inc. Page: 17 of 28 1.11 D2600V2 - SN 1158 Compliance Certification Services (Kunshan) Inc. Page: 18 of 28 1.12 D5GHzV2 - SN 1095 Compliance Certification Services (Kunshan) Inc. Page: 19 of 28 Compliance Certification Services (Kunshan) Inc. Page: 20 of 28 Compliance Certification Services (Kunshan) Inc. Page: 21 of 28 2 DAE4 - SN 1245 Compliance Certification Services (Kunshan) Inc. Page: 22 of 28 3 EX3DV4 - SN 7346 Compliance Certification Services (Kunshan) Inc. Page: 23 of 28 Compliance Certification Services (Kunshan) Inc. Page: 24 of 28 Compliance Certification Services (Kunshan) Inc. Page: 25 of 28 Compliance Certification Services (Kunshan) Inc. Page: 26 of 28 Compliance Certification Services (Kunshan) Inc. Page: 27 of 28 Compliance Certification Services (Kunshan) Inc. Page: 28 of 28 4 Impeda nce and re tur n loss Dipole CLA150 SN 4025 Head Liquid Date of Measurement Return Loss(dB) Δ % Impedance (Ω) ΔΩ 2021/4/26 -31.4 / 47.8 / Dipole D450V3 SN 1103 Head Liquid Date of Measurement Return Loss(dB) Δ % Impedance (Ω) ΔΩ 2021/4/21 -23 / 57.1 /

Compliance Certification Services (Kunshan) Inc. Page: 1 of 7 Appendix D for KSCR220400042006 Photographs 1. SAR measurement System 2. Photographs of Tissue Simulate Liquid 3. Photographs of EUT test position 4. EUT Antenna Locations 5. EUT Constructional Details Compliance Certification Services (Kunshan) Inc. Page: 2 of 7 1. SAR measurement System Compliance Certification Services (Kunshan) Inc. Page: 3 of 7 2. Photographs of Tissue Simulate Liquid Tissue Simulant Liquid for Head 750 Tissue Simulant Liquid for Head 835 Tissue Simulant Liquid for Head 1800 Tissue Simulant Liquid for Head 1900 Tissue Simulant Liquid for Head 2450 Tissue Simulant Liquid for Head 5GHz Compliance Certification Services (Kunshan) Inc. Page: 4 of 7 3. Photographs of EUT test position Back side 0mm Edge1 left 0mm Edge2 0mm Edge 3 0mm Compliance Certification Services (Kunshan) Inc. Page: 5 of 7 Edge 4 0mm Compliance Certification Services (Kunshan) Inc. Page: 6 of 7 4. EUT Antenna Locations Compliance Certification Services (Kunshan) Inc. Page: 7 of 7 5. EUT Constructional Details Details please Refer to Appendix – Photographs of EUT Constructional Details for KSCR2204000420AT.

Compliance Certification Services (Kunshan) Inc. Report No.: KSCR220400042006 Page: 1 of 110 Eric Lin EMC Laboratory Manager FCC SAR TEST REPORT Application No.: KSCR2204000420AT FCC ID: 2AAGE-TAB10RK664G Applicant: Chengdu Vantron Technology Co., Ltd. Address of Applicant: No.5 GaoPeng Road, Hi-Tech Zone, Chengdu, SiChuan, P.R. China Manufacturer: Chengdu Vantron Technology Co., Ltd. Address of Manufacturer: No.5 GaoPeng Road, Hi-Tech Zone, Chengdu, SiChuan, P.R. China Factory: Chengdu Vantron Technology Co., Ltd. Address of Factory: No.5 GaoPeng Road, Hi-Tech Zone, Chengdu, SiChuan, P.R. China Product Name: Tablet Model No.(EUT): M10 Pro FCC ID: 2AAGE-TAB10RK664G Standard(s) : FCC 47CFR §2.1093 Date of Receipt: 2022-08-01 Date of Test: 2022-08-02 to 2022-08-07 Date of Issue: 2022-11-08 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. Report No.: KSCR220400042006 Page: 2 of 110 REVISION HISTORY Revision Record Version Description Date Remark 00 Original 2022-11-08 / Authorized for issue by: Richard.Kong/ Project Engineer Eric.Lin/Reviewer Compliance Certification Services (Kunshan) Inc. Report No.: KSCR220400042006 Page: 3 of 110 TEST SUMMARY Frequency Band Maximum Reported SAR(W/kg) Body LTE Band 2 1.14 LTE Band 4 0.93 LTE Band 5 0.40 LTE Band 12 0.38 LTE Band 13 0.44 LTE Band 25 1.01 LTE Band 26 0.41 WI-FI (2.4GHz) 0.75 BT 0.61 WI-FI (5GHz) 0.84 WWAN + WIFI 2.4G 1.57 WWAN + BT 1.56 WWAN + WIFI 5G 1.28 SAR Limit(W/kg) 1.6 Maximum Simultaneous Transmission SAR (W/kg) Scenario Body WWAN + WIFI 2.4G 1.88 SPLSR 0.03 WWAN + BT 1.75 SPLSR 0.03 WWAN + WIFI 5G 1.98 SPLSR 0.04 SPLSR Limit 0.04 Compliance Certification Services (Kunshan) Inc. Report No.: KSCR220400042006 Page: 4 of 110 CONTENTS 1 GENERAL INFORMATION .............................................................................................................................. 6 1.1 GENERAL DESCRIPTION OF EUT .................................................................................................................. 6 1.1.1 DUT Antenna Locations ....................................................................................................................... 7 1.2 TEST SPECIFICATION ................................................................................................................................... 8 1.3 RF EXPOSURE LIMITS .................................................................................................................................. 9 1.4 TEST LOCATION ........................................................................................................................................ 10 1.5 TEST FACILITY .......................................................................................................................................... 10 2 LABORATORY ENVIRONMENT ................................................................................................................... 11 3 SAR MEASUREMENTS SYSTEM CONFIGURATION .................................................................................. 12 3.1 THE SAR MEASUREMENT SYSTEM ............................................................................................................ 12 3.2 ISOTROPIC E-FIELD PROBE EX3DV4 ......................................................................................................... 14 3.3 DATA ACQUISITION ELECTRONICS (DAE) ................................................................................................... 15 3.4 SAM TWIN PHANTOM ................................................................................................................................ 15 3.5 ELI PHANTOM ........................................................................................................................................... 16 3.6 DEVICE HOLDER FOR TRANSMITTERS ......................................................................................................... 17 3.7 MEASUREMENT PROCEDURE ...................................................................................................................... 18 3.7.1 Scanning procedure ........................................................................................................................... 18 3.7.2 Data Storage ...................................................................................................................................... 20 3.7.3 Data Evaluation by SEMCAD ............................................................................................................. 20 4 SAR MEASUREMENT VARIABILITY AND UNCERTAINTY ........................................................................ 22 4.1 SAR MEASUREMENT VARIABILITY ............................................................................................................... 22 4.2 SAR MEASUREMENT UNCERTAINTY ............................................................................................................ 23 5 DESCRIPTION OF TEST POSITION ............................................................................................................. 24 5.1 BODY TEST POSITION ................................................................................................................................ 24 5.2 PROXIMITY SENSOR TRIGGERING TEST ...................................................................................................... 25 6 SAR SYSTEM VERIFICATION PROCEDURE .............................................................................................. 28 6.1 TISSUE SIMULATE LIQUID ........................................................................................................................... 28 6.1.1 Recipes for Tissue Simulate Liquid .................................................................................................... 28 6.1.2 Test Liquids Confirmation ........................…

Text truncated - open the document above for the full version.

Compliance Certification Services (Kunshan) Inc. Report No.: KSCR220400042004 Page: 1 of 222 Eric Lin Laboratory Manager Test Report Application No.: KSCR2204000420AT FCC ID: 2AAGE-TAB10RK664G Applicant: Chengdu Vantron Technology Co., Ltd. Address of Applicant: No.5 GaoPeng Road, Hi-Tech Zone, Chengdu, SiChuan, P.R. China Manufacturer: Chengdu Vantron Technology Co., Ltd. Address of Manufacturer: No.5 GaoPeng Road, Hi-Tech Zone, Chengdu, SiChuan, P.R. China Factory: Chengdu Vantron Technology Co., Ltd. Address of Factory: No.5 GaoPeng Road, Hi-Tech Zone, Chengdu, SiChuan, P.R. China Equipment Under Test (EUT): EUT Name: Tablet Model No.: M10 Pro Trade Mark: Vantron Standard(s) : 47 CFR Part 15, Subpart E 15.407 Date of Receipt: 2022-04-02 Date of Test: 2022-04-09 to 2022-05-22 Date of Issue: 2022-07-28 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. CCS Report No.: KSCR220400042004 Page: 2 of 222 Revision Record Version Chapter Date Modifier Remark 01 2022-07-28 Original Authorized for issue by: Pawn.Liu/Project Engineer Eric Lin/Reviewer Compliance Certification Services (Kunshan) Inc. CCS Report No.: KSCR220400042004 Page: 3 of 222 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart E 15.407 N/A 47 CFR Part 15, Subpart C 15.203 Pass Transmission in the Absence of Data N/A 47 CFR Part 15, Subpart C 15.407 (c) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Emissions at AC Power Line (150kHz-30MHz) 47 CFR Part 15, Subpart E 15.407 ANSI C63.10 (2013) Section 6.2 47 CFR Part 15, Subpart C 15.207 & 15.407 b(6) Pass Duty Cycle KDB 789033 II B 1 KDB 789033 D02 II B 1 Pass 99% Bandwidth KDB 789033 II D N/A Pass 26dB Emission bandwidth KDB 789033 D02 II C 1 47 CFR Part 15, Subpart C 15.407 (a) Pass Minimum 6 dB bandwidth (5.725- 5.85 GHz band ) KDB 789033 D02 II C 2 47 CFR Part 15, Subpart C 15.407 (e) Pass Maximum Conducted output power KDB 789033 D02 II E 47 CFR Part 15, Subpart C 15.407 (a) Pass Peak Power spectrum density KDB 789033 D02 II F 47 CFR Part 15, Subpart C 15.407 (a) Pass Radiated Emissions (Above 1GHz) KDB 789033 D02 II G 47 CFR Part 15, Subpart C 15.209 & 15.407(b) Pass Radiated Emissions which fall in the restricted bands KDB 789033 D02 II G 47 CFR Part 15, Subpart C 15.209 & 15.407(b) Pass Frequency Stability ANSI C63.10 (2013) Section 6.8 47 CFR Part 15, Subpart C 15.407 (g) Pass Radiated Emissions (Below 1GHz) KDB 789033 D02 II G 47 CFR Part 15, Subpart C 15.209 & 15.407(b) Pass Compliance Certification Services (Kunshan) Inc. CCS Report No.: KSCR220400042004 Page: 4 of 222 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 TEST SUMMARY ....................................................................................................................................... 3 3 CONTENTS ................................................................................................................................................ 4 4 GENERAL INFORMATION ........................................................................................................................ 6 4.1 DETAILS OF E.U.T. ............................................................................................................................... 6 4.2 POWER LEVEL SETTING USING IN TEST: .................................................................................................. 6 4.3 ENVIRONMENT PARAMETER .................................................................................................................. 7 4.4 DESCRIPTION OF SUPPORT UNITS ......................................................................................................... 7 4.5 MEASUREMENT UNCERTAINTY .............................................................................................................. 7 4.6 TEST LOCATION .................................................................................................................................... 8 4.7 TEST FACILITY ...................................................................................................................................... 8 4.8 DEVIATION FROM STANDARDS ............................................................................................................... 9 4.9 ABNORMALITIES FROM STANDARD CONDITIONS ..................................................................................... 9 5 EQUIPMENT LIST .................................................................................................................................... 10 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................... 11 6.1 ANTENNA REQUIREMENT .................................................................................................................... 11 6.1.1 Test Requirement: ....................................................................................................................... 11 6.1.2 Conclusion ................................................................................................................................... 11 6.2 TRANSMISSION IN THE ABSENCE OF DATA ............................................................................................ 12 6.2.1 Test Requirement: ....................................................................................................................... 12 6.2.2 Conclusion ................................................................................................................................... 12 7 RADIO SPECTRUM MATTER TEST RESULTS ..................................................................................... 13 7.1 CONDUCTED EMISSIONS AT AC POWER LI…

Text truncated - open the document above for the full version.

                 !"#$%&'"(   ) *+, !"#$-."/$  ) 0 123456(789:; 00 123456(789:; 0 < =>?@A:."::7$ !"#9B9#7.9&:  < C DEF  $G7(7/"."($  C$$ HIEF J HIEFG7KK9'"$L"K.$ ) J$$M$N N =>OP5A:."::7$G(&B9Q" ) R$M$S R TUVW X7."(97Q$%"(.9B9#7."$ )C Y$M$0< S Z&[ \] Z&[ L"K.$Z"!&(.$ ^^ ^^ Y _`A _`A _`A aaa 7bbcdefghijklmnopCSqrs1tm L"QuYNJSaR)CRJYRJ v7wuYNJSaR)CRJYRJ$ )aaa 0aaa � 皿I尸1 E 2 I 3 I 4 I 5 I 6 I 7 I 8 CUSTOMER I I IREV. DESCRIPTION DATE PART NO I I I /& 首次发行 2021-11-15 座 修改 FPC 2021-12-27 心 修 改 线长 2022-01-06 I E 心 修改 FPC 2022-06-28 96.0 D Cl L.L寸 D c B B A l 3 I FPC 96.0*47.?mm FPC FPC11XXXA.P01 2 I Coaxial Cable O.D.1.13 G「ay O.D.1.13 GOA 1 OOXXA.P01 1 Mini Connector Au Plated 1代 Cu TER100XXA.P01 1 NO I PART NAME DESCRIPTION MaterialPart Number Q .TY 2 I 3 APPROVED BY PART NAME: L TE/DIV Antenna L=188mm MHF PART NO.: Y J � 01 .042.021.30 � A I DA Tf 2022-06 _ -28 ------ ------------ E3- - CHECKED BY DESIGNED BY 陈国强 周琪 廖光喜 1·01e「ance1 A x.x 士0.50 x.xx 土0.15 -5-6-7 UNITS: mm SCALE: 1/1 RE � ISIO N : D I X 0 士3 0 且
       !"#$ %&&'&&()*  !"#$ %&&+'&&()* ,%,&+-,.&()* /0123"#4&56705890:"3;5 <=>=?=@4=&5(3AB %&&+'&&()* -=4(3AB,%,&+-,.&()*-=45(3AB,%,&-,.&()* C3:" ,='52D:B %&&+'&&()* E=,52D:B ,%,&+-,.&()* @32:3F:9"60":+2:#F:9"3; G9;3:*3F:9"H:"3  IJ K9""#F9 ,L/GMN K3O;5P$16=Q=,=,R00 K3O;5H"SF7,..00 K3O;5K9;9C3$ 322TUVWXYZ[\]^_`a4'bcdef^ P;g&%h'+.-4.h&.h 3Ag&%h'+.-4.h&.h5 613F:"S5P01=+E&5i5j.45kK >F93S5P015l55)!0:2:F$ -4m4kK5l5n%&o

         !"#$%&'()*+,-./% 0123456*789)86486 :;3456*789)86486<
   
      
    !   "  # # $$ %  %!% %!% & #!   " ##  "  ##$ & #  #&$   $#""!%$#" "!% ! #! "%  $ %% "#  $ %&$ & ! $# %# &!  $% %" "# # $& #!# "&  $" #! "&  $ ## "$ " $#"$"!#
'()*+,-./01234"!567891 :;! $#"$$
<;! $#"$$ $#"$ "!# $$ # $ # $! #! $ % ! " $ 
   
 
      ! "#$ % ! $& "! ! % % "## " % ! "#$ ! %& $#$ "!# !  !! "$  ! !! "$# ! % ! "! $  $$ "!$  & $ "!$   $## "!# $
'()*+,-./01234#567891 :;&"%#%&%&
<;&"%#%&%& ! $ "#  % !& "& "



  !"#$%$" $" &' !"#$%$" $"(
     ! "#$%&'()*+*(&*( , -%&'()*+*(&*(.


         !"#$#%&'()!*)+!,-,!."/)0!12 3456573845   9)":;)<#:(!( =5>338?5=>8?34@A?@  (!,, 9BCB*:+0!(D


 EE35F385G  >@H=85I55=>8?  JB*:+0!(D >384I=8558K85L6E66 C)#)M(!N)(! O-*PJO*O- MQR"!*:+0!(&SR(";R(+)#$R"2M(!N)(!T%D UUVWXWYUXVVZ&;)[2UUVWXWYUXYU *R#!\T1)"],N)<!,)(!"R#N!(+$##!^;)"%$#!+$,"R# _+!(`!"<%MQR"!*:+0!()NN1$<)01!aR("R$";R(+)#$R"$,)b)$1)01!a#Q!,N)<! '!1![cdeGeddf6+:,#0!+)(]!#R$" $<)#!#Q)#^  345E34445574>8 45455F>5   *Pg_C_*'BJB*R^J.*'_*'B&h2.BOJPO &M_/2&'/i2 O!)b%)(R+#$<")NQ#Q)&N!#(R1!:+2VYY WjYWZkh*^C^*^C^ _NR[%W<(%1$<!($b)#$b!'()!,!<(!#kYUh*^C^*^C^ T)($:+,:1;)#!WYXWk
h:,#Z+`l+X
+`l+X B$1$<)a)+R(NQR:,a;:,!VXWUVWjkUh*^C^:,#'/i
+`l+X C$N(RN%1!"!`1%<R1+!#Q%1!#Q!(XYZj
WjYWUkh

NN+

NN+  345e8m8>5738 45   *O/'.*nO$`Q1%<R"<!"#()#!b)NR($(($#)#!,"R,!a#Q(R)#)"#)" 1:"`,^9)%<):,!Q!))<Q!)" $oo$"!,,^ _p_J.*'J'nB1$`Q#$(($#)#$R" Bq*J.*'J'nB1$`Q#$(($#)#$R" *P_B'.*nO)(+;:1a$;,r)11Rr!^  345G7>88=>    Bq*J.*'J'ns),Qr$#QN1!"#%R;r)#!(:,$"`),R)N^CR"R#:,!R(`)"$<,R1b!"#,^ _p_J.*'J'ng$",!$++!$)#!1%r$#Q<1!)"r)#!(;R()#1!),#Z+$":#!,^;$(($#)#$R"N!(,$,#,a,!!]+!$<)1)##!"#$R" *O/'.*n++!$)#!1%<)((%#Q!b$<#$+#R)…

Text truncated - open the document above for the full version.